Ampholytes as background electrolytes in capillary zone electrophoresis: sense or nonsense? Histidine as a model ampholyte

A lot of phenomena, occuring in capillary zone electrophoresis (CZE), are linked with the ionic concentration of the background electrolyte (BGE). If weak bases and acids are used as BGEs in CZE, at a pH where they are scarcely ionized, the ionic concentration of the BGE is very low and this brings a strong peak broadening, limited sample stacking and low sample load. Because the electromigration dispersion increases extremely, moreover, the existence of low-conductivity BGEs in CZE is a contradiction in terms. The behavior of ampholytes as BGE in CZE is examined, by means of histidine as a model ampholyte. For BGEs consisting of histidine, important parameters, including the ionic concentrations, buffer capacity, transfer ratio, and the indicator for electromigration dispersion E(1)m(1)/E(2)m(2), are calculated at various pH. Although the transfer ratio is fairly constant over the whole pH traject, the ionic concentration and buffer capacity decrease whereas the electromigration dispersion strongly increases near the pI of histidine. I.e., that ampholytes can be applied as BGEs in CZE, however, just not at pH near their pI value, except as the difference between the pK values of the basic and acidic group, the deltapK value, is very small. For ampholytes with a low deltapK value or at high concentrations, all the before-mentioned effects are less fatal, but in that case we can not speak of a real low-conductivity BGE. If ampholytes are used at pH near their pK values, the use of ampholytes as BGE is not advantageously compared with simple weak bases and acids. This has been confirmed by calculations and experiments.     

三角形法和四面体法优化选择毛细管区带电泳背景电解质

建立了两种高效、快速的毛细管区带电泳背景电解质(BGE)的优化方法三角形优化法和四面体优化法。以色谱指纹图谱指数F和色谱指纹图谱相对指数Fr作为评价毛细管电泳分析系统的目标函数,以雪莲药材水提取液为样品,考察一定浓度的硼砂、硼酸、磷酸氢二钠和磷酸二氢钠溶液按三角形优化法和四面体优化法构成背景电解质时对样品的分离情况,通过添加有机改性剂和调节pH进行再优化。用三角形法优化出以50 mmol/L硼砂-含3%乙腈的150 mmol/L磷酸二氢钠(体积比为1∶1)作为BGE时分离效果最佳,用四面体法优化出以50 mmol/L硼砂-150 mmol/L磷酸二氢钠-200 mmol/L硼酸(体积比为1∶1∶2,用0.1 mol/L氢氧化钠调pH 8.55)作为BGE时分离效果最佳,分别获得28个和25个电泳峰。所建立的方法操作简捷,适用于中药材水提取液或醇提取液的毛细管区带电泳BGE的选择。     

Influence of pH on electrophoretic behavior of phenothiazines and determination of pKa values by capillary zone electrophoresis

The influence of buffer pH on the electrophoretic behavior of 13 structurally related phenothiazines and determination of pK(a) values by capillary zone electrophoresis (CZE) were investigated. The results indicate that phenothiazines with a piperazine substituent behave quite differently from those with substituents having an aliphatic side chain or a piperidine moiety over the pH range studied. To separate these phenothiazines, it is preferable to select buffer pH in the range of 2.5-3.5. The pK(a) values of phenothiazines with three different types of substituents attached at the 10-position of the phenothiazine ring were determined. The determination of pK(a) values of phenothiazines allows us to rationalize the influence of buffer pH on the migration behavior of these compounds in CZE.     

Determination of acid-base dissociation constants of azahelicenes by capillary zone electrophoresis

CZE was employed to determine acid-base dissociation constants (pK(a)) of ionogenic groups of azahelicenes in methanol (MeOH). Azahelicenes are unique 3-D aromatic systems, which consist of ortho-fused benzene/pyridine units and exhibit helical chirality. The pK(a) values of pyridinium groups of the studied azahelicenes were determined from the dependence of their effective electrophoretic mobility on pH by a nonlinear regression analysis. The effective mobilities of azahelicenes were determined by CZE at pH range between 2.1 and 10.5. Thermodynamic pK(a) values of monobasic 1-aza[6]helicene and 2-aza[6]helicene in MeOH were determined to be 4.94 +/- 0.05 and 5.68 +/- 0.05, respectively, and pK(a) values of dibasic 1,14-diaza[5]helicene were found to be equal to 7.56 +/- 0.38 and 8.85 +/- 0.26. From these values, the aqueous pK(a) of these compounds was estimated.     

