A generalized silica coating scheme is used to functionalize and protect sub‐micron and micron size dicyclopentadiene monomer‐filled capsules and polymer‐protected Grubbs' catalyst particles. These capsules and particles are used for self‐healing of microscale damage in an epoxy‐based polymer. The silica layer both protects the capsules and particles, and limits their aggregation when added to an epoxy matrix, enabling the capsules and particles to be dispersed at high concentrations with little loss of reactivity.
We report here a facile synthesis of high performance electro‐active polymer actuator based on a sulfonated polyimide with well‐defined silver electrodes via self‐metallization. The proposed method greatly reduces fabrication time and cost, and obviates a cation exchange process required in the fabrication of ionic polymer‐metal composite actuators. Also, the self‐metallized silver electrodes exhibit outstanding metal‐polymer adhesion with high conductivity, resulting in substantially larger tip displacements compared with Nafion‐based actuators.
Summary: A soft‐lithographic imprinting approach to fabricate super‐hydrophobic surfaces has been developed in this work. In this process, fresh lotus leaves were used as masters and PDMS stamps were prepared by replica molding against the lotus‐leaf surfaces. By using the stamps and an epoxy‐based azo polymer solution as “ink”, the mimicked lotus‐leaf surfaces made of the polymer were fabricated by pressing the featured faces of the stamps against “inked” substrates and drying under a proper condition after peeling off the stamps. The lotus‐leaf‐like surfaces show super‐hydrophobic characteristics with the water contact angle higher than 150° and contact angle hysteresis less than 3°.
SEM images of lotus‐leaf‐like papillary structures on the imprinted surface. 相似文献
Supramolecular poly(vinyl acetate) PVAc 3‐arms stars were successfully generated by Reversible Addition–Fragmentation chain Transfer (RAFT)‐polymerized chains bearing hydrogen‐bonding heterocomplementary associating units. Chain Transfer Agents (CTA) bearing thymine‐ and diaminopyridine‐based units were first synthesized and proved to mediate efficiently the polymerization of VAc. The binding ability of the chains in solution was then demonstrated by 1H NMR and GPC measurements, proving the formation of the supramolecular stars.
A novel redox‐induced shape‐memory polymer (SMP) is prepared by crosslinking β‐cyclodextrin modified chitosan (β‐CD‐CS) and ferrocene modified branched ethylene imine polymer (Fc‐PEI). The resulting β‐CD‐CS/Fc‐PEI contains two crosslinks: reversible redox‐sensitive β‐CD‐Fc inclusion complexes serving as reversible phases, and covalent crosslinks serving as fixing phases. It is shown that this material can be processed into temporary shapes as needed in the reduced state and recovers its initial shape after oxidation. The recovery ratio and the fixity ratio are both above 70%. Furthermore, after entrapping glucose oxidase (GOD) in the system, the material shows a shape memory effect in response to glucose. The recovery ratio and the fixity ratio are also above 70%.
A comprehensive kinetic model is developed for a semi‐interpenetrating polymer network (SIPN) process, which involves simultaneous crosslinking, grafting, and degradation. Computational expense has been reduced considerably through a new component decomposition strategy, where a continuous variable approximation and a fixed pivot technique are applied for modeling each component. The inter‐polymer formulation is then reconstructed by a statistical approach. Based on the kinetic parameters obtained from the literature and a series of experiments, the model provides consistent agreement for gel fraction, joint molecular weight distribution (MWD) and polymer composition predicted in the studied cases, showing promising capability for the SIPN industrial application as well as for other polymer composite systems.
Summary: We describe an interesting approach to the fabrication of wettability gradients from hydrophobicity to superhydrophobicity in low‐density polyethylene (LDPE) films by first forming high porosity surfaces and placing the specimens onto linear temperature gradients. While the polymer chosen for the study is non‐polar, its microporous layer provides sufficient superhydrophobicity. Lateral gradient heating of the layer results in partial melting of the polymer and correspondingly decreases porosity thus decreasing hydrophobicity.
Camphor sulfonic acid (CSA) doped polyaniline (PANI) nanotubes (175 nm in outer diameter and 120 nm in inner diameter) were synthesized successfully by a self‐assembly method. It is found that the room‐temperature conductivity of an individual PANI nanotube is 30.5 S · cm−1; in particular, the intrinsic resistance of an individual nanotube (30 kΩ) is much smaller than the contact resistance of crossed nanotubes (500 kΩ).
A SEM image of two crossed PANI‐CSA nanotubes and the attached Pt electrodes. 相似文献
Summary: Ethylene and 10‐undecen‐1‐ol have been successfully copolymerized by an organically modified montmorillonite (OMMT)‐intercalated metallocene catalyst, Et[Ind]2ZrCl2, activated by methylaluminoxane (MAO). The obtained hydroxy‐functionalized polyethylene (PE‐OH)/OMMT nanocomposites exhibit enhanced structural stability as compared with the neat PE‐based ones, with no significant collapse of the nanocomposite structure being detected by WAXD examination after high‐temperature processing. The simultaneous polyolefin functionalization provides an effective and convenient solution to stabilize the PE/MMT nanocomposite structure formed by in‐situ polymerization.
Reactions between the ethylene groups in the backbone of conjugated polymers under UV illumination and heat treatment result in the cross‐linking of the main polymer chains. The cross‐linking leads to two simultaneous results in the polymer: excellent solvent resistance and increased bandgap. Using this reaction, three‐color polymer light‐emitting diodes (PLEDs) with a multi‐layer structure can be easily realized by a dry photo‐pattern in an active‐gas‐free environment. Multi‐layer blue devices with dramatically enhanced efficiency can also be achieved conveniently.
