Synthesis of titanate, TiO2 (B), and anatase TiO2 nanofibers from natural rutile sand

Titanate nanofibers were synthesized by hydrothermal method (150 °C for 72 h) using natural rutile sand as the starting materials. TiO₂ (B) and anatase TiO₂ (high crystallinity) nanofibers with the diameters of 20-100 nm and the lengths of 10-100 μm were obtained by calcined titanate nanofibers for 4 h at 400 and 700 °C (in air), respectively. The samples characterized by XRD, SEM, TEM, SAED, HRTEM, and BET surface area. This synthesis method provides a simple route to fabricate one-dimensional nanostructured TiO₂ from low cost material.     

The release of TiO2 and SiO2 nanoparticles from nanocomposites

There is a growing interest in the development of nanocomposites consisting of organic polymers and TiO₂ or amorphous SiO₂ nanoparticles. These nanoparticles may be released from nanocomposites. There is evidence that amorphous SiO₂ and TiO₂ nanoparticles can be hazardous. Thus, in the design of nanocomposites with such nanoparticles, hazard reduction extending to the full nanocomposite life cycle would seem a matter to consider. Options for hazard reduction include: changes of nanoparticle surface, structure or composition, better fixation of nanoparticles in nanocomposites, including persistent suppression of oxidative damage to polymers by nanoparticles, and design changes leading to the release of relatively large particles.     

Nanocrystallization of anatase in amorphous TiO2

The kinetics of nanocrystallization in amorphous TiO₂ has been studied in non-isothermal conditions by DSC. It was found that this process could be well described by standard Johnson-Mehl-Avrami-Kolmogorov (JMA) model with kinetic exponent m≅1. The kinetic parameters were calculated by simultaneous analysis of experimental data taken at different heating rates. These parameters were used as a basis for prediction of crystallization kinetics in isothermal conditions. The agreement between the JMA model prediction and experimental data depends on the method of preparation of amorphous TiO₂.     

磷酸对TiO2纳米粒子光催化剂的改性

通过浸渍过程实现了磷酸对溶胶水热法合成的锐钛矿相TiO2纳米粒子的改性.重点研究了磷酸修饰对纳米锐钛矿相TiO2的热稳定性及光催化活性的影响.结果表明,磷酸修饰显著地提高了纳米锐钛矿相TiO2热稳定性,甚至经过800℃热处理后仍然具有以锐钛矿相为主的相组成.在光催化降解罗丹明B(RhB)过程中经过700℃热处理的磷酸修饰的样品表现出了优于商品P25-TiO2的活性.     

TiO2 nanoparticles incorporated with CuInS2 clusters: preparation and photocatalytic activity for degradation of 4-nitrophenol

TiO₂ nanoparticles incorporated with CuInS₂ clusters were prepared in a solvothermal process and characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), and energy-dispersion X-ray analysis (EDX). Compared with pure TiO₂ nanoparticles, the TiO₂ nanoparticles incorporated with CuInS₂ clusters display higher photocatalytic activity with 99.9% of degradation ratio of 4-nitrophenol after 2 h irradiation. In order to investigate the effect of the CuInS₂ clusters on the photocatalytic activity of TiO₂ nanoparticles, diffuse reflectance UV–Vis spectra (DRS), photoluminescence (PL) spectra, and photocurrent action spectra were measured. The results indicate that the enhanced photocatalytic activity is probably due to the interface between TiO₂ and CuInS₂ as a trap of the photogenerated electrons to decrease the recombination of electrons and holes.     

