退火对ZnO薄膜晶体结构和ZnO/p-Si异质结光电性质的影响

采用脉冲激光沉积方法在p-Si(100)衬底卜牛长ZnO薄膜,分别在500℃、600℃和700℃下真空退火,采用X射线衍射仪研究了退火对ZnO薄膜品体结构的影响,并测量了ZnO的面电阻和ZnO/p-Si异质结的、I-V特性曲线.研究表明,随着退火温度的升高,ZnO的(002)衍射峰强度逐渐增大,半峰全宽不断减小,同时薄膜内应力减小,ZnO晶粒尺寸变大.表明高温退火有助于ZnO薄膜结晶质量的提高.在没有光照的条件下,异质结的漏电流随退火温度的增加而增大;用650 nm光照射样品时,600℃退火的样品表现出最明显的光电效应,而过高的退火温度会破坏ZnO/p-Si异质结的界面结构,使其光电流变小.所以,要得到性能良好的光电器件,应选取适当的退火温度.     

Synthesis and characterization of ZnO/ZnSe NWs/PbS QDs solar cell

Journal of Nanoparticle Research - Nanosized nickel phosphide (Ni2P) has been synthesized via hydrothermal reaction with environmental-friendly red phosphorus and nickel chloride. The reaction...     

Growth of Cu2S/CdS nano-layered photovoltaic junctions for solar cell applications

Layered Cu₂S/CdS photovoltaic p-n junctions were fabricated via a simple and reproducible route. CdS inner layer was grown on ITO substrate using chemical bath deposition process for different times. The utilized bath consisted of cadmium sulfate and thiourea with concentrations of 0.05 M and 0.07 M, respectively. CdS layer grown for 600 min was uniform with a thickness of about 500 nm. Moreover, band gap energy of the CdS inner layers was measured as 2.40-2.44 eV depending on the thickness of the layer. Cu₂S outer layer was formed over the CdS via ion exchange chemical route, in a bath consisting of copper chloride aqueous solution. EDS, XRD, and XPS were utilized to characterize the formation of cadmium sulfide, and copper sulfide phases during the fabrication steps of the p-n junctions. Nano-layered cell, each layer 200-250 nm in thickness was fabricated with an apparent band gap of 2.22 eV. SEM imaging of both inner and the outer layers confirmed the uniformity and homogeneity of the CdS and the Cu₂S layers.     

Synthesis of ZnO nanoplates decorated rhombus-shaped ZnO nanorods and their application in solar cells

Novel nanostructures of ZnF(OH) nanoplates decorated rhombus-shaped ZnF(OH) nanorods were fabricated. The obtained precursors were transformed by calcination to porous hierarchical ZnO nanostructures with the original morphologies retained. Field emission scanning electron microscope images exhibit that the nanoplates are grown in the interstices between the nanorods and on the top of the nanorods. The structure and composition of the obtained products have been confirmed by transmission electron microscope and X-ray diffraction measurements. The obtained ZnO nanostructures have been successfully used in solar cells. The light-to-electricity conversion results show that the complex nanostructures exhibit a power conversion efficiency of 1.36% with a photoelectrode thickness of 4.2 µm, which is comparable to those based on 40 µm vertically aligned hexagonal-shaped ZnO nanowire array photoelectrodes. These results indicate that the synthesized ZnO nanoplate decorated rhombus-shaped ZnO nanorod nanostructures are more suitable for application as a photoelectrode in solar cells.     

Post-fabrication annealing effects on the performance of P3HT:PCBM solar cells with/without ZnO nanoparticles

In this study, P3HT:PCBM organic photovoltaic (OPV) devices, with or without ZnO nanoparticles buffer layer between the photoactive layer (P3HT:PCBM) and the cathode (Al top electrode), were fabricated. The devices were annealed at 145 °C either before or after depositing the top electrode. The objective of this study was to investigate the effects of the ZnO buffer layer and pre-/post-fabrication annealing on the general performance of these devices. The short-circuit current density (J_SC), open-circuit voltage (V_OC) and the external quantum efficiency (EQE) of the OPV devices were improved by the insertion of the ZnO layer and post-fabrication annealing. The post-fabrication annealed devices, with or without the ZnO layer, exhibited higher values of J_SC, V_OC and EQE than those of similar devices annealed before depositing the Al metal. This can be attributed to, among other things, improved charge transport across the interface between the photoactive layer and the Al top electrode as a result of post-annealing induced modification of the interface morphology.     

