声场中气泡群的动力学特性

以水为工作介质,考虑了液体的轻微可压缩性,研究了声场中气泡群的动力学特性,对单一型和混合型气泡群内微泡的初始半径、气泡的数目及声频率和声压对气泡动力学特性进行了数值研究．分析了各参数对气泡运动特性和气泡崩溃时所产生压力脉冲的影响．研究了单一型气泡群内气泡动力学的混沌特性,分析了气泡处于混沌特性下两次崩溃压力脉冲特征,结果表明：适合的参数有利于提高声空化处理效果．     

圆形破口附近气泡动态特性实验研究

以往对于壁面附近气泡动态特性的研究均是针对完整壁面进行的, 而对带破口壁面附近气泡运动特性的研究很少, 例如舰船结构在遭受药包爆炸冲击波作用后形成破口, 其仍可能会遭受随后生成气泡的二次打击, 破口的存在必定会影响爆炸生成气泡的动力学行为. 本文采用电火花气泡生成与观察实验装置, 对带有破口的壁面附近气泡脉动和射流特性进行研究.通过实验发现, 当气泡在破口同心位置生成时, 破口的存在会使气泡靠近破口一侧形成"腔吸现象", 并使气泡形成对射流. 在此基础上分析了破口大小和无量纲距离对破口附近气泡的影响规律, 最后讨论气泡在破口偏心位置生成时的运动特性, 结果发现破口附近气泡的二次打击威力随偏心距离的增加而增加, 文章旨在为不同边界附近气泡运动规律研究提供参考. 关键词： 气泡 实验 破口 射流     

利用声衰减反演气泡群分布的方法研究

通过测量含气泡水的声衰减反演气泡群参数是获取水中气泡分布的重要方法,但是经典方法忽略了较高浓度气泡水中的强频散特性和气泡振动参数的改变,导致反演较高浓度气泡群分布时会产生巨大误差.为解决这个问题,本文基于等效媒质理论建立起了声衰减和相速度的联系,并考虑了含气泡水平均量对气泡阻尼系数和共振频率的影响.在此基础上,通过将反...     

不同沙粒底面下气泡脉动特性实验研究

通过高速摄影系统对电火花气泡与不同沙粒底面间的相互作用进行了实验研究,并改变气泡与沙粒底面之间的距离.实验结果表明:气泡在与沙粒底面的相互作用中会产生两种明显不同的现象,即形成与近刚性壁面类似的气泡射流以及“蘑菇状”气泡,“蘑菇状”气泡撕裂形成两个气泡,随后产生两个反方向的沿轴线方向的射流.沙粒底面边界具有刚性与弹性两种特征.另外,随着气泡与沙粒底面之间的距离d的增大,气泡脉动周期先增大然后减小,存在气泡脉动周期峰值.对于不同的沙粒底面边界,出现气泡脉动周期峰值的距离d随着沙底粒径的增大而越小.     

混合工质过冷核化沸腾气泡行为特性

本文采用控制热流密度方式对乙醇和水二元混合物在直径0．1 mm铂丝上过冷沸腾核化进行可视化实验观察, 分析不同混合比、热流密度下过冷沸腾核化实验现象。实验证明,小气泡射流是混合工质沸腾换热中主要的换热形式,并且其形态具有多样化,如连续射流、间断射流、离散射流、非常规射流、分叉射流等。     

水中上浮气泡动态特性研究

针对水中的上浮气泡,计入表面张力的作用,然后将气泡边界层内黏性效应分为法向和切向两部分,其中附加法向黏性应力通过Young-Laplace关系考虑;附加切向黏性力是基于黏性耗散能量等效原理,引入黏性修正压力代替.首先建立了轴对称和三维上浮气泡边界元模型,将数值结果与理论值和实验值进行对比分析,有良好的符合度,验证了数值模型的有效性;然后针对毫米量级上浮气泡的平衡速度与形态,讨论了气泡初始条件、表面张力和黏性对气泡上浮过程中动力学行为的影响;最后,提出了一种处理三维上浮气泡融合的数值方法,计算结果与实验现象符合良好,并且能够反映气泡融合后的复杂现象细节.     

