Synthesis and Characterization of Sulfonated Polyimides Containing Trifluoromethyl Groups as Proton Exchange Membranes

A novel sulfonated diamine, 4,4′‐bis(4‐amino‐3‐trifluoromethylphenoxy) biphenyl 3,3′‐disulfonic acid (F‐BAPBDS), was successfully synthesized by nucleophilic aromatic substitution of 4,4′‐dihydroxybiphenyl with 2‐chloro‐5‐nitrobenzotrifluoride, followed by reduction and sulfonation. A series of sulfonated polyimides of high molecular weight (SPI‐x, x represents the molar percentage of the sulfonated monomer) were prepared by copolymerization of 1,4,5,8‐naphathlenetetracarboxylic dianhydride (NTDA) with F‐BAPBDS and nonsulfonated diamine. Flexible and tough membranes of high mechanical strength were obtained by solution casting and the electrolyte properties of the polymers were intensively investigated. The copolymer membranes exhibited excellent oxidative stability due to the introducing of the CF₃ groups. The SPI membranes displayed desirable proton conductivity (0.52×10⁻¹–0.97×10⁻¹ S·cm⁻¹) and low methanol permeability (less than 2.8×10⁻⁷ cm²·s⁻¹). The highest proton conductivity (1.89×10⁻¹ S·cm⁻¹) was obtained for the SPI‐90 membrane at 80°C, with an IEC of 2.12 mequiv/g. This value is higher than that of Nafion 117 (1.7×10⁻¹ S·cm⁻¹). Furthermore, the hydrolytic stability of the obtained SPIs is better than the BDSA and ODADS based SPIs due to the hydrophobic CF₃ groups which protect the imide ring from being attacked by water molecules, in spite of its strong electron‐withdrawing behaviors.     

Synthesis and properties of polyimides from thianthrene-2,3,7,8-tetracarboxylic dianhydride-5,5,10,10-tetraoxide

Thianthrene - 2,3,7,8 - tetracarboxylic dianhydride - 5,5,10,10 - tetraoxide (TADATO), a dianhydride having two sulfonyls between two phenyl rings, was synthesized and polymerized with several diamines by a two-step method. Tough polyimide membranes were obtained with flexible diamines but not with rigid diamines. Most of TADATO-based polyimides are soluble in polar solvents such as N,N-dimethylacetamide and N-methyl-2-pyrrolidone. IR study confirmed that almost complete imidization of TADATO-based poly(amic acid) membranes could be achieved by thermal treatment at 100, 200, and 300°C for each 1 h. In a series of polyimides based on 4,4′-oxydianiline, the polyimide from TADATO showed higher gas permeability coefficient of CO₂ and higher selectivities of CO₂/N₂ and CO₂/CH₄ than those of polyimides from pyromellitic dianhydride and 3,3′,4,4′-biphenyltetracarboxylic dianhydride, and was comparable to that from 2,2-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36 : 485–494, 1998     

Synthesis and properties of novel polyimides from sulfonated binaphthalene dianhydride for proton exchange membranes

A sulfonated dianhydride monomer, 6,6′‐disulfonic‐4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (SBTDA), was successfully synthesized by direct sulfonation of the parent dianhydride, 4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (BTDA), using fuming sulfuric acid as the sulfonating reagent. A series of sulfonated homopolyimides were prepared from SBTDA and various common nonsulfonated diamines. The resulting polymer electrolytes, which contain ion conductivity sites on the deactivated positions of the aryl backbone rings, displayed high proton conductivities of 0.25–0.31 S cm^?1 at 80 °C. The oxidative stability test indicated that the attachment of the ? SO₃H groups onto the dianhydride units did not deteriorate the oxidative stability of the SPI membranes. The better membranes were achieved by the copolymerization of nonsulfonated diamine, SBTDA, and BTDA. Copolymer membrane synthesized from hexane‐1,6‐diamine, SBTDA, and BTDA displayed excellent water stability of more than 1000 h at 90 °C, while its proton conductivity was still at a high level (comparable to that of Nafion 117). Furthermore, the novel block copolymer ( II‐b ) displayed higher proton conductivity compared with the random one ( II‐r ) obviously, probably due to the slightly higher water uptake and better microphase separated morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2820–2832, 2008     