Growth and characterization of type-II ZnO/ZnTe core-shell nanowire arrays for solar cell applications

Large area, well-aligned type-II ZnO/ZnTe core-shell nanowire arrays have been fabricated on an a-plane sapphire substrate. The ZnO nanowires were grown in a furnace by chemical vapor deposition with gold as catalyst and then were coated with a ZnTe shell on the ZnO nanowires surface by a metal-organic chemical deposition chamber. The morphology and size distribution of the ZnO/ZnTe core-shell nanowire arrays were studied by scanning electron microscopy (SEM) and the crystal structure was examined by x-ray diffraction (XRD). Transmission measurement was used to study the optical properties of the core-shell nanowires. The results indicated that the ZnO/ZnTe core-shell nanowire arrays have good crystalline quality. In addition, it was found that the nanowire arrays have good light absorption characteristics and these properties make it suitable for making photovoltaic devices.     

The fabrication and characterization of ZnO UV detector

ZnO films were deposited on GaAs substrates by radio frequency (rf) magnetron sputtering followed by an ambient-controlled heat treatment process for arsenic doping. In Hall measurements, the As-doped ZnO films showed the characteristics of p-type semiconductor. The ZnO thin film p–n homojuctions were then fabricated to investigate the electrical properties of the films. The p–n homojunctions exhibited the distinct rectifying current–voltage (I–V) characteristics. The turn-on voltage was measured to be 3.0 V under the forward bias. When ultraviolet (UV) light (λ = 325 nm) was irradiated on the p–n homojunction, photocurrent of 2 mA was detected. Based on these results, it is proposed that the p–n homojunction herein is a potential candidate for UV photodetector and optical devices.     

XPS characterization of sensitized n-TiO2 thin films for dye-sensitized solar cell applications

TiO₂ thin films, employed in dye-sensitized solar cells, were prepared by the sol-gel method or directly by Degussa P25 oxide and their surfaces were characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The effect of adsorption of the cis-[Ru(dcbH₂)₂(NCS)₂] dye, N3, on the surface of films was investigated. From XPS spectra taken before and after argon-ion sputtering procedure, the surface composition of inner and outer layers of sensitized films was obtained and a preferential etching of Ru peak in relation to the Ti and N ones was identified. The photoelectrochemical parameters were also evaluated and rationalized in terms of the morphological characteristics of the films.     

Photoreflectance study on the photovoltaic effect in InAs/GaAs quantum dot solar cell

To investigate the effect of quantum dot (QD) layers on the photovoltaic process of InAs/GaAs QD solar cell (QDSC), QD layers were embedded in conventional GaAs p-n junction SC (GaAs SC) structures. The photoreflectance (PR) was examined at different temperatures (T) and excitation light intensities (I_ex) to investigate the photovoltaic effects through observation of the Franz-Keldysh oscillations (FKOs) in the PR spectra. The evaluated the p-n junction electric fields (F_pn) of the InAs QDSC was different from that of the GaAs SC. Moreover, InAs QDSC show that the different photovoltaic behaviors compared with GaAs SC by varying I_ex and T. From these considerations, we suggest that the different photovoltaic behaviors are caused by the effect of the additional photo-carrier generation in InAs QD layers resulting in enhancement of the field screening effect in F_pn.     

Adsorption of 1,2-diaminoethane on ZnO thin films from p-xylene

The interaction of 1,2-diaminoethane (DAE) with ZnO thin films prepared by electrodeposition and magnetron sputtering was investigated by X-ray photoelectron spectroscopy (XPS). The samples were exposed to organic solution of 0.5 M DAE-p-xylene in an Ar atmosphere glove box (O₂ and H₂O <5 ppm), directly connected to the XPS analysis chamber by an anaerobic and anhydrous transfer system. A clear interaction of DAE with the ZnO surface is evidenced by the presence of a high intensity N1s peak at BE = 399.5 ± 0.2 eV and C1s at BE = 286.3 ± 0.2 eV which are attributed to C-N bonding. The atomic ratio C:N was very close to 1:1 consistent with the molecular, non-dissociative adsorption of DAE on the ZnO layer. No significant difference in adsorption of DAE was observed for three different ZnO surfaces despite slight differences in their acid/base properties as evidenced by the O/OH ratio. The results are interpreted in terms of adsorption on Brönsted acid sites. A uniform layer model was used to approximate the DAE film thickness, which was found to be around 10 Å on three studied samples. The N1s and C1s_B signals were observed to decrease on sample exposure to vacuum and/or X-ray irradiation and additional N1s_B peak appeared at lower binding energy at around 398.5 ± 0.2 eV. This is interpreted by the desorption and modification of DAE, indicating low stability of the adsorbed state on ZnO. The exposure to water of the sample with adsorbed DAE causes a significant decrease of the N1s_A and C1s_B peak intensities attributed to the adsorbed DAE molecule, demonstrating the instability of the DAE-ZnO interface in water.     

