An effective computational algorithm for rate-independent crystal plasticity based on a single crystal yield surface with an application to tube hydroforming

Up to now, several computational methods have been proposed for crystal plasticity models. The main objective of these computational methods has been to overcome the problem with the non-uniqueness of active slip systems during the plastic deformation of a single crystal. Crystal plasticity models based on a single crystal yield function have been proposed as alternative algorithms to overcome this problem. But the problem with these models is that they use a highly non-linear yield function for the crystal, which makes them computationally expensive. In this paper, a computational method is proposed that would modify a single crystal yield function in order to make it computationally efficient. Also to better capture experimental data, a new parameter is introduced into the single crystal yield function to make it more flexible. For verification, this crystal plasticity model was directly applied for the simulation of hydroforming of an extruded aluminum tube under complex strain paths. It was found that the current model is considerably faster than the previous crystal plasticity model based on a power-law type single crystal yield surface. Due to its computational efficiency, the current crystal plasticity model can also be used to calculate the anisotropy coefficients of phenomenological yield functions.     

Interpretation of the behavior of metals under large plastic shear deformations: comparison of macroscopic predictions to physically based predictions

A large plastic shear problem is analyzed by application of a macroscopic anisotropic plasticity model (Kuroda, M., 1997. Interpretation of the behavior of metals under large plastic shear deformations: a macroscopic approach. Int. J. Plasticity 13, 359–383), and the results are compared to predictions based on crystal plasticity with the Taylor assumption. It is found that these two different-scale models provide very similar predictions. The interpretations for such similarities are pursued in detail. The present macroscopic model reproduces quite well the change in orientation of anisotropy, which is directly predicted in the crystal plasticity analyses as a macroscopic manifestation of texture development. Consequently, the predictions for the rotation of the yield surface by the different-scale models become very similar. It is clearly shown that, in a macroscopic sense, the rotation of the anisotropic yield surface is a main cause of the axial effects in large plastic shear deformation.     

A numerical study of crack tip constraint in ductile single crystals

In this work, the effect of crack tip constraint on near-tip stress and deformation fields in a ductile FCC single crystal is studied under mode I, plane strain conditions. To this end, modified boundary layer simulations within crystal plasticity framework are performed, neglecting elastic anisotropy. The first and second terms of the isotropic elastic crack tip field, which are governed by the stress intensity factor K and T-stress, are prescribed as remote boundary conditions and solutions pertaining to different levels of T-stress are generated. It is found that the near-tip deformation field, especially, the development of kink or slip shear bands, is sensitive to the constraint level. The stress distribution and the size and shape of the plastic zone near the crack tip are also strongly influenced by the level of T-stress, with progressive loss of crack tip constraint occurring as T-stress becomes more negative. A family of near-tip fields is obtained which are characterized by two terms (such as K and T or J and a constraint parameter Q) as in isotropic plastic solids.     

AN ANALYSIS OF THE EFFECTS OF SYMMETRICAL TILT GRAIN BOUNDARIES ON THE PLASTIC DEFORMATION

A numerical investigation on the simple polycrystals containing threesymmetrical tilt grain boundaries(GBs)is carried out within the framework of crystalplasticity which precisely considers the finite deformation and finite lattice rotation aswell as elastic anisotropy.The calculated results show that the slip geometry and theredistribution of stresses arising from the anisotropy and boundary constraint play animportant role in the plastic deformation in the simple polycrystals.The stress levelalong GB is sensitive to the load level and misorientation,and the stresses along GB aredistributed nonuniformly.The GB may exhibit a softening or strengthening feature,which depends on the misorientation angle.The localized deformation bands usuallydevelop accompanying the GB plastic deformation,the impingement of the localizedband on the GB may result in another localized deformation band.The yield stresseswith different misorientation angles are favorably compared with the experimentalresults.     

A cyclic plasticity model for single crystals

The Armstrong–Frederick type kinematic hardening rule was invoked to capture the Bauschinger effect of the cyclic plastic deformation of a single crystal. The yield criterion and flow rule were built on individual slip systems. Material memory was introduced to describe strain range dependent cyclic hardening. The experimental results of copper single crystals were used to evaluate the cyclic plasticity model. It was found that the model was able to accurately describe the cyclic plastic deformation and properly reflect the dislocation substructure evolution. The well-known three distinctive regimes in the cyclic stress–strain curve of the copper single crystals oriented for single slip can be reproduced by using the model. The model can predict the enhanced hardening for crystals oriented for multislip, showing the model's ability to describe anisotropic cyclic plasticity. For a given loading history, the model was able to capture not only the saturated stress–strain response but also the detailed transient stress–strain evolution. The model was used to predict the cyclic plasticity under a high–low loading sequence. Both the stress–strain responses and the microstructural evolution can be appropriately described through the slip system activation.     