不同类型气泡组成的混合泡群声空化特性

声空化实验中经常观察到由许多空化气泡组成的各种泡群结构.本文利用气泡群及群内任一气泡的Rayleigh-Plesset方程并结合van der Waals型过程方程,研究了不同类型气泡组成的混合泡群中的气泡半径、泡内温度和群内压力脉冲变化规律,得到以下结果:相同尺寸相同气体气泡和相同尺寸不同气体气泡组成的两种泡群中气泡所含的不同气体对泡内温度有较明显的影响,但对气泡半径变化和群内压力脉冲峰值的影响较小;不同尺寸相同气体气泡和不同尺寸不同气体气泡组成的两种混合泡群中,随着大气泡数的增多,大小气泡内温度开始快速下降,之后大泡内温度逐渐趋近于纯大气泡组成泡群的泡内温度,小泡内温度逐渐趋近于许多大泡辐射作用下的单一小气泡泡内温度;气泡崩溃时产生的压力脉冲峰值,先急剧减小到拐点,之后平稳增加并逐渐趋近于纯氩气大气泡和纯氦气大气泡组成泡群内的压力脉冲峰值;群内大气泡数占比对泡群空化特性有重要影响,只有大气泡数占比达到一定值后泡群中才能出现不同尺寸气泡同时崩溃的现象.     

微通道气液同向流动中气泡射流特性

利用高速CCD成像技术,本文研究了梯形横截面微通道内的气泡喷射流动.通过调节同向流动时空气和水流量,研究了气泡形成的大小和频率等变化特性;以及微通道内的流型变化.实验结果表明,气泡喷射频率随空气流量的增加而增大,同时随水流量的增加而上升,且上升幅度渐趋平缓.     

气泡线性振动时近海面气泡群的声散射

海洋中的不同成因的气泡群是常见的水下声学目标及声呐混响源,因此对水下气泡群进行声学建模意义重大。利用有效媒质理论描述气泡群内部的相速度及声衰减变化,并考虑到海洋中气泡群往往产生于不同界面附近,进一步利用球面波叠加原理描述海面对气泡群散射声波的再辐射,导出了平海面作用下气泡群声散射截面的一般表达式,建立了其声散射模型,研究了单一尺寸及混合尺寸气泡群的声学特性。数值分析表明,气泡群的谐振频率会随其半径或孔隙率增加而降低;由于海面的存在,气泡群声散射截面会随频率进行周期性变化,且随气泡群远离海面,这一变化逐渐加剧。此外,若气泡的黏滞阻尼项在全部阻尼项中占比较高,气泡群声散射强度会在谐振频率附近存在起伏振荡。该模型可为近海面鱼群、气泡羽流及海底泄漏的甲烷气体的声学建模提供一定的理论基础。     

球状泡群内气泡的耦合振动

振动气泡形成辐射场影响其他气泡的运动, 故多气泡体系中气泡处于耦合振动状态. 本文在气泡群振动模型的基础上, 考虑气泡间耦合振动的影响, 得到了均匀球状泡群内振动气泡的动力学方程, 以此为基础分析了气泡的非线性声响应特征. 气泡间的耦合振动增加了系统对每个气泡的约束, 降低了气泡的自然共振频率, 增强了气泡的非线性声响应. 随着气泡数密度的增加, 振动气泡受到的抑制增强; 增加液体静压力同样可抑制泡群内气泡的振动, 且存在静压力敏感区(1–2 atm, 1 atm=1.01325×10⁵ Pa); 驱动声波对气泡振动影响很大, 随着声波频率的增加, 能够形成空化影响的气泡尺度范围变窄. 在同样的声条件、泡群尺寸以及气泡内外环境下, 初始半径小于5 μm 的气泡具有较强的声响应. 气泡耦合振动会削弱单个气泡的空化影响, 但可延长多气泡系统空化泡崩溃发生的时间间隔和增大作用范围, 整体空化效应增强.     

