恒电位法低浓度苯胺的电化学聚合研究

对恒电位法低浓度苯胺的电化学聚合进行了研究，推导了受扩散和电极反应同时控制的聚合电流方程式，成功地进行了验证，并对与聚合反应有关的电化学参量αＡ、ｋＢ，ＤＲ进行了测定。     

超微电极上恒电位法苯胺的电化学聚合研究

本文对超微盘电极上苯胺的恒电位电化学聚合进行了研究，对聚合电流随时间的关系进行了详细的讨论，提出了径向聚合计时电流方程式并进行了验证，实验结果与理论相符。     

铈对低镍铬锰氮奥氏体不锈钢晶间腐蚀的影响研究

针对不同稀土Ce含量的低镍铬锰氮奥氏体不锈钢,采用电化学动电位再活化法和Cu-CuSO4-16%H2SO4热酸浸泡法研究了两种热处理状态下不同铈含量试样的晶间腐蚀程度。研究结果表明:两种热处理状态下,未添加稀土试样腐蚀最严重。不同稀土含量的试样750℃敏化处理2 h比650℃敏化处理2 h腐蚀程度略重。从两组试验的金相显微组织照片和EPR活化率数据来看,两种热处理状态稀土Ce含量为0.053%时奥氏体不锈钢抗晶间腐蚀能力最强,但当铈含量增加到0.067%时,试样腐蚀又开始恶化。     

多组分丝素蛋白-Cu(II)配合物的EPR谱解析

基于二阶微扰理论建立了对具有超精细耦合结构的多组分复杂EPR(顺磁共振)谱的解析拟合方法,并以丝素蛋白-Cu(II)配合物的EPR谱为例进行解析分析,从而有效地解释了Cu(II)离子在蚕吐丝过程中的作用.该方法和应用程序能为类似问题的解决(如Fe(II)、Mn(II)、V(III)及其它顺磁性离子配合物EPR谱的解析)提供方便.     

多组分丝素蛋白-Cu(II)配合物的EPR谱解析

基于二阶微扰理论建立了对具有超精细耦合结构的多组分复杂EPR(顺磁共振)谱的解析拟合方法, 并以丝素蛋白-Cu(II)配合物的EPR谱为例进行解析分析, 从而有效地解释了Cu(II)离子在蚕吐丝过程中的作用. 该方法和应用程序能为类似问题的解决(如Fe(II)、Mn(II)、V(III)及其它顺磁性离子配合物EPR谱的解析)提供方便.     

基于电化学噪声研究模拟海洋大气环境下304不锈钢的点蚀行为

基于电化学噪声技术建立了不锈钢海洋大气点蚀监测系统,利用该系统对处于干湿循环环境下不锈钢的点蚀行为进行监测. 使用时域谱图、时域统计、频域谱图和散粒噪声理论等分析方法对采集到的电化学噪声数据进行处理分析,并结合动电位极化法,形貌分析法共同研究不锈钢的点蚀行为. 研究结果表明,304不锈钢在模拟海洋大气环境下的点蚀行为分为钝化、亚稳态点蚀和稳态点蚀三个阶段. 在钝化阶段,电位电流噪声信号出现少量的同步异向波动,腐蚀事件发生频率高,平均电量低;在亚稳态点蚀阶段,电位电流噪声信号出现大量的同步同向波动,腐蚀事件发生频率降低,平均电量上升,通过扫描电镜观察蚀点;在稳态点蚀阶段,电位电流噪声信号不仅存在大量的同步同向波动,还出现了同步异向波动,腐蚀事件发生频率较低,平均电量大幅度上升,通过扫描电镜观察到电极表面出现小而浅的蚀点. 而动电位极化法可以证实304不锈钢点蚀的发生. 两种分析方法所得结果具有较好的一致性,证明该监测系统很好地实现了对模拟海洋大气环境下304不锈钢点蚀行为的连续监测,并能判断点蚀的发生.     

钠盐溶液中U(Ⅵ)的电化学电子转移与晶化研究

采用循环伏安法分析钠盐溶液中U(Ⅵ)的电化学行为,恒电位电化学还原处理U(Ⅵ),利用交流阻抗谱分析电化学还原反应中的过程动力学特性,利用X射线衍射、扫描电子显微镜和电子能谱等方法分析了U(Ⅵ)的电化学晶化.结果表明,在钠盐溶液中,U(Ⅵ)可通过电化学反应先还原成低价的U(V)并进一步还原为U(Ⅳ),U(Ⅳ)一步氧化为U(Ⅵ),U(Ⅳ)/U(Ⅵ)之间的电化学转化过程受扩散控制,且U(Ⅵ)的电化学电子转移易受环境p H值的影响;恒电位还原4 h时,溶液中U(Ⅵ)的去除率可达90%,U(Ⅵ)的结晶固化产物主要以固态的(UO2)6O2(OH)8·6H2O(水铀矿)和UO2的形式附着在工作电极上.     