Electrodeposition of zinc oxide/tetrasulfonated copper phthalocyanine hybrid thin film for dye-sensitized solar cell application

Hybrid film of zinc oxide (ZnO) and tetrasulfonated copper phthalocyanine (TSPcCu) was grown on an indium tin oxide (ITO) glass by one-step cathodic electrodeposition from aqueous mixtures of Zn(NO₃)₂, TSPcCu and KCl. The addition of TSPcCu strongly influences the morphology and crystallographic orientation of the ZnO. The nanosheets stack of ZnO leads to a porous surface structure which is advantageous to further adsorb organic dyes. The photovoltaic properties were investigated by assembling the DSSC device based on both the only ZnO film and the ZnO/TSPcCu hybrid films. Photoelectrochemical analysis revealed that the optimized DSSC device with TSPcCu represented a more than three-fold improvement in power conversion efficiency than the device without TSPcCu. The DSSC based on ZnO/TSPcCu hybrid films demonstrates an open circuit voltage of 0.308 V, a short circuit current of 90 μA cm⁻², a fill factor of 0.26, and a power conversion efficiency of 0.14%.     

Influence of growth temperature and post-annealing on an n-ZnO/p-GaN heterojunction diode

We report on an n-ZnO/p-GaN heterojunction diode fabricated from zinc oxide (ZnO) films at various growth temperatures (450, 500, 550, and 600 °C) by RF sputtering. The films were subsequently annealed at 700 °C in N₂ ambient. To investigate the influence of the growth temperature of n-ZnO films, the microstructural, optical, and electrical properties were measured using scanning electron microscopy (SEM), X-ray diffraction (XRD), photoluminescence (PL), and Hall measurements. The XRD pattern showed the preferred orientation along the c-axis (002) regardless of growth temperature. The PL spectra showed a dominant sharp near-band-edge (NBE) emission. Current–voltage (I–V) curves showed excellent rectification behavior. The turn-on voltage of the diode was observed to be 3.2 V for the films produced at 500 °C. The ideality factor of ZnO film was observed to be 1.37, which showed the best performance of the diode.     

Improved performance of a crystalline silicon solar cell based on ZnO/PS anti-reflection coating layers

A porous silicon (PS) layer was prepared by photoelectrochemical etching (PECE), and a zinc oxide (ZnO) film was deposited on a PS layer using a radio frequency (RF) sputtering system. The surface morphology of the PS and ZnO/PS layers was characterised using scanning electron microscopy (SEM). Nano-pores were produced in the PS layer with an average diameter of 5.7 nm, which increased the porosity to 91%. X-ray diffraction (XRD) of the ZnO/PS layers shows that the ZnO film is highly oriented along the c-axis perpendicular to the PS layer. The average crystallite size of the PS and ZnO/PS layers are 17.06 and 17.94 nm, respectively. The photoluminescence (PL) emission spectra of the ZnO/PS layers present three emission peaks, two peaks located at 387.5 and 605 nm due to the ZnO nanocrystalline film and a third located at 637.5 nm due to nanocrystalline PS. Raman measurements of the ZnO/PS layers were performed at room temperature (RT) and indicate that a high-quality ZnO nanocrystalline film was formed. Optical reflectance for all the layers was obtained using an optical reflectometer. The lowest effective reflectance was obtained for the ZnO/PS layers. The fabrication of crystalline silicon (c-Si) solar cells based on the ZnO/PS anti-reflection coating (ARC) layers was performed. The I–V characteristics of the solar cells were studied under 100 mW/cm² illumination conditions. The ZnO/PS layers were found to be an excellent ARC and to exhibit exceptional light-trapping at wavelengths ranging from 400 to 1000 nm, which led to a high efficiency of the c-Si solar cell of 18.15%. The ZnO/PS ARC layers enhance and increase the efficiency of the c-Si solar cell. In this paper, the fabrication processes of the c-Si solar cell with ZnO/PS ARC layers are an attractive and promising technique to produce high-efficiency and low-cost of c-Si solar cells.     

