Renewable Ceramic (TiN) Ring Electrode in Stripping Voltammetry. Determination of Pb(II) Without Removal of Oxygen

Characteristic features of the process of Pb(II) reduction and oxidation at a renewable ceramic ring electrode (RCRE) were studied by stripping voltammetry. The main constituents of the RCRE are: a specially constructed TiN ring electrode, a silver sheet used as silver counter/quasi‐reference electrode and a silicon O‐ring are fastened together in a polypropylene body. The renovation of this electrode is carried out through mechanical removal of solid contaminants and electrochemical activation in the electrolyte which fills the RCRE body. The optimal measurement conditions, composition of supporting electrolyte and procedures of the electrode activation were selected. The measurements were carried out from nondeaerated solutions. As shown on selected examples, RCRE exhibits good performance in underpotential deposition stripping voltammetry (UPD‐SV) applied for the determination of lead(II) in synthetic solutions with and without surfactants and in certified reference materials. The peak current is proportional to the concentration of lead(II) over the range 2×10^?9–1×10^?7 mol L^?1, with a 3σ detection limit of 1×10^?9 mol L^?1 with an accumulation time of 30 s. The obtained results showed good reproducibility, (RSD=2–5%; n=5) and reliability.     

Influence of the degree of surface oxidation of polycrystalline Rh electrodes on the underpotential deposition of Cu

The underpotential deposition of copper onto polycrystalline rhodium was studied as a function of the degree of oxidation of the electrode surface in acidic media using potentiodynamic techniques. Surface oxidation of the rhodium electrode was carried out using a triangular sweep potential between E _L (lower limit) and E _U (upper limit: 0.94≤E _U≤1.4 V). Cu electrodeposition was performed at the same time as the total or partial reduction of the oxidized species. The surface oxides produced at E _U≤1.09 V were completely reduced during Cu electrodeposition. In this case, the potentiodynamic I-E patterns for oxidative dissolution of Cu were characterized by three anodic peaks located at 0.41 V (peak I), 0.47 V (peak II) and 0.59 V (peak III) and the coverage degree by Cu, θ_Cu, was on the order of a monolayer. Surface oxides produced at E _U>1.09 V were partially reduced during the copper electrodeposition. In this case, the I-E profiles exhibited only two anodic peaks (II and III) and θ_Cu was <1. The Rh-oxygen species that remain on the electrode surface block the active sites of lower energy and modify the binding energy of strongly adsorbed Cu. Electronic Publication     

Underpotential deposition of Cu on partially oxidized Rh electrodes

The underpotential deposition (UPD) of copper on partially oxidized rhodium electrodes was studied in acid medium using potentiodynamic techniques. The process was analyzed as a function of the potential and time of deposition. The potentiodynamic I-E patterns for the oxidative dissolution of Cu provide evidence for the existence of a chemical reaction between Cu and oxygen existing on the electrode surface. Redistribution of the active sites is also possible when appreciable quantities of oxidized species are simultaneously reduced by the UPD process. The partially oxidized rhodium electrodes were prepared by cyclic voltammetry and anodic polarization. The later method provided the most oxidized surfaces, but, even in this case, the degree of oxygen surface coverage was lower than that corresponding to a monolayer. Received: 11 July 1997 / Accepted: 10 February 1998     

Voltammetric behavior and trace determination of Pb at a mercury-free screen-printed silver electrode

Screen-printed silver electrodes (AgSPEs), without chemical modification, has been investigated as disposable sensors for the measurement of trace levels of Pb²⁺. Potential segment analysis indicates that the formation of underpotential and bulk depositions of Pb is not strongly coupled on the AgSPE. The possibility of determining Pb²⁺ at trace levels using the reversible underpotential deposition peak was examined by square-wave anodic stripping voltammetry without removal of oxygen. Under the optimized analytical conditions, the obtained sensitivity, linearity, and detection limit are 0.355 μA/ppb, 5-80 ppb (r=0.9992), and 0.46 ppb (S/N=3), respectively. The electrode is quite stable for repetitive measurements. The interference effect was thoroughly studied with various metals and no significant change in current was found in the determination of 5 ppb Pb²⁺. The practical applications were demonstrated to measure trace Pb²⁺ in natural waters.     

