Effects of deposition parameters on laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited on BK7 substrates by e-beam evaporation with different deposition parameters such as substrate temperature (323-623 K), oxygen pressure (0.5-3.0×10⁻² Pa) and deposition rate (0.2-0.5 nm/s). Absorption, scattering and chemical composition were investigated by surface thermal lensing (STL) technique, total integrated scattering (TIS) measurement and X-ray photoelectron spectroscopy (XPS), respectively. The laser-induced damage threshold (LIDT) was assessed using pulsed Nd:YAG 1064 nm laser at a pulse length of 12 ns. The results showed that optical properties, absorption and LIDT were influenced by the deposition parameters and annealing. However, scattering was little correlated with the deposition parameters. On the whole, the LIDT increased with increasing substrate temperature and oxygen pressure, whereas it increased firstly and then decreased upon increasing deposition rate. After annealing at 673 K for 12 h, the LIDT of films improved significantly. The dependence of possible damage mechanism on deposition parameters was discussed.     

Investigation of annealing effects on the laser-induced damage threshold of amorphous Ta2O5 films

Ta₂O₅ films were deposited using the conventional electron beam evaporation method and then annealed at temperatures in the range 373-673 K. Chemical composition, scattering and absorption were examined by X-ray photoelectron spectroscopy (XPS), total integrated scattering (TIS) measurement and the surface thermal lensing (STL) technique, respectively. The laser-induced damage threshold (LIDT) was assessed using the output from an Nd:YAG laser with a pulse length of 12 ns. The results showed that the improvement of the LIDT after annealing was due to the reduced substoichiometric and structural defects present in the film. The LIDT increased slightly below 573 K and then increased significantly with increase in annealing temperature, which could be attributed to different dominant defects. Moreover, the root mean square (RMS) roughness and scattering had little effect on the LIDT, while the absorption and the LIDT were in accord with a general relation.     

High temperature annealing effect on structure, optical property and laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited by conventional electron beam evaporation method and then annealed in air at different temperature from 873 to 1273 K. It was found that the film structure changed from amorphous phase to hexagonal phase when annealed at 1073 K, then transformed to orthorhombic phase after annealed at 1273 K. The transmittance was improved after annealed at 873 K, and it decreased as the annealing temperature increased further. The total integrated scattering (TIS) tests and AFM results showed that both scattering and root mean square (RMS) roughness of films increased with the annealing temperature increasing. X-ray photoelectron spectroscopy (XPS) analysis showed that the film obtained better stoichiometry and the O/Ta ratio increased to 2.50 after annealing. It was found that the laser-induced damage threshold (LIDT) increased to the maximum when annealed at 873 K, while it decreased when the annealing temperature increased further. Detailed damaged models dominated by different parameters during annealing were discussed.     

Influence of overcoat on laser-induced damage threshold of 532 and 800 nm TiO2/SiO2 high reflectors

TiO₂/SiO₂ high reflectors with and without a SiO₂ overcoat are deposited by electron-beam evaporation. The film properties are characterized by visible spectrometry measures, structure analysis, roughness and laser-induced damage threshold (LIDT) tests, surface defects and damage morphology observation. The effects of overcoats on LIDT at 532 nm, 8 ns and 800 nm, 220 ps laser pulses are investigated. The relations between film structure, roughness, surface defects, electric field and LIDT are discussed. It is found that overcoats can increase the LIDT at these two laser wavelengths. The reduction of peak temperature, the low defects density and roughness, the low intrinsic absorption of SiO₂ and its amorphous structure are the main reasons for LIDT improvement by overcoats.     

Annealing effects on structure and laser-induced damage threshold of Ta2O5/SiO2 dielectric mirrors

The effects of annealing on structure and laser-induced damage threshold (LIDT) of Ta₂O₅/SiO₂ dielectric mirrors were investigated. Ta₂O₅/SiO₂ multilayer was prepared by ion beam sputtering (IBS), then annealed in air under the temperature from 100 to 400 °C. Microstructure of the samples was characterized by X-ray diffraction (XRD). Absorption of the multilayer was measured by surface thermal lensing (STL) technique. The laser-induced damage threshold was assessed using 1064 nm free pulsed laser at a pulse length of 220 μs.

It was found that the center wavelength shifted to long wavelength gradually as the annealing temperature increased, and kept its non-crystalline structure even after annealing. The absorbance of the reflectors decreased after annealing. A remarkable increase of the laser-induced damage threshold was found when the annealing temperature was above 250 °C.     

