Er3+掺杂SiO2复合的Al2O3粉末结构及光致发光特性

采用溶胶-凝胶(sol-gel)工艺制备0.1 mol% Er³⁺掺杂Al₂O₃体系和SiO₂-Al₂O₃复合体系粉末. 实验结果表明：5 mol%的SiO₂复合加入Al₂O₃抑制γ→θ和θ→α相转变. 掺0.1 mol%Er³⁺:Al₂O₃体系粉末，900℃烧结，在1.47—1.63μm波段内光致发光(PL)谱为中心波长1.53 μm、半高宽56 nm的单一宽峰，1000—1200℃烧结，劈裂为多峰PL谱. 掺0.1 mol%Er³⁺:SiO₂-Al₂O₃复合体系粉末，在高达1200℃烧结，仍保持中心波长1.53 μm的单一宽峰PL谱，由于—OH更完全的脱除，PL强度较900℃烧结Al₂O₃体系，SiO₂-Al₂O₃复合体系均提高1个数量级. 关键词： 2-Al₂O₃复合体系')" href="#">SiO₂-Al₂O₃复合体系 掺铒 溶胶-凝胶工艺 光致发光     

Infrared-to-visible upconversion in Er and Er/Yb activated Sb2O4 nanopowders prepared by sol-gel route

We prepared Er³⁺ doped and Er³⁺/Yb³⁺ codoped Sb₂O₄ nanocrystals by the sol-gel method. The Raman, X-ray diffraction (XRD), transmission electron microscope (TEM), and photoluminescence spectra of the samples were studied. The phonon energy of the Sb₂O₄ nanocrystals is very low (the maximum value being 461 cm⁻¹). The upconversion (UC) red emission of the Er³⁺/Yb³⁺ codoped sample is very strong at 975 nm laser diode excitation. The Sb₂O₄ nanocrystals will be a promising luminous material.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Effect of Ce on the spectroscopic properties in Er doped TeO2-GeO2-Nb2O5-Li2O glasses

The Ce³⁺ ion was introduced into Er³⁺ doped TeO₂-GeO₂-Nb₂O₅-Li₂O (TGNL) glass to improve the 1.5 μm fluorescence characteristics. As increasing of Ce³⁺ concentration, the lifetime of Er³⁺:⁴I_11/2 level is shortened form 360 to 225 μs, while the Er³⁺:⁴I_13/2 level remains unchanged. Accordingly, the upconversion fluorescence (blue, green and red) was quenched. Improved 1.5 μm emission is obtained and the reason is ascribed to the increase of nonradiative rate between the ⁴I_11/2 and ⁴I_13/2 level of the Er³⁺ ions.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

The up-conversion properties of Yb and Er doped Y4Al2O9 phosphors

Er³⁺ doped and Yb³⁺/Er³⁺ co-doped Y₄Al₂O₉ phosphors are prepared by the sol-gel method. The effect of dopant concentration on the structure and up-conversion properties is investigated by X-ray diffraction (XRD) and photoluminescence, respectively. XRD pattern indicates that the sample structure belongs to monoclinic. Under 980 nm excitation, the green and red up-conversion emissions are observed and the emission intensities depended on the Yb³⁺ ion concentration. The green up-conversion emissions decrease with the increase of Yb³⁺ concentration, while red emission increases as Yb³⁺ concentration increases from 0 to 8 at% and then decreases at high Yb³⁺ concentration. The mechanisms of the up-conversion emissions are discussed and results shows that in Er³⁺ and Yb³⁺/Er³⁺ co-doped system, cross-relaxation (CR) and energy transfer (ET) processes play an important role for the green and red up-conversion emissions.     