Adsorption behavior of Pb(II) on montmorillonite

The present work investigated the adsorption and desorption behaviors of Pb(II) on montmorillonite. The adsorption experiments were carried out using batch process. The results show that the adsorption is dependent on the pH value of the medium, and the uptake of Pb(II) increases with the pH increasing in the pH range of 2.0–10.0. The adsorption kinetics is in better agreement with pseudo-second order kinetics, and the adsorption data is a good fit with Langmuir isotherm. The presence of EDTA may result in a decrease of the amount of Pb(II) adsorbed. The presence of electrolyte and EDTA may enhance the desorption of Pb(II) ions adsorbed. The adsorption mechanism of Pb(II) on montmorillonite may be explained in two aspects: the chemical binding between Pb(II) ions and surface hydroxyl groups; and the electrostatic binding between Pb(II) ions and the permanent negatively charged sites of montmorillonite.     

Embedded atom method study of Cu deposition on Ag(111)

A new model is applied to the study of Cu deposition on Ag(111), It links elements from the embedded atom model and Monte Carlo simulations. In agreement with the experiment, the present results favor overpotential upon underpotential deposition. A diffusion coefficient of 1.93 × 10⁻⁶ cm² s⁻¹ is estimated for the system. The predicted structure of the adsorbed monolayer is more compact than the electrochemical observation, a fact which may be due to some simplifications of the model like neglecting the solvent and anion effects or the nature of the potentials employed.     

火焰原子吸收法测定胃乃安胶囊中铜铅含量

采用干灰化法处理样品，火焰原子吸收光谱法测定胃乃安胶囊中铜、铅含量，用氚灯背景校正，有效地消除了基体干扰，方法的检出限为Ｃｕ：０．０２３ｍｇ／Ｌ，ｐｂ：０．０７０ｍｇ／Ｌ，ＲＳＤ在２．９％～５．６％之间，回收率分别为Ｃｕ：９３％～１０３．６％；ｐｂ：８８．２％～９５．０％。     

Adsorptive accumulation of Cd(II), Co(II), Cu(II), Pb(II), and Ni(II) from water on montmorillonite: influence of acid activation

The present work investigates the influence of acid activation of montmorillonite on adsorption of Cd(II), Co(II), Cu(II), Ni(II), and Pb(II) from aqueous medium and comparison of the adsorption capacities with those on parent montmorillonite. The clay-metal interactions were studied under different conditions of pH, concentration of metal ions, amount of clay, interaction time, and temperature. The interactions were dependent on pH and the uptake was controlled by the amount of clay and the initial concentration of the metal ions. The adsorption capacity of acid-activated montmorillonite increases for all the metal ions. The interactions were adsorptive in nature and relatively fast and the rate processes more akin to the second-order kinetics. The adsorption data fitted both Langmuir and Freundlich isotherms, indicating that strong forces were responsible for the interactions at energetically nonuniform sites. The Langmuir monolayer capacity of the acid-activated montmorillonite is more than that of the parent montmorillonite (Cd(II): 32.7 and 33.2 mg/g; Co(II): 28.6 and 29.7 mg/g; Cu(II): 31.8 and 32.3 mg/g; Pb(II): 33.0 and 34.0 mg/g; and Ni(II): 28.4 and 29.5 mg/g for montmorillonite and acid-activated montmorillonite, respectively). The thermodynamics of the rate processes showed the adsorption of Co(II), Pb(II), and Ni(II) to be exothermic, accompanied by decreases in entropy and Gibbs free energy, while the adsorption of Cd(II) and Cu(II) was endothermic, with an increase in entropy and an appreciable decrease in Gibbs free energy. The results have established the potential use for montmorillonite and its acid-activated form as adsorbents for Cd(II), Co(II), Cu(II), Ni(II), and Pb(II) ions from aqueous media.     

Phase Formation Studies of Lead(II) Copper(II) Oxotellurates: The Crystal Structures of Dimorphic PbCuTeO5, PbCuTe2O6, and [Pb2Cu2(Te4O11)](NO3)2