Fabrication and electrical characterization of p-Sb2S3/n-Si heterojunctions for solar cells application

Antimony trisulphide (Sb₂S₃) films were prepared by thermal evaporation technique on n-type single crystal Si substrates to fabricate p-Sb₂S₃/n-Si heterojunctions. The electrical transport properties of the p–Sb₂S₃/n-Si heterojunctions were investigated by current–voltage (I–V) and capacitance–voltage (C–V) measurements. The temperature-dependent I–V characteristics revealed that the forward conduction was determined by multi-step tunnelling current and the activation energy of saturation current was about 0.54 eV. The 1/C²–V plots indicated the junction was abrupt and the junction built-in potential was 0.6 V at room temperature and decreased with increasing temperature. The solar cell parameters have been calculated for the fabricated cell as V_oc = 0.50 V, J_sc = 14.53 mA cm⁻², FF = 0.32 and η = 4.65% under an illumination of 50 mW cm⁻².     

Characterization of a green and environmentally friendly sensitizer for a low cost dye-sensitized solar cell

Clean and cheap device, namely dye-sensitized solar cells (DSSCs) were fabricated using a natural dye extracted from Sambucus ebulus. We prepared five sample solutions with various pH in the extraction process to improve power conversion efficiency. The UV–visible absorption investigation of sample solutions and on photoanode show the dyes from J-type aggregation on a photoanode substrate. Redox properties of all sample solutions certify thermodynamically a charge transfer from excited state to conduction band TiO₂. The optical properties of various dye solutions were investigated and results showed darkness and bluish tint effect of dye solutions extracted in basic environment rather than those extracted in acidic condition. Moreover, in comparison to the basic condition, the dye solutions extracted in acidic environment were more saturated and colorimetrically less different from that one which extracted in neutral condition. Photophysical and photoelectrochemical performance of natural extraction dyes have been studied in dye-sensitized solar cell devices. The results show the rather high conversion efficiency of 0.57%, 1.15%, 1.02%, 0.35% and 0.15% of each individual dye extraction, respectively.     

Photovoltaic and impedance properties of dye-sensitized solar cell based on nature dye from beetroot

The present study involves fabrication and photovoltaic characterization including impedance properties of dye-sensitized solar cells based on natural dye from beetroot. The electrode of the cell was prepared with commercial Fluorine-doped Tin Oxide glass with 100 μm layer of nanostructured TiO₂ whereas, the counter electrode consisted of platinum-coated glass. Fresh juice was extracted from beetroot to use as dye. The dye exhibited high absorption in visible range. Photovoltaic measurements of the solar cell gave a short circuit current density (Jsc) of 130 μA/cm² and an open-circuit voltage (VOC) of 0.38 V under AM 1.5 illumination intensity. The VOC and Jsc showed linear behavior at higher values of illumination intensities. The conductance-voltage, the capacitance-voltage and the series resistance voltage characteristics of the dye solar cell was measured at frequency range from 5 kHz to 5 MHz to study performance of the dye-sensitized solar cells with natural dyes.     

Fabrication and characterization of nanocrystalline n-CdO/p-Si as a solar cell

A nanocrystalline CdO/Si solar cell was fabricated via deposition of a CdO thin film on p-type silicon substrate with approximately 370 nm thickness using solid–vapor deposition for Cd powder at 1274 K with argon and oxygen flow. Scanning electron microscopy revealed that the product was a Cadmium oxide nanocrystalline. X-ray diffraction and energy dispersive X-ray analysis were used to characterize the structural properties of the solar cell. The nanocrystalline thin film had a grain size of 38 nm. The solar cell yielded a minimum effective reflectance that exhibited excellent light-trapping at wavelengths ranging from 400 to 1000 nm. Photoluminescence spectroscopy was conducted to investigate the optical properties. The direct band gap energy of the nanocrystalline CdO thin film was 2.46 eV. CdO/Si solar cell photovoltaic properties were examined under 100 mW/cm² solar radiation. The cell showed an open circuit voltage (V_oc) of 457 mV, a short-circuit current density (J_sc) of 18.5 mA/cm², a fill factor (FF) of 0.652, and a conversion efficiency (η) of 5.51%.     

