光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法，在D形内包层掺Yb3+双包层光纤一端直接写制出Bragg光栅，用作双包层光纤激光器的输出腔镜.试验得到了线宽为0.196nm，波长为1058.2nm，最高输出功率为570mW的稳定激光输出，解决了激光器中模式竞争造成的输出不稳定现象.从速率方程出发，对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析，结果与实验符合很好. 关键词： 双包层光纤光栅 掺Yb3＋双包层光纤激光器 相位掩模 速率方程     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

Threshold characteristics of linear cavity Yb-doped double-clad fiber laser

The threshold characteristics of linear cavity Yb³⁺-doped double-clad fiber laser have been studied theoretically and experimentally. By solving rate equations, the expression for threshold pump power is obtained. The effects of fiber length, mirror reflectivity, pump wavelength, laser wavelength and Yb³⁺ concentration on threshold pump power are discussed. Then, the Yb³⁺-doped double-clad fiber laser with linear cavity is developed. By using various output couplers, threshold pump power has been measured. The experimental results are in accord with theory.     

Tunable double-clad ytterbium-doped fiber laser based on a double-pass Mach-Zehnder interferometer

We have demonstrated an adjustable double-clad Yb³⁺-doped fiber laser using a double-pass Mach-Zehnder interferometer. The laser is adjustable over a range of 40 nm from 1064 nm to 1104 nm. By adjusting the state of the polarization controller, which is placed in the double-pass Mach-Zehnder interferometer, we obtained central lasing wavelengths that can be accurately tuned with controllable spacing between different tunable wavelengths. The laser has a side mode suppression ratio of 42 dB, the 3 dB spectral width is less than 0.2 nm, and the slope efficiencies at 1068 nm, 1082 nm and 1098 nm are 23%, 32% and 26%, respectively. In addition, we have experimentally observed tunable multi-wavelengths lasing output.     

Output dynamics and stabilisation of a multi-mode double-clad Yb-doped silica fibre laser

The intensity dynamics of the double-clad Yb fibre laser have been characterised. Stabilisation of the fibre laser intensity by using uniform bi-directional pumping is demonstrated. For the single-end-pumped Yb fibre laser, the output becomes more stable for the shorter fibre length due to the higher threshold of stimulated Brillouin scattering, SBS, and Kerr effects and the reduction of saturated absorber effects caused by any unpumped fibre section. By additional pumping in a double-end-pumped configuration, the output power can be scaled higher before detecting high intensity pulses initiated by SBS in the Yb fibre laser due to the reduction of saturable absorption effect. It is confirmed that uniform pumping enhances the stability of the laser output.     

Three-dimensional simulation of the temperature field in high-power double-clad fiber laser

The 3D temperature distribution in high-power double-clad fiber laser (DCFL) and the evolution of the temperature field in the fiber are analyzed, according to the transient heat conduction equation. The temperature in the fiber reaches the maximum after opening the pump light about 20 s, and cools down to the room temperature after shutting down for also about 20 s. The shape of the inner-clad can only affect the spacial distribution of the temperature outside of the core, but have no effect on the maximum temperature in the core.     

Comparison of Yb-doped fiber laser with one-end and double-end pumping configuration

A high-power Ytterbium-doped fiber laser (YDFL) with homemade double clad fiber (DCF) is introduced in this paper. The output power characteristics of a linear cavity fiber laser have been studied theoretically by solving the rate equations and experimentally tested with single- and double-end-pumping configurations. When both ends of the fiber are pumped by two high-power laser diodes with a launched power of 300 W each, a maximum CW output of 444 W is obtained with a slope efficiency of 75%.     

基于体光栅的被动锁模可调谐线型腔掺镱光纤激光器

搭建了基于反射型体光栅和半导体可饱和吸收镜的线型腔全正色散掺镱光纤激光器,室温下实现了稳定的波长可连续调谐的连续被动锁模脉冲输出.重复频率16.42 MHz,锁模脉冲中心波长1030 nm时,脉冲光潜带宽0.32 nm,最大平均输出功率10.2 mW,单脉冲能量0.63 nJ.转动体光栅角度,利用其分光谱和选波长的特性,可使锁模脉冲的中心波长在约1011.9一1050.6 nm的范围内调谐,调谐范围约38.7 nm.实验中亦可观察到调Q锁模、二次谐波锁模、双波长和三波长输出现象.输出单波长锁模脉冲时,由于其波长可调谐的特性,该激光器可用作波分复用/光时分复用通信系统的光源和光学相干层析的调谐光源.     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb3+)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

 利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb³⁺)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

An approximate analytic solution of strongly pumped Yb-doped double-clad fiber lasers without neglecting the scattering loss

A theoretical analysis of strongly pumped Yb-doped double-clad fiber lasers is presented and an approximate analytic function of distributed laser along the whole fiber with the scattering loss is obtained for the first time. A comparison is made between the analytic solution and the exact numerical solution. The results have shown that the analytic function of distributed laser within the fiber is accurate and explicit. With the analytic solution the losses caused by laser scattering are shown in three different pump modes. The results verify that the backward pumping can get the highest output power in strongly pumped fiber lasers.     

Oscillation wavelength of fiber Bragg grating semiconductor lasers

Based on the physical fact that a laser containing a gain medium with homogenous line broadening oscillates at the wavelength which requires the smallest threshold gain due to the mode competition effect, after taking into account the wavelength-depended reflectivity distribution profile of a fiber Bragg grating, the oscillation wavelength λ_l of fiber Bragg grating semiconductor lasers has been investigated theoretically. The results show that the laser oscillation wavelength λ_B is not fixed at the Bragg reflection wavelength λ_l of fiber Bragg grating, and the offset between λ_B and λ_l depends on the reflectivity distribution profile of fiber Bragg grating and the gain profile of semiconductor gain medium.     

