聚N-异丙基丙烯酰胺/纳米SiO2复合水凝胶的合成及溶胀性能

通过纳米SiO2的表面功能化,在其表面引入乙烯基功能基团,在H2O／THF的混合溶剂中,超声分散后,交联剂N,N′-亚甲基双丙烯酰胺存在时,于25℃下使其与N-异丙基丙烯酰胺共聚,制得聚N-异丙基丙烯酰胺,纳米SiO2复合水凝胶,并用FT-IR和SEM对产物进行了表征,研究了凝胶的溶胀动力学,消溶胀动力学和温度敏感性,实验结果表明,纳米SiO2的引入,改善了聚N-异丙基丙烯酰胺水凝胶在低温时的溶胀性能和在高温时对水的释放性能,并讨论了引起这些性能改变的原因。     

多孔聚N-异丙基丙烯酰胺水凝胶的制备与缓释性能

以N-异丙基丙烯酰胺(NIPA)、N,N-亚甲基双丙烯酰胺(MBA)和聚乙二醇(PEG)为原料,以60Co-γ射线为放射源制备了快速响应聚N-异丙基丙烯酰胺(PNIPA)多孔水凝胶。用红外光谱分析了水凝胶的结构,并测定了水凝胶的溶胀动力学、退溶胀动力学和平衡溶胀率。结果表明,PEG分子仅在聚合交联过程中充当成孔剂,不参与反应,反应后可被除去;水凝胶具有明显的温度敏感性,成孔剂的添加提高了水凝胶的溶胀性能和LCST。选用阿司匹林为模型药物,对水凝胶的药物缓释性能进行了初步研究。     

聚(N,N′-二乙基丙烯酰胺)水凝胶的制备及其溶胀动力学

以N,N′-二乙基丙烯酰胺(DEA)为单体,偶氮二异丁腈(AIBN)为引发剂,分别采用疏水性的1,2-二乙烯苯(DVB)和水溶性的N,N′-亚甲基双丙烯酰胺(BIS)为交联剂制备了温度敏感水凝胶聚(N,N′-二乙基丙烯酰胺)(PDEA).制得的PDEA水凝胶的低临界溶解温度(LCST)在30 ℃附近,初步讨论了交联剂的用量和性质对水凝胶性能的影响.并对其在不同温度下达到溶胀平衡时的溶胀比,去溶胀动力学及干凝胶的再溶胀动力学过程进行了研究.     

纤维素纳米纤维接枝聚(N-异丙基丙烯酰胺)水凝胶的制备与表征

将具有温度响应的聚N-异丙基丙烯酰胺(PNIPAm)接枝到电纺纤维素纳米纤维膜上,制备温度响应型纤维素接枝聚N-异丙基丙烯酰胺(PNIPAm-g-Cell)纳米纤维水凝胶。 研究接枝单体(N)与纤维素(c)的质量比、反应温度、反应时间和引发剂浓度对产物接枝率、溶胀性和形貌的影响。 结果表明,最佳聚合反应条件为m(N):m(c)=15:1、反应温度40 ℃、反应时间3 h、引发剂浓度为10 mmol/L,得到PNIPAm-g-Cell接枝率和溶胀率分别为35%和31%。 与PNIPAm相比,PNIPAm-g-Cell水凝胶的低临界相转变温度(LCST)显著升高,说明亲水性纤维素的引入改变了体系的亲疏水平衡。 去溶胀动力学测试表明,0.5 min内接枝率为25%和35%的水凝胶保水率分别降低至93%和61%。 说明接枝率越高PNIPAm-g-Cell水凝胶对温度的响应速度越快,对温度越敏感。     

快速温度敏感聚(N-异丙基丙烯酰胺-co-丙烯酰胺)水凝胶的制备及性能研究

于 4 8℃下制备快速温度敏感聚 ( N -异丙基丙烯酰胺 -co-丙烯酰胺 )水凝胶 ,其在室温具有较大的平衡溶胀率 .通过改变丙烯酰胺的含量可以调节水凝胶的较低临界溶解温度     

聚（N，N＇-二乙基丙烯酰胺）水凝胶的制备及其溶胀动力学

以N,N’-二乙基丙烯酰胺（DEA）为单体,偶氮二异丁腈（AIBN）为引发剂,分别采用疏水性的1,2-二乙烯苯（DVB）和水溶性的N,N’-亚甲基双丙烯酰胺（BIS）为交联剂制备了温度敏感水凝胶聚（N,N’-二乙基丙烯酰胺）（PDEA）。制得的PDEA水凝胶的低临界溶解温度（LCST）在30℃附近,初步讨论了交联剂的用量和性质对水凝胶性能的影响。并对其在不同温度下达到溶胀平衡时的溶胀比,去溶胀动力学及干凝胶的再溶胀动力学过程进行了研究。     