Effects of deposition rates on laser damage threshold of TiO2/SiO2 high reflectors

TiO₂ single layers and TiO₂/SiO₂ high reflectors (HR) are prepared by electron beam evaporation at different TiO₂ deposition rates. It is found that the changes of properties of TiO₂ films with the increase of rate, such as the increase of refractive index and extinction coefficient and the decrease of physical thickness, lead to the spectrum shift and reflectivity bandwidth broadening of HR together with the increase of absorption and decrease of laser-induced damage threshold. The damages are found of different morphologies: a shallow pit to a seriously delaminated and deep crater, and the different amorphous-to-anatase-to-rutile phase transition processes detected by Raman study. The frequency shift of Raman vibration mode correlates with the strain in film. Energy dispersive X-ray analysis reveals that impurities and non-stoichiometric defects are two absorption initiations resulting to the laser-induced transformation.     

Emission features of Ho ion in Nb2O5, Ta2O5 and La2O3 mixed Li2O-ZrO2-SiO2 glasses

Li₂O-ZrO₂-SiO₂: Ho³⁺ glasses mixed with three interesting d-block elemental oxides, viz., Nb₂O₅, Ta₂O₅ and La₂O₃, were prepared. Optical absorption and photoluminescence spectra of these glasses have been recorded at room temperature. The luminescence spectra of Nb₂O₅ and Ta₂O₅ mixed Li₂O-ZrO₂-SiO₂ glasses (free of Ho³⁺ ions) have also exhibited broad emission band in the blue region. This band is attributed to radiative recombination of self-trapped excitons (STEs) localized on substitutionally positioned octahedral Ta⁵⁺ and Nb⁵⁺ ions in the glass network. The Judd-Ofelt theory was successfully applied to characterize Ho³⁺ spectra of all the three glasses. From this theory various radiative properties, like transition probability A, branching ratio β_r and the radiative lifetime τ_r, for ⁵S₂ emission levels in the spectra of these glasses have been evaluated. The radiative lifetime for ⁵S₂ level of Ho³⁺ ions has also been measured and quantum efficiencies were estimated. Among the three glasses studied the La₂O₃ mixed glass exhibited the highest quantum efficiency. The reasons for such higher value have been discussed based on the relationship between the structural modifications taking place around the Ho³⁺ ions.     

Structure and optical analysis of Ta2O5 deposited on infrasil substrate

Electron beam gun technique was used to prepare Ta₂O₅ thin films onto infrasil substrates of thicknesses 333 and 666 nm. The structure characterization was investigated using X-ray diffraction patterns. Transmittance measurements in the wavelength range (240-2000 nm) were used to calculate the refractive index n and the absorption index k depending on Swanepole's method. The dispersion curve of the refractive index shows an anomalous dispersion in the absorption region and a normal one in the transparent region. The analysis of the optical absorption data revealed that the optical band gap E_g was indirect transition. It was found that the refractive index dispersion data obeyed the single oscillator of the Wemple-DiDomenico model, from which the dispersion parameters (E_o and E_d) and the high frequency dielectric constant were determined. The electric free carrier susceptibility and the carrier concentration to the effective mass ratio were estimated according to the model of Spitzer and Fan. Graphical representation of the relaxation time as a function of photon energy was also presented.     

Modification of laser induced damage threshold of ZrO2 thin films by using time-temperature gradient annealing

As a result of using time-temperature gradient annealing, the structural and optical properties and hence, thermal properties of ZrO₂ thin films deposited by electron gun, enhanced considerably compared with rapid thermal annealing. Also, it can be seen time- temperature gradient annealing caused to decrease the total stress and number of thermal barrier along the film. Therefore, according to our experimental results, which is agree with theoretical analysis, the laser induced damage threshold of ZrO₂ films can be enhanced significantly compared with rapid annealing procedure.     

Electrical and material characterization of tantalum pentoxide (Ta2O5) charge trapping layer memory

In this experiment, tantalum pentoxide (Ta₂O₅) was used in a metal/oxide/high-k Ta₂O₅/oxide/silicon (MOHOS) novel nanocrystal memory as a trapping layer. Post-annealing treatment, which can passivate defects and improve the material quality of the high-k dielectric, was applied to optimize device performance for a better memory window and faster P/E (program/erase) cycle. Material and electrical characterization techniques including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and electrical measurements were performed to analyze the device under different annealing conditions. The Ta₂O₅ charge trapping layer memory annealed at 900 °C had a higher window of 3.3 V in the current-voltage (C-V) hysteresis loop, and a higher charge retention capability than the samples prepared under various annealing conditions. These higher levels were due to the higher probability of deep-level charge trapping and lower leakage current.     

