Feedback method of the noise suppression in wave-mixing amplifiers based on non-linear materials with photorefractive response in a reflection grating configuration

In the photorefractive wave-mixing system, fluctuation in the signal beam intensity of the photorefractive output with a reflection grating has been analyzed by employing pump feedback method. In this method, fluctuations of the photorefractive wave-mixing process not only induce the intensity fluctuation of the mixing waves but also induce phase fluctuation of the mixing waves. Thus, the phase of the pump and signal beams at the output surface fluctuates in time around a mean value. Using such a positive feedback method of a pump beams, the relative fluctuation in the photorefractive output signal beam intensity with respect to its mean intensity can be minimized significantly without reducing its mean intensity. The factors that control the fluctuation in the signal beam intensity, such as the phase fluctuation of the output pump beam, absorption strength of the material and the feedback reflectivity of the cavity mirrors, on the relative fluctuation of the output signal intensity in the photorefractive wave-mixing systems have been studied in detail. It has been found that the fluctuation of the output signal intensity relative to its mean intensity in the photorefractive wave-mixing system can be suppressed to larger extent by taking lower value of feedback reflectivity of the cavity mirrors which could exist at a higher value of absorption strength of the photorefractive materials.     

The statistical fluctuation of a single-mode laser system driven by coloured pump noise with signal modulation and the quantum noise with cross-correlation between its real and imaginary parts

Using the linear approximation method, this paper studies the statistical property of a single-mode laser driven by both coloured pump noise with signal modulation and the quantum noise with cross-correlation between its real and imaginary parts, and calculates the steady-state mean normalized intensity fluctuation and intensity correlation time. It analyses the influences of the modulation signal, the net gain coefficient, the noise and its correlation form on the statistical fluctuation of the laser system respectively. It is found that the coloured pump noise modulated by the signal has a great suppressing action on the statistical fluctuation of the laser system; the pump noise self-correlation time and the specific frequency of modulation signal have the result that the statistical fluctuation tends to zero. Furthermore, the `colour' correlation of pump noise has much influences on the statistical fluctuation of the laser system. Increasing the intensity of pump noise will augment the statistical fluctuation of the laser system, but the intensity of quantum noise and the coefficient of cross-correlation between its real and imaginary parts have less influence on the statistical fluctuation of the laser system. Therefore, from the conclusions of this paper the statistical property can be known and a theoretical basis for steady operation and output of the laser system can be provided.     

Influence of Signal and Noise on Statistical Fluctuation of Single-Mode Laser System

On the basis of calculating the steady-state mean normalized intensity fluctuation of a signal-mode laser system driven by both colored pump noise with signal modulation and the quantum noise with cross-correlation between its real and imaginary parts, we analyze the influence of modulation signal, noise, and its correlation form on the statistical fluctuation of the laser system. We have found that when the amplitude of modulation signal weakens and its frequency quickens, the statistical fluctuation will reduce rapidly. The statistical fluctuation of the laser system can be restrained by reducing the intensity of pump noise and quantum noise. Moreover, with prolonging of colored cross-correlation time, the statistical fluctuation of laser system experiences a repeated changing process, that is, from decreasing to augmenting,then to decreasing, and finally to augmenting again. With the decreasing of the value of cross-correlation coefficient, the statistical fluctuation will decrease too. When the cross-correlation form between the real part and imaginary part of quantum noise is zero correlation, the statistical fluctuation of laser system has a minimum. Compared with the influence of intensity of pump noise, the influence of intensity of quantum noise on the statistical fluctuation is smaller.     

Influence of Signal and Noise on Statistical Fluctuation of Single-Mode Laser System

On the basis of calculating the steady-state mean normalized intensity fluctuation of a signal-mode laser system driven by both colored pump noise with signal modulation and the quantum noise with cross-correlation between its real and imaginary parts, we analyze the influence of modulation signal, noise, and its correlation form on the statistical fluctuation of the laser system. We have found that when the amplitude of modulation signal weakens and its frequency quickens, the statistical fluctuation will reduce rapidly. The by reducing the intensity of pump noise and quantum noise. statistical fluctuation of the laser system can be restrained Moreover, with prolonging of colored cross-correlation time, the statistical fluctuation of laser system experiences a repeated changing process, that is, from decreasing to augmenting, then to decreasing, and finally to augmenting again. With the decreasing of the value of cross-correlation coe~cient, the statistical fluctuation will decrease too. When the cross-correlation form between the real part and imaginary part of quantum noise is zero correlation, the statistical fluctuation of laser system has a minimum. Compared with the influence of intensity of pump noise, the influence of intensity of quantum noise on the statistical fluctuation is smaller.     

