Photoluminescent BaMoO4 nanopowders prepared by complex polymerization method (CPM)

The BaMoO₄ nanopowders were prepared by the Complex Polymerization Method (CPM). The structure properties of the BaMoO₄ powders were characterized by FTIR transmittance spectra, X-ray diffraction (XRD), Raman spectra, photoluminescence spectra (PL) and high-resolution scanning electron microscopy (HR-SEM). The XRD, FTIR and Raman data showed that BaMoO₄ at 300 °C was disordered. At 400 °C and higher temperature, BaMoO₄ crystalline scheelite-type phases could be identified, without the presence of additional phases, according to the XRD, FTIR and Raman data. The calculated average crystallite sizes, calculated by XRD, around 40 nm, showed the tendency to increase with the temperature. The crystallite sizes, obtained by HR-SEM, were around of 40-50 nm. The sample that presented the highest intensity of the red emission band was the one heat treated at 400 °C for 2 h, and the sample that displayed the highest intensity of the green emission band was the one heat treated at 700 °C for 2 h. The CPM was shown to be a low cost route for the production of BaMoO₄ nanopowders, with the advantages of lower temperature, smaller time and reduced cost. The optical properties observed for BaMoO₄ nanopowders suggested that this material is a highly promising candidate for photoluminescent applications.     

A sol-gel route for the development of rare-earth aluminum borate nanopowders and transparent thin films

A new sol-gel route was applied to obtain Y_0.9Er_0.1Al₃(BO₃)₄ crystalline powders and amorphous thin films by using Al(acac)₃, B(OPrⁱ)₃, Y(NO₃)₃·6H₂O, and Er(NO₃)₃·5H₂O as starting materials dissolved in propionic acid and ethyl alcohol mixtures. Our study shows that propionic acid acts as good chelant agent for yttrium and erbium ions while ethyl alcohol allows to dissolve Al(acac)₃. This process makes the resulting sols very stable to obtain homogeneous gels and transparent amorphous thin films. In addition, the propionic acid prevents the sol precipitation, making easy porous- and crack-free thin film depositions. Chemical reactions involved in the complexation were discussed. As-prepared powders and films are amorphous and present a good thermal stability due to their high glass transition (746 °C) and crystallization temperatures (830 °C). This new sol-gel route showed to be adequate to obtain dense and crack-free thin films free of organic and hydroxyl groups that can be considered as promising materials to be used in integrated optical systems.     

Surface chemistry and optical property of TiO2 thin films treated by low-pressure plasma

The low temperature RF plasma treatment was used to control the surface chemistry and optical property of TiO₂ thin films deposited by RF magnetron sputtering with a very good uniformity at 300 °C substrate heating temperature. The XRD pattern indicates the crystalline structure of the film could be associated to amorphous structure of TiO₂ in thin film. The plasma treatment of TiO₂ film can increase the proportion of Ti³⁺ in Ti2p and decrease in carbon atoms as alcohol/ether group in C1s at the surface. The optical transmittance of the film was enhanced by 50% after the plasma treatment. The surface structure and morphology remain the same for untreated and low-pressure plasma-treated films. Therefore, increase in the optical transmission could be due to change in surface chemistry and surface cleaning by plasma treatment.     

Optical fiber evanescent wave absorption spectrometry of nanocrystalline tin oxide thin films for selective hydrogen sensing in high temperature gas samples

SnO₂ nanocrystalline material was prepared with a sol-gel process and thin films of the nanocrystalline SnO₂ were coated on the surface of bent optical fiber cores for gas sensing. The UV/vis absorption spectrometry of the porous SnO₂ coating on the surface of the bent optical fiber core exposed to reducing gases was investigated with a fiber optical spectrometric method. The SnO₂ film causes optical absorption signal in UV region with peak absorption wavelength at around 320 nm when contacting H₂-N₂ samples at high temperatures. This SnO₂ thin film does not respond to other reducing gases, such as CO, CH₄ and other hydrocarbons, at high temperatures within the tested temperature range from 300 °C to 800 °C. The response of the sensing probe is fast (within seconds). Replenishing of the oxygen in tin oxide was demonstrated by switching the gas flow from H₂-N₂ mixture to pure nitrogen and compressed air. It takes about 20 min for the absorption signal to decrease to the baseline after the gas sample was switched to pure nitrogen, while the absorption signal decreased quickly (in 5 min) to the baseline after switching to compressed air. The adhesion of tin oxide thin films is found to be improved by pre-coating a thin layer of silica gel on the optical fiber. Adhesion increases due to increase interaction of optical fiber surface and the coated silica gel and tin oxide film. Optical absorption spectra of SnO₂ coating doped with 5 wt% MoO₃ were observed to change and red-shifted from 320 nm to 600 nm. SnO₂ thin film promoted with 1 wt% Pt was found to be sensitive to CH₄ containing gas.     

