High frequency fiber laser emission generated by pump spiking

A stable and short pulse train of ∼100 MHz repetition frequency was obtained from an erbium doped fiber laser excited by a “continuous” semiconductor laser and by using a linear cavity defined by a Bragg grating pair. The operation frequency of the fiber laser was greater (∼5-15 times) than the cavity round-trip frequency. Emission properties obtained from the erbium doped fiber laser were correlated with those taken from the pump laser, which presented a particular optical noise (very short pulses) added to the continuous emission. From the temporal and radio-frequency analysis of both systems, we conclude that the pump emission characteristics are the responsible of the fiber laser pulsed behaviour.     

Thermal effects investigation and cavity design in passively mode-locked Nd:YVO4 laser with a SESAM

A diode-pumped passively mode-locked Nd:YVO₄ laser with a five-mirror folded cavity is presented by using a semiconductor saturable absorber mirror (SESAM). The temperature distribution and thermal lensing in laser medium are numerically analyzed to design a special cavity which can keep the power density on SESAM under its damage threshold. Both the Q-switched and continuous-wave mode-locked operation are experimentally realized. The maximum average output power of 8.94 W with a 9.3 ps pulse width at a repetition rate of 111 MHz is obtained under a pump power of 24 W, correspondingly the optical slope efficiency is 39.2%.     

SOA-based actively mode-locked fiber ring laser by forward injecting an external pulse train

An actively mode-locked fiber ring laser based on cross-gain modulation (XGM) in a semiconductor optical amplifier (SOA) is demonstrated to operate stably with a simple configuration. By forward injecting an easily-generated external pulse train, the mode-locked fiber laser can generate an optical-pulse sequence with pulsewidth about 6 ps and average output power about 7.9 mW. The output pulses show an ultra-low RMS jitter about 70.7 fs measured by a RF spectrum analyzer. The use of the proposed forward-injection configuration can realize the repetition-rate tunability from 1 to 15 GHz for the generated optical-pulse sequences. By employing a wavelength-tunable optical band-pass filter in the laser cavity, the operation wavelength of the designed SOA-based actively mode-locked fiber laser can be tuned continuously in a wide span between 1528 and 1565 nm. The parameters of external-injection optical pulses are studied experimentally to optimize the mode-locked fiber laser.     

All-fiber actively Q-switched Yb-doped laser

An all-fiber actively Q-switched Yb-doped laser is presented. Q-switching is performed by modulating a fiber Bragg grating via a magnetostrictive rod which is fixed to the fiber at the position of the grating. By exposing the rod to a changing magnetic field, the rod is stretched and relaxed causing the Bragg wavelength of the grating to shift and thereby changes the Q-factor of the cavity. Using Yb-doped fiber, pulses at 1052 nm are obtained at repetition rates from 1 to 200 kHz. At 75 kHz, 0.5 μJ pulses with peak powers of 3 W can be produced when 180 mW of pump power is applied. To the knowledge of the authors, this is the first all-fiber actively Q-switched Yb-doped laser presented to date.     

Radio-frequency interrogation of a fiber Bragg grating sensor in the configuration of a fiber laser with external cavities

A fiber laser sensor, which consists of two coupled cavities based on three fiber Bragg gratings (two of them acting as sensing elements) and is interrogated via the longitudinal mode beating frequency, is presented. The two resonant cavities have lengths of 4250 m and 4297 m, respectively. Their beating frequency is of the order of 24 kHz, and its shift as a function of the variation of the period of one (or both) of the sensing gratings, induced by strain or temperature changes, can be measured by a radio-frequency analyzer. The system is suitable for long-distance sensing with high spatial resolution and high sensitivity.     

Incorporate, switchable dual-wavelength fiber laser with Bragg gratings written in a polarization-maintaining erbium-doped fiber

A stable, incorporate and switchable dual-wavelength fiber laser with two fiber Bragg gratings written in a photosensitive and polarization-maintaining erbium-doped fiber directly, that is, without splices in the laser cavity, is proposed and demonstrated. Simultaneous dual-wavelength oscillation is achieved at room temperature with a wavelength spacing of 0.343 nm. The power fluctuation and wavelength shift of single-wavelength oscillations are measured to be less than 0.24 dB and 0.013 nm over 2 h. The wavelength switchability between single- and dual-wavelength oscillations is realized by altering the voltage upon the electrostrictive ceramic actuator.     