Effects of Ta2O5 addition on the microstructure and temperature dependence of magnetic properties of MnZn ferrites

MnZn ferrites with the chemical formula Mn_0.68Zn_0.25Fe_2.07O₄ have been prepared by the conventional ceramic technique. Toroidal cores were sintered at 1350 °C for 4 h in N₂/O₂ atmosphere with 4% oxygen. Then the influence of Ta₂O₅ addition on the microstructure and temperature dependence of magnetic properties of MnZn ferrites was investigated by characterizing the fracture surface micrograph and measuring the magnetic properties over a temperature ranging from 25 to 120 °C. The results show that, when the Ta₂O₅ concentration is not more than 0.04wt%, the grain size has a slight increase with the increase of Ta₂O₅ concentration, the temperature of secondary maximum peak in the curve of initial permeability versus temperature and the lowest power loss shift to lower temperature. However, excessive Ta₂O₅ concentration (>0.04wt%) results in the exaggerated grain growth and porosity increase, which make the initial permeability and saturation magnetic flux density decrease and the power loss increase at room temperature. Furthermore, the temperature of secondary maximum peak in the curve of initial permeability versus temperature and the lowest power loss shift to about 100 °C.     

Effects of O2/Ar ratio and annealing temperature on electrical properties of Ta2O5 film prepared by magnetron sputtering

The effects of the oxygen-argon ratio on electric properties of Ta2O5 film prepared by radio-frequency magnetron sputtering were investigated.The Ta2O5 partially transforms from the amorphous phase into the crystal phase when annealing temperatures are 800℃ or higher.The lattice constant of Ta2O5 decreases with the increase of the O2/Ar ratio,which indicates that oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies during the deposition process.For the films deposited in working gas mixtures with different O2/Ar ratios and subsequently annealed at 700℃,the effective dielectric constant is increased from 14.7 to 18.4 with the increase of the O2/Ar ratio from 0 to 1.Considering the presence of an SiO2 layer between the film and the silicon substrate,the optimal dielectric constant of Ta2O5 film was estimated to be 31.Oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies,and the oxygen vacancy density and leakage current of Ta2O5 film both decrease with the increase of the O2/Ar ratio.The leakage current decreases after annealing treatment and it is minimized at 700℃.However,when the annealing temperature is 800℃ or higher,it increases slightly,which results from the partially crystallized Ta2O5 layer containing defects such as grain boundaries and vacancies.     

Annealing effects on the optical and structural properties of Al2O3/SiO2 films as UV antireflection coatings on 4H-SiC substrates

Al₂O₃/SiO₂ films have been prepared by electron-beam evaporation as ultraviolet (UV) antireflection coatings on 4H-SiC substrates and annealed at different temperatures. The films were characterized by reflection spectra, ellipsometer system, atomic force microscopy (AFM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. As the annealing temperature increased, the minimum reflectance of the films moved to the shorter wavelength for the variation of refractive indices and the reduction of film thicknesses. The surface grains appeared to get larger in size and the root mean square (RMS) roughness of the annealed films increased with the annealing temperature but was less than that of the as-deposited. The Al₂O₃/SiO₂ films maintained amorphous in microstructure with the increase of the temperature. Meanwhile, the transition and diffusion in film component were found in XPS measurement. These results provided the important references for Al₂O₃/SiO₂ films annealed at reasonable temperatures and prepared as fine antireflection coatings on 4H-SiC-based UV optoelectronic devices.     

渐变折射率Ta_2O_5/SiO_2薄膜多脉冲激光损伤特性

采用离子束溅射(IBS)的方式,制备了1064nm高反射Ta2O5/SiO2渐变折射率光学薄膜。对其光学性能和在基频多脉冲下抗损伤性能进行了分析。通过渐变折射率的设计方式,很好地抑制了边带波纹,增加了1064nm反射率。通过对损伤阈值的分析发现,随着脉冲个数的增加,损伤阈值下降明显;但是在20个脉冲数后,损伤阈值(维持在22J/cm2左右)几乎保持不变直到100个脉冲数。通过Leica显微镜对损伤形貌的观察,发现损伤诱因是薄膜表面的节瘤缺陷。通过扫描电镜(SEM)以及聚集离子束(FIB)对薄膜表面以及断面的观察,证实了薄膜的损伤起源于薄膜表面的节瘤缺陷。进一步研究得出,渐变折射率薄膜在基频光单脉冲下损伤主要是由初始节瘤缺陷引起的,在后续多脉冲激光辐照下初始节瘤缺陷引起烧蚀坑的面积扩大扫过薄膜上的其他节瘤缺陷,引起了其他节瘤缺陷的喷射使损伤加剧,造成损伤的"累积效应"。     

Analysis of material modifications induced during laser damage in SiO2 thin films

The damage mechanisms in silica thin films exposed to high fluence 1064 nm nano-second laser pulses are investigated. The thin films under study are made with different techniques (evaporation and sputtering, with and without ion assistance) and the results are compared. The material morphological, optical and structural modifications are locally analyzed with optical microscopy and profilometry, photoluminescence and absorption microscopies. These observations are made for fluences near and above the laser damage threshold, and also in the case of multiple pulse irradiations. An increase in absorption in and around the damages is observed, as well as the generation of different defects that we spatially resolve with absorption and luminescence mappings.     

