A one-pot synthetic approach to prepare palladium nanoparticles embedded hierarchically porous TiO2 hollow spheres for hydrogen peroxide sensing

A simple one-step method to fabricate hierarchically porous TiO₂/Pd composite hollow spheres without any template was developed by using solvothermal treatment. Pd nanoparticles (2-5 nm) were well dispersed in the mesopores of the TiO₂ hollow spheres via in-situ reduction. In our experiment, polyvinylpyrrolidone played an important role in the synthetic process as the reducing agent and the connective material between TiO₂ and Pd nanoparticles. HF species generated from solvothermal reaction leaded to the formation of TiO₂ hollow spheres and Ostwald ripening was another main factor that affected the size and structure of the hollow spheres. The as-prepared TiO₂/Pd composite hollow spheres exhibited high electrocatalytic activity towards the reduction of H₂O₂. The sensitivity was about 226.72 μA mM⁻¹ cm⁻² with a detection limit of 3.81 μM at a signal-to-noise ratio of 3. These results made the hierarchically porous TiO₂/Pd composite a promising platform for fabricating new nonenzymic biosensors.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

A novel amperometric biosensor for the detection of nitrophenol

We report on a novel amperometric biosensor for detecting phenolic compounds based on the co-immobilization of horseradish-peroxidase (HRP) and methylene blue (MB) with chitosan on Au-modified TiO₂ nanotube arrays. The titania nanotube arrays were directly grown on a Ti substrate using anodic oxidation first; a gold thin film was then coated onto the TiO₂ nanotubes by an argon plasma technique. The morphology and composition of the fabricated Au-modified TiO₂ nanotube arrays were characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Cyclic voltammetry and amperometry were used to study the proposed electrochemical biosensor. The effect of pH, applied electrode potential and the concentration of H₂O₂ on the sensitivity of the biosensor have been systemically investigated. The performance of the proposed biosensor was tested using seven different phenolic compounds, showing very high sensitivity; in particular, the linearity of the biosensor for the detection of 3-nitrophenol was observed from 3 × 10⁻⁷ to 1.2 × 10⁻⁴ M with a detection limit of 9 × 10⁻⁸ M (based on the S/N = 3).     

Synthesis and photocatalytic applications of Ag/TiO2-nanotubes

TiO₂- and Ag/TiO₂-nanotubes (NTs) were synthesized by hydrothermal methods and microwave-assisted preparation, respectively. Scanning electron microscopy, high resolution transmission electron microscopy, Brunauer-Emmett-Teller particle surface area measurement and X-ray diffraction were used to characterize the nanotubes. Rutile TiO₂-NTs with Na₂Ti₅O₁₁ crystallinity had a length range of 200-400 nm and diameters of 10-20 nm. TiO₂- and Ag/TiO₂-NTs with a 0.4% deposition of Ag had high surface areas of 270 and 169 m² g⁻¹, respectively. The evaluation of photocatalytic activity showed that Ag/TiO₂-NTs displayed higher photocatalytic activity than pure TiO₂-NTs and a 60.91% degradation of Rhodamine-B with 0.8% deposition of Ag species. Also 60% of Rhodamine-6G was physisorbed and 40% chemisorbed on the surface of TiO₂-NTs. In addition, the photocatalytic degradations of organochlorine pesticides taking α-hexachlorobenzene (BHC) and dicofol as typical examples, were compared using Ag/TiO₂-NTs, and found that their degradations rates were all higher than those obtained from commercial TiO₂.     