Two modifications of the oxotellurate(VI) PbCuTeO₅ were isolated as single crystals from product mixtures obtained from solid state reactions, whereas single crystals of the oxotellurates(IV) PbCuTe₂O₆ and [Pb₂Cu₂(Te₄O₁₁)](NO₃)₂ were grown under hydrothermal conditions. The crystal structures of all compounds comprise of characteristic coordination polyhedra, viz. nearly square [CuO₄] plaquettes for divalent copper, octahedral [TeO₆] units for hexavalent tellurium, trigonal‐pyramidal [TeO₃] and bisphenoidal [TeO₄] groups for tetravalent tellurium, and distorted [PbO_x] polyhedra for divalent lead. PbCuTeO₅ is dimorphic and crystallizes in a monoclinic and a triclinic modification, related by a translationengleiche group‐subgroup relation of index 2. PbCuTe₂O₆ represents the ideal composition of the rare mineral choloalite. The characteristic feature of the crystal structure of [Pb₂Cu₂(Te₄O₁₁)](NO₃)₂ is its layered set‐up, comprised of cationic [Pb₂Cu₂(Te₄O₁₁)]²⁺ ribbons (width approximately 6.7 Å) sandwiched between nitrate anions that are only weakly bound to the cationic layers.     

Effects of underpotentially deposited TI and Pb submonolayers on the surface-enhanced Raman scattering (SERS) from pyridine at Ag electrodes

SERS from pyridine on an Ag electrode is almost completely quenched by underpotential deposition of TI to a surface coverage of ≈ 3%. Removal of TI by anodic stripping does not restore the original SERS intensity. These results suggest that only a small fraction of adsorbed pyridine molecules is SERS active, and TI is specifically deposited on such a SERS active site, which then undergoes irreversible destruction. Pb appears to be non-specifically deposited on the Ag surface, but exhibits a similar irreversible quenching of SERS.     

羧甲基壳聚糖对铅离子的吸附性能研究

本文研究羧甲基壳聚糖对Pb^2 的吸附作用,探讨反应时间,离子强度,溶液的PH值、羧甲基取代度,温度等因素对吸附性能的影响,结果表明羧基是吸附Pb^2 的主要活性基团,羧甲基壳聚糖对Pb^2 的饱和吸附量为3．1083mmol/g,吸附Pb^2 的能力比壳聚糖,水溶性低聚壳聚糖强。     

Adsorption of lead(II) and copper(II) on activated carbon by complexation with surface functional groups

The adsorption of lead(II) and copper(II) on an activated carbon (Filtrasorb 300, Chemviron) was characterized assuming that it takes place by formation of complexes with functional groups, present in the activated carbon. Their concentration and conditional adsorption coefficients were determined for each metal by titration of the carbon in suspension in aqueous phase, at constant acidity, with the metal itself. For each titration point, the concentration of the metal in the solution phase after equilibration was determined, and the data were processed by the Ruzic linearization method, to obtain the concentration of the active sites involved in the sorption, and the conditional constant. The effect of the pH was also examined, in the range 4-6, obtaining that the adsorption increases at increasing pH. The protonation and adsorption constants were determined from the conditional adsorption coefficients obtained at the different acidities. The concentration of the active sites is 0.023 and 0.042 mmol g⁻¹, and the protonation constants are 1.0×10⁶ and 4.6×10⁴ M⁻¹ for Pb(II) and Cu(II). The corresponding adsorption constants are respectively 1.4×10⁵ and 6.3×10³ M⁻¹. All the parameters are affected by a large uncertainty, probably due to the heterogeneity of the active groups in the activated carbon. Even if so, these parameters make it possible a good prediction of the adsorption in a wide range of conditions. Other sorption mechanism can be set up at different conditions, in particular at different pH, as it has been demonstrated in the case of copper(II).     

Cu(II) Hexacyanoferrate(III) Modified Carbon Paste Electrode; Application for Electrocatalytic Detection of Nitrite

Copper hexacyanoferrate (CuHCF) film‐modified carbon paste electrode (CPE) has been prepared from various electrolytic aqueous solutions using consecutive cyclic voltammetry. The cyclic voltammograms showed the direct deposition of CuHCF films from the mixing of Cu²⁺ and Fe(CN)₆^3? ions and each time with one of the six cations: H⁺, Na⁺, K⁺, NH₄⁺, Mg²⁺, and Al³⁺. The CuHCF film showed a single redox couple that exhibited a cation effect (Na⁺, K⁺, Mg²⁺, and NH₄⁺) and anion effect (Cl^?, NO₃^?, SO₄^2?, ClO₄^?, and BrO₃^?) in the cyclic voltammograms. Voltammetric studies have indicated that in presence of nitrite, the cathodic peak current of CuHCF increases, followed by a decrease in the corresponding anodic current. This indicated that nitrite was reduced by the redox mediator immobilized on the electrode surface via an electrocatalytic mechanism. The process of reduction and its kinetics were investigated by using cyclic voltammetry, differential pulse voltammetry, chronoamperometry and chronocoulometry techniques. The electrocatalytic ability about 800 mV can be seen. The rate constant of the catalytic reduction of nitrite was found to be 7.9×10⁵ cm³ mol^?1 s^?1. Linearity range obtained was 5×10^?5?8.4×10^?3 by cyclic voltammetry and 8×10^?6?1.3×10^?3 and 4×10^?3?2×10^?2 by differential pulse voltammetry.     