考虑运动硬化的DD3镍基合金力学行为研究

详细介绍了镍基合金的晶体塑性本构模型,在Asaro大变形晶体塑性框架下,详细介绍了镍基合金的晶体塑性本构模型,在Asaro大变形晶体塑性框架下,引入了运动硬化规律,考虑了温度和应变率对晶体塑性变形的影响,通过针对每个滑移系考虑屈服准则和流动规律建立了晶体塑性模型. 对积分过程进行了推导,通过编写ABAQUS材料用户子程序(UMAT), 实现本构模型的有限元积分算法. 在此基础上模拟了DD3镍基单晶合金在单轴拉伸和循环载荷下的响应,并与实验数据进行了对比. 利用该模型可以很好地模拟镍基单晶所具有的各向异性特性,体现了镍基单晶在循环载荷作用下的拉-压不对称性.      

位移加载条件下微小尺寸单晶金属的应变突变模型及其间歇性塑性变形行为研究

微压缩实验发现,微小尺度单晶金属柱体在塑性变形过程中会发生显著的应变突变,呈现出特殊的间歇性塑性流动特征。本文以数百纳米直径的单晶Au柱体为研究对象,探讨其在位移加载条件下的间歇性流动行为。首先根据位移加载条件下的塑性变形特征,提出了分析其应变突变的三阶段模型。进一步结合经典晶体塑性理论框架的有限元方法,建立了以二阶功参量为基础的连续塑性力学模型。通过与实验结果相对比发现,新模型能够较好地描述位移加载条件下微小尺度面心立方单晶金属材料的应变突变现象,能够合理预测单晶柱体的特殊变形行为。此外,二阶功准则作为位移加载条件下应变突变现象的判据是有效的。进而使用该理论模型,探讨了微小金属柱体应变突变随机性、尺寸相关性以及率敏感性等问题。     

结构拓扑优化局部性能约束下轻量化问题的互逆规划解法

瞄准应力和疲劳两类局部性能约束的结构拓扑优化问题,概括为分部、化整和集成3种解法和交融的3种解法.类比应力约束推导了疲劳寿命情况,一为满疲劳公式,二为疲劳寿命约束全局化的结构寿命概念和相应解法.在倒寿命概念下,实现了疲劳寿命约束与应力约束的规格统一.补充和完整了已有的局部性能约束解法,属于单目标模型,有分部、化整、集成三种.基于互逆规划理论的定理2,提出了交融优化解法,是单目标与多目标模型的交替迭代,有分部-集成、化整-集成和集成-集成三种.上述6种解法皆基于ICM方法进行建模.算例表明,新提出的交融优化方法提高了求解效率.     

On the strain hardening and texture evolution in high manganese steels: Experiments and numerical investigation

We present a systematic investigation on the strain hardening and texture evolution in high manganese steels where twinning induced plasticity (TWIP) plays a significant role for the materials' plastic deformation. Motivated by the stress–strain behavior of typical TWIP steels with compositions of Fe, Mn, and C, we develop a mechanistic model to explain the strain-hardening in crystals where deformation twinning dominates the plastic deformation. The classical single crystal plasticity model accounting for both dislocation slip and deformation twinning are then employed to simulate the plastic deformation in polycrystalline TWIP steels. While only deformation twinning is activated for plasticity, the simulations with samples composed of voronoi grains cannot fully capture the texture evolution of the TWIP steel. By including both twinning deformation and dislocation slip, the model is able to capture both the stress–strain behaviors and the texture evolution in Fe–Mn–C TWIP steel in different boundary-value problems. Further analysis on the strain contributions by both mechanisms suggests that deformation twinning plays the dominant role at the initial stage of plasticity in TWIP steels, and dislocation slip becomes increasingly important at large strains.     