增益调制高重频脉冲光纤激光器实验研究

采用脉冲泵浦方案,研制出了基于增益调制技术的全光纤结构高重频脉冲激光器。采用电路直接调制的激光二极管作为泵浦源,双包层光纤作为增益介质,构造了光纤光栅选模的线形腔结构。实验中通过调整泵浦光脉冲宽度和光纤激光器谐振腔长度,得到了稳定的高重频脉冲。在100kHz重复频率下,采用21W的峰值泵浦功率和2.5μs的泵浦脉冲宽度,获得了1.06μm波长,脉冲宽度247ns的稳定脉冲激光输出。脉冲峰值功率一致性好,平均功率长期功率稳定性为2%。观察并分析了由于纵模拍频在脉冲包络上产生的次脉冲特性。通过一级放大实现89.6 W输出。     

Passive Q-switching of short-length Tm-doped silica fiber lasers by polycrystalline Cr:ZnSe microchips

We demonstrate passive Q-switching of short-length double-clad Tm³⁺-doped silica fiber lasers near 2 μm pumped by a laser diode array (LDA) at 790 nm. Polycrystalline Cr²⁺:ZnSe microchips with thickness from 0.3 to 1 mm are adopted as the Q-switching elements. Pulse duration of 120 ns, pulse energy over 14 μJ and repetition rate of 53 kHz are obtained from a 5-cm long fiber laser. As high as 530 kHz repetition rate is achieved from a 50-cm long fiber laser at ∼10-W pump power. The performance of the Q-switched fiber lasers as a function of fiber length is also analyzed.     

532 nm laser based on V-type doubly resonant intra-cavity frequency-doubling

LD side-pumped dual interconnected V-type quasi-continuous wave green laser has been demonstrated. The two Nd:YAG modules were placed in a plane-concave V-type resonator and a plane-concave straight cavity formed two stable operation beam of the 1064-nm fundamental frequency laser. Through acousto-optic Q-switched and frequency doubling crystal, two double-frequency laser beams arrived at the folded flat mirror, which were unidirectional output by the folded flat mirror at the end. As the pumped current was 50 A, the 532 nm green laser maximum average output power of 206 W at a repetition of 22.4 kHz was achieved with a pulse width of 201 ns and the largest single pulse energy of 9.2 mJ, corresponding to a peak power of 45.8 kW and a double frequency efficiency of 60.2%.     

Short pulse passively Q-switched Nd:GdYVO4 laser using a GaAs mirror

We report on a diode pumped passively Q-switched Nd:Gd_0.64Y_0.36VO₄ laser with a Cr⁴⁺:YAG saturable absorber. We show experimentally that by using an appropriately coated GaAs wafer as output coupler, the Q-switched pulse width can be significantly suppressed. Stable Q-switched pulse train with pulse width of 2.2 ns, peak power of 26.3 kW, repetition rate of 15.38 kHz have been obtained under an absorbed pump power of 8.54 W. The physical mechanism of pulse width narrowing by the GaAs wafer was also experimentally investigated.     

Tunable microwave photonic notch filter using a dual-wavelength fiber laser with phase modulation

A novel tunable microwave photonic notch filter using a phase-modulated dual-wavelength fiber laser is presented. A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. It is found that a stable room-temperature dual-wavelength operation can be achieved due to the presence of two reflection peaks arising from the orthogonal states of polarization (SOP) of the PM-FBG. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.36 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. The dual-wavelength fiber laser is combined with a phase modulator and a segment of single-mode fiber (SMF) as a dispersive device to form a tunable microwave photonic notch filter. By stretching the PM-FBG to tune the wavelength separation of the dual-wavelength fiber laser, a tunable microwave photonic notch filter with various free spectral ranges (FSRs) and a rejection ratio greater than 35 dB was developed.     

Switchable and tunable dual-wavelength ultrashort pulse generation in a passively mode-locked erbium-doped fiber ring laser

A simple switchable and tunable dual-wavelength passively mode-locked erbium-doped fiber ring laser based on nonlinear polarization rotation (NPR) effect is proposed and experimentally demonstrated. The NPR effect effectively induces wavelength- and intensity-dependent loss to readily implement stable dual-wavelength passively mode-locked operation. The wavelength switching and tuning of the dual-wavelength ultrashort pulse laser are achieved only by appropriately rotating the polarization controllers. The side-mode suppression ratio of the output pulse is larger than 41 dB over a wavelength-tuning range of 43.4 nm. Moreover, triple-wavelength ultrashort pulse can also be observed.     

Generation of dual wavelength ultrashort pulse outputs from a passive mode locked fiber ring laser

By incorporating two sections of polarization maintaining fibers in the passive mode locked fiber ring laser cavity, dual wavelength ultrashort pulse outputs, around 1558 nm and 1570 nm, having the same direction of polarization and pulse widths of 2.4 ps and 2.1 ps, respectively, were observed simultaneously.     

