基于高双折射光子晶体光纤与光纤环的超宽带可调谐微波光子滤波器

提出一种基于高双折射光子晶体光纤与光纤环的超宽带可调谐微波光子滤波器.以多波长光纤激光器作为光源,向高双折射光子晶体光纤内填充温敏液体,通过改变填充温敏液体的温度,高双折射光子晶体光纤可具有不同的双折射,得到不同波长间隔的激光,从而使微波光子滤波器具有不同的自由频谱范围.当温度的变化范围为20~80℃时,仿真测得微波光子滤波器自由频谱的变化范围为2.49~39.9GHz.引入光纤环构建级联型微波光子滤波器,滤波器的主旁瓣抑制比可提高到33.6dB,Q值可达到499,提高了滤波器的频率选择性.     

单像素压缩成像高质量图像重建特征函数

通过测量矩阵获取Gram矩阵,梳理了Gram矩阵与系统点扩散函数的关系,进而基于点扩散函数提出最强旁瓣峰值大小、叠加旁瓣峰值大小、空间距离和频谱余弦相似度4个特征参量。在此基础上,构建了一种单像素压缩成像高质量图像重建的特征函数,建立了可重建的目标稀疏度与特征函数的关系,并通过数值模拟和实验验证了所提特征函数的有效性,该工作对于单像素成像系统测量矩阵的优化设计具有重要借鉴意义。     

多模声波导结构光纤的应变与温度系数计算方法

在基于布里渊拍频谱功率测量的分布式光纤传感中,提出对多模声波导结构光纤的应变与温度系数进行理论计算的方法。布里渊拍频谱的功率与光纤的有效折射率、杨氏模量、泊松比、声光有效面积等参数有关,这些参数会随光纤中应变和温度改变。通过建立应变和温度与布里渊拍频谱功率之间关系,可在已知光纤的折射率分布的情况下,从理论上推导出多模声波导结构光纤的布里渊拍频功率-应变系数和布里渊拍频功率-温度系数。以大有效面积光纤(LEAF)为例,计算了光纤的应变和温度系数,并与实验测量结果进行比较。结果表明,使用该方法得到的理论计算结果与实验值相吻合,验证了该计算方法的有效性。     

双余弦相位调制对超高斯脉冲的频谱压缩

针对具有非线性负啁啾的超高斯脉冲,提出了一种双余弦相位调制方法,采用该方法对高非线性光纤中超高斯脉冲的频谱压缩进行优化。结果表明:由于初始超高斯脉冲的非线性负啁啾与非线性光纤中自相位调制引起的正啁啾失配导致时间相位不平坦,频谱出现分裂和旁瓣,压缩质量受限。通过对超高斯脉冲进行外部的两个余弦相位补偿调制可以减少频谱旁瓣的产生,延长频谱压缩距离,提高频谱压缩质量;其中这两个余弦相位调制的振幅和频率来自于对超高斯脉冲的非线性相移分析;在大范围展宽因子下,超高斯脉冲的频谱压缩质量也可以优化。     

提升管喷嘴进料段内气固两相流动的数值模拟

本文采用κ-ε-κ_p-κ_(pg)-θ模型,模拟了提升管喷嘴进料段内三维稠密气固交叉射流的复杂流动现象.结果表明,实验值和模拟值具有相同的变化趋势,再现了提升管喷嘴进料段内颗粒相的流动特点.     

光纤光栅马赫-曾德干涉仪条纹信号的傅里叶分析

基于长周期光纤光栅马赫-曾德干涉仪的频分复用技术是实现光纤多参量传感的重要途径.研究了频分复用中复合条纹信号的傅里叶处理方法,分析了傅里叶频谱中和频与差频信号的幅值与单个干涉条纹信号的关系,提出了抑制和频与差频信号的有效方法,即改变光栅结构参量适当降低中心波长处的条纹对比度以提高频谱信号的信噪比,增加特征频谱滤波的有效性.结果表明:经过优化调整的傅里叶频谱信噪比可以提高至原来的2倍以上;对比频谱调整后恢复相位的余弦曲线与原条纹信号发现,频谱信噪比提高的同时保留了反映各单个原条纹特征的足够相位信息.该光谱优化方法可为基于光纤光栅马赫-曾德干涉仪和频分复用的光纤多参量传感技术提供理论与技术指导.     