光化学合成P(DMAA-co-MMA)/Nano-SiO2复合水凝胶及其性能研究

以N,N-二甲基丙烯酰胺(DMAA)及甲基丙烯酸甲酯(MMA)为单体,Irgacure 2959为光引发剂,N,N′-二甲基双丙烯酰胺(Bis)为交联剂,利用紫外光引发自由基聚合制备了聚N,N′-二甲基丙烯酰胺(PDMAA)及P(DMAA-co-MMA)水凝胶,并通过加入少量表面改性后的纳米SiO₂对该水凝胶进行改性,制得了P(DMAA-co-MMA)/纳米SiO₂复合水凝胶,用FT-IR和SEM对产物进行了表征,同时研究该复合凝胶的溶胀动力学、消溶胀动力学、pH值响应性、离子强度等.该方法简便、快捷,大大缩短了聚合时间,合成过程仅需2-3 min.     

明胶-聚异丙基丙烯酰胺水凝胶的溶胀动力学

采用明胶（Gel)和N－异丙基丙烯酰胺（NIPAM）为原料，制备了Gel/聚异丙基丙烯酰胺（PNIPAM）水凝胶系列；研究了原料配比、pH值及温度对水凝胶溶胀速度的影响。结果表明，当温度大于PNIPAM的最低临界溶液温度（LCST）值时，Gel/PNIPAM水凝胶的溶胀速度随着组分中PNIPAM的增加而降低，且溶胀过程以扩散渗透控制为主。而pH对水凝胶溶胀速度的影响与温度有关。Gel/PNIPAM配比为5／5，温度大于LCST时，水凝胶的pH敏感性受明胶控制；温度低于LCST时，pH对水凝胶的溶胀速度的影响很小。     

pH敏感水凝胶聚甲基丙烯酸的超声合成

在超声作用下,以甲基丙烯酸为原料,N,N’-亚甲基双丙烯酰胺为交联剂,过硫酸钾为引发剂,自由基引发聚合制备了pH敏感水凝胶聚甲基丙烯酸,采用红外光谱(FT-IR)和扫描电镜(SEM)对水凝胶分子结构与性能进行表征.在此基础上,重点研究了超声合成对于水凝胶的溶胀性能、消溶胀性能等性质的影响.实验结果表明,超声作用下合成的聚甲基丙烯酸水凝胶溶胀动力学性能以及响应灵敏性均优于常规合成方法.     

丝素蛋白纤维/聚N-异丙基丙烯酰胺复合水凝胶的性能

以丝素蛋白纤维为填充材料,采用自由基聚合的方法制备复合聚N-异丙基丙烯酰胺(PNIPPAm)水凝胶,研究复合水凝胶的黏弹性能、溶胀性能和反复溶胀-收缩性能。结果表明:丝素蛋白纤维的加入改善了复合水凝胶的力学性能,其平衡溶胀率不仅与温度有关,而且与丝素蛋白纤维的含量有关。此外,处在表面的丝素蛋白纤维与水凝胶之间存在间隙,在反复溶胀-收缩过程中可以作为输水通道,有利于水分子进出,提高了PNIPPAm水凝胶对温度的响应速率并使其溶胀-收缩重复性更好。     

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征;N-异丙基丙烯酰胺;水凝胶;温敏性;快速响应     

生物可降解温度敏感性水凝胶用于甲状旁腺相关肽的可控释放

通过以两端带有碳碳双键的聚己内酯为生物可降解交联剂,N-异丙基丙烯酰胺为单体,通过自由基共聚合成了生物可降解的温度敏感性水凝胶,研究了此水凝胶体系在不同温度下的溶胀率及通过对其透光率的测试研究了水凝胶体系的温度响应性.以此水凝胶体系作为载体研究了PTHrP1-34(甲状旁腺相关肽)在不同温度下的体外药物释放行为.体外模拟释放表明,此水凝胶载药体系能实现PTHrP 1-34长达13天的持续释放,基于PTHrP1-34具有能够增加成骨细胞活性和数量并能促进骨形成的作用,同时这种有益效果取决于低剂量及间歇给药的方式.     

