单摄像机立体视觉测量系统的高精度变焦标定技术

针对现有用于光学测量的双目变焦系统标定方法难度大、测量精度受限于两摄像机内参一致性等问题。提出一种基于单摄像机的平行双目立体视觉系统实现及其高精度变焦标定方法。方法基于三角测量原理采集图像,利用高精度位移台驱动单摄像机进行平移以保证基线精度;求解离散焦距下的预标定结果并利用BP神经网络模型对其进行拟合,以实现任意焦距下系统内外参数动态估计。实验结果表明,系统预标定的重投影误差小于0.1664 pixel,变焦后图像畸变校正平均误差为0.0982 pixel,立体视觉测量尺寸绝对误差小于0.05mm。方法能弥补传统变焦标定方法的不足,消除双目内参不一致引入的误差,提高视觉系统的测量精度。     

基于神经网络的视觉系统标定方法

为了解决摄像机标定存在的若干问题 ,根据立体视觉原理 ,提出了基于神经网络的双目视觉系统标定方法。通过对双目摄像机的有效视场分析 ,确定了一次测量面积 ,并把像对视差作为网络输入 ,建立空间点世界坐标与图像坐标非线性映射关系 ,使系统不经过复杂的摄像机内外参数标定 ,就能直接提取物体的三维信息 ,增加了系统的灵活性。实验证明 ,该方法有效可行     

基于同心圆合成图像匹配的双目视觉标定

分析了双目视觉传感器的数学模型,提出了一种基于同心圆合成图像匹配的双目视觉传感器的标定方法。在测量范围内任意多次摆放同心圆靶标,由两台摄像机拍摄靶标图像。根据摄像机模型与已知同心圆在靶标坐标系上的位置关系,构造合成图像,将合成图像与观测图像进行相似度匹配,通过优化定位得到靶标上每个圆的圆心点图像坐标。利用左右图像对应的圆心图像坐标和双目视觉的约束关系,对双目视觉传感器参数进行非线性优化,并得到最优解。所提出的标定方法是在张正友方法的理论基础上,利用了图像的整体性进行的优化。实验结果表明,该方法提高了标定精度。     

基于傅里叶条纹分析的多摄像机标定方法

提出一种新的摄像机标定方法,该方法基于2D共面参照物摄像机标定方法和傅里叶条纹分析方法.将已知相位分布的平面二维正弦灰度调制条纹图作为平面标定靶,通过傅里叶条纹分析方法计算出两个截断正交相位分布,利用截断正交相位分布并结合二维正弦条纹图特点提取相应的图像特征点,建立像素坐标与2D平面坐标的对应关系.将该二维平面靶在摄像机成像空间中放置不同的位置,并完成相应的特征点提取,根据2D共面参照物摄像机标定方法即可完成摄像机标定.该方法利用平面相位测量的高准确度来提高标定特征点的提取准确度,从而提高标定准确度.实验对双摄像机系统进行了标定,标定后该系统对标定靶进行测量,标准偏差达到0.010 mm.     

基于转轴参数的多自由度双目视觉系统标定

多自由度双目立体视觉系统可以解决传统双目立体视觉视场区域小的问题。避免双目摄像机每转动一个角度都需要重新标定外参数,提出了一种基于转轴参数的标定方法。只需标定出初始位置时双目摄像机的内外参数,使摄像机绕转轴旋转,根据单应性原理测量摄像机与标定模板的位姿关系,确定转轴方向矢量与轴上点坐标。最终利用Rodrigues旋转矩阵确定旋转已知角度后双目摄像机的外参数,实现多自由度双目系统的标定。实验结果表明,提出的方法能准确测量转轴参数,完成多自由度双目立体视觉系统的快速标定,提高系统的工作效率。     

