草莓型SiO2/PMMA纳米复合微球的制备

在纳米二氧化硅水分散体系中,借助于碱性辅助单体1-乙烯基咪唑(1-VID)与未改性纳米二氧化硅表面羟基之间的酸-碱作用,通过1-VID与甲基丙烯酸甲酯(MMA)的自由基共聚合,制备了草莓型的SiO2/PMMA复合微球.整个反应过程中,纳米二氧化硅无需表面处理,体系中无需另外加入乳化剂或助乳化剂,微球表面吸附的纳米二氧化硅对颗粒起稳定作用.用动态光散射粒度分布仪测得复合微球粒径在120-330nm之间,热重分析结果表明,复合微球中二氧化硅含量介于15%-20%之间.透射电镜和扫描电镜显示所得复合微球具有草莓型结构,二氧化硅富集在表面.     

Preparation of SiO2/PMMA composite particles via conventional emulsion polymerization

A series of SiO₂/PMMA composite particles with different morphologies were prepared by conventional emulsion polymerization by the aid of acid–base interaction between the silanol groups of unmodified silica particles and the amino groups of 4‐vinylpyridine. In this approach, no surface treatment for nanosilica particles was required. The morphologies of composite particles, for example, multicore–shell, raspberry‐like, and conventional core–shell, could be controlled by modulating emulsifier content, monomer/silica ratio, silica size, and monomer feed method. The possible particle formation mechanisms were discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3807–3816, 2006     

Ultrasonically induced microemulsion polymerization of styrene

In this paper, ultrasonically induced microemulsion polymerization of styrene was successfully performed, possessing many merits such as high polymerization rate, the formation of small latex particles with a narrow size distribution, the absence of initiator and relatively low surfactant concentration. The monomer conversion reached 70% in 1 h, and the average diameter of polystyrene (PS) latex was about 30 nm which could be prepared with 3% surfactant (sodium dodecyl sulfate, SDS) concentration. The molecular weight of PS was around 10⁶ and the poly-distribution index was 1.06, indicating a very narrow distribution. Several influencing factors were investigated in detail, showing that ultrasonically induced microemulsion polymerization is a new route to prepare PS nanoparticles.     

Coating of multiwalled carbon nanotubes with polymer nanospheres through microemulsion polymerization

We report a simple and noncovalent method for coating multiwalled carbon nanotubes (MWCNTs) with polyaniline (PANI) nanospheres using a microemulsion polymerization method. In this method, aniline polymerization is performed with MWCNTs in the presence of sodium dodecyl sulfate (SDS), which serves as both a surfactant and a dopant. Morphological, structural, thermal, and electrical properties of MWCNT–PANI nanocomposites were analyzed. The TEM results of the nanocomposites prepared with surfactant reveal that 30–50-nm-diameter PANI nanospheres were coated on the surface of the MWCNTs. Composites prepared without surfactant were found to be in core–sheath-type cable structures. The conductivities of the nanocomposites synthesized through microemulsion polymerization were found to be one order of magnitude higher than both the conductivities of pure PANI and the composites prepared via in situ chemical polymerization without an assisting SDS surfactant. The mechanism for the formation of nanostructured composites is presented.     

PMMA/MMT nanocomposites prepared by one-step in situ intercalative solution polymerization

Poly(methylmetacrylate)/montmorillonite (PMMA)/(MMT) nanocomposites were prepared by one-step in situ intercalative solution polymerization involving simultaneous modification of MMT with quaternary ammonium salts (QAS), polymerization and polymer intercalation. Polymerization proceeded at 70 °C in a mixture of ethanol and water, whereas the nanocomposite was precipitated with only water. Four QAS’s with different alkyl chain lengths, as well as a QAS with an additional acrylic group, were used to study the influence of the type of quaternary ammonium salt on intercalation. The largest extent of intercalation was achieved in nanocomposites with the QAS having one long alkyl (C16) chain. The obtained PMMA/MMT intercalated nanocomposites exhibited a higher glass transition temperature, better thermal stability, and improved solvent resistance than the pure PMMA.     

Preparation of polyaniline-metal composite nanospheres by in situ microemulsion polymerization

Nanosized metal and polyaniline (PANi) composite spheres have been prepared via the polymerization of aniline using PdCl₂ or HAuCl₄ as the oxidant in a microemulsion system. The oxidization of aniline and the reduction of metal ion happened together during the reaction, yielding PANi and elemental metal simultaneously. The results of FTIR spectra suggested that the oxidation degree of PANi was affected by the initial ratio of metal ions to monomer in the microemulsion system. The PANi–metal nanospheres were characterized using X-ray photoelectron spectroscopy and the conductivity of the composite nanospheres was measured by conventional four-probe method. Scanning and transmission electron microscopy were used to show the morphology of the composites.     