980 nm激发下Er3+/Yb3+共掺杂ZrO2-Al2O3粉末的上转换发光特性

通过固相反应法制备了Er³⁺/Yb³⁺共掺杂ZrO₂-Al₂O₃粉末的样品，并对样品在980nm激光激发下的上转换发光特性进行了研究.从发射光谱可以发现，在可见光范围内有3个强的发光带，一个位于654nm附近的红光带和两个分别位于545nm、525nm附近的绿光带，分别对应于Er³⁺离子的以下辐射跃迁：⁴F_9/2→⁴I_15/2、⁴S_3/2→⁴I_15/2、 ²H_11/2→⁴I_15/2.其中又以Er³⁺离子的⁴F_9/2→⁴I_15/2跃迁产生的红色荧光辐射最强.对其上转换发光机制进行了分析，发现这三个发光过程都是双光子过程.对样品粉末进行了XRD检测，发现ZrO₂主要以立方相为主，并且计算得到了这种立方结构的晶格常数.Al₂O₃固溶于ZrO₂中，Al³⁺嵌入ZrO₂后产生氧空位，导致ZrO₂晶体的对称性降低，这种结构变化更有利于提高上转换效率，即上转换发光强度增强. 关键词： 3+/Yb³⁺')" href="#">Er³⁺/Yb³⁺ 上转换 2-Al₂O₃')" href="#">ZrO₂-Al₂O₃ 荧光 稀土     

Creation of nanoparticles and luminescence in Al2O3 crystal by Zn ion implantation

Single crystal α-Al₂O₃ wafers were implanted with 45 keV Zn ions up to a fluence of 1×10¹⁷ ions/cm², and were then subjected to furnace annealing in oxygen atmosphere at different temperatures. Various techniques have been applied to study the creation of nanoparticles (NPs), defects and their thermal evolutions, as well as their effects on optical properties of Al₂O₃. Our results clearly show that Zn NPs have been synthesized in the as-implanted sample and they begin to be oxidized at 500 °C. Two broad photoluminescence bands appear in the Zn ion-implanted samples and their intensities depend on the annealing temperatures. The results have been interpreted in view of creation of the defects and NPs, Zn atoms diffusion as well as their thermal evolution during annealing.     

Enhanced photoluminescence of Sm/Bi co-doped Gd2O3 phosphors by combustion synthesis

Gd₂O₃:Sm³⁺ and Gd₂O₃:Sm³⁺,Bi³⁺ powders were prepared by a combustion method. Their structures were determined using X-ray diffraction. UV-visible absorption and photoluminescence spectra were investigated for Gd₂O₃:Sm³⁺ and Gd₂O₃:Sm³⁺,Bi³⁺ at different annealing temperatures and different doping concentrations. The emission spectra of all samples presented the characteristic emission narrow lines arising from the ⁴G_5/2→⁶H_J transitions (J=5/2, 7/2, and 9/2) of Sm³⁺ ions upon excitation with UV irradiation. The emission intensity of Sm³⁺ ions was largely enhanced with introducing Bi³⁺ ions into Gd₂O₃:Sm³⁺ and the maximum occurred at a Bi³⁺ concentration of 0.5 mol%. The relevant mechanisms were discussed with the sensitization theory by Dexter and the aggregation behavior of Bi³⁺ ions.     

Preparation and optical properties of ZnGa2O4:Cr thin films derived by sol-gel process

ZnGa₂O₄:Cr³⁺ thin films with bright red emission were synthesized using a sol-gel process, characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Auger electron spectroscopy (AES) and UV-vis and fluorescence spectrophotometry measurements. Effects of calcining temperature, film thickness, calcining duration and substrates on the crystal structure and photoluminescent property have been investigated. It is found that the crystallinity, Ga/Zn ratio and band gap energy (E_g) are significant factors influencing optical characteristics, while the nature of substrates affect the surface morphologies of ZnGa₂O₄:Cr³⁺ thin films.     

Effect of Eu,Tb codoping on the luminescent properties of Y2O3 nanorods

Red-emitting Y₂O₃:Eu³⁺ and green-emitting Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺, Tb³⁺ nanorods were synthesized by hydrothermal method. Their structure and micromorphology have been analyzed by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photoluminescence (PL) property of Y₂O₃:Eu³⁺,Tb³⁺ phosphor was investigated. In the same host (Y₂O₃), upon excitation with ultraviolet (UV) irradiation, it is shown that there are strong emissions at around 610 and 545 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺ and ⁵D₄-⁷F₅ transition of Tb³⁺, respectively. Different qualities of Eu³⁺and Tb³⁺ ions are induced into the Y₂O₃ lattice. From the excitation spectrum, we speculate that there exists energy transfer from Tb³⁺ to Eu³⁺ ions .The emission color of powders reveals regular change in the separation of light emission. These powders can meet with the request of optical display material for different colors or can be potentially used as labels for biological molecules.     