Characteristics of subtractive anodic stripping voltammetry of Pb and Cd at silver and gold electrodes

Silver and gold electrodes are useful for the quantitative determination of lead and cadmium with subtractive anodic stripping voltammetry (SASV). The use of SASV is essential for achieving good separation between the two peaks, to eliminate the interference of nitrates when cadmium is present and to allow analysis at very low concentrations without the removal of oxygen. The deposition and dissolution of Pb²⁺ and Cd²⁺ proceed at underpotential (UPD) on both electrodes. The UPD properties of the deposits are the main factor determining the analytical characteristics of the ASV method and are strongly affected by the type and concentration of the electrolyte. The effects of anions (Cl⁻, Br⁻, SO₄²⁻, NO₃⁻) and acids (HNO₃, HClO₄, H₂SO₄, HCl) are shown. The two electrodes complement each other and, in addition, enable the qualitative identification of Pb²⁺ and Cd²⁺, since the peaks appear in opposite order on the two electrodes. Analysis of mixtures of the two analytes is restricted on gold but not on silver. At gold the two peaks overlap: (i) at concentrations of cadmium higher than 250 nM at deposition times greater than 30 s, (ii) in the presence of copper at concentrations higher than 1 μM, and (iii) in the presence of Triton X-100 at concentrations above 10 mg/l. The repeatability at 10 nM analyte is better than 2.5%. The detection limits for Pb²⁺ and Cd²⁺ at 120 s deposition time and 3500 rpm rotation rate are: dl_Pb/Ag=0.04 nM; dl_Cd/Ag=0.7 nM; dl_Pb/Au=0.1 nM; dl_Cd/Au=0.3 nM. The analysis of lead and cadmium in natural waters has been performed.     

一种金属单晶电极制备方法的建立和Cu2+在铂单晶上UPD过程的研究

同种材料而表面结构不同的电极往往有完全不同的电化学性能.使用在原子水平上表面结构明确的单晶电极不仅有助于对电极表面吸脱附过程、电场作用下表面结构重组、双电层微观结构、分子水平上的反应机理等基础理论进行深入研究,且对高选择性、高效电催化剂的研制也有指导意义.单晶电化学研究的基础就是制备定向不同的单晶电极.本文建立了金属单晶电极制备方法,并报道了Cu²⁺在Pt单晶电极上UPD(欠电位沉积)过程的研究结果.     

Highly efficient adsorption of Pb(II) by cubic nanocrystals in aqueous solution: Behavior and mechanism

As one of the most toxic heavy metal ions, lead pollution has become an urgent problem. Here, a cubic crystal nanoparticle (Prussian blue analogue, PBA), referred to as potassium manganese ferrocyanide (KMFC) was synthesized and used as a highly-effective sorbent for removing Pb(II) from aqueous solution. KMFC is a mesoporous material that has excellent ion exchange properties, which was confirmed by a series of characterizations. This paper investigated the adsorptive attributes of KMFC for lead ions in aqueous solution. The influences of temperature, contact time and pH on adsorption were studied in batch experiments. The KMFC possessed a robust adsorption capacity for resident lead ions in aqueous solution, which attained 1075.27 mg g⁻¹ at room temperature (25 °C), based on the Langmuir model, which was far higher than any previously reported values. The adsorption process was well fitted to a pseudo-second-order kinetic model, as well as Langmuir and Temkin isotherm models, and was endothermic and spontaneous on the basis of thermodynamic analysis. The adsorption of Pb(II) on the surface of KMFC started with electrostatic attraction, due to the electronegativity of KMFC. Further, ion exchange was the dominant mechanism in this adsorption process, which was confirmed by FTIR, XPS, and other supplementary experiments. The good chemisorption (K⁺ exchange) properties of KMFC suggested that it likely has excellent prospects in applications for heavy metal ions adsorption. This study not only provided a new perspective for the design and development of heavy metal sorbents but provided a deep insight into the mechanism of adsorption of heavy metal ions by PBA.     

