原子吸收法测定污泥蚯蚓中的镉、铜、铬、锌、铅

研究用原子吸收法测定蚯蚓中的镉、铜、铬、锌、铅.将制备成粉状的蚯蚓用硝酸-高氯酸消解,在仪器工作条件下,金属离子含量与吸光度呈良好的线性关系.测定结果的相时标准偏差为1.3%～3.5%(n=7),加标回收率为93%～107%.测定镉、铜、铬、锌、铅离子的线性范围、线性相关系数、检出限依次为0～0.9 mg/L,r=0.9984,0.0r7 mg/L;0～10 mg/L,r=0.9989,0.05 mg/L;0～5 mg/L,r=0.999 1,0.13mg/L;0～0.7 mg/L,r=0.9997,0.02 mg/L;0～7.5 mg/L,r=0.9994,0.3 mg/L.     

氢化物发生-原子荧光光谱法测定蔬菜中的镉

研究了以8-羟基喹啉与钴离子作为协同增效剂,氢化物发生-原子荧光光谱测定蔬菜中镉的方法.得到测镉的最佳条件是: 3%HCl 1 mg/L Co2 5 mg/L 8-羟基喹啉体系.本法线性范围0.5～20 μg/L,检出限为0.03 μg/L,RSD为2.5%.本法应用于测定蔬菜中镉的回收率为92%～105%.     

火焰原子吸收法间接测定钢中硼和磷

提出了溶剂萃取-火焰原子吸收光谱法间接测定钢中硼和磷的分析方法.在弱酸性介质中硼酸、苯羟乙酸、铁(Ⅱ)以及邻二氮菲能形成稳定的多元离子缔合物,被1,2-二氯乙烷萃取后再用去离子水反萃取,然后测定水相化合物中的铁;在盐酸介质中,磷酸根与钼酸铵形成磷钼杂多酸,被甲基异丁基甲酮萃取后,测定有机相磷钼杂多酸中的钼.并可分别间接测定硼和磷.在优化的反应条件下,硼和磷的质量浓度分别在0.12～3.24及0.04～1.00mg/L范周内时,吸光度与质量浓度之间具有良好的线性关系,硼和磷的检出限分别为0.036和0.015mg/L.以8份样品空白进行测定,得硼和磷的标准偏差分别为1.2%和0.5%.方法用于钢样中微量硼和磷的测定,拓展了原子吸收分光光度计的应用范围.     

钙、镁、铁、铝离子对土壤中总氟化物检测干扰的消除

建立钙、镁、铁、铝离子对离子选择电极法检测土壤总氟化物干扰的消除方法。通过对含不同浓度水平钙、镁、铁、铝离子的土壤样品中总氟化物进行测试,明确了在总离子强度调节缓冲溶液共存下钙、镁、铁、铝离子对土壤提取液中总氟化物检测结果存在负干扰。通过测试10种土壤样品总氟化物提取液中干扰最强的背景铝含量,对其中土壤提取液中铝离子质量浓度大于10.0 mg/L的3种土壤样品进行加标回收试验,结果表明了土壤总氟化物含量为327～926 mg/kg范围内,当样品提取液中的铝离子含量为50～100 mg/L时,通过减少提取液取样体积为5.00 mL并增加柠檬酸三钠总离子强度缓冲溶液体积至15.0 mL的方法可将加标回收率由56.4%～78.3%优化至94.7%～104.0%;当加入Ca~(2+),Mg~(2+),Fe~(3+)质量浓度为200～300 mg/L,加标回收率由63.1%～77.6%优化为92.4%～105.0%。用优化后的方法测定土壤总氟化物含量为246～2 240 mg/kg的5种标准样品,测试结果与标准值一致。该方法能有效地消除土壤样品总氟化物测定中含钙、镁、铁离子质量浓度为200～300 mg/L,铝离子质量浓度为50～100 mg/L而产生的干扰,具有良好的适用性。     

电感耦合等离子体原子发射光谱法同时测定不锈钢中的11种元素

建立电感耦合等离子体原子发射光谱法同时测定不锈钢中硅、锰、磷、铬、镍、钼、钴、钒、钛、铜、铝11种元素含量的方法。样品采用盐酸溶液溶解,硝酸氧化,在优化的实验条件下,用电感耦合等离子体原子发射光谱法测定各元素含量。磷的质量浓度在0～5 mg/L范围内,钛、铝、钴的质量浓度在0～10 mg/L范围内,钒的质量浓度在0～15mg/L范围内,铜、硅、钼的质量浓度在0～20 mg/L范围内,锰的质量浓度在0～50 mg/L范围内,镍的质量浓度在0～80 mg/L范围内,铬的质量浓度在0～100 mg/L范围内与光谱强度呈良好的线性关系,相关系数均大于0.998,方法检出限为0.002～0.035 mg/L。测定结果的相对标准偏差均小于2%(n=6),加标回收率为97.9%～105.6%.该方法快速、准确,适用于实际生产中不锈钢样品的批量检测。     