Synthesis and properties of a temperature-sensitive chelating hydrogel and its metal complexes

A temperature-sensitive chelating hydrogel was synthesized by the copolymerization of 1-(β-acrylamidoethyl)-3-hydroxy-2-methyl-4(1H)-pyridinone (AHMP) and N-isopropylacrylamide (NIPAA) in the presence of N,N' -ethylene-bis-acrylamide as a crosslinking agent. The AHMP-NIPAA hydrogel formed a red complex with iron(III) and a pale green complex with Cu(II), respectively. It was observed that the hydrogel and its metal complexes had a high swelling ratio below the temperature of 35°C, while above that temperature the swelling ratios were dramatically decreased. Furthermore, the swelling ratio of the metal complexes was much lower at the swelling temperature (below 35°C) than that of the hydrogel itself, which might be due to the lower flexibility of the complexes. The iron(III) chelating study showed that the hydrogel had a high chelating efficiency at its swelling temperature, while the chelating efficiency of the hydrogel was very low at its deswelling temperature (>35°C). It was found that the chelating efficiency depended on the swelling ratio of the hydrogel in water, which could be explained by the difference in contactable internal surfaces at different temperatures. The hydrogel and its metal complexes could be easily separated at their deswelling temperature. It was also convenient to regenerate the hydrogel with 1 M HCl for reuse.     

光化学合成快速响应聚(N,N-二甲基丙烯酰胺-co-N-异丙基丙烯酰胺)水凝胶

通过光化学合成方法分别在高温(50℃)和室温(28℃)下实现了N,N-二甲基丙烯酰胺(DMAA)和N-异丙基丙烯酰胺(NIPAm)的交联共聚,制备了两种不同结构的P(DMAA-co-NIPAm)共聚物水凝胶.对两种温度下制备的P(DMAA-co-NIPAm)共聚物水凝胶的网络结构、溶胀与消溶胀速率和温度敏感性等方面进行了比较研究.结果发现,50℃下制备的P(DMAA-co-NIPAm)共聚物凝胶具有较为疏松的网络结构和相对较快的溶胀速率及温度响应特性.光化学合成方法较传统的热聚合制备方法具有简便、快捷的特点,合成过程仅需2 min.     

Chemically Crosslinked pH- and Temperature-Sensitive (N-isopropylacrylamide-co-1-vinyl-2-pyrrolidone) Based on New Crosslinker: I. Swelling Behavior

Novel pH- and temperature-sensitive polymer matrices based on N-isopropylacrylamide have been developed. The hydrogels were prepared by bulk radical polymerization of N-isopropylacrylamide and 1-vinyl-2-pyrrolidinone in appropriate amounts of distilled water using different mol% of traditional N,N-methylene bisacrylamide (MBA) and the new synthesized N,N,N-tris acryloyl melamine (MAAm) crosslinkers. Lower critical solution transition temperatures (LCST) were measured by differential scanning calorimetry. The synthesized hydrogels have LCST lower than 40°C. The influence of environmental conditions such as temperature and pH on the swelling behavior of these polymeric gels was investigated. The swelling behaviors of the resulting gels show pH sensitivity. The crosslinked NIPAAm/VP with MAAm hydrogels exhibited more rapid deswelling rate than NIPAAm/VP hydrogels crosslinked with MBA in pure water in response to abrupt temperature changes from 20°C to 50°C.     

辐射交联制备改性CMC水凝胶的溶胀行为研究

利用丙烯酰胺 (AAm)接枝改性纤维素 ,然后进行羧甲基化反应得到高取代度的丙烯酰胺 羧甲基纤维素钠 (AAm CMC Na) .对该材料进行γ射线辐照制备出新型改性CMC水凝胶 .研究了这种水凝胶的溶胀动力学、交联动力学以及温度、pH值和无机盐浓度对水凝胶溶胀行为的影响 ,并与CMC Na水凝胶进行了比较 .结果表明 ,该水凝胶和CMC Na水凝胶相比 ,优点在于辐照交联所用的剂量下降 ,而且所需的CMC浓度减少 .AAm CMC Na水凝胶的溶胀度随温度升高而增大 ,在pH为 6～ 8范围内达到最大值 ,并随无机盐浓度与吸收剂量增加而下降 ,表现出较好的温度敏感性和pH敏感性 ,可望作为吸水材料和水保持剂     

Synthesis and Characterization of Hydrogels Based on Gamma Radiation Copolymerization of N‐isopropylacrylamide and Ethylene Glycol Dimethacrylate Monomers