Simplified analytic solutions and a novel fast algorithm for Yb-doped double-clad fiber lasers

In this paper, continuous wave Yb³⁺-doped double-clad fiber lasers (DCFLs) with linear-cavity are investigated theoretically and numerically using the rate equations. Under the steady state conditions, the simplified analytic solutions of Yb³⁺-doped DCFLs under considering the scattering loss are deduced in the strongly pump condition. Compared with the known analytic solutions in published literatures, our analytic solutions are more accurate, especially, at higher reflectivity of output mirror. In addition, a fast and stable algorithm based on the Newton-Raphson method is proposed to simulate numerically Yb³⁺-doped DCFLs. The results by simplified analytic solutions are in good agreement with those by the numerical simulation. Moreover, we have performed the optimization of an Yb³⁺-doped DCFL using the simplified analytic solutions and the numerical simulations, respectively.     

Construction of a side pumped double-clad fiber using polished couplers

The paper presents a new way of side pumping double-clad fibers. Elaborated asymmetric polished couplers are presented. By using these couplers in pumping power set-ups of double-clad fiber very good pumping efficiency a very good efficiency was attained. The experimental and numerical optimizations of designed couplers are presented.     

Tunable dual-wavelength fiber laser based on a single fiber Bragg grating in a Sagnac loop interferometer

We propose a simple dual-wavelength Er-doped fiber laser configuration based on a dual-wavelength fiber Bragg grating written on the splice joint between two different fibers for wavelength-selective filter in the Sagnac loop interferometer. The wavelength separation between the adjacent lasing wavelengths is 1.12 nm and the side-mode suppression ratio (SMSR) is over 55 dB. The output power variation is less than 0.8 dB over a two-minute period. Moreover, the lasing wavelength can be effectively tuned using the thermal heating method.     

掺Yb3+双包层光纤激光器的数值分析

 对掺Yb³⁺双包层光纤激光器不同参数情况下的输出功率和增益分布进行了数值模拟，分析了一端泵浦和双端泵浦方式下输出特性的差异，激光沿光纤长度方向的分布，输出功率与光纤长度、腔镜反射率及泵浦功率的关系。结果显示：两端泵浦较一端泵浦增益更加平坦，输出功率也稍高；当泵浦光波长为975nm时，输出激光功率对光纤长度更为敏感，最佳光纤长度相对于泵浦光波长为915nm时短且转化效率高；在大功率长光纤的情况下，光纤有损耗时输出功率随输出腔镜反射率的增加单调地减小，无损耗时输出功率不随输出腔镜反射率变化。     

基于线型腔掺铒光纤激光器的光纤光栅传感实验研究

提出了一种基于线型腔掺铒光纤激光器的光纤布拉格光栅传感解调系统,并进行了理论分析和实验验证。此传感系统具有稳定性好、信噪比高、结构简单等特点。实验结果表明:在常温下光纤光栅传感解调系统能很好的实现光纤光栅传感信号的传感和检测;15m掺铒光纤用作增益介质可以产生较大信噪比的稳定激光输出,系统在4nm范围内的解调精度为0.04nm。     

Self-pulsing characteristics of a high-power single transverse mode Yb-doped CW fiber laser

We present an experimental study of self-pulsing characteristics of a high-power single transverse mode Yb-doped double-clad continuous wave (CW) fiber laser. The self-pulsing features under high-power single-end pumping and double-end pumping configurations have been shown to be distinct. Our experimental observation indicates that in single-end pumping configuration, self-pulsing is predominant due to saturable absorption effect, caused by the weakly pumped portion of the fiber at the farther end. However, in double-end pumping configuration, uniform pumping and hence gain uniformity along the fiber length avoids the onset of saturable absorption of signal along the fiber length and thereby reduces self-pulsing, which finally results in a much more stable output.     

Erbium-doped fiber ring laser sensor for high temperature measurements based on a regenerated fiber Bragg grating

This article presents an erbium-doped fiber ring laser for high temperature measurement with high accuracy. The proposed laser sensor employs a regenerated fiber Bragg grating (RFBG) as a sensor element. Through thermal treatments, the RFBG with enhanced thermal resistance was obtained. The laser emission optical spectrum presents good performance with a high optical signal-to-noise ratio of 58dB. Experimental results demonstrate a wavelength sensitivity to the temperature is 15.5 pm/ºC with the temperature range from 300ºC to 900ºC, and the correlation coefficient is 0.999. The results prove it is able to provide potential applications in high temperature measurement.     

基于色散补偿光纤的高速光纤光栅解调方法

本文提出并论证了一种光纤光栅高速解调的新方法, 利用色散补偿光纤的色散效应, 将光纤光栅的波长漂移信息转换成时域信息. 采用脉冲激光器作为光源, 仅需一个光脉冲可获取单根光纤上所有光纤光栅的反射光脉冲, 再根据各个光栅反射回光脉冲的延时变化即可实现波长的解调. 本方法可用于准分布光纤光栅传感网络解调, 系统采用全光纤结构, 无需波长扫描, 大大提高了解调速度. 本文搭建了测试系统进行实验验证, 对3个光纤光栅组成的准分布式传感网络进行了解调, 实验结果表明, 解调出的光纤光栅布喇格波长线性度好, 解调速度最高可达1 MHz, 采样数据取10次平均后解调线性度可达0.9969, 解调误差约为27.8 pm.