粘质沙雷氏菌脂肪酶的固定化及催化拆分反式3-(4’-甲氧苯基)缩水甘油酸甲酯

 对粘质沙雷氏菌脂肪酶进行了固定化研究,确定硅藻土和环氧树脂Eupergit C是较好的固定化载体. 固定化后酶的热稳定性、 pH稳定性及储存稳定性均明显提高. 以Eupergit C共价固定的脂肪酶,其操作稳定性比硅藻土吸附酶好,重复使用10批次后,剩余酶活力还有50%左右,戊二醛交联对Eupergit C固定化酶稳定性的提高没有明显效果,而硅藻土吸附酶经戊二醛交联后稳定性有所提高,经5批次反应后剩余酶活力还有50%. 使用交联后的硅藻土固定化酶(1 g, 200 U), 在两相搅拌反应器(工作体积200 ml, 甲苯∶水体积比=1)中对地尔硫卓手性前体(±)-反式3-(4’-甲氧苯基)缩水甘油酸甲酯((±)-MPGM)(有机相浓度为0.5 mol/L)进行了催化拆分,经5批次反应后,共得纯(2R,3S)-(-)-MPGM 18.6 g, 产品光学纯度(对映体过量)>99%, 总收率为37.2%.     

α，ω─二羧基聚乙二醇磁性毫微粒固定化碱性蛋白酶的研究

本文用共沉淀法制备了平均直径为３８４纳米的α，ω─二羧基聚乙二醇磁性毫微粒．碱性蛋白酶通过吸附交联法被固定于磁性毫微粒．研究了制备过程中的吸附时间、给酶量、戊二醛浓度、ｐＨ和离子强度对磁性固定化酶活力及酶固定化率的影响．比较了磁性蛋白酶磁性固定化酶与自由酶的酶学性质，磁性固定化酶的最适温度有改变，但热稳定性显著提高；磁性固定化酶的最适ｐＨ向酸性方向移动了１．０个ＰＨ单位。     

固定化乙酰胆碱酯酶的制备及其特性研究

本研究以期研制出能重复使用的固定化乙酰胆碱酯酶(AChE),为天然产物复杂体系中AchE抑制剂筛选新方法的发展奠定基础.以氨基化硅胶(APS-Si)微球为载体,戊二醛为交联剂对乙酰胆碱酯酶进行交联固定化,并研究了酶的最佳固定化条件和固定化酶的性质.结果表明,0.05 g氨基化硅胶微球载体,用戊二醛溶液活化6 h后,在给酶量5 U,28℃固定16 h条件下,得到固定化酶的活性最大.固定化酶在常温(20～40℃),以及较宽pH范围内(pH 6～10)均具有较高的活性,并且具有良好的保存稳定性和可重复利用率,为基于固定化靶酶亲和-色谱质谱联用分析快速筛选乙酰胆碱酯酶抑制剂新方法的发展奠定了基础.     

壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶及其性质

以具柔性亲水手臂的壳聚糖-精氨酸树脂为载体,用戊二醛交联胰凝乳蛋白酶,获得壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶. 最佳固定化条件为:m(酶)∶ m(载体)=20∶ 1 000、戊二醛体积分数为1.0%、pH=5.20、30 ℃交联60 min. 固定化酶活力达850 U/g,Km为1.83 mmol/L,比游离酶增大33.6%,比交联壳聚糖固定化酶低24.0%. 壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶水解时间进程曲线与游离酶基本一致,均在反应30 min达到最大速率,最适温度为70 ℃,比游离酶升高10 ℃;在75 ℃时的半衰期可达6.0 h,比游离酶提高约4.3倍;最适pH值为5.92,比游离酶向酸性偏移2pH单位. 4 ℃贮存半衰期为49 d.     

α,ω—二羧基聚乙二醇磁性毫微粒固定化碱性蛋白酶的研究

本文用共沉淀法制备了平均直径为３８４纳米的α，ω－二羧基聚乙二醇磁性毫微粒，碱性蛋白酶通过吸附交联法被固定于磁性毫微粒，研究了制备研究中的吸附时间，给酶量，戊二醛浓度，ｐＨ和离子强度对磁性固定化酶活力及酶固定化率的影响。比较了碱性蛋白酶磁性固定化酶与自由酶的酶学性质，磁性固定化酶的最适温度没有改变，但热稳定性显著使高；磁性固定化酶的最适ｐＨ向酸性方向移动了１．０个ｐＨ单位。     

黑曲霉脂肪酶的耦合固定化及特性

研究了吸附-絮凝耦合的方法固定脂肪酶的工艺条件.结果表明:在33℃下,用0.03mol/L的磷酸二氢钾?氢氧化钠缓冲液控制体系pH为7.0,酶与树脂(质量比1∶8)作用吸附1h后,用0.2mL絮凝剂聚丙烯酰胺(w(PAM)=0.5%)处理,得到活力较高的固定化脂肪酶.固定化酶最适pH9.0,最适温度为45℃,活力为405U/g,酶活回收率可以达到40%.固定化脂肪酶制备简便,可重复使用,稳定性较高.     