The effect of morphology on sorption and transport of carbon dioxide in a polyimide from 3,3′,4,4′-biphenyltetracarboxylic dianhydride and 4,4′-oxydianiline

Sorption and transport of CO₂ have been investigated for polyimide films prepared from 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and 4,4′-oxydianilline (ODA) as well as for a chemically identical commercial polyimide film, Upilex-R. The BPDA-ODA polyimide films annealed above the glass transition temperature (270°C) are found to have some degree of ordering owing to molecular aggregation of polymer chains, whereas the films as-cast are amorphous. The solubility, permeability, and diffusion coefficients decrease significantly with increasing density or increasing average degree of molecular aggregation. The influence of morphology on the parameters in the dual-mode sorption and transport model has also been investigated. With an increase in density, the Langmuir capacity constant and the diffusion coefficients for Henry's law and Langmuir populations decrease by a larger factor than the Henry's law solubility constant. These results can be tentatively interpreted by assuming either a one-phase or two-phase structure for these polyimide films.     

Synthesis and properties of novel Y‐type nonlinear optical polyimides with high thermal stability of second harmonic generation

2,4‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐1‐(2,2‐dicyanovinyl)benzene dianhydride (4) was prepared and reacted with 4,4′‐oxydianiline, 4,4′‐diaminobenzanilide and 4,4′‐(hexafluoroisopropylidene)dianiline to yield novel Y‐type polyimides 5‐7 containing 2,4‐dioxybenzylidenemalononitrile groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone. The resulting polyimides 5‐7 are soluble in polar solvents such as dimethylsulfoxide and N,N‐dimethylformamide. Polymers 5‐7 showed a thermal stability up to 330 °C in thermogravimetric analysis thermograms with T_g values obtained from differential scanning calorimetry thermograms in the range 179–194 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064 nm fundamental wavelength were around 5.56 × 10^?9 esu. The dipole alignment exhibited exceptionally high thermal stability even at 20 °C higher than the glass‐transition temperature there was no SHG decay below 215 °C because of the partial main‐chain character of polymer structure, which is acceptable for NLO device applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3078–3087, 2008     

Synthesis and properties of novel sulfonated (co)polyimides bearing sulfonated aromatic pendant groups for PEFC applications

Novel sulfonated diamines bearing aromatic pendant groups, namely, 3,5‐diamino‐3′‐sulfo‐4′‐(4‐sulfophenoxy) benzophenone (DASSPB) and 3,5‐diamino‐3′‐sulfo‐4′‐(2,4‐disulfophenoxy) benzophenone (DASDSPB), were successfully synthesized. Novel side‐chain‐type sulfonated (co)polyimides (SPIs) were synthesized from these two diamines, 1,4,5,8‐naphthalene tetracarboxylic dianhydride (NTDA) and nonsulfonated diamines such as 4,4′‐bis(3‐aminophenoxy) phenyl sulfone (BAPPS). Tough and transparent membranes of SPIs with ion exchange capacity of 1.5–2.9 meq g^?1 were prepared. They showed good solubility and high thermal stability up to 300 °C. They showed isotropic membrane swelling in water, which was different from the main‐chain‐type and sulfoalkoxy‐based side‐chain‐type SPIs. The relative humidity (RH) and temperature dependence of proton conductivity were examined. At low RH, the novel SPI membranes showed much higher conductivity than the sulfoalkoxy‐based SPIs. They showed comparable or even higher proton conductivity than Nafion 112 in water at 60 °C (>0.10 S cm^?1). The membrane of NTDA‐DASDSPB/BAPPS (1/1)‐s displayed reasonably high proton conductivities of 0.05 and 0.30 S cm^?1 at 50 and 100% RH, respectively, at 120 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2862–2872, 2006     

Separation of carbon dioxide from nitrogen using ion-exchanged faujasite-type zeolite membranes formed on porous support tubes

Faujasite-type zeolite membranes were reproducibly synthesized by hydrothermal reaction on the outer surface of a porous α-alumina support tube of 30 or 200 mm in length. The membrane properties were evaluated by CO₂ separation from an equimolar mixture of CO₂ and N₂ at a permeation temperature of 40°C. CO₂ permeance and CO₂/N₂ selectivity of the NaY-type membranes were in the ranges of 0.4×10⁻⁶–2.5×10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹ and 20–50, respectively. The NaY-type membranes were ion-exchanged with alkali and alkaline earth cations. The LiY-type membrane showed the highest N₂ permeance and the lowest CO₂/N₂ selectivity. The KY-type membrane gave the highest CO₂/N₂ selectivity. The NaY-type membrane was stable against exposure to air at 400°C. NaX-type zeolite membranes, formed by decreasing the ratio of SiO₂/Al₂O₃ in the starting solution, exhibited lower CO₂ permeances and higher CO₂/N₂ selectivities than those of the NaY-type zeolite membranes.     

