In this communication an extended “in–out” polymerization method is presented, which leads to the synthesis of novel heteroarm star block terpolymers of the type An(B‐b‐C)n. A four step/one‐pot synthetic procedure is pursued using anionic polymerization under an inert atmosphere. The resulted star‐shaped terpolymer consists of a divinyl benzene nodule bearing pure polystyrene and poly(hexyl methacrylate)‐block‐poly(methyl methacrylate) diblock copolymer arms. It is shown that this kind of star terpolymers can self‐assemble in the bulk forming lamellae mesophase by arm and block segregation. The mechanical properties of the terpolymer have been examined in detail. Finally, the proposed synthetic procedure can be easily employed in other controlled polymerization methods.
A series of novel temperature and pH responsive block copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM) and poly(L ‐lysine) (PLL) were synthesized. The effect of pH and the length of PLL on the lower critical solution temperature (LCST) of PNIPAM, and the self‐assembly of these PLL‐based copolymers induced by temperature and pH changes were investigated by the cloud point method, dynamic light scattering (DLS) and environmental scanning electron microscopy (ESEM). These PNIPAM‐b‐PLL copolymers can self‐assemble into micelle‐like aggregates with PNIPAM as the hydrophobic block at acidic pH and high temperatures; and at alkaline pH and low temperatures, they can self‐assemble into particles with PLL as the hydrophobic block. The copolymers may have potential applications in biotechnological and biomedical areas as drug release carriers.
Summary: We synthesized for the first time novel pH‐responsive polyampholyte microgels consisting of poly(methacrylic acid) and poly(2‐(diethylamino)ethyl methacrylate) (PMAA‐PDEA) that are sterically stabilized with poly(ethylene glycol) methyl ether methacrylate (PEGMEM). These microgels showed enhanced hydrophilic behavior in aqueous medium at low and high pH but become hydrophobic and compact between pH 4 and 6 near the isoelectric point. Dynamic‐light scattering measurements showed that the hydrodynamic radius, Rh of these microgels is approximately 100 nm between pH 4 and 6 and increases to around 140 and 170 nm at pH 2 and 10, respectively. It is evident that the cross‐linked MAA‐DEA microgel that is sterically stabilized with PEGMEM retains the polyampholyte properties in solution.
Summary: A series of novel mesogen‐jacketed liquid crystal miktoarm star rod‐coil block copolymers were synthesized via atom transfer radical polymerization (ATRP). Their architectures {coil conformation of styrene segment and rigid rod conformation of {2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene} (MPCS) segment} were confirmed by GPC, 1H NMR, and MALDI‐TOF studies. The liquid crystalline behaviors of the synthesized copolymers are evidenced from POM observation. The liquid crystalline phase depends on the molecular weights of the rigid rod arm of miktoarm star copolymers.
A series of novel pH‐ and temperature‐responsive diblock copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM) and poly[(L ‐glutamic acid)‐co‐(γ‐benzyl L ‐glutamate)] [P(GA‐co‐BLG)] were prepared. The influence of hydrophobic benzyl groups on the phase transition of the copolymers was studied for the first time. With increasing BLG content in P(GA‐co‐BLG) block, the thermal phase transition of the diblock copolymer became sharper at a designated pH and the critical curve of phase diagram of the diblock copolymer shifted to a higher pH region. Notably, when the BLG content in P(GA‐co‐BLG) block was more than 30 mol.‐%, the diblock copolymer responded sharply to a narrow pH change in the region of pH 7.4–5.5.
A poly(methyl methacrylate)‐block‐poly(acrylic acid)‐block‐poly(2‐vinyl pyridine)‐block‐poly(acrylic acid)‐block‐poly(methyl methacrylate) (PMMA‐PAA‐P2VP‐PAA‐PMMA), pentablock terpolymer has been synthesized by anionic polymerization with sequential addition of monomers and studied in aqueous media at low pH. The system exhibits combined properties and adopts the behavior of ‘telechelic’ polyelectrolytes and that of double hydrophilic polyampholytes. This complex behavior leads to the pentablock terpolymer forming a pH and temperature sensitive reversible hydrogel at very low polymer concentration.
Metallo‐supramolecular core cross‐linked (CCL) micelles are fabricated from terpyridine‐functionalized double hydrophilic block copolymers, poly(2‐(2‐methoxyethoxy)ethyl methacrylate)‐b‐poly(2‐(diethylamino)ethyl methacrylate‐co‐4′‐(6‐methacryloxyhexyloxy)‐2,2′:6′,2″‐terpyridine) [PMEO2MA‐b‐P(DEA‐co‐TPHMA)] via the formation of bis(terpyridine)ruthenium(II) complexes. These metallo‐supramolecular CCL micelles exhibit not only high structural integrity under different pH values and temperatures in aqueous solution, but multistimuli responsiveness including pH‐responsive cores, thermo‐responsive shells, and reversible dissociation of bis(terpyridine)ruthenium(II) complexes upon addition of competitive metal ion chelator, which allows for precisely controlled release of the encapsulated hydrophobic guest molecules via the combination of different stimuli.