Preparation and characterization of Zr doped TiO2 nanotube arrays on the titanium sheet and their enhanced photocatalytic activity

This paper described a new method for the preparation of Zr doped TiO₂ nanotube arrays by electrochemical method. TiO₂ nanotube arrays were prepared by anodization with titanium anode and platinum cathode. Afterwards, the formed TiO₂ nanotube arrays and Pt were used as cathode and anode, respectively, for preparation of Zr/TiO₂ nanotube arrays in the electrolyte of 0.1 M Zr(NO₃)₄ with different voltage and post-calcination process. The nanotube arrays were characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV-Vis diffusion reflection spectra (DRS). The photocatalytic activities of these nanotubes were investigated with Rhodamine B as the model pollutant and the results demonstrated that the photocatalytic efficiency of Zr doped TiO₂ nanotubes was much better than that of TiO₂ nanotubes under UV irradiation. Zr/TiO₂ nanotube arrays doped at 7 V and calcined at 600 °C (denoted as TiO₂-7 V-600) achieved the best photocatalytic efficiency and the most optimal doping ratio was 0.047 (Zr/Ti). TiO₂-7 V-600 could be reused for more than 20 times and maintained good photocatalytic activities.     

Mixed conductivity, structural and microstructural characterization of titania-doped yttria tetragonal zirconia polycrystalline/titania-doped yttria stabilized zirconia composite anode matrices

Taking advantage of the fact that TiO₂ additions to 8YSZ cause not only the formation of a titania-doped YSZ solid solution but also a titania-doped YTZP solid solution, composite materials based on both solutions were prepared by solid state reaction. In particular, additions of 15 mol% of TiO₂ give rise to composite materials constituted by 0.51 mol fraction titania-doped yttria tetragonal zirconia polycrystalline and 0.49 mol fraction titania-doped yttria stabilized zirconia (0.51TiYTZP/0.49TiYSZ). Furthermore, Y₂(Ti_1−yZr_y)₂O₇ pyrochlore is present as an impurity phase with y close to 1, according to FT-Raman results. Lower and higher additions of titania than that of 15 mol%, i.e., x=0, 5, 10, 20, 25 and 30 mol% were considered to study the evolution of 8YSZ phase as a function of the TiO₂ content. Furthermore, zirconium titanate phase (ZrTiO₄) is detected when the titania content is equal or higher than 20 mol% and this phase admits Y₂O₃ in solid solution according to FE-SEM-EDX.The 0.51TiYTZP/0.49TiYSZ duplex material was selected in this study to establish the mechanism of its electronic conduction under low oxygen partial pressures. In the pO₂ range from 0.21 to 10^−7.5 atm. the conductivity is predominantly ionic and constant over the range and its value is 0.01 S/cm. The ionic plus electronic conductivity is 0.02 S/cm at 1000 °C and 10^−12.3 atm. Furthermore, the onset of electronic conductivity under reducing conditions exhibits a −1/4 pO₂ dependence. Therefore, it is concluded that the n-type electronic conduction in the duplex material can be due to a small polaron-hopping between Ti³⁺ and Ti⁴⁺.     

Photoinduced interactions between colloidal TiO2 nanoparticles and calf thymus-DNA

The interaction of colloidal TiO₂ nanoparticles with calf thymus-DNA was studied by using absorption, FT-IR, steady state and time resolved fluorescence spectroscopic techniques. The apparent association constant has been deduced (K_app = 2.85 × 10³ M⁻¹) from the absorption spectral changes of the DNA-colloidal TiO₂ nanoparticles using the Benesi–Hildebrand equation. Addition of colloidal TiO₂ nanoparticles quenched the fluorescence of EtBr–DNA. The number of binding sites (n = 0.97) and the apparent binding constant (K = 6.68 × 10³ M⁻¹) were calculated from relevant fluorescence quenching data. The quenching, through a static mechanism, was confirmed by time resolved fluorescence spectroscopy.     

