新型蒽衍生物蓝光材料的合成及光电性能研究

通过引入具有电子传输性能的噁二唑衍生物支链,采用Suzuki偶联反应,设计并合成了一种新型的蒽衍生物蓝光材料,同时研究了它的光学性能、热学性能、电化学性能以及成膜性。研究结果表明,该化合物在四氢呋喃溶液中发射蓝色荧光,最大发射波长为433 nm,其荧光量子效率为0.94,是9,10-二（β-萘基）蒽（ADN）的1.17倍。该化合物薄膜经过100 ℃高温烘烤3 h,依然保持连续、均一、平整的无定型结构,是制备长寿命、高效率OLED的很有潜力的材料。     

新型蓝光材料9,9'-联蒽衍生物的合成及其光电性能

通过引入不同的取代基,采用Suzuki偶联反应,合成了一系列9,9'-联蒽衍生物新型蓝光材料,并研究了它们的紫外-可见吸收、荧光发射、荧光量子效率和电化学等性能.研究结果表明,这些化合物在二氯甲烷中均发射蓝色荧光,与9,9'-联蒽相比,其荧光发射峰均红移了7 nm,达到453 nm,是典型的蓝色荧光,同时也具有较高的荧...     

2,7-二(3-(氰基)苯基)-9,9-二乙基芴的合成、晶体结构及光学性质(英文)

合成了一种新型的芴类衍生物2,7-二(3-(氰基)苯基)-9,9-二乙基芴。通过元素分析、红外(IR)、核磁共振(1H NMR)以及X射线单晶衍射对其组成和结构进行了表征。结果表明该化合物属于正交晶系,P空间群,晶胞参数:a=1.380 0(3)nm,b=2.230 6(4)nm,c=0.726 33(15)nm,α=β=γ=90°,V=2.235 8(8)nm3,Z=4,F(000)=896,μ=0.073 mm-1,S=1.013,R=0.046 9,wR=0.104 2。同时,我们对该化合物的紫外-可见吸收光谱和荧光光谱做了研究。在室温下,当激发光波长为330 nm时,该化合物的固态薄膜发射强烈的蓝色荧光,其发射波长为408 nm。此芴类衍生物在CH2Cl2溶液中的荧光量子效率为0.64,在固态薄膜中的斯托克斯位移为56 nm。该化合物有望成为一种优良的蓝色发光材料。     

两种蒽衍生物类深蓝光材料的合成与发光性能

利用Suzuki偶合反应合成了两种新的蒽衍生物9,10-二(2-联苯基)蒽(BBPA)和9,10-二[2-(α-萘基)苯基]蒽(BNPA),化合物结构通过核磁、质谱及元素分析进行了表征。量子化学计算结果显示,这两种化合物都具有非共面的分子结构,光物理性能主要决定于分子中的蒽结构单元。这两种化合物在二氯甲烷溶液中均可发射高效率的蓝光。BBPA在固态薄膜状态下的发射光谱相对其二氯甲烷溶液的发射光谱明显变宽,而BNPA的固态薄膜并未发生光谱变宽现象。分别利用化合物BBPA和BNPA作为发光层材料,制备出了非掺杂的深蓝光电致发光器件。发光层为BBPA的电致发光器件的最大外量子效率和CIE色坐标分别为2.48%和(0.16,0.09);基于BNPA的电致发光器件的最大外量子效率为2.68%,CIE色坐标为(0.15,0.07)。所制备的这两种器件均表现出了较低的开启电压和良好的稳定性。     

二苯乙烯衍生物的制备及结构-光学性能关系的研究

有机共轭材料由于在电子、非线性光学和发光领域具有广泛应用,引起人们广泛兴趣。苯乙烯衍生物是一类重要的有机共轭化合物。文章采用相转移Wittig反应和钯催化Heck反应合成了三种不同取代基二苯乙烯衍生物。研究了分子结构与电子吸收光谱和材料发光性能关系。同没有取代基的化合物3a相比(电子最大吸收峰波长358 nm),化合物3c中CH₃取代导致电子吸收光谱轻微红移到356 nm,硝基取代的化合物3b呈现出更大的吸收光谱红移现象,电子吸收最大峰红移到388 nm。同时发现：CH₃取代的化合物3c产生荧光发射峰在414 nm,同没有取代基的化合物3a相比,荧光发射强度明显增强;相反具有吸电子NO₂取代基的化合物3b荧光发射峰位于525 nm, 荧光发射强度明显减弱。可见二苯乙烯分子中取代基结构对分子光学性能产生重要影响。这为发光材料的分子设计提供新的思路。     