Optimization of the photocatalytic activity of CdO + CdTiO3 coupled oxide thin films obtained by sol-gel technique

In the preparation of CdO + CdTiO₃ polycrystalline thin films by the sol-gel method, the optical, structural and crystalline properties, as well as the photocatalytic activity (PA) depends strongly on the sintering temperature (Ts) of the films and of the Ti/Cd ratio used in the precursor solution. In this work, CdO + CdTiO₃ thin films were prepared using a Ti/Cd constant ratio in the precursor solution. The films were sintered at six different Ts in the 450-550 °C range, in an open atmosphere. The structure of the films was characterized by X-ray diffraction and the PA was evaluated by the photobleaching of methylene blue in an aqueous solution using a UV-vis spectrometer. The relative intensity of the diffraction peaks associated with CdO and CdTiO₃, change with the Ts. The better photocatalytic activities were obtained for the films sintered at 490 °C and 550 °C. When the CdO was removed from the films by chemical etching the PA decreased, showing the importance of coupling both oxides.     

UV-Visible and IR Spectroelectrochemical Properties of V2O5 Crystalline Films Charged/Discharged in Extended Potential Range

Electrochemical properties of amorphous and crystalline V₂O₅ films, dip-coated from V-oxoisopropoxide sols and thermally treated at various temperatures (100, 150, 200 and 300°C), have been studied in extended potential range, i.e. from 1.4 to –1.6 V vs. Ag/AgCl in 1M LiClO₄/propylen carbonate (PC) electrolyte. The formation of various lithiated (-, -, - and -Li _x V₂O₅) phases was correlated with the values of insertion coefficient x obtained from cyclic voltammograms (CV) of crystalline V₂O₅ films (300°C). Reversible charging was observed when films were cycled up to –1.0 V vs. Ag/AgCl, while the extension of the potential to –1.3 V vs. Ag/AgCl change the CV of films irreversibly. Charging of crystalline V₂O₅ films was followed by the help of in-situ UV-visible spectroscopy, that revealed the intensity variations of the polaron absorption above 600 nm and the presence of the absorbing V³⁺ species between 550 and 650 nm. Ex-situ IR spectra of the crystalline films charged/discharged at –1.6V/1.4V vs. Ag/AgCl confirmed the amorphisation of the films' structure.     

Microstructure and luminescence of transparent glass ceramic containing Er:BaF2 nano-crystals

Transparent BaF₂-SiO₂ glass ceramics doped with different content of Er³⁺ were prepared by sol-gel method. The microstructural evolution of the samples was studied with X-ray diffraction (XRD), transmission electron microscope (TEM), absorption and infrared spectra (IR). BaF₂ nano-crystals with 2-15 nm in size, depending on the crystallization temperature, distributed homogeneously among the amorphous silica matrix. The BaF₂ lattice parameters decreased with the increasing of Er³⁺ doping, indicating the incorporation of Er³⁺ into nano-crystals, which was further confirmed by energy dispersive X-ray spectroscopy (EDS) and absorption spectra analysis. The upconversion emissions of Er³⁺ emerged under the excitation at 980 nm for glass ceramic heat-treated at 800 °C.     