A novel pH‐responsive polymer vesicle obtained by the aqueous self‐assembly of carboxy‐terminated hyperbranched polyesters is reported. The synthesis is very simple, just a one‐step esterification of the commercially available hydroxy‐terminated hyperbranched polyester of Boltorn Hx (x = 20, 30, 40) with succinic anhydride. The vesicle size can be controlled from 200 nm to 10 µm by simply adjusting the solution pH as well as the degrees of branching (or generation).
Poly(2‐hydroxyethyl methacrylate)‐block‐poly(N‐isopropylacrylamide) (PHEMA‐b‐PNIPAM) was prepared by controlled surface‐initiated ATRP from silicon substrates, and the resulting block copolymers were successfully converted into the corresponding PSEMA‐b‐PNIPAM by esterification of the hydroxy groups on the PHEMA block using excess of succinic anhydride. The PSEMA‐b‐PNIPAM block copolymer brushes respond to both temperature and pH stimuli. The double‐responsive behavior of the block copolymer brushes in solution was investigated by height imaging and force–distance measurements of AFM. The results clearly show the responsive behavior of the smart block copolymer brushes.
Summary: Diblock terpolymers that consist of homopolymer and statistical copolymer (polyampholyte) building blocks are synthesized by group transfer polymerization. Two types of block tepolymers are explored in aqueous media: the amphiphilic poly{[(diethylamino)ethyl methacrylate]‐co‐(methacrylic acid)}‐block‐poly(methyl methacrylate) and the double hydrophilic poly[oligo(ethylene glycol) methacrylate]‐block‐poly{[(diethylamino)ethyl methacrylate]‐co‐(methacrylic acid)}. The first terpolymer self‐assembles in aqueous media to form responsive micelles that change their corona charge sign upon switching pH. The second terpolymer exhibits a multi‐responsive behavior. It forms neutral, positive, or negative micelles depending on a combination of different environmental conditions such as temperature, pH, and ionic strength.
Mixing a bis‐hydrophilic, cationic miktoarm star polymer with a linear polyanion leads to the formation of unilamellar polymersomes, which consist of an interpolyelectrolyte complex (IPEC) wall sandwiched between poly(ethylene oxide) brushes. The experimental finding of this rare IPEC morphology is rationalized theoretically: the star architecture forces the assembly into a vesicular shape due to the high entropic penalty for stretching of the insoluble arms in non‐planar morphologies. The transmission electron microscopy of vitrified samples (cryogenic TEM) is compared with the samples at ambient conditions (in situ TEM), giving one of the first TEM reports on soft matter in its pristine environment.
The free volume in thin films of poly(N‐isopropylacrylamid) end‐capped with n‐butyltriocarbonate (nbc‐PNIPAM) is probed with positron annihilation lifetime spectroscopy (PALS). The PALS measurements are performed as function of energy to obtain depth profiles of the free volume of nbc‐PNIPAM films. The range of nbc‐PNIPAM films with thicknesses from 40 to 200 nm is focused. With decreasing film thickness the free volume increases in good agreement with an increase in the maximum swelling capability of the nbc‐PNIPAM films. Thus in thin hydrogel films the sorption and swelling behavior is governed by free volume.
This paper describes a poly(dimethylsiloxane) (PDMS)‐based microfluidic platform for constructing the phase diagram of poly(N‐isopropyl acrylamide) (PNIPAM) in aqueous solution. The PNIPAM solution was delivered into a nanoliter chamber through the main microchannel. An osmotic pressure difference was established between the chamber and the control microchannel by flowing a high‐concentration salt solution in the control microchannel. Controlled evaporation of water resulted in increasing concentration of PNIPAM. A phase diagram of PNIPAM was built by measuring the cloud points at different concentrations, with a minimum point at ≈40 wt.‐%. The microfluidic platform has the advantages of low sample consumption and rapid heat exchange rates, and allows studying viscous polymer solution.
A series of thermo‐responsive PNIPAM copolymers containing different amounts of fulgimide moieties has been synthesized via a polymer analogous reaction of poly(pentafluorophenyl acrylate). All copolymers were designed to exhibit a lower critical solution temperature (LCST) in water, which was only weakly dependent on the amount of incorporated chromophoric fulgimide groups. The copolymers showed a photocyclization of the fulgimide side groups upon irradiation with UV‐light accompanied with a color change. The closed form of the chromophore had a halftime of 136 min for the visible reisomerization and did not affect the LCST of the polymer. This led to the realization of a logic “NOT A” for the fulgimide containing PNIPAM, while a corresponding azobenzene containing PNIPAM resulted in a different logic “A implies B”.