固相萃取-气相色谱法测定水中甲胺磷

建立固相萃取-气相色谱法测定水中甲胺磷的方法。以甲醇为洗脱剂,采用椰壳活性炭固相萃取柱对水样富集,将洗脱液氮吹至近干,然后用乙酸乙酯定容至1 mL,采用气相色谱火焰热离子检测器（FTD）检测。甲胺磷的质量浓度在0.1～1.0 mg/L范围内与色谱峰面积线性关系良好,相关系数为0.998,甲胺磷的检出限为0.000 1 mg/L,定量限为0.000 4 mg/L。采用所建方法对实际水样进行测定,地表水和自来水样品加标回收率分别为83.2%～90.8%、87.8%～98.8%,测定结果的相对标准偏差分别为5.5%～8.3%、7.7%～10%(n=6)。该方法操作简单、有机溶剂用量小,可用于生活饮用水及水源水中甲胺磷的测定。     

ICP-AES法测定镍铬铝钇硅合金中的铝、钇、硅

建立电感耦合等离子体发射光谱测定镍铬铝钇硅合金中铝、钇、硅含量的方法。采用盐酸–硝酸(6∶1)混合酸溶解样品,通过基体匹配消除基体镍的干扰,铝、钇、硅的分析谱线分别为394.401,371.029,251.611 nm。铝、钇、硅的质量浓度分别在1.00～30.00,1.00～20.00,1.00～30.00 mg/L范围内与其发射强度呈良好的线性,线性相关系数均大于0.999,检出限分别为0.013,0.002,0.064 mg/L。加标回收率为94.60%～103.51%,测定结果的相对标准偏差均小于2%(n=11)。该方法快速、稳定,可用于实际生产中镍铬铝钇硅中铝、钇、硅元素的测定。     

非水溶剂中微量溶解氧的测定

利用分子氧对联吡啶钌的荧光有淬灭作用的特点,建立了一种灵敏的测定非水体系中微量溶解氧的方法.以甲基三甲氧基硅烷(MTMS)和四乙氧基硅烷(TEOS)为共聚前驱体,以联吡啶钌为荧光指示剂制备了新的有机改性溶胶-凝胶氧敏感膜,并将该膜用于有机体系中溶解氧的测定,响应时间小于30 s.对1,3-丁二醇,丙二醇,丙三醇,PEG-400中溶解氧的测定线性范围分别为0～73.6 mg/L,0～116.4 mg/L,0～205.7 mg/L,0～165.0 mg/L;RSD(n=6)分别为3.5%.5.4%,2.8%和1.0%.该法可用于有机溶剂中溶解氧的测定.     

水中痕量铝离子的浊点萃取-荧光光度法测定

建立了荧光光度法测定水中痕量铝离子的浊点萃取分离富集新体系.在pH 6.0的HAc-NaAc缓冲体系中,水样中的铝与8-羟基喹啉生成疏水性络合物.通过85 ℃水浴加热40 min,8-羟基喹啉-铝络合物被萃取到Triton X-100表面活性剂相并与水相分开.将表面活性剂相用乙醇分散稀释至2.0 mL,在激发波长375 nm和发射波长510 nm下进行荧光测定.测定铝的线性范围为4.0 ～200.0 μg/L,方法的检出限为1.2 μg/L,相对标准偏差(RSD)为4.5%(n=11).方法用于自来水、矿泉水、河水和湖水中痕量铝的测定,加标回收率为92% ～108%.     

中孔分子筛SBA-15-NH2 分离富集火焰原子吸收光谱法测定烟花中痕量钯的研究与应用

建立了中孔分子筛SBA-15-NH2分离富集火焰原子吸收光谱法测定痕量钯的新方法,探讨了中孔分子筛SBA-15-NH2材料吸附钯的原理和最佳条件.在pH 3.0、温度为(15±1) ℃的条件下,钯可被该材料定量吸附,其吸附容量为1.21 mg/g.吸附的钯用饱和硫脲溶液洗脱,并用火焰原子吸收法测定洗脱的钯.该方法测定钯的检出限为0.59 μg/L(3σ,n=11),线性范围为0.002 ～1.2 mg/L,加标回收率为98% ～107%.对0.05 mg/L的Pd2+溶液平行测定7次,RSD为2.24%.方法用于烟花中痕量钯的测定,结果满意.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.