考虑到束-波相互作用的速调管离子噪声二维模拟

采用粒子模拟的方法并考虑电子束与电磁波的相互作用，首次直接得到了速调管输出信号的离子噪声图像，阐述了束电子、二次电子、离子、电磁场之间的相互作用的动力学过程. 指出离子噪声所表现出来的相位波动是由电子束速度的波动引起的，电子束速度的变化来源于管内离子数量的变化，离子的数量的变化又与电子束状态变化相互影响，这是离子噪声产生的根本原因. 二次电子对离子噪声产生过程的影响甚微，但是其行为却反映了离子噪声的形成机理. 离子噪声引发的输出信号幅度波动取决于电子束速度和半径的改变，与离子行为密切相关. 关键词： 离子噪声 速调管 粒子模拟 电子束     

曲率波前传感器探测高斯光束时的信号误差

曲率波前传感器已被用于天文自适应光学和光学度量等领域。在这些领域使用时都假设入射波前光强均匀,但这种假设与曲率传感技术的基本原理不一致。利用傅里叶光学理论,给出了光强不均匀情况下曲率波前传感器的曲率信号解析式,并利用光强均匀和不均匀情况下的信号表达式对探测高斯光束时的信号误差进行了数值分析。结果表明：曲率波前传感器探测高斯光束时存在一定误差,相位分布为4阶Zernike多项式时,误差最大,且阶数越高,误差越小;分区平均曲率信号误差较小,一般在10％以下。     

光束偏转信号灵敏度的分析

激光光束编转法是一种非接触的探测技术。本文从理论上分析了光速偏转信号的灵敏度的基本限制。并给出了一种提高信号对光速偏转灵敏度的方法。     

激光光强扰动对相干场成像降质影响理论研究

激光相干场成像系统发射多束激光,经大气传输对远程目标成像,大气湍流引起的激光束光强扰动是影响成像质量的一个关键因素.本文从湍流引起的激光束光强扰动对回波解调信号的影响关系入手,建立了激光回波光强扰动因子对相位闭合系数和成像频谱分量的降质传函理论模型;基于三光束激光相干场成像系统仿真验证了理论模型的有效性.研究表明激光相干场成像频谱分量和成像像质主要受三光束相位闭合求解算法中第二光束光强扰动影响.该研究揭示了激光回波光强扰动对成像像质的影响机理,对于分析大气湍流等引起的光强扰动降质效应和合理分配多光束光强稳定性以提高成像质量具有理论指导意义.     

Talbot Images of Two-Dimensional Gaussian Beam Arrays with Amplitude Fluctuation

Talbot images constructed in the Fresnel diffraction region due to two-dimensional Gaussian beam arrays with amplitude fluctuation are statistically investigated using a mathematical model based on the propagation law of a Gaussian beam. The average intensity distribution of Talbot images is analyzed theoretically, and the corresponding simulation is conducted by computer. The relative fluctuation of the peak intensity to the mean with respect to Talbot images is found to be less than that of the source by approximately 1/4. Furthermore, the effect of the finite size of source arrays on the formation of Talbot images is revealed throughout the simulation as well as the effect of the amplitude fluctuation.     

First-Order-Like Phase Transition Induced by Two Different Kinds of Noise in Dispersive Optical Bistability

With unified colored noise approximation, the steady state distribution function in dispersive optical bistability including both intensity and phase fluctuations is obtained. The parameter plane of the first-order-like phase transition is a/so derived with numerical method. It is found that the number of extremes at non-zero values of the output field in the steady state distribution function is changed from zero, two to four. It is shown that the strengths of the intensity fluctuation and the phase fluctuation have great effect on the first-order-fike phase transition.     

具有质量及频率涨落的欠阻尼线性谐振子的随机共振

以往的研究大多考虑线性谐振子模型受频率涨落噪声的影响, 而当布朗粒子处于具有吸附能力的复杂环境时, 粒子质量也存在随机涨落. 因此, 本文研究具有质量及频率涨落两项噪声的二阶欠阻尼线性谐振子模型的随机共振现象. 利用Shapiro-Loginov公式和Laplace变换, 推导了系统响应一阶稳态矩及稳态响应振幅的解析表达式. 并根据稳态响应振幅的解析表达式, 建立了稳态响应振幅关于质量涨落噪声及频率涨落噪声各自的噪声强度能够诱导随机共振现象产生的充分必要条件. 仿真实验表明, 当系统参数满足本文所给出的充分必要条件要求时, 系统稳态响应振幅关于噪声强度的变化曲线具有明显的共振峰, 即此选定参数组合能够诱导系统产生随机共振现象.     

加速器束流诊断技术的新进展

介绍了加速器束流诊断技术的新进展, 包括束流位置测量技术、束团横向尺寸测量技术和束团长度测量技术. 束流位置测量技术主要介绍具有高位置分辨率的腔型束流位置检测器和数字束流位置处理技术. 束团尺寸测量技术主要介绍高空间分辨率的激光丝扫描器、光学渡越辐射和光学衍射辐射技术. 束团长度测量技术主要介绍高时间分辨率的相干辐射光谱技术、RF横向偏转腔、RF零相位技术和电光采样技术.     