A novel kind of supramolecular liquid‐crystalline polymer (SLCP) microparticles was successfully fabricated with an azopyridyl polymer and sebacic acid by combining a simple self‐organized precipitation method with hydrogen bonding interactions. Upon slow evaporation of a mixed solution of a volatile good solvent and a nonvolatile poor one, walnutlike microparticles showing wrinkled surfaces and LC natures were obtained. The diacid might play a crucial role in the formation of SLCP particles. Without addition of the diacid, neither wrinkled surfaces nor LC natures were observed in azopyridyl polymer microparticles. The fabricated SLCP microparticle possessed not only photoresponsive properties (due to azopyridyl groups) but also LC ordering, which might enable them to find advanced applications.
An efficient procedure to create oriented polymer films with strongly anisotropic properties is described. It is based on a two‐step process combining a photochemical and a thermal aligning step. The orientation of the polymer parallel or perpendicular to linearly polarised incident light can be adjusted. The method presented allows for simple fabrication of films with anisotropic absorption and emission characteristics with a dichroism of 0.7 and a fluorescence anisotropy of about 8.
Summary: We have successfully constructed a redox‐responsible hydrogel system by combination of β‐cyclodextrin (β‐CD), dodecyl‐modified poly(acrylic acid) [p(AA/C12)], and a redox‐responsive guest, ferrocenecarboxylic acid (FCA). In the reduced state of FCA, the ternary mixture exhibited a gel‐like behavior, whereas, in its oxidized state, the mixture exhibited a sol behavior.
Conceptual illustration for the redox‐responsive hydrogel system. 相似文献
A polyvinylpyrrolidone (PVP)‐based fluorescent film with stable optical properties is successfully prepared in one pot without any additive. The reaction mechanism of ring‐opening and self‐crosslinking of linear PVP is proposed and demonstrated. The morphologies and the nanostructures of the fluorescent film as well as the unmodified film are investigated. The dye is incorporated into the film networks via covalent linkages, thus leading to the highly stable optical properties. The facile and effective synthesis approach opens a new way for the design of other multi‐functional composite materials based on linear PVP.
Summary: The fabrication of polymer diodes on a glass substrate by an ink‐jet printing technique is reported. Both an n‐type semiconductive polymer, poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐(1‐cyanovinylene)phenylene] (CN‐PPV), and a p‐type semiconductive polymer, polypyrrole (PPy) or poly(3,4‐ethylenedioxythiophene) (PEDOT), were printed through a piezoelectric ink‐jet printer. The printed CN‐PPV/PPy and CN‐PPV/PEDOT diodes showed good rectifying characteristics. These results indicate the potential of the low‐cost ink‐jet printing technique to produce polymer microelectronic devices and circuits.
Schematic diagram of the printed polymer diode 相似文献
Three‐dimensionally ordered macroporous (3DOM) syndiotactic polystyrene (sPS) and poly(p‐methyl styrene) (sPPMS) are synthesized using silica colloidal crystal templates with varied diameters in the range of 548–214 nm, and the effect of polymerization space on the conformation of the resulting 3DOM polymers is investigated by spectroscopy and thermal analysis. In‐situ polymerizations of styrene and p‐methyl styrene within the silica templates induce the resulting 3DOM polymers with different conformations and packing of chains, which are different from those of bulk polymers prepared in the absence of templates. Polymerizations in restricted silica templates result in un‐helixication of 3DOM sPS chains and helixication of 3DOM sPPMS chains.
Au nanoparticles (NPs) and polymer composite particles with phase‐separation structures were prepared based on phase separation structures. Au NPs were successfully synthesized in amphiphilic block‐copolymer micelles, and then composite particles were formed by a simple solvent evaporation process from Au NPs and polymer solution. The phase separated structures (Janus and Core‐shell) were controlled by changing the combination of polymers having differing hydrophobicity.
A precursor polymer PEO‐b‐PEMA that contains anilino moieties is synthesized from EPAEMA by ATRP by using a PEOBr macroinitiator and CuBr/HMTETA catalyst system. The aminoazobenzene‐containing block copolymer PEO‐b‐PCN is obtained by the azo‐coupling reaction between PEO‐b‐PEMA and the diazonium salt of 4‐aminobenzonitrile. Results show that PEO‐b‐PCN has a narrow molecular weight distribution and the repeat unit numbers of the hydrophilic and hydrophobic blocks are 122 and 200, respectively. PEO‐b‐PCN can form uniform spherical aggregates by gradually adding water into its THF solution. Upon irradiation with a linearly polarized Ar+ laser beam, the spherical aggregates can be significantly elongated in the polarization direction of the light.
Water‐soluble single‐ and multi‐walled carbon nanotubes (CNTs) were prepared by grafting polyacrylamide chains from the graphitic surface via ceric ion‐induced redox radical polymerization. The reducing functionalities were covalently attached to the tubes by peroxide‐assisted radical reaction. The results showed that polymer chains were grafted onto CNTs by the redox process. The redox radical polymerization initiated by carbon nanotube‐bearing functionalities not only provides a powerful strategy for modifying the carbon nanostructures but also gives us the knowledge of their sidewall chemistry.
The gecko adhesion phenomenon has stimulated efforts to produce synthetic patterned dry adhesives. Besides introducing surface patterns on dry adhesives, it is also highly desirable to understand their intrinsic material properties. This communication reports the viscoelastic behavior of non‐patterned epoxy elastomers exhibiting intrinsic adhesion that is much higher than that of elastomers typically used for structure patterning. The diverse molecular origin of the adhesion is revealed through the study of adhesion against various substrates.