长脉冲抽运光子晶体光纤四波混频和超连续谱的理论研究

本文数值研究了长脉冲抽运光子晶体光纤四波混频和超连续谱的产生.依据准连续波近似下的相位匹配条件和能量守恒定律,能够理论上确定在光子晶体光纤正常色散区抽运时,四波混频效应产生的信号光和空闲光波长;以及在光纤反常色散区抽运时,调制不稳现象产生的两个对称旁瓣波长.利用自适应分步傅里叶法,定量地模拟了利用波长为1064 nm的亚纳秒激光器抽运两种不同色散特性的光子晶体光纤四波混频效应和超连续谱的产生,模拟结果与实验结果符合非常好. 关键词： 光子晶体光纤 超连续谱 四波混频 自适应分步傅里叶法     

L波段掺铒光纤放大器的自发辐射谱与增益的研究

利用Giles模型对L波段掺铒光纤放大器小信号增益特性进行了数值模拟,模拟结果表明最佳铒纤长度并不是一定值,它随输入信号波长的不同而改变,较短的波长对应较短的光纤长度;在数值模拟、分析的基础上,分别采用7m和9m的L波段铒光纤构成长波段掺铒光纤放大器,通过实验测量,分析比较了它们的自发辐射谱以及增益和噪声指数,得到了光纤长度对L波段增益谱、噪声指数和自发辐射谱的影响规律;最后,辅以C波段掺铒光纤放大器加以分析,指出了适合于放大L波段信号的最佳自发辐射谱型。     

基于数字全息图的光纤折射率测量研究

利用数字全息显微层析技术构建了光纤折射率测量的测试系统, 包括光路系统与软件系统. 以物光波的相位分布曲线为依据由CCD记录最优的数字全息图; 在优化频谱图的基础之上对全息图做频域滤波, 准确选取物光波所对应的频谱范围; 使用基于角谱理论的再现算法提取出物光波的相位分布信息, 并通过模拟全息图验证相位提取的准确性; 由单幅全息图提取的相位分布信息, 结合光纤的多层模型, 还原出光纤断层面沿直径方向的折射率分布. 以单模、多模光纤为实验样品进行了测量, 测量结果与S14折射率测量仪的测量结果吻合, 精度可达10^-4. 实验对比结果表明本文方法可简单、快速、准确地测量光纤内部的折射率. 本文还对特种光纤的折射率进行了测量研究.     

光纤布拉格光栅自致啁啾效应的研究

根据耦合模理论,采用传输矩阵法分析了相位掩模法制作的光纤布拉格光栅的反射谱特性.设计了一种新的写制光纤光栅的光路,利用高斯激光光束写制出具有短波自致啁啾效应的切趾光栅(栅长0.015 m).对具有短波自致啁啾效应的光纤光栅进行了物理切割(剩余光栅的长度分别取0.007 m和0.0055 m),得到了一种新型的具有长波自致啁啾效应的光纤光栅.原本的自致啁啾光栅反射谱中旁瓣分布在短波长方向,而得到的新型自致啁啾光栅的反射谱中长波长方向的旁瓣更为明显.基于对光纤布拉格光栅自致啁啾效应的分析,提出一种新型类高斯切趾函数,以此函数对自致啁啾效应进行数值模拟,得到了与实验结果相一致的光谱图.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

Optical Pulse Compression Schemes That Use Nonlinear Bragg Gratings

Nonlinear optical pulse compression of picosecond pulses typically requires long lengths of optical fiber and multiple components. Periodic structures, such as fiber Bragg gratings, are highly dispersive at wavelengths outside of the photonic bandgap. This implies that such gratings can be used as very short all-fiber compressors. In this paper a number of such compression schemes are reviewed involving uniform and nonuniform fiber Bragg gratings, relying on both soliton and nonsoliton compression principles. Experimental results supporting the corresponding underlying theory are also presented. Finally, an extension of one of the compression schemes is shown, which allows the generation of adjustable high-repetition rate soliton trains.