偏置信号调制下噪声关联的周期调制对单模激光随机共振的影响

在噪声受偏置信号调制的情况下,讨论色噪声之间的关联受时间周期调制所驱动的单模激光系统中的随机共振.用线性化近似的方法计算了输出信噪比.具体讨论输出信噪比随噪声自关联时间、噪声强度和偏置信号的变化关系.发现输出信噪比随抽运噪声强度和自关联时间的变化出现随机共振,而偏置信号会降低随机共振的峰值.实际应用中应控制优选偏置信号强度. 关键词： 偏置信号 色噪声 时间周期调制 噪声间关联程度     

横向激发线偏振高斯光束的非傍轴传输

文章提出一种横向激发的任意线偏振高斯光束,该光束场量的模与传统的任意线偏振高斯光束具有相同的模,在源场区,其满足自由空间无源场的场方程。同时利用瑞利—索末菲衍射积分对该高斯光束的非傍轴传输特性进行了解析研究,给出了空间光强分布、束腰和远场发散角的解析通式,发现该类光束的远场光强呈一平顶空心光束。     

厄米-高斯光束在内含硬边光阑光学系统中的传输

把硬边光阑从复杂光学系统中“移”出来,即把任意一个含有硬边光阑的复杂光学系统体现到含有入射光瞳和出射光瞳的光学系统中，使硬边光阑的作用转化为出射光瞳的作用，以便求出观察面上的解析解。对入射面上的二维厄米 高斯光束，利用柯林斯公式和入射光瞳与出射光瞳的物像关系，可得到所要求观察面的场分布和解析结果，通过数值模拟验证了其正确性。通过分析计算得到如下结论：对于任意一个含有硬边光阑的复杂光学系统，都可以把光阑的作用从系统中“移”出来，把其看作是出射光瞳的作用，从而可以较为简便地求出观察面上的场分布。     

扩束准直光学系统中光学元件失调对高斯光束传输变换的影响分析

基于广义惠更斯-菲涅尔衍射积分公式, 以高斯光束为激光束模型,推导了激光光束通过失调扩束准直光学系统的传输公式,分析了光学元件失调对扩束准直光学系统输出光束传输特性的影响,并在此基础上进行了仿真。实验结果表明,高斯光束通过失调扩束准直光学系统时,出射光束变为偏心高斯光束,光学元件失调程度越大,输出光束越偏离光轴,光束质量越差。在同样的失调下,长焦距光学元件对输出光束影响更大,因此在激光扩束准直光学系统中,调整长焦距光学元件更为重要。     

湍流大气中激光聚焦光束后向散射的数值模拟

 对基于聚焦光束后向散射到达角起伏的湍流测量进行了数值模拟。通过近轴标量波动方程和分形相屏算法,提出了聚焦光束二次传输的数值模型,分别就固定点信标光源和聚焦光束后向散射的到达角起伏方差的统计特征进行了分析,并取得了很好的相关性,得出了可以从聚焦光束的回波图像信号里提取大气湍流信息的结论。讨论了聚焦距离对固定点光源和回波光束的到达角起伏方差相似度的影响。     

波片光轴偏差对偏振分光光束振幅和相位的影响研究

研究了在线偏振光入射、波片和偏振分束器结合使用时波片光轴偏差对偏振分束器分出的两束光的振幅和相位的影响。给出了在两种放置情况下,任意波片光轴方向偏差对偏振分光光束振幅和相位影响的表达式。详细分析了1/4波片和1/8波片的影响性质,给出了具体的振幅和相位影响关系式。     

梯度轴棱锥产生单个Bottle beam

首次提出一种新的梯度轴棱锥模型,这种梯度轴棱锥在传统的轴棱锥基础上,将轴棱锥顶点的锥角设计成具有一定的梯度.平面波入射到这种梯度轴棱锥,其衍射场会形成两个区域的Bessel光,并且在这两个Bessel光之间形成一个Bottle beam（局域空心光束）.由于Bottle beam具有三维封闭的空心区域和极高的强度梯度,可用作激光导管、光镊和光学扳手等,在生命科学和纳米科技中有重要应用.从几何光学角度分析了梯度轴棱锥形成单个Bottle beam的原理,由衍射及相干理论,分析和模拟了纵向剖面光强分布和横截面光强分布.研究结果对梯度轴棱锥的设计和应用具有指导意义. 关键词： 梯度轴棱锥 Bottle beam 轴棱锥 Bessel光     

Spectral characteristic of a pulsed hollow Gaussian beam passing through a circular aperture

The spectral characteristics of a pulsed hollow Gaussian beam passing through a circular aperture are studied. Based on the vectorial Rayleigh diffraction integrals, the analytical expressions of the spectra for the complex analytic signal representation and for the complex amplitude envelope representation are derived, respectively, and the comparison between them is made. The influences of the truncation parameter and the beam order on the spectral shifts and on the spectral switches are illustrated. It is shown that the spectrum for the complex analytic signal representation and that for the complex amplitude envelope representation are obvious different as the pulse shorter than an optical period.