阿托伐他汀钙的电化学行为及其应用研究

采用线性扫描伏安法、循环伏安法及恒电位电解法研究了新型抗血脂紊乱药物阿托伐他汀钙(AC)的电化学行为,建立了一种直接测定AC的伏安方法。在0.06 mol/L KH2PO4-Na2HPO4(pH 7.17)缓冲溶液中,AC产生一个还原波,实验结果表明:该还原波属于AC的催化氢波,其峰电流与AC浓度在5.0×10-6~4.0×10-5mol/L范围内呈良好的线性关系,检出限为2×10-6mol/L。     

流动注射-电化学发光法测定煤灰中痕量钼(Ⅵ)

基于钼(Ⅵ)在-0.60V(vs.Ag/AgCl)电位下在线还原为钼(Ⅲ),且在碱性条件下钼(Ⅲ)与鲁米诺发生化学发光反应,据此提出了流动注射-电化学发光法测定煤灰中痕量钼(Ⅵ)的方法。钼(Ⅵ)的质量浓度与化学发光强度的增加值在5.0×10-7～5.0×10-4g.L-1范围内呈线性关系,检出限(3s/k)为5×10-8g.L-1。对1.0×10-6g.L-1钼(Ⅵ)标准溶液进行11次测定,测定值的相对标准偏差为2.6%。方法可用于煤灰中痕量钼(Ⅵ)的测定,测定值与国标方法测定值相符。     

含磷C_(60)衍生物的电化学性能研究

利用循环伏安法测试了 3种新合成的C60 膦酸酯衍生物的电化学性能 .通过比较不同取代基的C60 衍生物的电化学性能 ,研究引入基团的结构特性与其得电子能力之间的关系     

敏化处理304不锈钢局部腐蚀行为的扫描微电极法研究

通过扫描微电极法研究敏化处理奥氏体不锈钢(304ss)的局部腐蚀行为,并结合传统电化学方法及光学显微镜进行测试观察. 结果表明,在10% FeCl3溶液未敏化处理(304ss-NS)或550 oC轻度敏化处理(304ss-S1)的不锈钢倾向于发生点腐蚀,而650 oC(304ss-S2)或750 oC(304ss-S3)深度敏化处理不锈钢则倾向于发生晶间腐蚀.     

海洋微生物对316不锈钢的电化学腐蚀行为

采用自腐蚀电位、电化学极化曲线、电化学阻抗谱技术研究了316不锈钢在无菌培养基介质和海水微生物接种培养有菌培养基介质中不同周期的腐蚀行为．结果表明,316不锈钢电极在有菌介质中比在无菌介质中的腐蚀电流密度大,腐蚀电位负移,微生物加速了不锈钢的腐蚀速度．随着浸泡时间的增加,有菌介质中的不锈钢电极极化电阻值逐渐减小,表明了海洋微生物的附着和繁殖加速了316不锈钢的腐蚀速率,降低了其在海洋环境中的耐蚀性．     

Electrochemical behavior of stainless steel in aerated NaCl solutions by electrochemical impedance and rotating disk electrode methods

Electrochemical behavior of stainless steel in 0.5 M NaCl solutions is studied. It is shown that, for this steel, under a considerable cathodic polarization of electrode, the oxygen electroreduction proceeds via a four-electron mechanism. The corrosion current is estimated. From the impedance spectra, elements of an equivalent circuit that describes the electrode behavior under the ac conditions are calculated. A mechanism of the steel passivation in the electrolyte is proposed.     

苯酚苯胺共聚物在304不锈钢电极表面的电化学合成及成膜微观结构分析

Electrochemical copolymerization of phenol and aniline was achieved on 304 stainless steel anodes in neutral water solution with an electrolyte of Na₂SO₄O₄. Compared with pit corro-sion potential of different copolymer coatings, the best solution composition was 0.09 mol/L phenol and 0.01 mol/L aniline. Through infrared spectrum analysis, polyaniline structure was proved in phenol-aniline copolymer, as well as more side chains. Scanning electron mi-croscope was used to analyze microstructure of copolymer coating, taking advantage of part solubility of phenol-aniline copolymer in tetrahydrofuran, the bifurcate network structure was observed. The copolymer coating microstructure was summarized, compared with the performance of polyphenol coatings, the reasons of corrosion resistance enhancement with the addition of aniline in electropolymerization reaction was assumed as well.     