Polyimide–Silica Gel Hybrids Containing Metal Salts: Preparation via the Sol–Gel Reaction

A facile preparation of polyimide–silica gel hybrids by the simultaneous in-situ formation of polyimides during the hydrolysis–condensation of tetramethoxysilane (TMOS) is reported here. The hydrolysis and condensation of TMOS was carried out in a solution of DMAc containing 5% LiCl, CaCl₂ or ZnCl₂ and the seven-membered cyclic polyimide intermediate. The seven-membered cyclic intermediates, precursors of polyimides, were derived from the low-temperature polycondensation of dianhydrides [benzophenonetetracarboxylic dianhydride (BTDA), pyromellitic dianhydride (PMDA), and 4,4-bis(hexafluoroisopropylidene)phthalic dianhydride (6FDA)] and di-isocyanates [isophorone di-isocyanate (IPDI), toluene di-isocyanate (TDI), hexamethylene di-isocyanate (HDI) and 4,4′-diphenylmethane di-isocyanate (MDI)]. These intermediates could readily be converted to the corresponding polyimides. Films were cast from the resulting mixtures and the solvent was gradually evaporated at 130 °C to result in the formation of clear, transparent, pale yellow or amber-colored hybrid films in which the salts were dispersed at the molecular level. Pyrolysis of polyimide–silica gel hybrids at 600 °C gave mesoporous silica. Silica gel obtained from hybrids HPI-8 (containing no salt) and HPI-11 (containing ZnCl₂) had a pore radius (BJH method) of 2.9 nm, while that from hybrid HPI-9 (containing LiCl) had a pore radius of 11.4 nm. The surface areas (BET method) obtained were 203 m² g⁻¹, 19 m² g⁻¹ and 285 m² g⁻¹, while the pore volumes were 0.373 cm³ g⁻¹, 0.158 cm³ g⁻¹ and 0.387 cm³ g⁻¹, respectively, for samples obtained from hybrids HPI-8, HPI-9 and HPI-11. © 1997 by John Wiley & Sons, Ltd.     

Scalings of fluorine‐containing polyimides in cyclopentanone

Eight 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropane dianhydride‐4,4′‐diamino‐3,3′‐dimethylbiphenyl (6FDA‐OTOL) fractions and seven 2,2′‐bis[4‐(3,4‐dicarboxyphenoxy) phenyl] propane dianhydride‐4,4′‐diamino‐3,3′‐dimethylbiphenyl (BISADA‐OTOL) fractions in cyclopentanone at 30 °C were characterized by a combination of viscometry and static and dynamic laser light scattering (LLS). In static LLS, the angular dependence of the absolute scattered intensity led to the weight‐average molar mass (M_w), the z‐average root mean square radius of gyration, and the second virial coefficient. In dynamic LLS, the Laplace inversion of each measured intensity–intensity time correlation function resulted in a corresponding translational diffusion coefficient distribution [G(D)]. The scalings of 〈D〉 (cm²/s) = 8.13 × 10⁻⁵ M_w^−0.47 and [η] (dL/g) = 2.36 × 10⁻³ M_w^0.54 for 6FDA‐OTOL and 〈D〉 (cm²/s) = 3.02 × 10⁻⁴ M_w^−0.60 and [η] (dL/g) = 2.32 × 10⁻³ M_w^0.53 for BISADA‐OTOL were established. With these scalings, we successfully converted each G(D) value into a corresponding molar mass distribution. At 30 °C, cyclopentanone is a good solvent for BISADA‐OTOL but a poor solvent for 6FDA‐OTOL; this can be attributed to an ether linkage in BISADA‐OTOL. Therefore, BISADA‐OTOL has a more extended chain conformation than 6FDA‐OTOL in cyclopentanone. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2077–2080, 2000     