摄像机的一种主动视觉标定方法

提出了一种快速高精度的摄像机主动视觉标定方法,建立了摄像机模型并详细分析了其各项参数的求解算法。标定时,令摄像机作一组二维的平移运动,采集圆孔靶标件的图像并计算圆心的像点坐标,同时记录摄像机的移动距离,得到标定所需的特征点。利用这些特征点计算摄像机标定参数,标定精度可达到0.005 mm。利用该方法定制的标定模块实现了摄像机的自动标定。该方法对摄像机运动的限制条件较少,并基本实现了摄像机模型参数的线性求解,为主动视觉系统的摄像机标定提供了一种有效的解决方案。     

“网格式平行线法”在螺纹参数测量中的应用

在计算机视觉理论基础上发展起来的视觉检测(vision inspection)技术具有非接触、速度快、精度适中、可实现在线等优点，已广泛地应用于工业产品的在线检测。在计算机视觉检测技术中CCD摄像机是一个最关键的器件，其参数是否准确决定了检测的精度。所以，摄像机标定是视觉检测技术中最基本的也是最重要的一步。在比较其他标定方法的基础上，为了解决传统标定方法对螺纹图像测量系统所带来的一系列问题，采用了一种新的图像测量系统的标定方法——网格式平行线标定方法，该方法运用了CCD亚像素细分技术及调焦技术，可直接得到纵横2个方向的像素，经过理论分析及实验结果均表明，采用该方法具有标定简单、精度高、重复性好等优点，是一种较好的螺纹图像测量系统标定方法。     

基于三线结构光的相机平面标定方法研究

相机标定技术是结构光三维视觉测量的关键技术之一,结构光系统的相机标定的精度对三维测量的精度有很大影响。首先对三线结构光系统图的相机标定方法进行了分析,简单介绍了工业相机成像的几何模型及标定的原理;其次利用Harris角点检测方法提取特征点坐标,并选用了BP神经网络来校正工业相机的畸变模型,以提高标定算法的优化速度和标定精度;最后采用张正友的平面标定法对校正后的摄像机模型进行标定实验,由实验结果知,该方法具有一定的准确性和有效性,在一定误差范围内,基于神经网络畸变校正的张正友相机标定能够有效提高视觉检测的精度。     

基于光学参考棒的立体视觉测量系统现场标定技术

为实现大空间复杂工件的准确测量,精确标定立体视觉系统变得越来越重要。为了克服传统立体摄像机标定过程繁复、户外实现困难的弱点,提出了一种基于光学参考棒的灵活、有效的立体视觉测量系统标定技术。参考棒水平和深度方向各有三个距离已知的红外LED作为特征点。通过在测量范围内的不同位置和方位移动光学参考棒,两像机同时捕获参考棒上特征点的图像。基于匹配的特征像点以及对极线约束,利用线性算法和Levenberg-Marquardt(LM)迭代算法快速地标定立体视觉测量系统。两像机之间平移量的比例因子由参考棒上特征点间的已知距离确定。参量标定过程中,自动地控制光强,优化曝光时间,使不同位置处光点图像的强度均一致,可以获得高的信噪比,提高标定精度。实验结果表明,该方法灵活、有效,在线标定能达到很高的精度,将现场标定过程应用到实际的大空间三维测量系统中,测量最大误差为0.18 mm。     

基于点阵标定板的视觉测量系统的标定方法EI北大核心CSCD

在应用机器视觉技术进行测量时,测量系统的像素当量、系统误差和光源强度等因素均会对测量精度造成影响,因此必须对像素当量和系统误差进行标定,并分析光源强度对工件图像边缘位置的影响。提出一种基于点阵标定板的视觉测量系统综合标定方法,在提取标定圆圆心坐标的基础上,计算圆心距物理尺寸和像素尺寸的比值,得到像素当量;建立圆心实际坐标和理论坐标的二元三次误差模型,并利用最小二乘法拟合求解误差模型系数;通过确定光源强度引起的图像边缘位置误差补偿量,实现测量系统的综合标定。实验结果表明,该方法可以有效提高系统的测量精度。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.