Electrochemical behaviour of SiO2 sol-gel coatings on stainless steel

SiO₂ coatings onto stainless steel substrates have been prepared by sol-gel in order to study the performance and mechanism of attack in different corrosive solutions. The electrochemical behaviour of the samples has been evaluated by Electrochemical Impedance Spectroscopy using NaCl and HCl as electrolytes. Comparative tests have been performed on samples with one and two silica layers as well as on uncoated ones. SiO₂ coatings produce no important protection of stainless steels subjected to electrochemical corrosion. This behaviour may be explained by micropores and microcracks produced during the coating sintering.     

H2S环境中UNS J91540不锈钢的电化学行为对SCC的影响

应用慢应变速率拉伸试验和电化学方法研究了湿硫化氢溶液中UNS J91450不锈钢的电化学行为对应力腐蚀开裂的影响.结果表明,本实验条件下UNS J91540不锈钢具有较高的SCC敏感性,并随着溶液pH的降低而明显增大.该不锈钢的电化学行为对它的腐蚀开裂(SCC)敏感性具有重要影响.开路电位下该不锈钢的SCC行为同时受氢脆作用和裂纹尖端阳极溶解作用的影响.在pH较低的介质中析氢电流较高而裂纹尖端阳极溶解作用略低,而在pH较高的介质中析氢电流较低而裂纹尖端的阳极溶解作用相对增强.氢脆作用对UNS J91540不锈钢SCC敏感性影响更显著.     

An Electrochemical Study on the Corrosion Inhibition of Stainless Steel by Polyaniline Film

Polyaniline(PANI)film was electrosynthesized on 304 stainless steel by cyclic voltammetry using aqueous oxalic acid as supporting electrolyte.The potential sweep rates were changed to achieve the PANI film with different thickness and structures.Protective properties of the PANI film for corrosion of stainless steel in 3% NaC1 aqueous solution were investigated by monitoring potentiodynamic polarization curves and electrochemical impedance spectroscopy(EIS).The results showed that the PANI film which was formed with lower sweep rate led to more positive shift of corrosion potential and greater charge transfer resistance,reflecting higher inhibition for corrosion of the stainless steel.     

Electrochemical and XPS studies on corrosion behaviours of AISI 304 and AISI 316 stainless steels under plastic deformation in sulphuric acid solution

The corrosion behaviours of austenitic stainless steels were investigated by electrochemical methods under plastic deformation with constant strain in the naturally aerated 0.5 M H₂SO₄ + 0.2 M KCl solution at room temperature. The work addresses the influence of plastic deformation and molybdenum element on the corrosion resistance of austenitic stainless steels in the test solution. Electrochemical impedance spectroscopy presents the decreasing charge transfer resistance (R_t) and polarization resistance (R_p) values with the immersion time for AISI 304 stainless steel under constant strain deformation, and the increasing R_t and R_p values with the immersion time for AISI 316 stainless steel. The analysis of the chemical composition of the corrosion products was carried out by XPS. Molybdenum addition in AISI 316 stainless steel affects significantly the corrosion resistance because of its high ability to form Mo (VI) and MoCl₅ insoluble compounds in acid medium. Copyright © 2011 John Wiley & Sons, Ltd.     

镀银-石墨涂层316L不锈钢双极板的电化学性能测试及表征

316L不锈钢以其质轻,价廉,易加工成型以及良好的导电导热性能而成为极具潜力的质子交换膜燃料电池双极板材料,但其在电池运行环境中仍有一定缺陷.在阴极条件下不锈钢板易钝化,增加了与碳纸扩散层间的界面接触电阻;而在阳极条件下,则由于金属离子的溶解,污染了膜电极,引起催化剂中毒,从而降低电池输出功率,影响电池性能.本文采用喷涂技术在316L不锈钢表面制备导电石墨涂层,测得其与Toray060碳纸的接触电阻为80.6mΩ·cm2.如果在制备石墨涂层前预镀薄层银,则可使其接触电阻降至19.8mΩ·cm2.因此,本文利用Tafel曲线、恒电位氧化等电化学方法,对该镀银-石墨涂层316L不锈钢与原316L不锈钢和镀银316L不锈钢在模拟质子交换膜燃料电池阴、阳极工作环境条件下的耐腐蚀性能进行了研究.结果表明,镀银不锈钢和镀银-石墨涂层不锈钢较原不锈钢的腐蚀电位分别提高了0.49和0.35V,腐蚀电流密度下降1-2个数量级,维持在10-6-10-7A·cm-2.而镀薄银钢板则因为银层较薄存在微孔,使得部分不锈钢基体外露,形成腐蚀电池而更易于腐蚀.