The dynamics of cavitation bubbles in a sealed vessel

A model of cavitation bubbles is derived in liquid confined in an elastic sealed vessel driven by ultrasound. In this model, an assumption that the pressure acting on the sealed vessel due to bubble pulsations is proportional to total volume change of bubbles is made. Numerical simulations are carried out for a single bubble and for bubbles. The results show that the pulsation of a single bubble can be suppressed to a large extent in sealed vessel, and that of two matched bubbles with same ambient radius can be further suppressed. However, when two mismatched bubbles have the same ambient radii, an interesting breathing phenomenon takes place, where one bubble pulsates inversely with the other one. Due to this breathing phenomenon the suppression effect becomes weak, so the maximum radii of two mismatched bubbles can be larger than that of a single bubble or that of two matched bubbles in sealed vessel. Besides that, for two mismatched bubbles with different ambient radii, the small one in sealed vessel under some certain parameters can pulsate as strong as or even stronger than that of a single bubble in an open vessel.     

Current-driven dynamics of skyrmion bubbles in achiral uniaxial magnets

We report dynamics of skyrmion bubbles driven by spin-transfer torque in achiral ferromagnetic nanostripes using micromagnetic simulations. In a three-dimensional uniaxial ferromagnet with a quality factor that is smaller than 1, the skyrmion bubble is forced to stay at the central nanostripe by a repulsive force from the geometry border. The coherent motion of skyrmion bubbles in the nanostripe can be realized by increasing the quality factor to ～ 3.8. Our results should propel the design for future spintronic devices such as artificial neural computing and racetrack memory based on dipole-stabilized skyrmion bubbles.     

The interaction between multiple bubbles and the free surface

The flow is assumed to be potential, and a boundary integral method is used to solve the Laplace equation for the velocity potential to investigate the shape and the position of the bubble. A 3D code to study the bubble dynamics is developed, and the calculation results agree well with the experimental data. Numerical analyses are carried out for the interaction between multiple bubbles near the free surface including in-phase and out-of-phase bubbles. The calculation result shows that the bubble period increases with the decrease of the distance between bubble centres because of the depression effect between multiple bubbles. The depression has no relationship with the free surface and it is more apparent for out-of-phase bubbles. There are great differences in dynamic behaviour between the in-phase bubbles and the out-of-phase bubbles due to the depression effect. Furthermore, the interaction among eight bubbles is simulated with a three-dlmensional model, and the evolving process and the relevant physical phenomena are presented. These phenomena can give a reference to the future work on the power of bubbles induced by multiple charges exploding simultaneously or continuously.     

激波与SF6球形气泡相互作用的数值研究

本文基于大涡模拟方法, 采用高阶精度格式对平面入射激波以及不同反射距离条件下的反射激波与SF₆重气泡相互作用过程进行了三维数值模拟. 数值结果清晰地显示了SF₆重气泡在激波作用下诱导Richtmyer-Meshkov不稳定性过程, 揭示了入射激波以及反射激波在气泡界面聚焦诱导射流的过程, 详细分析了不同反射距离条件下反射激波与SF₆重气泡作用过程及流场结构.     

双泡模型共振频率的超声空化动力学研究

该研究旨在研究双泡模型的自然共振频率对超声空化的影响,通过理论计算研究了自然共振频率的影响因素,以及单频超声和双频超声与自然共振频率的关系。研究结果表明：气泡初始半径是影响自然共振频率的主要因素;低频驱动下的非线性波动程度会比高频的更加剧烈,当驱动频率等于气泡自然共振频率时,超声空化的效果更好;双频超声取气泡自然共振频率时超声空化效果远远优于单频超声驱动。该研究在超声医学和理解超声空化特性方面有着重要的意义。     

Vortex dynamics of collapsing bubbles: Impact on the boundary layer measured by chronoamperometry