Synthesis of polystyrene/SiO2 composite microparticles by dispersion polymerization in supercritical fluid

A novel synthetic route to prepare polystyrene/SiO₂ composite microparticles in supercritical carbon dioxide (scCO₂) is presented. Silica particles with the size of 130 nm which were surface-modified with 3-(trimethoxysilyl) propyl methacrylate were used as seeds in the dispersion polymerization of styrene in the presence of a polymeric stabilizer, poly(1,1-dihydroheptafluorobutyl methacrylate-co-diisopropylaminoethyl methacrylate) to produce dry composite particles. The transmission electron microscopy analysis revealed that the composite microspheres contained several silica particles.     

Synthesis and characterization of poly(EMA-co-HEA)/SiO2 nanohybrids

A series of silica-based organic-inorganic nanocomposites, which attempt to mimic the properties of mineralized matrix tissues from natural bone or dentin, have been prepared and characterized as potential candidates for the synthetic matrix of scaffolds for bone or dentin regeneration. The synthesis procedure consisted in the copolymerization of ethyl methacrylate (EMA) and hydroxyethyl acrylate (HEA) during the simultaneous acid-catalyzed sol-gel polymerization of tetraethoxysilane (TEOS) as a silica precursor, giving rise to poly(EMA-co-HEA)/SiO₂ nanohybrids with silica contents in the range of 0-30 wt%. Different structures of silica within the organic polymeric matrix were inferred from infrared spectroscopy, energy dispersive X-ray spectroscopy, thermogravimetry, pyrolysis, density assessments, solvent uptake and transmission electron microscopy. TEOS was efficiently hydrolyzed and condensed to silica during the sol-gel process in all cases, and presented a homogeneous distribution in the polymeric matrix, in the form of nanodomains either interdispersed or continuously interpenetrated with the organic network, depending on the silica content. Silica contents above 10% produced co-continuous interpenetrated structures where the silica network reinforces mechanically the organic matrix and at the same time confers bioactivity to the surfaces.     

Polymer–silica hybrids obtained by microemulsion polymerization

The styrene (St), butyl acrylate (BuA), and methyl methacrylate (MMA) polymerization in microemulsion in the presence of sodium dodecylsulfate is studied. This process is conducted in the presence of some comonomers having groups that can participate in sol–gel processes: 3(trimethyloxysilyl) propyl methacrylate (MPTS), triethoxy vinylsilane (VTES), and a comonomer with a sulfate group, styrene sodium sulfonate (StSO₃Na). It has been observed that stabile latexes are obtained by radical polymerization at pH = 7, followed by a sol–gel process in the presence of ammonia. Latex particles sizes and zeta potential grow with MTPS concentration and in StSO₃Na presence. VTES effect depends on its reactivity in St, MMA, and BuA copolymerization. Glass transition temperature and thermal decomposing temperature are influences by functional comonomer concentration and chemical structure. The Fourier transform infrared spectrum and inorganic residue growth after organic part thermal decomposition shows the presence of silica in obtained latexes.     

通过RAFT聚合制备SiO2/接枝共聚物纳米杂化粒子

以二氧化硅(SiO2)纳米粒子表面键接的二硫代苯甲酸酯作为可逆加成-断裂-链转移(RAFT)聚合反应的链转移剂, 在室温下引发苯乙烯和马来酸酐进行表面RAFT交替共聚反应, 制得了SiO2/苯乙烯-alt-马来酸酐杂化材料. 通过聚氧化乙烯(PEO)的羟基与马来酸酐的酯化反应, 将PEO接枝到SiO2纳米粒子的表面, 增加了硅粒子的生物相容性. 用FTIR, TGA和TEM对杂化材料的结构、组成和形貌进行了表征.     