Preparation of photocatalytic nano-ZnO/TiO2 film and application for determination of chemical oxygen demand

A composite nano-ZnO/TiO₂ film as photocatalyst was fabricated with vacuum vaporized and sol-gel methods. The nano-ZnO/TiO₂ film improved the separate efficiency of the charge and extended the range of spectrum, which showed a higher efficiency of photocatalytic than the pure nano-TiO₂ and nano-ZnO film. The photocatalytic mechanism of nano-ZnO/TiO₂ film was discussed, too. A new method for determination of low chemical oxidation demand (COD) value in ground water based on nano-ZnO/TiO₂ film using the photocatalytic oxidation technology was founded. This method was originated from the direct determination of the Mn(VII) concentration change resulting from photocatalytic oxidation of organic compounds on the nano-ZnO/TiO₂ film, and the COD values were calculated from the absorbance of Mn(VII). Under the optimal operation conditions, the detection limit of 0.1 mg l⁻¹, COD values with the linear range of 0.3-10.0 mg l⁻¹ were achieved. The results were in good agreement with those from the conventional COD methods.     

Electrogenerated chemiluminescence of anatase TiO₂ nanotubes film

Highly ordered titanium dioxide (TiO₂) nanotubes film was successfully synthesized via anodic oxidation of a Ti foil in an ammonium fluoride-based ethylene glycol solution. The electrogenerated chemiluminescence (ECL) behavior of the resulting TiO₂ nanotubes film was subsequently studied. Strong ECL emission was observed at −1.40 V (vs. Ag/AgCl) and the ECL spectrum displayed three emission peaks which were bathochromatically shifted by ca. 140 nm as compared to its corresponding photoluminescence (PL) emission peaks, indicating that the surface state plays an important role in the emission process. The ECL emission can also occur in a deareated solution attributing to the surface adsorbed O₂ molecules. The ECL emission intensity was quenched by dopamine and greatly enhanced in the presence of dissolved O₂ and H₂O₂, making it possible to detect these analytes. The TiO₂ nanotubes film has been successfully applied to determine the dissolved O₂ content in river and pond water samples, the H₂O₂ concentration in commercial disinfectant samples and the dopamine concentration in commercial dopamine injections with satisfactory results. The plausible ECL mechanisms of TiO₂ nanotubes film in aqueous solution are discussed.     

Enhanced gas sensing by assembling Pd nanoparticles onto the surface of SnO2 nanowires

SnO₂ nanowires with an average 0.6 μm in length and about 25 nm in diameter were prepared by a hydrothermal method. The sensors were fabricated using SnO₂ nanowires assembled with Pd nanocrystals. The sensing properties of the sensors such as selectivity, response-recovery time and stability were tested at 290 °C. After assembling Pd nanocrystals onto the surface of SnO₂ nanowires, the gas sensing properties of the sensors toward H₂S were improved. The sensors based on Pd nanoparticle@SnO₂ nanowires exhibit high stability owing to stable single crystal structure. The mechanism of promoting sensing properties with Pd nanoparticles is discussed.     

Synthesis of visible-light reactive TiO2−xNy photocatalyst by mechanochemical doping

Yellowish TiO_2−xN_y was prepared by a novel mechanochemical nitrogen-doping method. The samples were prepared by a high-energy ball milling of P25 titania with different nitrogen sources such as hexamethylenetetramine, urea or ammonium carbonate, followed by calcination in air at 400 °C. The high mechanical energy accelerated the phase transformation of anatase to rutile, while the existence of the nitrogen reagents tended to block the transformation. The calcination treatment slightly increased the crystallinity of the prepared titania. The prepared powders possessed two absorption edges at around 400 and 540 nm and showed an excellent photocatalytic ability for the oxidation of nitrogen monoxide under visible light irradiation. Under the irradiation of visible light with wavelengths of >510 nm, nitrogen monoxide could be continuously removed by the nitrogen doped titania prepared from the P25 titania-hexamethylenetetramine mixture, while the powders prepared using urea and ammonium carbonate as nitrogen sources showed lower activities. This mechanochemical technique might be widely useful for doping oxides with nonmetallic elements.     