IR-analysis of H-bonded H2O on the pure TiO2 surface

The surface state of optically pure polydisperse TiO₂ (anatase and rutile) was determined by infra-red (IR) spectroscopy analysis in the temperature range of 100–453 K. Anatase A300 spectrum, contrary to rutile R300 one, has a broad three-component absorption band with peaks at 1048, 1137 and 1222 cm⁻¹ in the spectral range of δ(Ti–O–H) deformation vibrations. For rutile R300 we observed a very weak band at 1047 cm⁻¹, and for the thermal treated rutile R900 these bands were not appeared at all. The analysis of temperature dependencies for the mentioned absorption bands revealed the spectral shift of 1222 cm⁻¹ band towards the high frequencies, when the temperature increased, but the spectral parameters of 1137 and 1048 cm⁻¹ bands remained the same. The temperature of 1222 cm⁻¹ band maximum shift was 373–393 K and correlated with DSC data. Obtained results allowed to assign 1222 cm⁻¹ band to the deformation vibrations of OH-groups, bounded to the surface adsorbed water molecules by weak hydrogen bonds (5 kcal/mol). During the temperature growth these molecules desorbed, which also resulted in the intensity decreasing of stretching OH-groups vibration IR-bands at 3420 cm⁻¹. The destruction and desorption of surface water complexes led to Ti–O–H bond strengthening. IR bands at 1137 and 1048 cm⁻¹ were attributed to the stronger bounded adsorbed water molecules, which are also characterized with stretching OH-groups vibration bands at 3200 cm⁻¹. These surface structure were additionally stabilized by hydrogen bonds with the neighbouring TiO₂ lattice anions and other OH-groups, and desorbed at higher temperatures.     

Photoinduced interactions between colloidal TiO2 nanoparticles and calf thymus-DNA

The interaction of colloidal TiO₂ nanoparticles with calf thymus-DNA was studied by using absorption, FT-IR, steady state and time resolved fluorescence spectroscopic techniques. The apparent association constant has been deduced (K_app = 2.85 × 10³ M⁻¹) from the absorption spectral changes of the DNA-colloidal TiO₂ nanoparticles using the Benesi–Hildebrand equation. Addition of colloidal TiO₂ nanoparticles quenched the fluorescence of EtBr–DNA. The number of binding sites (n = 0.97) and the apparent binding constant (K = 6.68 × 10³ M⁻¹) were calculated from relevant fluorescence quenching data. The quenching, through a static mechanism, was confirmed by time resolved fluorescence spectroscopy.     

Defect microstructures of TiO2 rutile due to Zr dissolution and expulsion

Defect microstructure of Zr-dissolved TiO₂ polycrystals, homogenized as rutile structure at 1600 °C and then aged at 900 °C for 2-200 h in air, was characterized by analytical electron microscopy. Diffuse diffractions occurred at 1/2(211) as a result of Zr⁴⁺ substitution for Ti⁴⁺ with volume/charge compensating defect clusters. Upon annealing at 900 °C, plate-like Guinier and Preston (G.P.) zone appeared with the plate surface parallel to (100) and (010) and in association with dislocations. Commensurate superstructures with apparent triple {101} and {111} periodicity also occurred as metastable intermediates, which are presumably the precursor of the equilibrium ZrTi₂O₆ precipitate.     

Visible-light responsive dye-modified TiO2 photocatalyst

A series of dye-modified TiO₂ photocatalysts were synthesized using dye Chrysoidine G (CG), tolylene-2,4-diisocyanate (TDI), and commercial TiO₂ (Degussa P25) as starting materials. TDI was used as a bridging molecule whose two -NCO groups reacted with Ti-OH of TiO₂ and -NH₂ groups of CG, respectively. As a result, special organic complexes were formed on the TiO₂ surface via stable π-conjugated chemical bonds between TiO₂ and dye molecules, confirmed by FT-IR, XPS, and UV-vis spectra. Due to the existence of π-conjugated surface organic complexes, the as-synthesized photocatalysts showed a great improvement in visible absorption (400-550 nm). Methylene blue, as a photodegradation target, was used to evaluate the photocatalytic performance, and the dye-modified TiO₂ exhibited much better activity under the visible light irradiation than bare TiO₂.     

TiO2纳米线的制备及其光电性能研究

利用在钛箔表面沉积一层TiO₂纳米粒子作为晶种，与NaOH反应，制备了一维物质TiO₂纳米线。并用XRD、SEM、TEM、HRTEM及EDS等分析手段对TiO₂纳米线的成分、形貌、结构进行表征。结果表明，采用该方法制得的TiO₂纳米线直径在20～50 nm左右、长度可达几微米。反应温度能显著影响所得纳米线的形貌。研究了TiO₂纳米线的光电化学性能。随反应温度的升高TiO₂纳米线光电转换效率增大。     

