等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

碱金属离子对Fe(phen)3/Y催化氧化性能的影响

采用自由配体法,将铁邻菲啰啉(Fe(phen)3)配合物封装在含有不同碱金属阳离子的Y型分子筛中,制备了系列Fe(phen)3/M-Y(M=Li+,Na+,K+和Cs+)催化剂.采用X射线衍射、红外光谱、紫外-可见光谱、热重-差热分析、电感耦合等离子原子发射光谱、N2吸附-脱附以及催化氧化反应考察了碱金属离子对Fe(phen)3/M-Y催化剂物化性质和催化氧化性能的影响.结果表明,交换有不同碱金属离子的Y型沸石中Fe(phen)3的封装量不同,而且Fe(phen)3在Y型沸石中的热稳定性随着碱金属离子半径的增加有所降低,其中Fe(phen)3/Li+-Y具有最高的配合物封装量和热稳定性能.在环己烷或苯乙烯氧化反应中,在较低的反应温度下,Fe(phen)3/K+-Y表现出最高的催化活性,而在较高的反应温度下,Fe(phen)3/Cs+-Y的催化活性最高,碱金属离子对Fe(phen)3/M-Y催化氧化性能的影响是电子效应、空间限制作用和扩散效应的综合结果.     

冠醚络合高活性双金属氰化物制备及CO2与环氧丙烷共聚

首次在共沉淀过程中添加18-冠-6醚络合生成的钾离子得到了均一的高活性冠醚络合的锌-钴双金属催化剂,并用红外光谱(FTIR)、扫描电镜(SEM)、热重红外(TGA-IR)和X射线衍射(XRD)进行了表征.元素分析发现K含量为1.2%. FTIR表明未加冠醚络合的双金属催化剂离心后上下部分呈现不同的络合状态,而冠醚络合的双金属催化剂仍保持均一. SEM表明冠醚络合的双金属催化剂为均一松散的结构.由于生成的钾离子被冠醚络合,不影响聚合反应效果. TGA-IR表明冠醚不仅络合K离子,还参与对金属活性中心的络合. XRD表明此催化剂具有低的结晶度.所制冠醚络合的锌-钴双金属催化剂能成功催化CO2与环氧丙烷共聚,其中CDMC3催化得到的共聚物碳酸酯含量为47.8%,副产物环状碳酸酯为1.5%,催化效率高达5122 g/g催化剂(32600 g/g Zn),明显优于不添加冠醚以同样工艺制备的DMC1(共聚物碳酸酯含量29.2%,副产物环状碳酸酯3.3%,催化效率4100 g/g催化剂(16300 g/g Zn).与不添加冠醚8次洗涤离心得到的DMC2相当(共聚物碳酸酯含量48.3%,副产物环状碳酸酯含量2.4%,催化效率5073 g/g催化剂(16400 g/g Zn)).基于此结果提出了两步的反应机理假设.     

球磨双金属氰催化剂催化CO_2/环氧丙烷/四氯苯酐三元共聚

由于共聚配合剂的加入有利于提高双金属氰催化剂(DMC)的催化活性,因此本文通过加入不同的共聚配合剂,采用绿色高效的机械球磨法制备了Zn-Co DMC催化剂体系,然后将DMC用于制备CO2、环氧丙烷和四氯苯酐(THPA)的三元共聚物聚碳酸亚丙酯四氯苯酐(PPCPA)。通过傅里叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)、多晶X射线衍射(XRD)、凝胶渗透色谱(GPC)和热重分析(TG)等技术手段表征了催化剂和PPCPA的结构和性能。结果表明,共聚配合剂辅助球磨Zn-Co DMC催化聚合反应转化数25.67~141.80,PPCPA数均相对分子量2.21×10~3~3.15×10~3,多分散指数1.04~1.24,呈现窄分布。PPCPA的热稳定性要高于聚碳酸亚丙酯(PPC),热分解温度提高了129.8℃。     

Double perovskite oxides Sr_2Mg_(1-x)Fe_xMoO(6-δ) for catalytic oxidation of methane

The double perovskite oxides Sr2Mg1-xF exMoO6-δ were investigated as catalysts for the methane oxidation.The structural properties of catalysts were characterized in detail by X-ray diffraction,X-ray photoelectron spectroscopy and X-ray absorption spectroscopy.The catalytic property was strongly influenced by the Fe substitution.The relation between catalytic performance and the degree of Fe substitution was examined with regard to the structure and surface characteristics of the mixed oxides.The Fe-containing catalysts exhibited higher activity attributable to the possible(Fe2+,Mo6+) and (Fe3+,Mo5+)valency pairs,and the highest activity was observed for Sr2Mg0.2Fe0.8MoO6-δ.The enhancement of the catalytic activity may be correlated with the Fe-relating surface lattice oxygen species and was discussed in view of the presence of oxygen vacancies.     

Fe/Zn double metal cyanide catalyzed ring-opening polymerization of propylene oxide: 2. Characterization of active structure of double metal cyanide catalysts

Double metal cyanide (DMC) complexes based on Zn₃[Fe(CN)₆]₂ were synthesized using different molar ratios of ZnCl₂ to K₃[Fe(CN)₆] and special complexing agents. IR spectroscopy, electron spectroscopy for chemical analysis, X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and other analytical techniques were employed to characterize these catalysts. The morphology and structure of these DMC catalysts were attributed to the different complexing agents as well as to the different molar ratios of ZnCl₂ to K₃[Fe(CN)₆]. In addition, the catalytic activity was strongly correlated with the morphology and noncrystalline content of DMC catalysts. High-activity catalysts could be prepared by controlling the structure of DMC catalysts by incorporating complexing agents. The active species of DMC catalysts for ring-opening polymerization are Zn²⁺, [Fe(CN)₆]^3–, Cl^–, and the compound of their ligands.     