Theoretical study of the adsorption of oxygen on a Cu(100) surface and the coadsorption with alkali atoms

We performed a theoretical study of the adsorption of oxygen on a cluster model of the Cu(100) surface and also the surface coadsorbed with lithium and potassium atoms. The study showed that alkali coadsorption facilitates in a significant way the process of molecular adsorption, whereas the adsorption of atomic oxygen is only slightly modified. The alkali atoms on the copper surface produce an increase in the charge transfer toward the oxygen molecule, favoring the oxygen dissociation. The effect is greater for the potassium coadsorption. In addition, we found that the potassium coadsorption favored the dissociation and recombination processes by about 60 and 15%, respectively. In turn, the lithium coadsorption favored only the recombination process by about 50%. These results could be an important aspect for catalytic processes.From the Proceedings of the 28th Congreso de Quimicos Teóricos de Expression Latina (QUITEL 2002)     

Template carbon dispersed in polyaniline matrix electrodes: evaluation and application as electrochemical sensors to low concentrations of Cu and Pb

A new electrode, obtained by the dispersion of template carbon nanoparticles onto polyaniline, is presented in this paper. Template carbon was synthesized via the pyrolysis of the polyfurfuryl alcohol inside the nanometric pores of porous Vycor glass, and the electrodes were prepared by a polyaniline-template carbon mixture. Scanning electron microscopy showed that polyaniline-template carbon films presented a wholly modified morphology when compared to polyaniline and polyaniline-graphite films. Electrochemical characterization indicated that the interconversion reactions of polyaniline were strongly facilitated in the presence of the template carbon. The new electrode also exhibited excellent chemical and physical stabilities. Finally, anodic stripping voltammetry measurements revealed that the new electrode presented a noteworthy linear response to very low concentrations of Cu²⁺ and Pb²⁺ ions, under few minutes of pre-concentration.     

锑(III)在铂电极上的欠电位沉积行为

由于经欠电位沉积（UPD）形成的吸附金属原子居可以改变电极表面的结构和组成，从而达到增强电祝活性的目的，因此欠电位沉积在电化学领域中颇受重视．对于梯（Ⅲ）的欠电位沉积行为，自1953年Mills和Wills发现锑（Ⅲ）可在AS电极上形成单电子层[1]以后，Schimide等人和Motoo等人分别研究证实梯（Ⅲ）可在Au电极上[2]和Pt电极上[3]发生火电位沉积，并且Motoo等人使用梯（V）化合物测定了每个吸附梯原子占据的铂原子数[4]．本文试图用电位扫描法、微分电容法、电位阶跃法等实验方法对锑（Ⅲ）在柏电极上的大电位沉积并为进行系统的研究…     

Aflatoxin B(1) adsorption by natural and copper modified montmorillonite

Adsorption of aflatoxin B(1) (AFB1) by natural montmorillonite (MONT) and montmorillonite modified with copper ions (Cu-MONT) was investigated. Both MONTs were characterized using the X-ray powder diffraction (XRPD) analysis, thermal analysis (DTA/TGA) and scanning electron miscroscopy/electron dispersive spectroscopy (SEM/EDS). The results of XRPD and SEM/EDS analyses of Cu-MONT suggested partial ion exchange of native inorganic cations in MONT with copper occurred. Investigation of AFB1 adsorption by MONT and Cu-MONT, at pH 3, 7 or 9, showed that adsorption of this toxin by both MONTs was high (over 93%). Since AFB1 is nonionizable, no differences in AFB1 adsorption by both MONTs, at different pHs, were observed, as expected. Futhermore, it was determined that adsorption of AFB1 by both MONTs followed a non-linear (Langmuir) type of isotherm, at pH 3. The calculated maximum adsorbed amounts of AFB1 by MONT (40.982mg/g) and Cu-MONT (66.225mg/g), derived from Langmuir plots of isotherms, indicate that Cu-MONT was much effective in adsorbing AFB1. Since, the main cation in an exchangeable position in MONT is calcium, and in Cu-MONT both calcium and copper, the fact that ion exchange of inorganic cations in MONT with copper increases adsorption of AFB1 suggests that additional interactions between AFB1 and copper ions in Cu-MONT caused greater adsorption.