基于晶体塑性理论研究铝材料高压高应变率下的强度特性

为了了解金属材料在极端加载下复杂动态响应过程中的多种机制和效应,重点针对Al材料在高压、高应变率加载下的塑性变形机制,在经典晶体塑性模型的基础上,对其中的非线性弹性、位错动力学和硬化形式进行改进,建立适用于高压、高应变率加载下的热弹-黏塑性晶体塑性模型。该模型可以较好地描述单晶铝和多晶铝材料屈服强度随压力的变化过程,相比宏观模型,用该模型还获得了多晶Al材料在冲击加载下的织构演化规律,揭示了织构择优取向行为和压力的关系。     

A finite strain elastic-viscoplastic self-consistent model for polycrystalline materials

A large strain elastic-viscoplastic self-consistent (EVPSC) model for polycrystalline materials is developed. At single crystal level, both the rate sensitive slip and twinning are included as the plastic deformation mechanisms, while elastic anisotropy is accounted for in the elastic moduli. The transition from single crystal plasticity to polycrystal plasticity is based on a completely self-consistent approach. It is shown that the differences in the predicted stress-strain curves and texture evolutions based on the EVPSC and the viscoplastic self-consistent (VPSC) model proposed by Lebensohn and Tomé (1993) are negligible at large strains for monotonic loadings. For the deformations involving unloading and strain path changes, the EVPSC predicts a smooth elasto-plastic transition, while the VPSC model gives a discontinuous response due to lack of elastic deformation. It is also demonstrated that the EVPSC model can capture some important experimental features which cannot be simulated by using the VPSC model.     

Non-local crystal plasticity model with intrinsic SSD and GND effects

A strain gradient-dependent crystal plasticity approach is presented to model the constitutive behaviour of polycrystal FCC metals under large plastic deformation. In order to be capable of predicting scale dependence, the heterogeneous deformation-induced evolution and distribution of geometrically necessary dislocations (GNDs) are incorporated into the phenomenological continuum theory of crystal plasticity. Consequently, the resulting boundary value problem accommodates, in addition to the ordinary stress equilibrium condition, a condition which sets the additional nodal degrees of freedom, the edge and screw GND densities, proportional (in a weak sense) to the gradients of crystalline slip. Next to this direct coupling between microstructural dislocation evolutions and macroscopic gradients of plastic slip, another characteristic of the presented crystal plasticity model is the incorporation of the GND-effect, which leads to an essentially different constitutive behaviour than the statistically stored dislocation (SSD) densities. The GNDs, by their geometrical nature of locally similar signs, are expected to influence the plastic flow through a non-local back-stress measure, counteracting the resolved shear stress on the slip systems in the undeformed situation and providing a kinematic hardening contribution. Furthermore, the interactions between both SSD and GND densities are subject to the formation of slip system obstacle densities and accompanying hardening, accountable for slip resistance. As an example problem and without loss of generality, the model is applied to predict the formation of boundary layers and the accompanying size effect of a constrained strip under simple shear deformation, for symmetric double-slip conditions.     

Dislocation Microstructures and the Effective Behavior of Single Crystals

We consider single-crystal plasticity in the limiting case of infinite latent hardening, which signifies that the crystal must deform in single slip at all material points. This requirement introduces a nonconvex constraint, and thereby induces the formation of fine-scale structures. We restrict attention throughout to linearized kinematics and deformation theory of plasticity, which is appropriate for monotonic proportional loading and confers the boundary value problem of plasticity a well-defined variational structure analogous to elasticity.We first study a scale-invariant (local) problem. We show that, by developing microstructures in the form of sequential laminates of finite depth, crystals can beat the single-slip constraint, i.e., the macroscopic (relaxed) constitutive behavior is indistinguishable from multislip ideal plasticity. In a second step, we include dislocation line energies, and hence a length scale, into the model. Different regimes lead to several possible types of microstructure patterns. We present constructions which achieve the various optimal scaling laws, and discuss the relation with experimentally known scalings, such as the Hall-Petch law.This revised version was published in April 2005. The volume number has now been inserted into the citation line.     

Forming simulation of aluminum sheets using an anisotropic yield function coupled with crystal plasticity theory

This paper describes the application of a coupled crystal plasticity based microstructural model with an anisotropic yield criterion to compute a 3D yield surface of a textured aluminum sheet (continuous cast AA5754 aluminum sheet). Both the in-plane and out-of-plane deformation characteristics of the sheet material have been generated from the measured initial texture and the uniaxial tensile curve along the rolling direction of the sheet by employing a rate-dependent crystal plasticity model. It is shown that the stress–strain curves and R-value distribution in all orientations of the sheet surface can be modeled accurately by crystal plasticity if a “finite element per grain” unit cell model is used that accounts for non-uniform deformation as well as grain interactions. In particular, the polycrystal calculation using the Bassani and Wu (1991) single crystal hardening law and experimental electron backscatter data as input has been shown to be accurate enough to substitute experimental data by crystal plasticity data for calibration of macroscopic yield functions. The macroscopic anisotropic yield criterion CPB06ex2 (Plunkett et al., 2008) has been calibrated using the results of the polycrystal calculations and the experimental data from mechanical tests. The coupled model is validated by comparing its predictions with the anisotropy in the experimental yield stress ratio and strain ratios at 15% tensile deformation. The biaxial section of the 3D yield surface calculated directly by crystal plasticity model and that predicted by the phenomenological model calibrated with experimental and crystal plasticity data are also compared. The good agreement shows the strength of the approach. Although in this paper, the Plunkett et al. (2008) yield function is used, the proposed methodology is general and can be applied to any yield function. The results presented here represent a robust demonstration of implementing microscale crystal plasticity simulation with measured texture data and hardening laws in macroscale yield criterion simulations in an accurate manner.     