NIR to visible upconversion in Er/Yb co-doped CaYAl3O7 phosphor obtained by solution combustion process

Using the combustion synthesis, CaYAl₃O₇:Er³⁺ phosphor powders co-doped with Yb³⁺ have been prepared at low temperatures (550 °C) in a few minutes. Formation of the compound was confirmed by X-ray powder diffraction. Near-infrared to visible upconversion fluorescence emission in the Er³⁺ doped CaYAl₃O₇ phosphor powder has been observed. The effect of co-doping with triply ionized ytterbium in the CaYAl₃O₇:Er³⁺ phosphor has been studied and the process involved is discussed.     

Enhanced luminescence of Dy in Y3Al5O12 by Bi co-doping

In the present paper, phosphors with the composition Y_3−x−yAl₅O₁₂:Bi³⁺_x, Dy³⁺_y were synthesized with solid state reactions. The luminescence properties of Bi³⁺ and Dy³⁺ in Y₃Al₅O₁₂(YAG) and the energy transfer from Bi³⁺ to Dy³⁺ were investigated in detail. Bi³⁺ in YAG emits one broad band peaking at 304 nm which can be ascribed to the transition from excited states ³P_{0, 1} to ground state ¹S₀. Dy³⁺ in YAG emits two groups of peaks around 484 and 583 nm, respectively, which can be ascribed to the transitions from excited state ⁴F_9/2 to ground states ⁶H_15/2 and ⁶H_13/2. The co-doping of Bi³⁺ enhances the luminescent intensity of Dy³⁺ by ∼7 times because Bi³⁺ can transfer the absorbed energy to Dy³⁺ efficiently. The mechanism of energy transfer was also discussed.     

SMA-g-MPEG comb-like polymer as a dispersant for Al2O3 suspensions

SMA-g-MPEG comb-like polymer is first employed as the dispersant of Al₂O₃ suspensions in this paper. The comb-like polymer has anionic polycarboxylate backbone, which makes the polymer easily absorbed on the cationic surface of Al₂O₃ particles; on the other hand, the comb-like polymer has hydrophilic MPEG side chains, which extend into the solution to provide steric repulsion after the comb-like polymer is absorbed on the surface of Al₂O₃ particles. The adsorption behavior, zeta potential, apparent viscosity, granularity and TEM images of the Al₂O₃ suspensions using SMA-g-MPEG as dispersant are investigated. The addition of SMA-g-MPEG improves the dispersibility and decreases the apparent viscosity of the Al₂O₃ suspension observably. The impacts of the length of side chains on the dispersion of Al₂O₃ suspensions are particularly discussed. The adsorbed molecular number of the dispersant decreased by increasing the length of side chains. The zeta potential of Al₂O₃ suspension is more negative by using comb-like polymer with shorter side chains. Based on the steric repulsion and adsorbed molecular number, SMA-g-MPEG with moderate length of side chain is found to have the best dispersibility for Al₂O₃ suspension.     

Al2O3:V3+晶体局域结构及其自旋哈密顿参量研究

提出了解释掺杂离子局域结构畸变的配体平面移动模型，建立了此模型下晶体微观结构与自旋哈密顿参量之间的定量关系.在考虑自旋与自旋、自旋与另一电子轨道和轨道与轨道作用等微小磁相互作用的基础上，采用全组态完全对角化方法，对Al₂O₃晶体中V³⁺的局域结构和自旋哈密顿参量进行了系统的研究.结果表明，V³⁺掺入Al₂O₃晶体后，上下配体氧平面间距离增大了0.0060 nm.从而成功地解释了Al₂O₃:V³⁺晶体的自旋哈密顿参量.在此基础上，研究了三角晶场下3d²离子自旋哈密顿参量的微观起源.研究发现，自旋三重态对自旋哈密顿参量的贡献是主要的，微小磁相互作用对自旋哈密顿参量的贡献只与自旋三重态有关.     