Effect of polyethyleneglycol (PEG) on gas permeabilities and permselectivities in its cellulose acetate (CA) blend membranes

The effect of polyethyleneglycol (PEG) on gas permeabilities and selectivities was investigated in a series of miscible cellulose acetate (CA) blend membranes. The permeabilities of CO₂, H₂, O₂, CH₄, N₂ were measured at temperatures from 30 to 80°C and pressures from 20 to 76 cmHg using a manometric permeation apparatus. It was determined that the blend membrane having 10 wt% PEG20000 exhibited higher permeability for CO₂ and higher permselectivity for CO₂ over N₂ and CH₄ than those of the membranes which contained 10% PEG of the molecular weight in the range 200–6000. The CA blend containing 60 wt% PEG20000 showed that its permeability coefficients of CO₂ and ideal separation factors for CO₂ over N₂ reached above 2 × 10⁻⁸ [cm³ (STP) cm/cm² s cmHg] and 22, respectively, at 70°C and 20 cmHg. Based on the data of gas permeability coefficients, time lags and characterization of the membranes, it is proposed that the apparent solubility coefficients of all CA and PEG blend membranes for CO₂ were lower than those of the CA membrane. However, almost all the blend membranes containing PEG20000 showed higher apparent diffusivity coefficients for CO₂, resulting in higher permeability coefficients of CO₂ with relation to those of the CA membrane. It is attributed to the high diffusivity selectivities of CA and PEG20000 blend membranes that their ideal separation factors for CO₂ over N₂ were higher than those of the CA membrane in the range 50–80°C, even though the ideal separation factors of almost all PEG blend membranes for CO₂ over CH₄ became lower than those of the CA membrane over nearly the full range from 30° to 80°C.     

Fully imidized soluble polyimides based on a novel dianhydride: 2,2′-dichloro-4,4′,5,5′-benzophenone tetracarboxylic dianhydride

We have synthesized a novel dianhydride, 2,2′-dichloro-4,4′,5,5′-benzophenone tetracarboxylic dianhydride (DCBTDA). Polyimides were synthesized with DCBTDA or 3,3′,4,4′-benzophenone tetracarboxylic dianhydride (BTDA) and several relatively rigid meta- and para- substituted mononuclear diamines. The BTDA based systems were insoluble in dipolar, aprotic solvents whereas the DCBTDA based polymers displayed enhanced solubility in these solvents. The thermal stability of these polyimides was excellent as measured by 5% weight loss decomposition. The T_g's of the polymers were all above 290°C.     

Preparation of Poly(amic acid) and Polyimide via Microwave-Assisted Polycondensation of Aromatic Dianhydrides and Diamines

Summary: A copolycondesation-type poly (amic acid) (PAA) was synthesized using pyromellitic dianhydride (PMDA) and 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) as dianhydride monomers, and 4,4′-oxydianiline (ODA) as a diamine monomer under microwave irradiation in dimethylformamide (DMF). PAA was then converted into a polyimide (PI) by an imidization. The structure and performance of the polymer were characterized by Fourier-transform infrared (FT-IR) spectroscopy, Proton nuclear magnetic resonance (¹H NMR) spectrometry, viscosity, X-ray diffraction (XRD), and thermogravimetric (TG) analyses. The results showed that under microwave irradiation, the intrinsic viscosity and the yield of PAA were increases, and the reaction time was shortened. The FT-IR spectra of the polymer revealed characteristic peaks for PI around 1778^– and 1723 cm^–1. TG curves indicated that the obtained PI began to lose weight at 535 °C, and its 10% thermal decomposition temperature under N₂ was 587 °C.     

Gas separation properties of ultra-thin films based on fully cyclized polyimides

Fully cyclized polyimides based on octadecyl- or hexadecyl 3,5-diaminobenzoate and 4,4′-(hexafluoroisopropylidene)diphthalic anhydride or 4,4′-oxydiphthalic anhydride were synthesized and deposited by the Langmuir-Schaefer technique onto a poly(1-trimethylsilylprop-1-yne) support. Composite membranes thus prepared show selective gas permeation for N₂, O₂, CO₂, H₂ with permeation rates in the range of 10⁻⁵ to 10⁻⁷ cm³ (STP)/(cm² · s · cmHg).     