A plasticity model for cellular materials with open-celled structure

Based on a rigid-plastic material model that obeys the von Mises yield criterion, the plastic behavior of foams with an open-celled structure is studied in this paper using a single unit cell. An approximate continuum plasticity model is developed within the framework of the upper bound theorem of plasticity to describe the yield behavior of foams. The microscopic velocity fields are derived for the unit cell, which satisfy the incompressibility and the kinematic boundary conditions, and expressed in macroscopic rate of deformation. From the microscopic velocity fields, a macroscopic yield function is developed for foams under multi-axial stresses and includes the effects of the hydrostatic stress due to the void presence and growth. The dependency of the derived yield surfaces of foams on their relative densities is studied. The plastic behavior of foams is also studied numerically using the finite element method. The newly developed plasticity model is compared with the finite element analysis results and other available foam models and then correlated with the finite element results.     

Qualitative Distinctions in the Solutions Based on the Plasticity Theories with the Mohr-Coulomb Yield Criterion

The following two models of the plasticity theory are considered: the model with the Mohr-Coulomb yield criterion and the classical model of the plasticity theory with a yield criterion independent of the mean stress. The deformation problem of a plastic layer enclosed between two rotating plates is studied. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 6, pp. 136–145, November–December, 2005.     

HILL屈服准则与晶体塑性模型对FCC单晶材料塑性各向异性描述能力的比较

采用宏观HILL模型和晶体塑性模型对面心立方单晶(FCC)材料的非均匀交形进行了数值模拟，意在比较两种不同尺度的模型对塑性各向异性的描述能力的差异。为了使两种模型具有可比性，对于FCC单晶材科，本文提出一种用晶体塑性模型来确定HILL模型中各向异性参数的标定方法。数值分析表明，两类模型对单晶体塑性各向异性的描述能力存在着差异。对FCC单晶材料，HILL模型对各向异性的预测能力没有晶体塑性模型细致，晶体塑性模型更能追踪塑性各向异性的变化。但两种模型对应力应变响应预测的趋势是一致的。对两种模型描述的差异，做了详细的分析。     

Effect of secondary orientation on notch-tip plasticity in superalloy single crystals

Numerical and experimental evolutions of slip fields in notched Ni-Base Single Crystal superalloy tensile specimens are presented as a function of secondary crystallographic orientation. The numerical predictions based on three-dimensional anisotropic elasticity and crystal plasticity are compared with experimental observations. The results illustrate the strong dependence of the slip patterns and the plastic zone size and shape on the secondary orientation of notches, which can have important consequences on crack initiation. Specific orientations or non-symmetric notch geometries lead to non-symmetric patterns on both sides of the sample. The computations show that strongly different plastic zones are expected in the core of the sample and at free surfaces. The ability of the anisotropic elastic model to anticipate the plastic domains, based on identifying dominant slip systems, is confirmed by the crystal plasticity computations, at low load levels. An important observation is that kink shear banding is a real deformation mode operating at crack tips and notches in high strength nickel-based single crystal superalloys for specific orientations.     

Dislocation pile-ups in bicrystals within continuum dislocation theory

Within continuum dislocation theory the plastic deformation of bicrystals under a mixed deformation of plane constrained uniaxial extension and shear is investigated with regard to the nucleation of dislocations and the dislocation pile-up near the phase boundaries of a model bicrystal with one active slip system within each single crystal. For plane uniaxial extension, we present a closed-form analytical solution for the evolution of the plastic distortion and of the dislocation network in the case of symmetric slip planes (i.e. for twins), which exhibits an energetic as well as a dissipative threshold for the dislocation nucleation. The general solution for non-symmetric slip systems is obtained numerically. For a combined deformation of extension and shear, we analyze the possibility of linearly superposing results obtained for both loading cases independently. All solutions presented in this paper also display the Bauschinger effect of translational work hardening and a size effect typical to problems of crystal plasticity.