Capillary zone electrophoresis of soil humic acid fractions obtained by coupling size-exclusion chromatography and polyacrylamide gel electrophoresis

Capillary zone electrophoresis (CZE) was used for characterisation of soil humic acid (HA) fractions obtained by coupling size-exclusion chromatography with polyacrylamide gel electrophoresis, on the basis of their molecular size and electrophoretic mobility. CZE was conducted using several low alkaline buffers as background electrolyte (BGE): 50 mM carbonate, pH 9.0; 50 mM phosphate, pH 8.5; 50 mM borate, pH 8.3; 50 mM Tris-borate+1 mM EDTA+7 M urea+0.1% sodium dodecyl sulphate (SDS), pH 8.3. Independently of BGE conditions, the effective electrophoretic mobility of HA fractions were in good agreement with their molecular size. The better resolution of HA were obtained in Tris-borate-EDTA buffer with urea and SDS. This results indicated that CZE, mostly with BGE-contained disaggregating agents, is useful for separating HAs in fractions with different molecular sizes.     

Determination of acid-base dissociation constants of very weak zwitterionic heterocyclic bases by capillary zone electrophoresis

Thermodynamic acid-base dissociation (ionization) constants (pK(a)) of seven zwitterionic heterocyclic bases, first representatives of new heterocyclic family (2,3,5,7,8,9-hexahydro-1H-diimidazo[1,2-c:2',1'-f][1,3,2]diazaphosphinin-4-ium-5-olate 5-oxides), originally designed as chiral Lewis base catalysts for enantioselective reactions, were determined by capillary zone electrophoresis (CZE). The pK(a) values of the above very weak zwitterionic bases were determined from the dependence of their effective electrophoretic mobility on pH in strongly acidic background electrolytes (pH 0.85-2.80). Prior to pK(a) calculation by non-linear regression analysis, the CZE measured effective mobilities were corrected to reference temperature, 25°C, and constant ionic strength, 25 mM. Thermodynamic pK(a) values of the analyzed zwitterionic heterocyclic bases were found to be particularly low, in the range 0.04-0.32. Moreover, from the pH dependence of effective mobility of the bases, some other relevant characteristics, such as actual and absolute ionic mobilities and hydrodynamic radii of the acidic cationic forms of the bases were determined.     

Simultaneous determination of deoxycytidine diphosphate and deoxycytidine triphosphate by capillary electrophoresis with transient isotachophoretic stacking: a sensitive monitoring method for ribonucleotide reductase activity

A simple and rapid capillary electrophoretic method was developed for simultaneous determination of sub‐micromolar 2′‐deoxycytidine 5′‐diphosphate (dCDP) and 2′‐deoxycytidine 5′‐triphosphate (dCTP) levels in enzyme assays without using radioactively labeled substrates. The separation was performed at 25°C using MES in the BGE as the terminating ion, the chloride ions in the sample buffer as the leading ion, and PEG 4000 in the BGE as the EOF suppressor for sample stacking by transient isotachophoresis (tITP). Several parameters affecting the separation were investigated, including the pH of the BGE, the concentration of sodium chloride in the sample buffer, and the concentrations of MES and PEG 4000 in the running buffer. Good separation with high separation efficiency was achieved within 6 min under optimal conditions. In comparison with the simple CZE method, the present tITP‐CZE method enabled a 150‐fold increase in the injection time without any decrease in resolution and the sensitivity was enhanced up to two orders of magnitude with the new method. The linear range of the method was 0.1–10 μM for dCDP and dCTP. The limits of detection of dCDP and dCTP were 85 and 73 nM, respectively. The proposed method was successfully applied for the activity assay of ribonucleotide reductase from Hep G2 and Sf9 cells.     