石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂制备及其乙烯聚合性能

石墨烯自2004年发现以来,由于其独一无二的优异性迅速成为科学家们的研究热点.由于石墨烯具有极其优异的电学、力学和热学等性能,因此被广泛应用于高性能聚合物基复合材料的制备.众所周知,纳米填料在聚合物中的分散状态以及与基体间的界面作用是构筑高性能聚合物纳米复合材料的关键因素.由于石墨烯极易团聚,难以通过传统的熔融共混法制备均匀分散的石墨烯增强-聚烯烃纳米复合材料.另一方面,聚烯烃通常需要在较高温度下才能溶于部分有毒溶剂(如:三氯苯和二甲苯等),因此溶液共混法也不适用于聚烯烃-石墨烯纳米复合材料的制备.有鉴于此,本文开发了一种共沉积法制备石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂的路线.通过原位聚合直接制备出石墨烯均匀分散的聚烯烃/石墨烯纳米复合材料.考察了石墨烯的加入量对催化剂形态及其催化乙烯聚合行为的影响.当石墨烯加入量较低时,多个石墨烯片被包裹于较大的催化剂粒子中.随着石墨烯加入量的增加,催化剂趋向于在石墨烯表面聚集.继续增加石墨烯量将导致石墨烯包裹催化剂粒子,降低过渡金属钛的负载效率.通过三乙基铝活化后,所制备的催化剂具有非常高的乙烯催化活性,所生成的聚乙烯/石墨烯纳米复合材料复制了催化剂的片状结构.同时,通过对所制备的聚乙烯/石墨烯纳米复合材料进行电子显微镜和X射线衍射分析可知,石墨烯均匀分散于聚乙烯基体中,并且没有任何团聚现象发生.该复合材料的热重分析表明,仅加入非常少量的石墨烯就可以使其具有比纯聚乙烯更高的热稳定性,当石墨烯加入量为0.66 wt%时,其5 wt%热分解温度较纯聚乙烯升高了54°C.同时,所制备聚乙烯/石墨烯纳米复合材料具有更优异的机械性能.因此,本研究提供了一个简单高效的高性能聚烯烃/石墨烯纳米复合材料的制备方法.     

SiO2交联剂交联MMA聚合制备PMMA/SiO2纳米复合材料

用SiO2交联剂(SiO2HPA)交联甲基丙烯酸甲酯(MMA)自由基聚合制备PMMA SiO2纳米复合材料。采用两步法将可聚合乙烯基单体以化学键的形式键接到SiO2表面合成SiO2交联剂,首先利用过量的甲苯2,4二异氰酸酯(TDI)对SiO2纳米粒子表面进行化学修饰合成出表面带有高反应活性NCO基团的功能化SiO2粒子(SiO2TDI),SiO2TDI与丙烯酸羟丙酯(HPA)反应合成SiO2交联剂。系统研究了MMA单体与SiO2交联剂投料比及聚合时间对聚合反应的影响。此外,利用红外光谱(FT IR)、DSC、TGA、可见光光谱仪等实验手段对纳米复合材料进行了表征分析。结果表明,纳米SiO2粒子在复合材料中起着物理交联点和化学交联点作用,复合材料玻璃化转变温度(Tg)明显地高于其纯PMMA的玻璃化转变温度,随着纳米SiO2粒子含量的增加,复合材料玻璃化温度升高,而透明度明显降低。     

Surfactant stabilized nanopetals morphology of α-MnO2 prepared by microemulsion method

α-Manganese dioxide is synthesized in a microemulsion medium by a redox reaction between KMnO₄ and MnSO₄ in presence of sodium dodecyl sulphate as a surface active agent. The morphology of MnO₂ resembles nanopetals, which are spread parallel to the field. The material is further characterized by powder X-ray diffraction, energy dispersive analysis of X-ray, and Brunauer–Emmett–Teller surface area. Supercapacitance property of α-MnO₂ nanopetals is studied by cyclic voltammetry and galvanostatic charge–discharge cycling. High values of specific capacitance are obtained.     

Preparation of raspberry-like PMMA/SiO2 nanocomposite particles

Water-borne raspberry-like PMMA/SiO₂ nanocom-posite particles were prepared via free radical copolymerization of methyl methacrylate (MMA) with 1-vinylimidazole (1-VID) in the presence of ultrafine aqueous silica sols. The acid-base interaction between hydroxyl groups (acidic) of silica surfaces and amino groups (basic) of 1-VID was strong enough for promoting the formation of long-standing stable PMMA/SiO₂ nanocomposite particles when 10 mol% or more 1-VID as auxiliary monomer was used. The average particle sizes and the silica contents of the nanocomposite particles were in the ranges from 120–330 nm and 15%–20%, respectively. TEM and SEM observations indicated a raspberry-like morphology of the obtained nanocomposite particles. __________ Translated from Chemical Journal of Chinese Universities, 2005, 26(7) (in Chinese)     

Radiation-induced polymerization of methyl methacrylate in microemulsion with high monomer content

γ-Ray-induced polymerization of methyl methacrylate was conducted in a microemulsion stabilized by a mixture of sodium of 12-acryloxy-9-octadecenoic acid (AOA) and sodium dodecyl sulfate (SDS) with various weight ratios at room temperature. The experimental data showed that the mixture of AOA and SDS with a weight ratio 2 was an efficient surfactant system for the microemulsion containing 38.6 wt% MMA and 5.5 wt% surfactant. The effects of MMA concentration and dose rate on the polymerization kinetics and particle size are discussed.     