Self-Q-switching and mode-locking in an all-fiber Er/Yb co-doped fiber ring laser

Using a section of un-pumped Er/Yb co-doped fiber (EYDF) as a saturable absorber, Self-Q-switching and self-mode-locking pulses have been obtained in an all-fiber EYDF ring laser. Such laser is with the self-Q-switched pulse threshold of 135.22 mW, the repetition rate of approximately 22.2 kHz, and the pulse duration of ∼2.8 μs, respectively. The self-mode-locked threshold is 591.8 mW. By incorporating the saturable absorption in an un-pumped EYDF and a Mach-Zehnder interferometer, when the pump power is increased to 1242.9 mW, the continuous-wave (CW) mode-locking with the pulse width of 26 ns has also been demonstrated experimentally for the first time.     

Reflective carbon nanotube as the saturable absorber for mode-locked 1064 nm laser

With a reflective single-walled carbon nanotube as the saturable absorber, a laser diode-pumped passively mode-locked Nd:YVO₄ laser at 1064 nm was realized for the first time. The pulse duration of 12 ps was produced with a repetition rate of 83.7 MHz. The peak power and the single pulse energy of the mode-locking laser were 1.28 kW and 15.4 nJ, respectively.     

Environmentally stable ytterbium figure-of-eight fiber laser producing 177-fs pulses

Pulses of 177 fs and 1035 nm, with average power of 1.2 mW, have been generated directly from a passively mode-locked Yb-doped figure-of-eight fiber laser, with a nonlinear optical loop mirror for mode-locking and pairs of diffraction gratings for intracavity dispersion compensation. To our knowledge, these are the shortest pulses ever to come from a passively mode-locked Yb-doped figure-of-eight fiber laser. This represents a 5-fold reduction in pulse duration compared with that of previously reported passively mode-locked Yb-doped figure-of-eight fiber lasers. Stable pulse trains are produced at the fundamental repetition rate of the resonator, 24.0 MHz.     

Passively Q-switched Nd:YAG pumped UV lasers at 280 and 374 nm

Pulsed UV lasers at the wavelengths of 374 and 280 nm are realized by cascaded second harmonic generation (SHG) and sum frequency generation (SFG) processes using a Nd:YAG laser at 1123 nm. The Nd:YAG laser is longitudinally pumped and passively Q-switched, and it has a high peak power of 3.2 kW. The UV peak powers at 280 and 374 nm are 100 and 310 W, with pulse lengths of 6 and 8 ns, respectively. Spectral broadening of 374 nm laser by stimulated Raman scattering is studied in single mode pure silica core UV fiber. Realizations of UV lasers enabling compact design at 280 and 374 nm wavelengths are demonstrated.     

Offset frequency locking for nanosecond laser pulses

A method of multi-pulse discriminating frequency and high probability average value filtering is presented for offset frequency locking with ns laser pulses. In the experiment, the frequency locking for cavity-dumped CO₂ laser with 100 ns pulse width and the repetition rate of 10 kHz was studied. The precision was up to ±2 MHz at the heterodyne frequency 90 MHz. However, it is more than ±10 MHz for the single pulse discriminating frequency. This method can also be applied to laser offset frequency locking for many kinds of short pulse lasers.     

All-optical square-pulse generation and multiplication at 1.5 mum by use of a novel class of fiber Bragg gratings

A new class of linearly chirped fiber Bragg gratings, suitable for all-fiber optical multiplication and reshaping of picosecond pulse trains, is proposed and experimentally demonstrated. Repetition-rate multiplication, based on the temporal Talbot effect, is achieved by accurate control of the grating chirp, and a suitable design of the index-modulation depth profile allows for simultaneous square-pulse shaping. A 50-ps squarelike optical pulse train at 10-GHz repetition rate is obtained, starting from a 2.5-GHz Gaussian pulse train emitted by a mode-locked Er-Yb laser.     

Experimental investigation of self-starting operation in a F8L based on a symmetrical NOLM

We experimentally analyze the self-starting operation of a figure-eight mode-locked fiber laser. The design is based on a power-balanced nonlinear optical loop mirror (NOLM) with highly twisted low-birefringence fiber and a quarter-wave (QW) retarder in the loop. The NOLM operates by nonlinear polarization rotation. Self-starting mode-locking requires a careful adjustment of the NOLM low-power transmission, which is easily realized with our setup by adjusting the angle of the QW retarder. The laser is capable of generating ∼20 ps pulses at the fundamental repetition frequency of 0.78 MHz.