Cavitation bubbles collapsing in the vicinity to a solid substrate induce intense micro-convection at the solid. Here we study the transient near-wall flows generated by single collapsing bubbles by chronoamperometric measurements synchronously coupled with high-speed imaging. The individual bubbles are created at confined positions by a focused laser pulse. They reach a maximum expansion radius of approximately 425 μm. Several stand-off distances to the flat solid boundary are investigated and all distances are chosen sufficiently large that no gas phase of the expanding and collapsing bubble touches the solid directly. With a microelectrode embedded into the substrate, the time-resolved perturbations in the liquid shear layer are probed by means of a chronoamperometric technique. The measurements of electric current are synchronized with high-speed imaging of the bubble dynamics. The perturbations of the near-wall layer are found to result mainly from ring vortices created by the jetting bubble. Other bubble induced flows, such as the jet and flows following the radial bubble oscillations are perceptible with this technique, but show a minor influence at the stand-off distances investigated.     

Investigations on dynamics of interacting cavitation bubbles in strong acoustic fields

Given its importance to the dynamics of cavitation bubbles, the mutual interaction between bubbles was carefully investigated in this work. The cavitation noises emitted in different sonication conditions were recorded to study the dynamical behavior of the bubbles. The frequency spectra of the noises suggest that the dispersing state of the bubbles severely influence the oscillations of bubbles, and that the nonlinear feature of the dynamics of cavitation bubbles, imposed by the mutual bubble-bubble interaction, gradually develops with the decrease of the dispersing height. Theoretical analysis shows that the size difference between the interacting bubbles should be responsible for the increase of nonlinearity of the oscillation, and that the decrease of the distance between them could effectively enhance the nonlinear feature of the oscillation of the bubble, both of which agree well with the experimental observation.     

Statics and dynamics of adhesion between two soap bubbles

An original set-up is used to study the adhesive properties of two hemispherical soap bubbles put into contact. The contact angle at the line connecting the three films is extracted by image analysis of the bubbles profiles. After the initial contact, the angle rapidly reaches a static value slightly larger than the standard 120^° angle expected from Plateau rule. This deviation is consistent with previous experimental and theoretical studies: it can be quantitatively predicted by taking into account the finite size of the Plateau border (the liquid volume trapped at the vertex) in the free energy minimization. The visco-elastic adhesion properties of the bubbles are further explored by measuring the deviation Δθ_d(t) of the contact angle from the static value as the distance between the two bubbles supports is sinusoidally modulated. It is found to linearly increase with Δr _c/r _c , where r_c is the radius of the central film and Δr _c the amplitude of modulation of this length induced by the displacement of the supports. The in-phase and out-of-phase components of Δθ_d(t) with the imposed modulation frequency are systematically probed, which reveals a transition from a viscous to an elastic response of the system with a crossover pulsation of the order 1rad · s^-1. Independent interfacial rheological measurements, obtained from an oscillating bubble experiment, allow us to develop a model of dynamic adhesion which is confronted to our experimental results. The relevance of such adhesive dynamic properties to the rheology of foams is briefly discussed using a perturbative approach to the Princen 2D model of foams.     

Experimental investigations of three laser-induced synchronized bubbles

Herein, we investigated experimentally the dynamics of three laser-induced, same-sized, symmetrically aligned, and synchronized bubbles. Three synchronized laser beams split from the same beam using a Diffractive Optical Element splitter were focused on water, and then we obtained three bubbles. Another nanosecond laser pulse was used to probe the bubbles to obtain shadowgraphs. The exact delay of the excited and detected light was controlled using a delay generator. The results revealed that the maximum volumes of bubbles in arrays decrease as the normalized distance falls, while the lifetimes and translation increase. It was explained by the interaction between the acoustic radiation of bubbles and the surrounding bubbles. The shrinkage of linear bubble arrays exists an anomaly. The center bubbles were stretched, to ellipsoid, stick, even fractured, by the peripheral bubbles. The closer they are, the more distinct is the above phenomenon. However, when the normalized distance was sufficiently small, instead of being stretched, the center bubbles were compressed to disk shape and thus shrank with the whole array. Finally, the dependence of the distance on the energy transfer of the bubble system is also discussed.