Fast high-throughput method for the determination of acidity constants by capillary electrophoresis. II. Acidic internal standards

A fast method for the determination of acidity constants by CZE has been recently developed. This method is based on the use of an internal standard of pK(a) similar to that of the analyte. In this paper we establish the reference pK(a) values of a set of 24 monoprotic neutral acids of varied structure that we propose as internal standards. These compounds cover the most usual working pH range in CZE and facilitate the selection of adequate internal standards for a given determination. The reference pK(a) values of the acids have been established by the own internal standard method, i.e. from the mobility differences between different acids of similar pK(a) in the same pH buffers. The determined pK(a) values have been contrasted to the literature pK(a) values and confirmed by determination of the pK(a) values of some acids of the set by the classical CE method. Some systematic deviations of mobilities have been observed in NaOH buffer in reference to the other used buffers, overcoming the use of NaOH in the classical CE method. However, the deviations affect in a similar degree to the test compounds and internal standards allowing thus, the use of NaOH buffer in the internal standard method. This fact demonstrates the better performance of the internal standard method over the classical method to correct mobility deviations, which together with its fastness makes it an interesting method for the routine determination of accurate pK(a) values of new pharmaceutical drugs and drug precursors.     

Determination of nitrate in seawater by capillary zone electrophoresis with chloride-induced sample self-stacking

A capillary zone electrophoresis (CZE) method was established to determine low concentration nitrate which was online preconcentrated with chloride-induced leading-type sample self-stacking for seawater samples. The sample self-stacking was based on transient isotachophoresis in which chloride served as leading ion, and dihydrogenphosphate in the background electrolyte (0.1 M phosphate) as the terminating one. Due to the small mobility difference between nitrate and chloride, the isotachophoresis time was so long that nitrate could not separate from the rear sharp boundary between chloride and the background electrolyte (BGE) when it migrated to the detection window. A zwitterionic surfactant, 3-(N,N-dimethyldodecylammonio)propane sulfonate was added to the BGE to enlarge the mobility difference for its selective interaction with anions. Thus, a highly conductive sample could be injected in a large volume with about fourfold sensitivity enhancement compared to that of field amplification sample stacking in which nitrate was dissolved in pure water. The relative standard deviations (n=5) of migration time, peak area, peak height were 0.1, 3.0, 1.5%, respectively. The limit of detection (S/N=3) for nitrate was 35 microg/l in seawater samples with relatively low concentration BGE (0.1 M sodium phosphate, pH 6.2). The overall procedure consisting of online preconcentration and separation was as simple as routine CZE except for a slightly longer sample injection time (3-4 min).     

Influence of the nature of the electrolyte on the chiral separation of basic compounds in nonaqueous capillary electrophoresis using heptakis(2,3-di-O-methyl-6-O-sulfo)-beta-cyclodextrin

The influence on the enantiomeric resolution of the nature of the cationic BGE component (sodium, ammonium or potassium) and that of the anionic component (chloride, formate, methanesulfonate or camphorsulfonate) as well as the concentration of heptakis(2,3-di-O-methyl-6-O-sulfo)-beta-cyclodextrin (HDMS-beta-CD), the selected chiral selector, was studied in nonaqueous capillary electrophoresis (NACE). For this purpose, two D-optimal designs with 33 and 26 experimental points were applied. Three beta-blockers (atenolol, celiprolol and propranolol) and three local anesthetics (bupivacaine, mepivacaine and prilocaine) were selected as basic model compounds. Both cationic and anionic BGE components were found to have a deep impact on the enantiomeric resolution of the investigated analytes but it is the cationic component that has shown the strongest influence. Indeed, in some cases, the change of the latter led to a complete loss of enantioresolution. Based on the observed results, two NACE systems were recommended, namely ammonium formate and potassium camphorsulfonate in a methanolic solution containing HDMS-beta-CD and acidified with formic acid, in order to separate efficiently the enantiomers of basic drugs.     