Correlation of optical properties and temperature-induced irreversible phase transitions in europium-doped yttrium carbonate nanoparticles

Nanophase europium-doped yttrium carbonate precursors are subjected to heat treatments, ranging from 300 °C to 1100 °C for dwell times of 5 min, 30 min, and 180 min. XRD, TEM, FT-IR, fluorescence, fluorescence excitation, and fluorescence lifetime measurements are used to characterize the materials. Upon heating, the material transitions through several amorphous stages until it reaches the crystalline cubic Y₂O₃ phase. DSC measurements show an exothermic transition at 665.7 °C, indicating the formation of crystalline Y₂O₃. The grain size development is fitted by the relaxation equation and yields an activation energy of 50.3 kJ/mol. The amorphous phases are characterized by inhomogenously broadened optical spectra. Heating up to 700 °C leads to an increased fluorescence lifetime (from about 1 ms to 2.4 ms). As the material is heated to higher temperatures and completes the formation of the crystalline cubic Y₂O₃ phase, the optical spectra become narrower and the fluorescence lifetime decreases to about 1.2 ms.     

Comparative study of LiMn2O4 thin film cathode grown at high, medium and low temperatures by pulsed laser deposition

LiMn₂O₄ thin films with different crystallizations were respectively grown at high, medium and low temperatures by pulsed laser deposition (PLD). Structures, morphologies and electrochemical properties of these three types of thin films were comparatively studied. Films grown at high temperature (?873 K) possessed flat and smooth surfaces and were highly crystallized with different textures and crystal sizes depending on the deposition pressure of oxygen. However, films deposited at low temperature (473 K) had rough surfaces with amorphous characteristics. At medium temperature (673 K), the film was found to consist mainly of nano-crystals less than 100 nm with relatively loose and rough surfaces, but very dense as observed from the cross-section. The film deposited at 873 K and 100 mTorr of oxygen showed an initial discharge capacity of 54.3 μAh/cm² μm and decayed at 0.28% per cycle, while the amorphous film had an initial discharge capacity of 20.2 μAh/cm² μm and a loss rate of 0.29% per cycle. Compared with the highly crystallized and the amorphous films, nano-crystalline film exhibited higher potential, more capacity and much better cycling stability. As high as 61 μAh/cm² μm of discharge capacity can be achieved with an average decaying rate of only 0.032% per cycle up to 500 cycles. The excellent performance of nano-crystalline film was correlated to its microstructures in the present study.     

Highly ordered MnO2 nanowire array thin films on Ti/Si substrate as an electrode for electrochemical capacitor

AAO/Ti/Si substrate was successfully synthesized by a two-step electrochemical anodization of the aluminum film on the Ti/Si substrate and then used as template to grow nanowire arrays. The ordered MnO₂ nanowire arrays with about 40 nm diameters had been directly fabricated on AAO/Ti/Si substrate by direct current (DC) electrodeposition. The microstructure of the nanowire arrays was investigated by field-emission scanning electron microscopy, transmission electron microscopy and X-ray diffraction. Their electrochemical characterization was performed using cyclic voltammetry in 0.5 M Na₂SO₄ aqueous solution. The synthesized MnO₂ nanowires had amorphous nature until 400 °C. The deal capacitive behavior was obtained when the as-prepared sample was heat-treated at 200 °C. The specific capacitance of the electrode was about 254 F/g.     

Characterization and activity of visible-light-driven TiO2 photocatalyst codoped with nitrogen and cerium

Nitrogen and cerium codoped TiO₂ photocatalysts were prepared by a modified sol-gel process with doping precursors of cerium nitrate and urea, and characterized by X-ray diffraction (XRD), thermogravimetry-differential scanning calorimetry (TG-DSC), X-ray photoelectron spectra (XPS) and ultraviolet-visible light diffuse reflectance spectra (UV-vis DRS). Results indicate that anatase TiO₂ is the dominant crystalline type in as-prepared samples, and CeO₂ crystallites appear as the doping ratio of Ce/Ti reaches to 3.0 at%. The TiO₂ starts to transform from amorphous phase to anatase at 987.1 K during calcination, according to the TG-DSC curves. The XPS show that three major metal ions of Ce³⁺, Ce⁴⁺, Ti⁴⁺ and one minor metal ion of Ti³⁺ coexist on the surface. The codoped TiO₂ exhibits significant absorption within the range of 400-500 nm compared to the non-doped and only nitrogen-doped TiO₂. The enhanced photocatalytic activity of the codoped TiO₂ is demonstrated through degradation of methyl orange under visible light irradiation.     