Anodization of aluminium thin films on pSi and annihilation of strong luminescence from Al2O3

Photoluminescence (PL) of Al₂O₃ films obtained by anodization of thermally evaporated and annealed thin Al films on p⁺⁺Si in 0.3 M oxalic acid has been investigated. Thermal annealing at 200–950 °C under the dry nitrogen atmosphere was used for deactivation of luminescence centres. Luminescence from as grown films was broad and located at 425 nm. This luminescence reached to highest level after annealing at 600 °C. Maximum 10 min was required for full optical activation and prolonged annealing up to 4 h did not change the luminescence intensity. Because of deep levels, absorption band edge of as grown films was shifted to the lower energy which is 3.25 eV. Annealing above 800 °C reduced the PL intensity and this observation was correlated with the blue shift of band edge as the defects annealed out. Disappearing PL intensity and blue shift of band edge absorption after annealing at 950 °C was mainly attributed to the oxygen-related defects and partly to impurities that may be originated from oxalic acid. AFM results did not show any hexagonally ordered holes but uniformly distributed nanosized Al₂O₃ clusters that were clearly seen. XRD measurements on as grown Al₂O₃ showed only [1 1 0] direction of α phase. Debye–Scherer calculation for this line indicates that cluster size is 35.7 nm. XRD and AFM pictures suggest that nanocrystalline Al₂O₃ are embedded in amorphous Al₂O₃.     

Structural and optical properties of Er, Yb co-doped Y2O3 thin films

Thin Er³⁺, Yb³⁺ co-doped Y₂O₃ films were grown on (1 0 0) YAG substrates by pulsed laser deposition. Ceramic targets having different active ion concentration were used for ablation. The influence of the rare-earth content and oxygen pressure applied during the deposition on the structural, morphological and optical properties of the films were investigated. The films deposited at the lower pressure, 1 Pa, and at 1/10 Er to Yb doping ratio are highly textured along the (1 1 1) direction of the Y₂O₃ cubic phase. In addition to the crystalline structure, these films possess smoother surface compared to those prepared at the higher pressure, 10 Pa. All other films are polycrystalline, consisting of cubic and monoclinic phases of Y₂O₃. The rougher surface of the films produced at the higher-pressure leads to higher scattering losses and different behavior of the reflectivity spectra. Optical anisotropy in the films of less than 0.004 was measured regardless of the monoclinic structure obtained. Waveguide losses of about 1 dB/cm at 633 nm were obtained for the films produced at the lower oxygen pressure.     

Al2O3-Y2O3-ZrO2三相复合陶瓷的介电谱研究

采用传统的固相反应法,在1400–1500 ℃下烧结,制备得到Al₂O₃-Y₂O₃-ZrO₂三相复合陶瓷.样品的结构、形貌和电性能分别用X射线衍射(XRD)、扫描电子显微镜(SEM)及介电谱表征.XRD表明此三相复合体系无其他杂相,加入Y₂O₃及ZrO₂后使得Al₂O₃成瓷温度降低;SEM表明此体系晶粒直径为200–500 nm,并且样品随烧结温度的升高而变得更加致密,晶界更加清晰;介电损耗谱中出现峰值弛豫现象,根据Cole-Cole复阻抗谱得出其为非德拜弛豫. 关键词： 2O₃-Y₂O₃-ZrO₂三相陶瓷')" href="#">Al₂O₃-Y₂O₃-ZrO₂三相陶瓷 介电弛豫 阻抗谱 热导率     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Farinfrared absorption in Al2O3 and MgO

Far-infrared absorption measurements performed in Al₂O₃ and MgO between 300 and 1 500 K with a Fourier scanning interferometer are reported. A temperature analysis of results based on a phonon self-energy model allows to assign the absorption in this region to 2- and 3-phonon difference processes. The contributions of these processes are separated and discussed. In Al₂O₃, the frequency dependence of the absorption is also analyzed. A good overall agreement between theory and experiment is evidenced.