固定化木瓜蛋白酶的制备和性质研究

多孔硅球固定化木瓜蛋白酶具有热增活性 .本文在前文研究的基础上 ,用载体交联法制备了甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶 .考察了固定化pH值、戊二醛浓度和给酶量对固定化木瓜蛋白酶活力的影响 .研究了固定化木瓜蛋白酶的性质 ,特别是热稳定性和耐热性 ,并与溶液酶和多孔硅球固定化木瓜蛋白酶进行了比较 .所制得的甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶的最适反应温度均达到了 80℃ ;90℃温育 1h后固定化酶的活力保持在 95 %以上 ;70℃温育处理 5h和 6h后固定化酶的活力也仍能保持在 90 %以上 .固定化木瓜蛋白酶的热稳定性和耐热性得到了显著提高     

磁性纳米颗粒固定化细菌纤维素酶的活性和稳定性（英文）

在氨水溶液中进行Fe~(+2)和Fe~(+3)离子共沉淀并水热处理后制得磁性纳米颗粒Fe_3O_4,通过戊二醛活化将纤维素酶固定于其上.采用基于响应面法的Box-Behnken法(BBD)优化了制备条件,如磁性纳米颗粒浓度、戊二醛浓度、酶浓度和交联时间.BBD分析结果表明,用实验数据可合理调节二次模型.利用生成的基于统计数据的等高线评价了响应面的变化,以理解纳米颗粒和酶活性之间的关系.运用扫描电镜、X射线衍射和红外光谱表征了纳米颗粒上酶的尺寸、结构、形貌和结合情况.采用诸如pH值、温度、重复使用性和存储能力分析了固定化纤维素酶的活性和稳定性.发现固定后的纤维素酶表现出更好的稳定性和活性.     

海藻酸钙凝胶包埋乳酸氧化酶催化DL-乳酸生产丙酮酸

研究了用海藻酸钠包埋、戊二醛交联法固定耻垢分枝杆菌(Mycobacterium Srnegmatis)生成乳酸氧化酶的最佳条件,比较了原酶与固定化酶的酶学性质.将1mL酶液和1 mL质量分数为3%的海藻酸钠溶液的混合液,用注射器滴加到20 mL0.2 mol/L.的CaCl2溶液中,25℃静置固化2 h后,过滤洗涤,将同体转移至20 mL质量分数为0.2%戊二醛溶液中37℃交联2 h后,过滤、洗涤和干燥得到球状同定化酶.固定化酶的活力回收率为39.8%.酶学性质研究表明,此固定化酶的热稳定性较好,游离酶在65 ℃保温l h酶蛋白完全变性失活,而固定化酶在65℃保温1 h仍可保持86%的酶活力;其最适酶促反应温度可由37℃升至55℃,最适反应pH=7.4保持不变;在不加保护剂的条件下,4℃放置50 d后游离酶仅保持40%以上的酶活力,而固定化酶能保持80%以上的酶活力.该固定化乳酸氧化酶用于催化氧化DL-乳酸生产丙酮酸,3 h后丙酮酸产率可达75%,连续循环使用5次固定化酶活力仍保持85%.     

固定化葡萄糖氧化酶的制备及稳定性研究

选用自制的磁性纳米四氧化三铁为酶固定化的载体,通过交联法来固定葡萄糖氧化酶。通过对酶固定化过程中一系列因素的研究,确定出酶固定化的最佳工艺为:交联剂戊二醛与浓度为0.7 mg/mL酶液的体积比为1:4,固定化时间为0.5 h,固定化温度为室温(≤20 ℃),固定化所用缓冲液pH=7。采用比色法测定其酶活力。结果表明葡萄糖氧化酶经过固定化后,其酶活力较游离酶显著增加。固定化酶的热稳定性、酸碱稳定性、存储稳定性都有很大的提高。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.