Synthesis,Ferroelectric and Optical Properties of (Pb,Ca)TiO3 Thin Films by Soft Solution Processing

Calcium modified lead titanate sol was synthesized using a soft solution processing, the so-called polymeric precursor method. In soft chemistry method, soluble precursors such as lead acetate trihydrate, calcium carbonate and titanium isopropoxide, as starting materials, were mixed in aqueous solution. Pb_0.7Ca_0.3TiO₃ thin films were deposited on platinum-coated silicon and quartz substrates by means of the spinning technique. The surface morphology and crystal structure, dielectric and optical properties of the thin films were investigated. The electrical measurements were conducted on metal-ferroelectric-metal (MFM) capacitors. The typical measured small signal dielectric constant and dissipation factor at a frequency of 100 kHz were 299 and 0.065, respectively, for a thin film with 230 nm thickness annealed at 600°C for 2 h. The remanent polarization (2P_r) and coercive field (E _c) were 32 C/cm² and 100 kV/cm, respectively. Transmission spectra were recorded and from them, refractive index, extinction coefficient, and band gap energy were calculated. Thin films exhibited good optical transmissivity, and had optical direct transitions. The present study confirms the validity of the DiDomenico model for the interband transition, with a single electronic oscillator at 6.858 eV. The optical dispersion behavior of PCT thin film was found to fit well the Sellmeir dispersion equation. The band gap energy of the thin film, annealed at 600°C, was 3.56 eV. The results confirmed that soft solution processing provides an inexpensive and environmentally friendly route for the preparation of PCT thin films.     

Mesoporous Nb2O5 Films: Influence of Degree of Crystallinity on Properties

Nanocrystalline Nb₂O₅ films were prepared by an extended sol-gel method. The synthesis is based on the hydrolysis of a modified Nb-alkoxide precursor. Reaction of the modified precursor (Nb(OEt)₅ + 2 2,4-pentanedione) with water in ethanol leads to a homogeneous hydrolyzed solution, which is stable against precipitation of niobium oxide after evaporation of the ethanol and in the whole pH-range investigated (1–10). Autoclaving leads to amorphous gels, from which homogeneous nanocrystalline niobium oxide films of up to 15 m can be made. During annealing crystalline phases are first observed above 500°C with fully crystalline films of orthorhombic T-phase Nb₂O₅ attained at 600°C. The microstructural, crystallographic, optical and photoelectrical properties of the films were characterized by means of SEM, XRD, UV-VIS spectroscopy and surface photovoltage spectroscopy, respectively.     

Hydrothermal preparation and visible-light photocatalytic activity of Bi2WO6 powders

Bi₂WO₆ powder photocatalyst was prepared using Bi(NO₃)₃ and Na₂WO₄ as raw materials by a simple hydrothermal method at 150 °C for 24 h, and then calcined at 300, 400, 500, 600 and 700 °C for 2 h, respectively. The as-prepared samples were characterized with UV-visible diffuse reflectance spectra, fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and N₂ adsorption-desorption measurement. The photocatalytic activity of the samples was evaluated using the photocatalytic oxidation of formaldehyde at room temperature under visible light irradiation. It was found that post-treatment temperature obviously influenced the visible-light photocatalytic activity and physical properties of Bi₂WO₆ powders. At 500 °C, Bi₂WO₆ powder photocatalyst showed the highest visible-light photocatalytic activity due to the samples with good crystallization and high BET surface area.     

Influence of the crystallinity on the Li+ intercalation process in Nb2O5 films

Nb₂O₅ thin films were prepared by the Pechini method. The effect of the film crystallinity on the electrochemical and electrochromic properties was investigated. A relationship between the crystalline structure and the Li⁺ intercalation/extraction process, stability and kinetics was observed. A significant decrease in the electrochemical response was observed as a function of the number of cycles for films treated at 400 and 450 °C. However, as the calcination temperature increases this effect disappears. XRD studies shown that at 400 °C, the material is amorphous, evolving to orthorhombic phase. The transmittance variation as well as the coloration efficiency increases as the temperature is increased. In the initial cycles the intercalation charge is higher for the amorphous oxide than for the orthorhombic phase. However, the variation in the optical density is small. On the other hand, the charge of the orthorhombic phase oxide does not change. These results suggest that there are two different processes associated with Li⁺ intercalation, but only one of them leads to the coloration process.     