两种新型芴衍生物的合成、晶体结构及光谱性能

合成了两种新型芴衍生物:2,7-二(3,5-二(三氟甲基)苯基)-9,9-二乙基芴(1)和2,7-二(4-氟苯基)-9,9-二乙基芴(2)。通过元素分析、红外光谱(IR)、核磁共振氢谱(1H NMR)以及单晶X射线衍射对其结构进行了表征。化合物1属于单斜晶系,P21/c空间群;化合物2属于三斜晶系,P-1空间群。通过紫外-可见吸收和荧光光谱研究了化合物的发光性能。结果表明:在CH2Cl2溶液和固态薄膜中,化合物1、2在350~400 nm波段有吸收峰,归属于π-π*电荷跃迁;化合物1、2的光学带隙E g分别为3.31 eV和3.30 eV,并且均有强烈的蓝色荧光发射现象(激发波长为330 nm),在二氯甲烷中的荧光量子效率分别为0.62和0.61,固态荧光寿命分别为6.39 ns和9.00 ns。     

一种新的有机光致变色及热致变色化合物间氨基苯甲酸缩3,5二氯水杨醛希夫碱

制备了间氨基苯甲酸缩3,5-二氯水杨醛希夫碱,利用红外(IR)、核磁(¹H NMR)、质谱(MS)和元素分析对化合物结构进行了表征。研究了它的荧光性质和热稳定性。对化合物的紫外可见(UV-Vis)光谱和荧光光谱的研究表明,该化合物在DMF溶液中具有较好的光致变色和热致变色性能。化合物的吸光度值和最大发射波长与时间或温度呈线性关系,进一步说明该化合物是性能良好的光致变色及热致变色材料。     

新型吡唑啉类荧光化合物的合成及光谱分析

吡唑啉衍生物作为荧光增白剂具有优良的性质,已被广泛应用于染料工业。根据Schellhammer化学结构与荧光性的经验,在吡唑啉环的1-位引入苯并噻唑基,3-位引入吲哚基,5-位引入苯基衍生物,设计并合成了六种新的吡唑啉衍生物,并且通过红外光谱、1H NMR谱、质谱和元素分析进行了确证。化合物的荧光性能测定结果显示此类化合物具有良好的荧光性,均可吸收353 nm左右紫外光,最大发射波长在430～443 nm之间,是一类很有发展前途的蓝紫色荧光化合物。荧光最大发射波长和荧光强度与取代基有关,在苯并噻唑上引入6-Br基团,化合物的荧光发射波长发生蓝移,且强度增大;而引入CH₃基团,化合物的荧光发射波长发生红移,且强度降低。取代基和溶剂极性对荧光量子产率的影响较小。荧光相对强度与荧光量子产率没有直接关系。     

以二苯并吩嗪为核心的聚集诱导发红光材料制备及表征EI北大核心CSCD

有机红光材料在全色显示、生物成像及荧光探针等方面有着重要的应用前景。本文以电子受体二苯并吩嗪为核,在其3,6位引入给电子基二苯胺衍生物,在其11,12位引入拉电子基吡啶,设计并合成了一种具有给-受体结构的化合物DBPAP。通过元素分析、核磁共振波谱和质谱对化合物的化学结构进行了表征与确认。荧光发射光谱表征发现,DBPAP在四氢呋喃和水的混合溶剂中随不良溶剂水含量增加呈现出典型的聚集诱导发光现象。基于其在固态下的有效红光发射,将DBPAP掺杂到PMMA中制备了红光LED器件。在3.8 V工作电压下,器件的最大发射波长为644 nm,CIE坐标为(0.58,0.35),最大亮度为1 616 cd·m^(-2)。该工作为发展新型固态有机红光材料提供了重要思路。     

基于二维相关荧光谱定量分析水中的PAHs

针对水环境中多环芳烃(PAHs)污染现状,提出并建立一种基于二维相关荧光谱水体中PAHs的检测方法。以菲和荧蒽为研究对象,配置36个蒽荧蒽混合水溶液样品(蒽和荧蒽的浓度范围均为1×10-4~1×10~(-6) g·L~(-1)),采集了所有样品的三维荧光光谱。以激发波长为外扰,构建同步二维相关荧光谱。在此基础上建立了定量分析水溶液中蒽和荧蒽浓度的多维偏最小二乘(N-PLS)模型,对蒽和荧蒽的预测均方根误差(RMSEP)分别为5.48×10~(-6) g·L~(-1)和6.25×10~(-6) g·L~(-1)。为了比较,基于常用的三维荧光谱建立了NPLS模型,对蒽和荧蒽的RMSEP分别为5.92×10~(-6) g·L~(-1)和7.33×10~(-6) g·L~(-1)。研究结果表明:基于二维相关荧光谱检测环境中PAHs污染物是可行。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.