Cu_2O/ZnO氧化物异质结太阳电池的研究进展

介绍了近年来低成本Cu_2O/ZnO氧化物异质结太阳电池方面的研究进展.应用于光伏器件的吸收层材料Cu_2O是直接带隙半导体材料,天然呈现p型;其原材料丰富,且对环境友好.Cu_2O/ZnO异质结太阳电池结构主要有平面结构和纳米线/纳米棒结构.纳米结构的Cu_2O太阳电池提高了器件的电荷收集作用;通过热氧化Cu片技术获得的具有大晶粒尺寸平面结构Cu_2O吸收层在Cu_2O/ZnO太阳电池应用中展现出了高质量特性.界面缓冲层(如i-ZnO,a-ZTO,Ga_2O_3等)和背表面电场(如p~+-Cu_2O层等)可有效地提高界面处能级匹配和增强载流子输运.10 nm厚度的Ga_2O_3提供了近理想的导带失配,减少了界面复合;Ga_2O_3非常适合作为界面层,其能够有效地提高Cu_2O基太阳电池的开路电压V_(oc)(可达到1.2 V)和光电转换效率.p~+-Cu_2O(如Cu_2O:N和Cu_2O:Na)能够减少器件中背接触电阻和形成电子反射的背表面电场(抑制电子在界面处复合).利用p型Na掺杂Cu_2O(Cu_2O:Na)作为吸收层和Zn_(1-x)Ge_x-O作为n型缓冲层,Cu_2O异质结太阳电池(器件结构:MgF_2/ZnO:Al/Zn_(0.38)Ge_(0.62)-O/Cu_2O:Na)光电转换效率达8.1%.氧化物异质结太阳电池在光伏领域展现出极大的发展潜力.     

Electrical and dielectric characterization of Au/ZnO/n-Si device depending frequency and voltage

Au/Zn O/n-type Si device is obtained using atomic layer deposition(ALD) for Zn O layer, and some main electrical parameters are investigated, such as surface/interface state(Nss), barrier height(Φb), series resistance(Rs), donor concentration(Nd), and dielectric characterization depending on frequency or voltage. These parameters are acquired by use of impedance spectroscopy measurements at frequencies ranging from 10 k Hz to 1 MHz and the direct current(DC) bias voltages in a range from-2 V to +2 V at room temperature are used. The main electrical parameters and dielectric parameters,such as dielectric constant(ε"), dielectric loss(ε"), loss tangent(tan δ), the real and imaginary parts of electric modulus(M and M), and alternating current(AC) electrical conductivity(σ) are affected by changing voltage and frequency. The characterizations show that some main electrical parameters usually decrease with increasing frequency because charge carriers at surface states have not enough time to fallow an external AC signal at high frequencies, and all dielectric parameters strongly depend on the voltage and frequency especially in the depletion and accumulation regions. Consequently, it can be concluded that interfacial polarization and interface charges can easily follow AC signal at low frequencies.     

Evaluation of electrical and optical characteristics of ZnO/CdS/CIS thin film solar cell

In this study, device modeling and simulation are conducted to explain the effects of each layer thickness and temperature on the performance of ZnO/CdS/CIS thin film solar cells. Also, the thicknesses of the CIS and CdS absorber layers are considered in this work theoretically and experimentally. The calculations of solar cell performances are based on the solutions of the well-known three coupling equations: the continuity equation for holes and electrons and the Poisson equation. Our simulated results show that the efficiency increases by reducing the CdS thickness. Increasing the CIS thickness can increase the efficiency but it needs more materials. The efficiency is more than 19% for a CIS layer with a thickness of 2 μm. CIS nanoparticles are prepared via the polyol route and purified through centrifugation and precipitation processes.Then nanoparticles are dispersed to obtain stable inks that could be directly used for thin-film deposition via spin coating.We also obtain x-ray diffraction(XRD) peak intensities and absorption spectra for CIS experimentally. Finally, absorption spectra for the CdS window layer in several deposition times are investigated experimentally.