Dual activity of electrocatalytic activated CO2 toward pyridine for synthesis of isonicotinic acid: An EC′C′C mechanism

The present study demonstrates the indirect electrocatalytic synthesis of isonicotinic acid using a Ni complex, [Ni^II(Me₄-(NO₂Bzo)₂[14]tetraeneN₄)], in an acetonitrile solution at room temperature. The complex was used as an excellent electrocatalyst for the reduction of carbon dioxide. The results indicate that the electrocatalytic reduction product of CO₂ (CO₂⁻) has a dual role in the electrosynthesis of isonicotinic acid. The dual activity of CO₂⁻ involved indirect electrocatalytic reduction of pyridine as well as its radical reaction with pyridine radical anion to form isonicotinic acid. Finally, EC′C′C mechanism was proposed for the synthesis of isonicotinic acid. In contrast, the reaction of pyridine with CO₂ in the absence of the complex follows an EC′C mechanism, and the final product is 4,4′-bipyridine.     

Preparation and Pervaporation Performances of PEA‐based Polyurethaneurea and Polyurethaneimide Membranes to Benzene/Cyclohexane Mixture

Pervaporation is promising in the separation of benzene/cyclohexane mixture for the petrochemical industry. Two kinds of pervaporation membrane materials, including PEA‐based polyurethaneurea (PUU) and polyurethaneimide (PUI), were successfully synthesized from the same soft segment of poly(ethylene adipate)diol (PEA) and different hard segments via a two‐step method. The hard segment of PUU was prepared from toluene diisocyanate (TDI) and 4,4′‐diaminodiphenyl methane (MDA), while that of PUI was from 4,4′‐methylene‐bis(phenylisocyanate) (MDI) and pyromellitic dianhydride (PMDA). The structures and properties of PUU and PUI were characterized by means of FT‐IR, DSC and TGA. During the pervaporation experiment, the PUI membranes had a flux of 12.13 kg µm m^?2 h^?1 and separation factor of 8.25, while the PUU membranes had a flux of 26.35 kg µm m^?2 h^?1 and separation factor of 6.29 for 50 wt% benzene in the benzene/cyclohexane mixture at 40°C. The effects of the structures of hard segments on pervaporation performances were discussed. The investigation of the relationship in molecular structure and PV performances will be helpful for the choice and design of membrane materials in the separation of benzene/cyclohexane mixture.     

Characterization of cobalt-modified polyimides

Modified polyimide films containing cobalt have been prepared by the addition of cobalt(II) chloride to a solution containing one of the diamines 4,4′-oxydianiline (ODA) or 4,4′-diaminodiphenylsulfide (DDS) and one of the dianhydrides 3.3′, 4,4′-benzophenonetetracarboxylic dianhydride (BTDA) or 4,4′-bis(3,4-dicarboxyphenoxy)diphenylsulfide dianhydride (BDSDA) and characterized by thermal methods, UV-visible spectra, room-temperature direct-current electrical resistivity measurements, and X-ray photoelectron and Auger electron spectroscopy. A principal goal of this work was to establish if there was coordination of the potential donor atoms of the polymide to cobalt. UV-visible spectra of the modified polyamic acid solutions and polyimide films and a titration study of a model system do not show any appreciable coordination with either the polyamic acid or the polyimide; rather, the cobalt(II) appears to be coordinated to the solvent, N,N-dimethylacetamide (DMAc), as [Co(DMAc)₄]²⁺, until the temperature is raised above 200°C. X-ray photoelectron spectra of films cured only to 200°C also do not show significant shifts in the binding energies of the potential donor atoms from those binding energies of the undoped polymers, confirming little direct coordination of the cobalt to atoms of the polyimide. Heating the films to 300°C in a forced-air oven causes the formation of a cobalt oxide layer on the air side of the polymer. Direct-current electrical resistivity measurements on this surface show a 10⁴–10⁶ reduction in resistivity due to this layer.     