Hydrogels based essentially on N‐isopropylacrylamide (NIPAAm) and different ratios of ethylene glycol dimethacrylate (EGDMA) monomer were synthesized by gamma radiation copolymerization. The thermal decomposition behavior of NIPAAm/EGDMA hydrogels was determined by thermogravimetric analysis (TGA). The effect of temperature and pH on the swelling behavior was also studied. The results showed that the ratio of EGDMA in the comonomer feeding solution has a great effect on the yield product, gel fraction and water content in the final hydrogel. In this regard, it was observed that the increase of EGDMA ratio decreased these properties. The TGA study showed that all the compositions of NIPAAm/EGDMA hydrogels displayed higher thermal stability than the hydrogel based on pure PNIPAAm hydrogel. The swelling kinetics in water showed that pure PNIPAAm and NIPAAm/EGDMA hydrogels reached equilibrium after 6 h. However, NIPAAm/EGDMA hydrogels show swelling in water lower than pure PNIPAAm. The results showed that the swelling character of pure PNIPAAm and NIPAAm/EGDMA hydrogels was affected by the change in temperature within the temperature range 25–40°C, and showed a reversible change in swelling in the pH range 4–7 depending on composition.     

疏水改性智能水凝胶P(NIPA-co-DiAB)的合成及其温敏行为

以N-异丙基丙烯酰胺(NIPA)和N,N-双烯丙基苄胺(DiAB)为共聚单体、N,N-亚甲基双丙烯酰胺(BIS)为交联剂、十二烷基硫酸钠(SDS)为表面活性剂、过硫酸铵(APS)-四甲基乙二胺(TMEDA)为氧化还原引发体系,采用自由胶束交联共聚法合成了疏水基团为芳香基的疏水改性温敏性智能水凝胶P(NIPA-co-DiAB)。研究了DiAB摩尔分数(x(DiAB))对水凝胶溶胀性能的影响。 在初始溶胀阶段,随着x(DiAB)由0增大至3%,P(NIPA-co-DiAB)水凝胶的溶胀行为由Fickian扩散转变为non-Fickian扩散。x(DiAB)分别为0、1%、2%和3%时,P(NIPA-co-DiAB)水凝胶的平衡溶胀率SR0在蒸馏水中分别为63.6、93.5、141.6和167.4,在0.01 mol/L SDS溶液中分别为63.1、71.0、59.0和77.5,在CTAB溶液中分别为37.6、42.2、44.1和60.0,在Triton X-100溶液中分别为30.9、49.4、68.5和88.3。 结果表明,P(NIPA-co-DiAB)水凝胶的(SR0)大于PNIPA水凝胶,且在蒸馏中比在0.01 mol/L表面活性剂溶液中要大。 加入0.01 mol/L Triton X-100、CTAB或SDS后,PNIPA水凝胶的体积相变温度或较低临界溶解温度(LCST)由32.5 ℃分别增加至35.4、45.6和80 ℃。P(NIPA-co-DiAB)水凝胶的LCST由32.0～32.5 ℃分别增加至34.7～35.6 ℃、45.8~46.2 ℃和80 ℃。 加入表面活性剂能增加P(NIPA-co-DiAB)水凝胶的体积相变温度,高的体积相变温度与DiAB含量无关。     

Temperature-sensitive polyamidoamine dendrimer/poly(N-isopropylacrylamide) hydrogels with improved responsive properties

Novel temperature-sensitive poly(N-isopropylacrylamide)/amine-terminated polyamidoamine dendrimer G6-NH2 hydrogels with fast responsive properties were synthesized by forming semi-interpenetrating polymeric networks. In contrast to the conventional PNIPA hydrogel, these new gels showed rapid shrinking rate at the temperature above lower critical solution temperature (LCST), and exhibited higher equilibrium swelling ratio at room temperature. All these properties might be attributed to the incorporation of polyamidoamine dendrimer G6-NH2, which forms water-releasing channels and increases the hydrophilicity of PNIPA network. The novel hydrogels have potential applications in drug and gene delivery.     

温度及pH敏感聚(丙烯酸)-co-(丙烯腈)水凝胶的合成及性能研究

温度及ｐＨ敏感聚（丙烯酸） ｃｏ （丙烯腈）水凝胶的合成及性能研究卓仁禧张先正（武汉大学化学系国家教委生物医用高分子材料开放实验室武汉４３００７２）关键词丙烯酸，丙烯腈，水凝胶，溶胀率关于水凝胶的环境敏感性研究始于八十年代初［１］．随后大量研究表明...