溶胶-凝胶法低温制备N掺杂TiO2可见光光催化剂

为了满足低温制备可见光光催化材料的需要,采用溶胶-凝胶法制备TiO₂纳米晶溶胶,再与聚乙烯基吡咯烷酮(PVP)直接反应制备N掺杂TiO₂可见光光催化剂。通过XPS分析,说明N取代了部分晶格中的O,UV-Vis漫反射吸收光谱显示,光催化剂具有明显的可见光响应,这是由于N原子的2p轨道位于O原子的2p轨道之上,从而使得价带和导带间的能量带隙变窄,引起吸收带红移,产生明显的可见光吸收。依靠亚甲基兰(MB)的可见光降解实验证明,N掺杂光催化剂具有良好的可见光光催化活性,16 h MB降解率接近25％。     

载有C60的TiO2纳米粒子光催化活性

以水溶性C₆₀和TiO₂粒子为前驱体,采用水热法制备了载有C₆₀的锐钛矿型TiO₂纳米粒子。应用X射线衍射、透射电子显微镜、红外光谱、紫外-可见漫反射光谱、荧光光谱对产物进行了表征。以对-硝基苯酚为模型污染物研究了产物的光催化活性,结果表明适量负载C₆₀可以提高TiO₂纳米粒子的光催化活性,C₆₀起着传输电子、促进TiO₂光生载流子分离的作用,且经7次循环使用后对-硝基苯酚的降解效率仍能达到74%。讨论了载有C₆₀的TiO₂纳米粒子光催化降解对-硝基苯酚的机理。     

静电自组装制备纳米TiO2/SiO2光催化材料

采用静电自组装方法制备了纳米TiO2/SiO2光催化材料。采用巯丙基三甲氧基硅烷偶联剂对SiO2进行干法改性,采用双氧水/冰醋酸将偶联剂巯基基团氧化为磺酸基基团。在正负电荷的吸引下,带负电荷的SiO2与带正电荷的钛聚合阳离子自发地组装在一起,经一定温度热处理得到纳米TiO2/SiO2光催化材料。采用XRD、FTIR、PL、UV-Vis DRS、SEM和ICP等对材料进行了分析和表征。采用甲基橙溶液评价材料的光催化性能。结果表明:SiO2促使锐钛矿的形成,抑制锐钛矿向金红石的转变,减小TiO2的晶粒尺寸,使得TiO2光吸收波长发生蓝移。TiO2与SiO2通过Si-O-Ti键发生结合。采用静电自组装方法制备的材料中TiO2的含量高于传统方法,导致材料的光催化性能有所提高。     

Syntheses of TiO2(B) nanowires and TiO2 anatase nanowires by hydrothermal and post-heat treatments

TiO₂(B) nanowires and TiO₂ anatase nanowires were synthesized by the hydrothermal processing in 10 M NaOH aq. at 150 °C followed by the post-heat treatment at 300-800 °C. As-synthesized Na-free titanate nanowires (prepared by the hydrothermal treatment and repeated ion exchanging by HCl (aq.) were transformed into TiO₂(B) structure with maintaining 1-D morphology at 300-500 °C, and further transformed into anatase structure at 600-800 °C with keeping 1-D shape. At 900 °C, they transformed into rod-shaped rutile grains. Microstructure of these 1-D TiO₂ nanomaterials is reported.     

Zeta potential of shape-controlled TiO2 nanoparticles with surfactants

Zeta potential of shape- and size-controlled TiO₂ nanoparticles obtained with the introduction of surfactants during synthesis was measured at different pH values. A unique finding is that TiO₂ nanoparticles shaped by sodium dodecyl sulfate (SDS) have double isoelectric points (IEPs), while other shape-controlled TiO₂ nanoparticles have only one IEP. The double IEPs might be due to the complex chemistry of TiO₂ nanoparticles with the presence of impurities (Na, S, C, etc.). At neutral pH, shape- and size-controlled TiO₂ nanoparticles have more negative zeta potential values and lower IEPs than TiO₂ nanoparticles obtained without the addition of surfactants during synthesis and the commercial anatase TiO₂ nanoparticles Degussa P-25. The lower IEPs could be attributed to the presence of carbonates on particle surfaces. The IEP value of TiO₂ nanoparticles increases with an increase in calcination temperature. The results suggest that the zeta potential of TiO₂ nanoparticles can be manipulated with the addition of surfactants during the synthesis process.     