Chiral bispyridylamide metal complexes as catalysts for the enantioselective addition of TMSCN to aldehydes

The use of (1R,2R)-N,N′-bis(2-pyridinecarboxyamido)-1,2-diphenylethane metal complexes as catalysts for the enantioselective addition of trimethylsilyl cyanide to aldehydes is described. Enantioselectivities up to 70% ee were obtained with a Ti(IV) catalyst. Complexes with Zr(IV), Sc(III), Yb(III) and Cu(II) afforded less selective catalysts. For the Zr(IV) complex, a rate and selectivity enhancement was observed when adding 0.5 equiv. of water with respect to the catalyst. Studies of the metal complexes involved in the reaction were carried out by means of ¹H NMR spectroscopy. A Zr complex was shown by X-ray crystallography to exhibit distorted octahedral coordination, with the four nitrogen atoms of the doubly deprotonated ligand essentially in one plane.     

硫代硫酸铵预硫化的Mo/Al2O3催化剂加氢脱硫反应性能研究

研究了新型固体硫化剂硫代硫酸铵对加氢脱硫催化剂的预硫化。采用浸渍法将硫代硫酸铵负载在Mo/Al₂O₃模型催化剂上制备出预硫化的催化剂。通过X射线衍射、还原气氛的热重质谱联用和光电子能谱等表征手段研究了预硫化催化剂的物相、活化以及反应后催化剂的表面成分。结果表明,硫代硫酸铵中不同价态的硫在催化剂活化过程中起到不同作用,S^2-硫化活性金属,S⁶⁺修饰载体,减少载体与活性金属的相互作用,促进硫化。不同S/Mo摩尔比的预硫化催化剂经原位氢气活化用于噻吩加氢脱硫反应,S/Mo摩尔比为3的预硫化催化剂显示出最好的加氢脱硫活性,预硫化催化剂比Mo/Al₂O₃催化剂的脱硫活性提高17%。     

In situ spectroscopy and spectroelectrochemistry of uranium in high-temperature alkali chloride molten salts

Soluble uranium chloride species, in the oxidation states of III+, IV+, V+, and VI+, have been chemically generated in high-temperature alkali chloride melts. These reactions were monitored by in situ electronic absorption spectroscopy. In situ X-ray absorption spectroscopy of uranium(VI) in a molten LiCl-KCl eutectic was used to determine the immediate coordination environment about the uranium. The dominant species in the melt was [UO 2Cl 4] (2-). Further analysis of the extended X-ray absorption fine structure data and Raman spectroscopy of the melts quenched back to room temperature indicated the possibility of ordering beyond the first coordination sphere of [UO 2Cl 4] (2-). The electrolytic generation of uranium(III) in a molten LiCl-KCl eutectic was also investigated. Anodic dissolution of uranium metal was found to be more efficient at producing uranium(III) in high-temperature melts than the cathodic reduction of uranium(IV). These high-temperature electrolytic processes were studied by in situ electronic absorption spectroelectrochemistry, and we have also developed in situ X-ray absorption spectroelectrochemistry techniques to probe both the uranium oxidation state and the uranium coordination environment in these melts.     

稀土Eu掺杂PtRu/C催化剂及其对甲醇电氧化的性能

采用化学还原和热处理方法对商业PtRu/C催化剂进行稀土Eu掺杂,制备了不同Eu含量的PtRuEux/C催化剂.透射电子显微镜(TEM)、X射线能量色散光谱(EDX)、X射线衍射(XRD)和X射线光电子能谱(XPS)等方法表征催化剂的结果表明,Eu的掺杂未改变PtRu/C催化剂的平均粒径(约为3nm),并且Eu以金属和氧化物两种形态修饰PtRu表面.循环伏安和计时电流法测试显示,PtRuEux/C催化剂较商业PtRu/C对甲醇氧化具有更高的活性,其中PtRuEu0.3/C的活性最高.运用原位傅里叶变换红外(FTIR)光谱从分子水平研究了该催化剂对甲醇电催化氧化的反应过程,检测到甲醇在催化剂上解离吸附的吸附态产物是线型吸附态CO(COL),Eu的掺杂使COL的氧化电位降低,明显提高了催化剂的活性和抗CO毒化的能力.     

Removal of residual metal catalysts with iron/iron oxide nanoparticles from coordinating environments

The application of Fe@FexOy nanoparticles was examined for the sequestration of catalytic metal impurities from organic reaction products. An X-ray photoelectron spectroscopy (XPS) study of the recovered particles confirmed Fe@FexOy sequestered Co2+, Cu2+, Ni2+, RhX+, Pd2+, Ag+, and Pt4+ by coordination of the metal ion to the iron oxide surfaces and followed by subsequent reduction of the surface-bonded ions to their metallic state. Fe@FexOy metal sequestration was found to be effective for catalyst impurities in the absence of strongly coordinating environments but was inhibited by the presence of phosphines. Sequestration of phosphine-coordinated metal impurities was achieved through the addition of either cysteamine or 3-mercaptopropionic acid to the Fe@FexOy during sequestration. This approach was applied to model syntheses using Grubbs' Catalyst (first generation), Pd(PPh3)4, Pd2(dba)3, and Wilkinson's Catalyst (RhCl(PPh3)3).