In‐line preconcentration capillary zone electrophoresis for the analysis of haloacetic acids in water

Two in‐line enrichment procedures (large volume sample stacking (LVSS) and field amplified sample injection (FASI)) have been evaluated for the CZE analysis of haloacetic acids (HAAs) in drinking water. For LVSS, separation on normal polarity using 20 mM acetic acid–ammonium acetate (pH 5.5) containing 20% ACN as BGE was required. For FASI, the optimum conditions were 25 s hydrodynamic injection (3.5 kPa) of a water plug followed by 25 s electrokinetic injection (?10 kV) of the sample, and 200 mM formic acid–ammonium formate buffer at pH 3.0 as BGE. For both FASI and LVSS methods, linear calibration curves (r²>0.992), limit of detection on standards prepared in Milli‐Q water (49.1–200 μg/L for LVSS and 4.2–48 μg/L for FASI), and both run‐to‐run and day‐to‐day precisions (RSD values up to 15.8% for concentration) were established. Due to the higher sensitive enhancement (up to 310‐fold) achieved with FASI‐CZE, this method was selected for the analysis of HAAs in drinking water. However, for an optimal FASI application sample salinity was removed by SPE using Oasis WAX cartridges. With SPE‐FASI‐CZE, method detection limits in the range 0.05–0.8 μg/L were obtained, with recoveries, in general, higher than 90% (around 65% for monochloroacetic and monobromoacetic acids). The applicability of the SPE‐FASI‐CZE method was evaluated by analyzing drinking tap water from Barcelona where seven HAAs were found at concentration levels between 3 and 13 μg/L.     

Enantiomeric separation of some demethylated analogues of clofibric acid by capillary zone electrophoresis and nano-liquid chromatography

The enantiomeric separation of some demethylated analogues of clofibric acid, namely 2-(6-chloro-benzothiazol-2-ylsulfanyl)-, 2-(6-methoxy-benzothiazol-2-ylsulfanyl)-, 2-(quinolin-2-yloxy)-, 2-(6-chloro-quinolin-2-yloxy)-, 2-(7-chloro-quinolin-4-yloxy)-propionic acid (compounds A-E, respectively), has been studied by CZE and nano-LC using for the first technique two beta-CD derivatives and vancomycin added to the BGE and vancomycin-modified silica particles for the second one, with the aim to find the optimum experimental conditions for the baseline resolution. The type and the concentration of the chiral selector added to the BGE, the buffer pH, the type of organic modifier and its concentration, the capillary temperature and the applied voltage played a very important role in the enantioresolution of the analysed compounds. The use of 6-monodeoxy-6-monoamino-beta-CD allowed to achieve baseline resolution of four of five clofibric acid derivatives in less than 10 min while heptakis-(2,3,6-tri-O-methyl)-beta-CD partially resolved the same compounds in their enantiomers. Employing vancomycin as the chiral selector in CZE, the counter-current partial filling method was chosen achieving baseline resolution of four analytes. All the studied compounds were enantioresolved employing a capillary column packed with vancomycin stationary phase by nano-LC, and the resolution was strongly influenced by the concentration of the organic modifier and by the pH of the mobile phase. The best results were achieved at pH 4.5 in presence of 60% of methanol (MeOH). However, longer analysis times were observed in the experiments carried out by nano-LC.     

Investigation of the effect of ionic strength of Tris-acetate background electrolyte on electrophoretic mobilities of mono-, di-, and trivalent organic anions by capillary electrophoresis

The effect of ionic strength of the background electrolyte (BGE) composed of tris(hydroxymethyl)aminomethane (Tris) and acetic acid on the electrophoretic mobility of mono-, di- and trivalent anions of aliphatic and aromatic carboxylic and sulfonic acids was investigated by capillary zone electrophoresis (CZE). Actual ionic mobilities of the above anions were determined from their CZE separations in Tris-acetate BGEs of pH 8.1 to 8.2 in the 3 to 100 mM ionic strength interval at constant temperature (25 degrees C). It was found that the ionic strength dependence of experimentally determined actual ionic mobilities does not follow the course supposed by the classical Onsager theory. A steeper decrease of actual ionic mobilities with the increasing ionic strength of BGE and a higher estimated limiting mobility of the anions than that found in the literature could be attributed to the specific behavior of the Tris-acetate BGEs. Presumably, not only a single type of interaction of anionic analytes with BGE constituents but rather the combination of effects, such as ion association or complexation equilibria, seems to be responsible for the observed deviation of the concentration dependence of the actual ionic mobilities from the Onsager theory. Additionally, several methods for the determination of limiting ionic mobilities from CZE measured actual ionic mobilities were evaluated. It turned out that the determined limiting ionic mobilities significantly depend on the calculation procedure used.     