The catalytic role of oxide in the thermooxidative degradation of poly(methyl methacrylate)-TiO2 nanocomposites

The influence of TiO₂ nanoparticles on the thermal degradation of poly(methyl methacrylate) (PMMA) was investigated by TGA. The studied materials were characterized by Py-GC-MS, TEM, SEM, TGA, DSC and TGA-MS. The PMMA-TiO₂ nanocomposites were prepared by melt blending with different (5, 10, 15 and 20 wt% TiO₂) loadings. According to TGA results and to the activation energy (determined by the model-free isoconversional method of Vyazovkin), the incorporation of 5 wt% of TiO₂ nanoparticles into PMMA stabilizes it by more than 40 °C. However, for higher loading contents, a catalytic effect on the thermal decomposition was observed which increased with the oxide content. The results obtained by Py-GC-MS showed clearly that TiO₂ increases the formation of methanol, methacrylic acid and propanoic acid methyl ester during the degradation of PMMA. This catalytic effect could be explained through the interaction of the methoxy group of the methacrylate function with the hydroxyl groups present at the surface of the oxide particles.     

Raman investigations of SERS activity of Ag nanoclusters on a TiO2-nanotubes/Ti substrate

Tubular arrays of TiO₂ nanotubes (ranging in diameter from 40 to 110 nm) on a Ti substrate were used as a support for Ag deposits obtained by the sputter deposition technique where the amount of Ag varied from 0.01 to 0.2 mg Ag/cm². Those composite supports were intended for surface-enhanced Raman scattering (SERS) investigations. Composite samples of Ag/TiO₂ nanotube/Ti were studied with the aid of scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) to reveal their characteristic morphological and chemical features. Raman spectra of pyridine (as a probe molecule) were measured at different cathodic potentials ranging from −0.2 down to −1.2 V after the pyridine had been adsorbed on the Ag-covered TiO₂ nanotube/Ti substrates. In addition, SERS spectra on a bulk standard activated Ag substrate were also measured.The SERS activity of the composite samples was strongly dependent on the amount of Ag deposit. At and above 0.06 mg Ag/cm², the SERS signal was even higher than that for the Ag reference substrate. The high activity of the composites is mainly a result of their specific morphology. The high SERS sensitivity on the surface morphology made it possible to monitor very small temporal changes in the Ag clusters. This rearrangement was not detectable with microscopic (SEM) or microanalytical (AES) methods.     

Influence of High-energy electron-beam on photocatalytic activity of TiO2 films on carbon-fiber deposited by atomic layer deposition

High-energy electron-beam with energy of 1 MeV was used for modifying surface structure of TiO₂ thin films on carbon fiber prepared by using atomic layer deposition under atmospheric pressure. TiO₂ nanoparticles (∼20 nm) on carbon fiber underwent structural modification of the surface upon electron-beam treatment, resulting in enhanced photocatalytic activity. In contrast, a thicker film of TiO₂ did not show such changes in surface structure and photocatalytic activity by electron-beam treatment. We demonstrate that electron-beam can be used for modifying surface structure of photocatalysts consisting of nanoparticles for improvement of their activity.     

水热法合成掺杂铁离子的小管径TiO2纳米管

碳纳米管这种一维结构的新材料的发现为物理、化学、材料科学和纳米科学开辟了全新的研究领域.近年来,非碳无机类富勒烯(Inorganic Fullerenelike,简称IF)纳米管也受到人们的广泛关注.     

Dependence of nitrogen doping on TiO2 precursor annealed under NH3 flow

N-doped TiO₂ photocatalysts were prepared by annealing two different precursors, P25 and a TiO₂ xerogel powder under NH₃/Ar flow at 500, 550, and 600 °C. The xerogel powder prepared by peptizing Ti(OH)₄ with HNO₃ was composed of nanoparticles and had large specific surface area. During the annealing process, the xerogel powder underwent increase in crystallinity, grain growth and phase transformation, whereas P25 did not show obvious changes. Compared with the N-doped TiO₂ photocatalysts from P25, the N-doped TiO₂ photocatalysts from the xerogel powder possessed higher concentrations of the substitutional nitrogen and exhibited more obvious absorption in the visible light region. The N-doped TiO₂ photocatalysts from the xerogel powder exhibited obvious visible-light activities for photodegrading methylene blue and the sample prepared at 500 °C achieved the best performance with a rate constant (k) about 0.44 h⁻¹, whereas those from P25 did not exhibit improved visible-light activities.     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.     