The fabrication of a thermoresponsive biohybrid double hydrophilic block copolymer (DHBC) by a cofactor reconstitution approach is reported. Poly(N‐isopropylacrylamide) (PNIPAM) bearing a porphyrin moiety at the chain terminal, PPIXZn‐PNIPAM, is synthesized by the combination of ATRP and a click reaction. The subsequent cofactor reconstitution process between apomyoglobin and PPIXZn‐PNIPAM affords well‐defined myoglobin‐b‐PNIPAM protein–polymer bioconjugates. Behaving as typical responsive DHBCs, the obtained myoglobin‐b‐PNIPAM biohybrid diblock copolymer exhibits thermo‐induced aggregation behavior in aqueous solution as a result of the presence of the thermoresponsive PNIPAM block, as revealed by temperature‐dependent transmittance, dynamic laser light scattering measurements, transmission electron microscopy, and scanning electron microscopy. This work represents the first report of the preparation of responsive biohybrid DHBCs by the cofactor reconstitution process.
Worm‐like aggregates with a PAA/P4VP complex core and a PEG/PNIPAM mixed shell were prepared in ethanol by the comicellization of poly(ethylene glycol)‐block‐poly(acrylic acid) (PEG‐b‐PAA) and poly(N‐isopropylacrylamide)‐block‐poly(4‐vinylpyridine) (PNIPAM‐b‐P4VP) through hydrogen‐bonding. The formed aggregates were studied by dynamic light scattering, static light scattering, 1H NMR, and transmission electron microscopy. The length of worm‐like aggregates could be adjusted by changing the weight ratio of W(PNIPAM‐b‐P4VP)/W(PEG‐b‐PAA). When the ratio changed from 20 to 150%, the length changed from about 100 nm to several microns, and the diameter stayed almost unchanged at about 15 nm.
Large scale of well‐ordered macroporous π‐conjugated polymer monoliths have been successfully prepared through a new approach using micrometer‐sized naphthalene crystals as templates. The macroporous monoliths of poly(p‐phenylenevinylene) (PPV) and poly(p‐phenyleneethynylene) (PPE) grew along the unidirectional freezing direction inside the template naphthalene crystals which lead to the formation of controlling morphologies and homogeneous diameters. The polymer monoliths show straight and lamella macroporous structures. The diameters of pores and the thickness of pore walls can be controlled by tuning the freezing temperature.
Summary: The fabrication of polymer diodes on a glass substrate by an ink‐jet printing technique is reported. Both an n‐type semiconductive polymer, poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐(1‐cyanovinylene)phenylene] (CN‐PPV), and a p‐type semiconductive polymer, polypyrrole (PPy) or poly(3,4‐ethylenedioxythiophene) (PEDOT), were printed through a piezoelectric ink‐jet printer. The printed CN‐PPV/PPy and CN‐PPV/PEDOT diodes showed good rectifying characteristics. These results indicate the potential of the low‐cost ink‐jet printing technique to produce polymer microelectronic devices and circuits.
Schematic diagram of the printed polymer diode 相似文献
Stimuli‐responsive polymers are the subject of intense research because they are able to show responses to various environmental changes. Among those stimuli, light has attracted much attention since it can be localized in time and space and it can also be triggered from outside of the system. In this paper, we review light‐responsive block copolymers (LRBCs) that combine characteristic features of block copolymers, e.g., self‐assembly behavior, and light‐responsive systems. The different photo‐responsive moieties that have been incorporated so far in block copolymers as well as the proposed applications are discussed.
A thermoresponsive block copolymer, namely poly(acryloyl glucosamine)‐block‐poly(N‐isopropylacryamide) (PAGA180‐b‐PNIPAAM350) was simultaneously self‐assembled and crosslinked in aqueous medium via RAFT polymerization at 60 °C to afford core‐crosslinked micelles exhibiting a glycopolymer corona and a PNIPAAM stimuli‐responsive core. An acid‐labile crosslinking agent, 3,9‐divinyl‐2,4,8,10‐tetraoxaspiro[5.5]undecane, was employed to generate thermosensitive and acid‐degradable core‐shell nanoparticles. Stable against degradation at pH = 6 and 8.2, the resulting core crosslinked micelles readily hydrolyzed into well‐defined free block copolymers at lower pH (30 min and 12 h respectively at pH = 2 and 4).