Novel polyester/SiO2 nanocomposite membranes: Synthesis,properties and morphological studies

In this paper, a new type of soluble polyester/silica (PE/SiO₂) hybrid was prepared by the ultrasonic irradiation process. The coupling agent γ-glycidyloxypropyltrimethoxysilane (GOTMS) was chosen to enhance the compatibility between the polyester (PE) and silica (SiO₂). Furthermore, the effects of the coupling agent on the morphologies and properties of the PE/SiO₂ hybrids were investigated using UV-vis and FT-IR spectroscopies and FE-SEM. The densities and solubilities of the PE/SiO₂ hybrids were also measured. The results show that the size of the silica particle was markedly reduced by the introduction of the coupling agent, which made the PE/SiO₂ hybrid films become transparent. Furthermore, thermal stability, residual solvent in the membrane film and structural ruination of membranes were analyzed by thermal gravimetric analysis (TGA). The effects of SiO₂ nanoparticles on the glass transition temperature (T_g) of the prepared nanocomposites were studied by differential scanning calorimetry (DSC). Moreover, their mechanical properties were also characterized. It can be observed that the Young's moduli (E) of the hybrid films increase linearly with the silica content. The results obtained from gas permeation experiments with a constant pressure setup showed that adding SiO₂ nanoparticles to the polymeric membrane structure increased the permeability of the membranes.     

Preparation of Al(OH)3/PMMA nanocomposites by emulsion polymerization

Al(OH)₃/PMMA nanocomposites were prepared by the emulsion polymerization of methyl methacrylate (MMA) in the presence of surface‐functionalized Al(OH)₃ particles. Nanosized Al(OH)₃ particles were previously functionalized with a silane coupling agent, 3‐(trimethoxysilyl) propyl methacrylate (γ‐MPS), which was confirmed by FT‐IR and XRF analysis. The average size of seed particles was around 70 nm, and the density of the coupling agent on the particles was calculated to be 8.9 µmol m^?2. The emulsion polymerization was attempted at relatively high solid content of 40–46 wt%. The ratio of the seed particles to MMA had a strong influence on the stability of latex as well as the morphology of composites. Nanocomposites where several PMMA nodules were attached on the surface of Al(OH)₃ core were produced with stable latex emulsion when the weight percents of Al(OH)₃ to MMA were below 20. In the case of higher ratio of 30%, however, the latexes became unstable with an aggregation, and the product morphology was in the shape of large composite. Thermogravimetric analysis showed an improved thermal stability of PMMA composites with the incorporation of Al(OH)₃ nanoparticles. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation of multihollow P(St-MAA) particles by sequence soap-free/soap emulsion polymerization and followed by stepwise alkali/acid posttreatment

The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The original latex particles with narrow size distribution were synthesized by a new sequence emulsifier-free/emulsifier emulsion copolymerization of styrene (St) and methacrylic acid (MAA). Results indicated that the pore size decreased and the pore number increased with the increase of SDBS amount, and the morphology of the posttreated latex particles was also significantly influenced by the introducing time of SDBS in the preparation of the original latex particles, and a suitable introducing time was 3 h of polymerization.     

PMMA/nano-SiO2纳米复合材料的制备和表征

PMMA/nano-SiO2纳米复合材料的制备和表征;二氧化硅;聚甲基丙烯酸甲酯;溶液聚合     

Surface Modification of Nano－SiO2 by Grafting PMMA／PBA

The surface of nano-SiO2 was modified by being encapsulated with hydroxy-propyl-methyl cellulose (HPMC), and then co-grafted with acrylates. The grafting conditions, such as pH of the medium, and initiator concentration have been studied. The modified nano-SiO2 particles were characterized by TEM, DSC and FT-IR spectra. TEM images show that the surface of the nano-particles has been successfully modified by a thick layer of film-like polymer in this way. The DSC results show that the decomposition temperature of modified nano-particles of SIO2 is 90 ℃ higher than that of grafted-on polymer. According to the FT-IR spectra, It is convinced that poly-methyl methacrylate ( PMMA ) and poly-acrylic butyl-ester ( PBA ) were co-grafted onto the surface of nano-SiO2.