Electrolysis phenomena in electrophoresis

We present a new theoretical approach for calculating changes in the physico-chemical properties of BGEs for measurements by CZE due to the electrolysis in electrode vials (vessels). Electrolysis is an inevitable phenomenon in any measurement in CZE. Water electrolysis, which occurs in most measurements, can significantly alter the composition of the BGE in electrode vials and in the separation capillary and has a negative influence on the robustness and quality of separations. The ability to predict changes in the composition of the BGE is important for evaluation of the suitability of the BGEs for repeating electrophoretic runs. We compared theoretically calculated changes in the physico-chemical properties (pH, conductivity) with those measured using pH-microelectrode and contactless conductivity detection of the BGE after the electrophoretic run. We confirmed the validity of our theoretical approach with a common BGE composed of acid-base pair, where one constituent is fully dissociated while the second constituent is dissociated by only half, and with Good's buffer. As predicted by theoretical approach, the changes in the physico-chemical properties of the Good's buffer after the electrophoretic run were several times lower than in the case of a common BGE composed of a weak acid – strong base pair.     

Effect of barium tetraborate on the separation of tryptic digests of proteins by zone electrophoresis in uncoated capillaries

A simple, fast, efficient and reproducible method for peptide separations in CZE is reported. It consists in running tryptic digests of peptides in an uncoated capillary, in a BGE composed of tetraborate as a buffering ion, in which the typical sodium counterion is substituted with barium. Efficient absorption of this divalent cation to ionized silanols and barium silicate precipitation seem to be able to shield effectively the silica surface from separands. This is demonstrated by the fact that, when tBa(2+) ions are present in solution (from pH 8.5 up to pH 11.0), the electroendoosmotic flow is reversed; such reversal being progressively higher at higher pH values, by up to a four-fold. Separations become progressively better at higher pH values, whereas at pH 11 in sodium tetraborate they are dramatically worsened. It is further hypothesized that the barium silicate layer further protects the silica surface against dissolution and corrosion which is quite substantial at pH 11.     

Potential of CE for the determination of inorganic and acidic anions in cyanoacrylate adhesives

In this work, a CZE method with indirect UV detection was developed for the simultaneous determination of the inorganic and acidic anions, chloride, sulfate, nitrate, fluoride, formate, phosphate, diethylphosphate, methyl sulfonate, cyanoacetate, and methacrylate present in cyanoacrylate adhesives. Chromate was employed as the probe ion, and the EOF was reversed by incorporating CTAB into BGE. Detection limits of 0.7-4.6 microg/mL were obtained for all the anions studied. The CE method developed is a significant improvement on traditionally used chromatographic methods such as ion chromatography, as it resulted in shorter analysis times with enhanced separation efficiencies. This method was successfully employed for the analysis of inorganic and acidic anions in cyanoacrylate adhesive samples.     

逍遥丸的毛细管电泳指纹图谱的建立

采用毛细管区带电泳法建立了逍遥丸(Xiaoyao Pill, XYP)的毛细管电泳指纹图谱(CEFP)。运用正方形优化法,以色谱指纹图谱分离量指数(RF)为优化的目标函数,对建立指纹图谱的实验条件进行了优化,确定了最佳背景电解质(BGE)溶液50 mmol/L硼砂-50 mmol/L磷酸氢二钠-150 mmol/L磷酸二氢钠-50 mmol/L碳酸氢钠(1:1:1:5, v/v/v/v; pH 7.40)、紫外检测波长228 nm、运行电压12 kV、重力进样25 s (高度14 cm)的分离检测条件。采用未涂层石英毛细管(70 cm×75 μm,有效分离长度57 cm)分离,以咖啡酸色谱峰为参照,确定13批逍遥丸样品的21个共有指纹峰。通过聚类分析确定用其中10批样品生成对照CEFP,以此为标准用系统指纹定量法鉴别13批逍遥丸的质量,结果显示: S3号样品的化学成分数量和分布比例不合格,S10和S12号样品含量明显偏高,其余批次质量均合格。所建立的正方形优化法操作简便,适用于中药的毛细管区带电泳BGE的选择;所建立的逍遥丸CEFP具有较好的精密度和重现性,可以为逍遥丸的质量控制提供新的参考。     

On-line coupling of capillary isotachophoresis and capillary zone electrophoresis for the determination of flavonoids in methanolic extracts of Hypericum perforatum leaves or flowers