Tris(2,2′-bipyridyl)ruthenium(II) electrogenerated chemiluminescence sensor based on carbon nantube dispersed in sol-gel-derived titania-Nafion composite films

A highly sensitive and stable tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) electrogenerated chemiluminescence (ECL) sensor was developed based on carbon nanotube (CNT) dispersed in mesoporous composite films of sol-gel titania and perfluorosulfonated ionomer (Nafion). Single-wall (SWCNT) and multi-wall carbon nanotubes (MWCNT) can be easily dispersed in the titania-Nafion composite solution. The hydrophobic CNT in the titania-Nafion composite films coated on a glassy carbon electrode certainly increased the amount of Ru(bpy)₃²⁺ immobilized in the ECL sensor by adsorption of Ru(bpy)₃²⁺ onto CNT surface, the electrocatalytic activity towards the oxidation of hydrophobic analytes, and the electronic conductivity of the composite films. Therefore, the present ECL sensor based on the CNT-titania-Nafion showed improved ECL sensitivity for tripropylamine (TPA) compared to the ECL sensors based on both titania-Nafion composite films without CNT and pure Nafion films. The present Ru(bpy)₃²⁺ ECL sensor based on the MWCNT-titania--Nafion composite gave a linear response (R² = 0.999) for TPA concentration from 50 nM to 1.0 mM with a remarkable detection limit (S/N = 3) of 10 nM while the ECL sensors based on titania-Nafion composite without MWCNT, pure Nafion films, and MWCNT-Nafion composite gave a detection limit of 0.1 μM, 1 μM, and 50 nM, respectively. The present ECL sensor showed outstanding long-term stability (no signal loss for 4 months).     

Preparation and properties of amorphous titania-coated zinc oxide nanoparticles

Amorphous TiO₂-coated ZnO nanoparticles were prepared by the solvothermal synthesis of ZnO nanoparticles in ethanol and the followed by sol-gel coating of TiO₂ nanolayer. The analyses of X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed that the resultant ZnO nanoparticles were hexagonal with a wurtzite structure and a mean diameter of about 60 nm. Also, after TiO₂ coating, the TEM images clearly indicated the darker ZnO nanoparticles being surrounded by the lighter amorphous TiO₂ layers. The zeta potential analysis revealed the pH dependence of zeta potentials for ZnO nanoparticles shifted completely to that for TiO₂ nanoparticles after TiO₂ coating, confirming the formation of core-shell structure and suggesting the coating of TiO₂ was achieved via the adhesion of the hydrolyzed species Ti-O⁻ to the positively charged surface of ZnO nanoparticles. Furthermore, the analyses of Fourier transform infrared (FTIR) and Raman spectra were also conducted to confirm that amorphous TiO₂ were indeed coated on the surface of ZnO nanoparticles. In addition, the analyses of ultraviolet-visible (UV-VIS) and photoluminescence (PL) spectra revealed that the absorbance of amorphous TiO₂-coated ZnO nanoparticles at 375 nm gradually decreased with an increase in the Ti/Zn molar ratio and the time for TiO₂ coating, and the emission intensity of ZnO cores could be significantly enhanced by the amorphous TiO₂ shell.     

Synthesis of titanate, TiO2 (B), and anatase TiO2 nanofibers from natural rutile sand

Titanate nanofibers were synthesized by hydrothermal method (150 °C for 72 h) using natural rutile sand as the starting materials. TiO₂ (B) and anatase TiO₂ (high crystallinity) nanofibers with the diameters of 20-100 nm and the lengths of 10-100 μm were obtained by calcined titanate nanofibers for 4 h at 400 and 700 °C (in air), respectively. The samples characterized by XRD, SEM, TEM, SAED, HRTEM, and BET surface area. This synthesis method provides a simple route to fabricate one-dimensional nanostructured TiO₂ from low cost material.