Growth and characterization of molybdenum oxide thin films prepared by photochemical metal–organic deposition (PMOD)

Molybdenum oxide thin films have been successfully prepared by direct UV irradiation of amorphous films of a molybdenum dioxide acetylacetonate complex on Si(1 0 0) substrates. Photodeposited films were characterized by X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) and the surface morphology examined by Atomic Force Microscopy (AFM). It was found that as-photodeposited films are uniform and smooth, with thickness of 350 nm, with rms surface roughness of 28 nm and contain non-stoichiometric oxides (MoO_3−x). The results of XRD analysis showed that post-annealing of the films in air at 450 °C transforms the sub-oxides to α-MoO₃ phase with a much rougher surface morphology (rms = 144 nm). The as-photodeposited MoO_3−x films are amorphous, and exhibit better optical quality than annealed films.     

Formation and performances of porous InVO4 films

Porous complex oxide films consisting of preferentially orientated orthorhombic phase of InVO₄ have been prepared using a novel simple method by pyrolysis of amorphous complex precursor. The formation and controlling of porous InVO₄ films can be easily obtained by modifying the calcination temperature. The pure orthorhombic InVO₄ phase can be obtained at a relatively lower temperature (500 °C), and the films are preferential orientation of the (200) face parallel to the substrate. The phase separation mechanism was suggested for the formation of porous films. Under visible light irradiation (λ>400 nm), porous InVO₄ films have shown the photocatalytic activity for photodegradation of gaseous formaldehyde, and can generate photocurrent. The electrochemical properties of the films with different crystal structure and pore structure were also investigated.     

Hydrothermal synthesis of cobalt carbonates using different counter ions: An efficient precursor to nano-sized cobalt oxide (Co3O4)

Synthesis of submicrometer crystalline particles of cobalt carbonate was achieved hydrothermally using different cobalt salts and urea with a molar ratio from 1:3 to 1:20 (cobalt salt:urea) in aqueous solutions at 160 °C for 24-36 h, in the presence of cetyltrimethylammonium bromide (CTAB) as a surfactant. Nanoparticles of Co₃O₄, with an average size from 30 to 39 nm, were obtained by thermal decomposition of CoCO₃ samples at 500 °C for 3 h in an electrical furnace. The as-synthesized products were characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), UV-Vis spectra and thermal analysis. Studying the optical properties of the as-prepared cobalt oxide nanoparticles showed the presence of two band gaps, the values of which confirmed the semiconducting properties of the prepared Co₃O₄.     

Synthesis and characterization of three-dimensionally ordered macroporous ternary oxide

A three-dimensionally ordered macroporous (3DOM) ternary oxide, CsAlTiO₄, with a framework related to ‘stuffed-tridymite’ has been synthesized at temperatures 500-700 °C using a sol-gel precursor solution and templating with polystyrene spheres. The 3DOM material displayed pore diameters of 0.5-0.8 μm with the walls composed of anhedral and acicular CsAlTiO₄ crystals whose dimensions ranged from 16 to 25 nm. Microanalysis confirmed near-stoichiometric proportions (1:1:1) of Cs, Al and Ti. The effect of sintering temperature on the macroporous structure and on the CsAlTiO₄ walls was studied. As the sintering temperature increased from 500 to 600 °C the unit cell parameters varied through dilation (a and b) and contraction (c-axis), followed by a reversal of these trends from 700 to 900 °C. This behaviour in non-equilibrated CsAlTiO₄ can be attributed to distortion of the (Al, Ti)O₄ tetrahedral framework, however at the highest temperature the cell constants stabilized close to those reported for single crystal CsAlTiO₄. X-ray amorphous content was significant in all materials varying from 73 wt% after 500^oC and reducing to 44 wt% at 900 °C.