Five flavonoids (hyperoside, isoquercitrin, quercitrin, quercetin and rutin) were separated and determined in extracts of Hypericum perforatum leaves or flowers by capillary zone electrophoresis (CZE) with isotachophoretic (ITP) sample pre-treatment using on-line column coupling configuration. The background electrolyte (BGE) used in the CZE step was different from the leading and terminating ITP electrolytes but all the electrolytes contained 20% (v/v) of methanol. The optimal leading electrolyte was 10 mM HCl of pH* approximately 7.2 (adjusted with Tris) and the terminating electrolyte was 50 mM H3BO3 of pH* approximately 8.2 (adjusted with barium hydroxide). This operational system allowed to concentrate and pre-separate selectively the flavonoid fraction from other plant constituents before the introduction of the flavonoids into the CZE capillary. The BGE for the CZE step was 50 mM Tris buffer of pH* approximately 8.75 containing 25 mM N-[tris(hydroxymethyl)methyl]-3-aminopropanesulfonic acid as co-ion and 55 mM H3BO3 as complex-forming agent. The ITP-CZE method with spectrophotometric detection at 254 nm was suitable for the quantitation of the flavonoids in real natural samples; kaempferol was used as internal standard. The limit of detection for quercetin-3-O-glycosides was 100 ng ml(-1) and calibration curves were rectilinear in the range 1-10 microg ml (-1) for most of the analytes. The RSD values ranged between 0.9 and 2.7% (n=3) when determining approximately 0.07-1.2% of the individual flavonoids in dried medicinal plants.     

Speciation of inorganic and methylated arsenic compounds by capillary zone electrophoresis with indirect UV detection. Application to the analysis of alkali extracts of As2S2 (realgar) and As2S3 (orpiment)

A capillary zone electrophoresis (CZE) method with indirect UV detection was developed to simultaneously separate inorganic and organic arsenic compounds including arsenite (iAsIII), arsenate (iAsV), monomethylarsonate and dimethylarsenic acid (DMAV). 2,6-Pyridinedicarboxylic acid (PDC) and n-hexadecyltrimethylammonium hydroxide (CTAOH) were selected to compose a background electrolyte (BGE), where PDC was used as chromophore and CTAOH functioned as electroosmotic flow (EOF) modifier to reduce/eliminate EOF. The choice of detection wavelength, the optimization of BGE pH, and effects of applied electric field strength and temperature on separation were further investigated. The limits of detection for the targeted analytes were between 0.19 and 0.23 ppm as molecule. Good linearity of more than three orders of magnitude was obtained. Repeatability of migration times and peaks areas were 0.8-1.7 and 3.4-6.9% R.S.D.; whereas reproducibility were 1.2-2.2 and 3.6-7.1% R.S.D., respectively. The established CZE method was then applied to analyze the alkali extracts of realgar (As2S2) and orpiment (As2S3). The main components in both alkali extracts were identified to be iAsIII and iAsV.     

Determination of ethyl glucuronide in human serum by hyphenation of capillary isotachophoresis and zone electrophoresis

The determination of ethyl glucuronide (EtG), a marker of recent alcohol consumption, in human serum by hyphenation of capillary ITP (CITP) and CZE is reported. For CITP step, 1 x 10(-2) M hydrochloric acid adjusted with epsilon-aminocaproic acid (EACA) to pH 4.4 was used as the leading electrolyte, and 1 x 10(-2) M nicotinic acid with EACA, pH 4.4, was used as the terminating electrolyte (TE). All electrolytes contained 0.2% hydroxypropylcellulose to suppress electroosmosis. In CITP, EtG was separated from fast serum macrocomponents chloride, phosphate, lactate, and acetate. Zones of microcomponents including EtG that migrated between acetate and nicotinate were forwarded to the second capillary filled with a BGE identical with the TE. Conductivity detection was used in the CITP step. Sensitive detection in the CZE step was performed using indirect spectrophotometric detection at 254 nm. The assay is based on a 1:5 dilution of serum with deionized water and has a concentration LOD for EtG in diluted sample of 9.8 x 10(-9) M. The method was used for the determination of EtG in sera of volunteers consuming alcohol.