XPS investigation of diffusion of two-layer ZrO2/SiO2 and SiO2/ZrO2 sol–gel films

Two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were deposited on K9 glass substrates by sol–gel dip coating method. X-ray photoelectron spectroscopy (XPS) technique was used to investigate the diffusion of ZrO₂/SiO₂ and SiO₂/ZrO₂ films. To explain the difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films, porous ratio and surface morphology of monolayer SiO₂ and ZrO₂ films were analyzed by using ellipsometry and atomic force microscopy (AFM). We found that for the ZrO₂/SiO₂ films there was a diffusion layer with a certain thickness and the atomic concentrations of Si and Zr changed rapidly; for the SiO₂/ZrO₂ films, the atomic concentrations of Si and Zr changed relatively slowly, and the ZrO₂ layer had diffused through the entire SiO₂ layer. The difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films was influenced by the microstructure of SiO₂ and ZrO₂.     

A facile synthesis of monodisperse CoFe2O4/SiO2 nanoparticles

Aminated-CoFe₂O₄/SiO₂ magnetic nanoparticles (NPs) were prepared from primary silica particles using modified StÖber method. By optimizing the preparation conditions, monodisperse CoFe₂O₄/SiO₂ NPs with high amino groups’ density were obtained, which is necessary for enzyme immobilization. TEM confirm that the sample is a core/shell structure. These aminated-CoFe₂O₄/SiO₂ NPs have narrow size distributions with a mean size of about 60 nm. Moreover, the aminated-CoFe₂O₄/SiO₂ NPs can be easily dispersed in aqueous medium. The experimental results also show that the NPs have superparamagnetism, indicating that the aminated-CoFe₂O₄/SiO₂ NPs can be used as an effective carrier for the enzyme immobilization.     

渐变折射率Ta2O5/SiO2薄膜多脉冲激光损伤特性

采用离子束溅射（IBS）的方式,制备了1064 nm高反射Ta2O5/SiO2渐变折射率光学薄膜。对其光学性能和在基频多脉冲下抗损伤性能进行了分析。 通过渐变折射率的设计方式,很好地抑制了边带波纹,增加了1064 nm反射率。通过对损伤阈值的分析发现,随着脉冲个数的增加,损伤阈值下降明显;但是在20个脉冲数后,损伤阈值（维持在22 J/cm2左右）几乎保持不变直到100个脉冲数。通过Leica显微镜对损伤形貌的观察,发现损伤诱因是薄膜表面的节瘤缺陷。通过扫描电镜（SEM）以及聚集离子束（FIB）对薄膜表面以及断面的观察,证实了薄膜的损伤起源于薄膜表面的节瘤缺陷。进一步研究得出,渐变折射率薄膜在基频光单脉冲下损伤主要是由初始节瘤缺陷引起的,在后续多脉冲激光辐照下初始节瘤缺陷引起烧蚀坑的面积扩大扫过薄膜上的其他节瘤缺陷,引起了其他节瘤缺陷的喷射使损伤加剧,造成损伤的累积效应。     

制备工艺对HfO2薄膜抗激光损伤能力的影响

采用反应蒸镀法镀制了单层HfO2薄膜,观察了薄膜表面主要的微结构缺陷,研究了基片清洗工艺对薄膜损伤阈值的影响。测量了薄膜沉积前后表面粗糙度变化。结果表明：沉积工艺可以改变粗糙度,并对薄膜抗激光损伤能力有较大的影响。     

Deposition and characterization of binary Al2O3/SiO2 coating layers on the surfaces of rutile TiO2 and the pigmentary properties

Binary Al₂O₃/SiO₂-coated rutile TiO₂ composites were prepared by a liquid-phase deposition method starting from Na₂SiO₃·9H₂O and NaAlO₂. The chemical structure and morphology of binary Al₂O₃/SiO₂ coating layers were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, TG-DSC, Zeta potential, powder X-ray diffraction, and transmission electron microscopy techniques. Binary Al₂O₃/SiO₂ coating layers both in amorphous phase were formed at TiO₂ surfaces. The silica coating layers were anchored at TiO₂ surfaces via Si-O-Ti bonds and the alumina coating layers were probably anchored at the SiO₂-coated TiO₂ surfaces via Al-O-Si bonds. The formation of continuous and dense binary Al₂O₃/SiO₂ coating layers depended on the pH value of reaction solution and the alumina loading. The binary Al₂O₃/SiO₂-coated TiO₂ composites had a high dispersibility in water. The whiteness and brightness of the binary Al₂O₃/SiO₂-coated TiO₂ composites were higher than those of the naked rutile TiO₂ and the SiO₂-coated TiO₂ samples. The relative light scattering index was found to depend on the composition of coating layers.