双介孔结构的纳米TiO2/I2复合材料的制备及其可见光催化性能

以钛酸丁酯为前驱体, 碘溶胶为碘源, 在室温下采用水解沉淀法制备了单质碘和纳米TiO₂复合的双介孔结构光催化剂(M-I₂-TiO₂). 采用X射线衍射(XRD)、透射电子显微镜(TEM)、比表面分析(BET)、紫外-可见(UV-Vis)漫反射光谱和傅里叶变换-红外光谱(FT-IR)对M-I₂-TiO₂进行了表征. 以次甲基蓝(MB)溶液为模拟废水, 对M-I₂-TiO₂的光催化性能进行了评价, 研究了不同热处理温度对光催化活性的影响. 结果表明, M-I₂-TiO₂在可见光区有显著的吸收, 300 ℃热处理得到的样品比表面积高达227.6 m²/g, 600 ℃热处理所得样品的比表面积仍高达111.8 m²/g, 而400 ℃热处理所得样品具有最好的光催化降解性能. 双介孔结构纳米TiO₂/I₂复合材料的光催化降解性能显著高于相同方法制备的纯TiO₂和Degussa P-25商业产品. 催化剂经6次重复使用其光催化活性基本保持不变.     

转晶纳米TiO2的制备及其声催化活性的研究

近几年兴起的半导体多相光催化技术在有机废水处理方面受到了人们的普遍关注[1,2]。众多的半导体光催化剂材料中,TiO2因其化学性质稳定和催化效率高而倍受青睐[3,4]。在紫外光的照射下,TiO2与H2O产生具有极强氧化能力的HO·自由基,最终可使废水中的有机物完全降解生成CO2,H2O以     

Catalytic oxidation of no to NO2 over Cr/TiO2 and Cu/TiO2 under oxidizing atmosphere

The catalytic activity of Cr/TiO₂ and Cu/TiO₂ for the oxidation of NO under an oxidizing atmosphere has been examined. Both catalysts had excellent ability for the oxidation of NO to NO₂ in the temperature range of 350–400°C.     

TiO2纳米管阵列覆盖Si薄膜光催化还原CO2性能的研究

本工作采用CVD法在阳极氧化TiO2纳米管阵列膜表面沉积一层非晶Si膜,通过退火后得到晶化了的Si膜/TiO2纳米管阵列的复合结构,并初步就其光催化还原CO2制备碳氢化合物的活性进行研究。拉曼光谱(Raman)、X射线衍射(XRD)、场发射扫描电镜(FE-SEM)、高分辨透射电子显微镜(TEM)等微结构表征结果表明所制备的TiO2纳米管阵列的厚度为270 nm左右,管直径约为70 nm,管壁厚度约为16 nm。覆盖的Si膜已晶化,其厚度约为300 nm。通过高效液相色谱(HPLC)及总有机碳(TOC)来检测光催化还原液相产物中的甲酸及总有机碳含量,发现负载Si膜后的TiO2纳米管阵列光催化性能有所提高,在装有400cut滤光片氙灯照射2 h下TOC含量从21.2 mg.L-1增长到29.5 mg.L-1,表明Si与TiO2的复合可有效的提高光催化还原CO2的活性,这可能与该异质结结构可增加对光的吸收并且可降低光生空穴-电子对复合有关。光催化循环实验表明所制得的催化剂在循环5次后仍可保持91.6%的催化活性。     

纳米TiO2低温水解法的晶型控制合成及其表面织构的研究

分别以TiCl₄，Ti(NO₃)₄和Ti(SO₄)₂为前驱体，在低温和强酸性条件下，通过水解反应可控地合成了具有不同晶相组成，且比表面积较高的纳米TiO₂，并用XRD，TEM和N₂^-吸附脱附技术对其晶相、粒径大小、形貌及比表面积进行了表征。结果表明，钛离子在有Cl^-、NO₃^-存在的酸性溶液中水解，水解温度≤80 ℃，可以生成结晶良好的具有细小晶粒尺寸和较高比表面积的金红石型纳米TiO₂粉体，水解温度>80 ℃，反而有锐钛矿型TiO₂生成，而在有SO₄^2-存在的酸性溶液中，TiO₂样品的晶相组成不随水解温度的变化而改变，均为锐钛矿型，其比表面积可达300 m²·g^-1。