Thermal treatment of dense polyimide membranes

A study has been conducted to clarify the relationship between polymer structure, annealing temperature, and the extent of plasticization by high‐pressure CO₂ for two typical polyimide membranes; BTDA‐DAPI (poly(3,3′‐4,4′‐benzophenone tetracarboxylic–dianhydride diaminophenylindane) and 6FDA‐TMPDA (poly(2,2′‐bis(3,4′‐dicasrboxyphenyl) hexafluoropropane dianhydride–2,3,5,6‐tetramethyl‐1,4‐phenylenediamine). Both membrane materials are exposed to varying levels of thermal annealing at 200 and 250 °C. The effect of this heat treatment on free volume is examined using positron annihilation lifetime spectroscopy (PALS), whereas fluorescence spectroscopy is used to monitor changes in electronic structure. Results show that thermal annealing causes a reduction in both the size and number of free volume elements. A strong relationship is found between the fluorescence peak intensity for 6FDA‐TMPDA and both the membrane gas permeability and plasticization pressure. This correlation is most likely the result of the formation of charge transfer complexes, particularly at 250 °C. However, the formation of covalent crosslinks at these temperatures cannot be discounted. No fluorescence is observed for BTDI‐DAPI. Although thermal annealing has a significant effect on the extent of plasticization in both polymers, it is found that the rate of plasticization is unaffected by the annealing temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1879–1890, 2008     

Enhancement on the permeation performance of polyimide mixed matrix membranes by incorporation of graphene oxide with different oxidation degrees

Graphene oxide (GO) with different oxidation degrees were synthesized by harsh oxidation of graphite using the improved Hummers method. The GO/polyimide (PI) mixed matrix membrane was successfully fabricated by in situ polymerization of PI monomers (3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 4,4′‐diaminodiphenyl ether) with GO. The structure of GO was characterized by Fourier transform infrared, transmission electron microscopy, atomic force microscopy, X‐ray diffraction, and thermal gravimetric analysis–differential thermal analysis. The performance of different GO/PI mixed matrix membranes was evaluated by permeation experiments of CO₂/N₂ gas mixture (volume ratio, 1:9). Results showed that more polar functional groups were introduced to GO with the increase in oxidation degree of GO in the preparation process, producing fewer layers and more translucent structures. GO with higher oxidation degree has significant effect on its dispersion in the N,N‐dimethylacetamide solvent and polymer matrix materials. The permeability of GO/PI hybrid membranes for CO₂ and N₂ increased. The CO₂/N₂ permeation selectivity of membranes exhibited a trend of initial increase, followed by a decrease, with the increase in oxidation degree, when the same amount of GO was added. For GO with the same oxidation degree, the permeability and permeation selectivity of hybrid membrane initially increased, and then decreased with the addition content of GO. In the case of hybrid membrane containing 1 wt% monolayer GO, the maximum permeability and permeation selectivity of hybrid membranes for CO₂ were 14.3 and 4.2 times more than that of PI membrane without GO, respectively. Copyright © 2015 John Wiley & Sons, Ltd.     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Syntheses and properties of organosoluble polyimides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4, 7‐methanohexahydroindan

A series of organosoluble aromatic polyimides (PIs) was synthesized from 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4,7‐methanohexahydroindan (3) and commercial available aromatic dianhydrides such as 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA), 4,4′‐sulfonyl diphthalic anhydride (SDPA), or 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropanic dianhydride (6FDA). PIs (III_c–f), which were synthesized by direct polymerization in m‐cresol, had inherent viscosities of 0.83–1.05 dL/g. These polymers could easily be dissolved in N,N′‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), N,N‐dimethylformamide (DMF), pyridine, m‐cresol, and dichloromethane. Whereas copolymerization was proceeded with equivalent molar ratios of pyromellitic dianhydride (PMDA)/6FDA, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA)/6FDA, or BTDA/SDPA, or ½ for PMDA/SDPA, copolyimides (co‐PIs), derived from 3 and mixed dianhydrides, were soluble in NMP. All the soluble PIs could form transparent, flexible, and tough films, and they showed amorphous characteristics. These films had tensile strengths of 88–111 MPa, elongations at break of 5–10% and initial moduli of 2.01–2.67 GPa. The glass transition temperatures of these polymers were in the range of 252–311°C. Except for III_e, the 10% weight loss temperatures (T_d) of PIs were above 500°C, and the amount of carbonized residues of the PIs at 800°C in nitrogen atmosphere were above 50%. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1681–1691, 1999