Ion implantation effects in glasses

Abstract

Ion implantation can be used to introduce network damage and to alter the chemical composition in glasses. Structural changes can be inferred from IR measurements near 1000 cm^?1 and by optical absorption near 2150 Å. Implantation-induced damage decreases the implanted volume in fused silica with consequent changes in the refractive index, the near-surface hardness, and the tensile surface stress. Prior work in these areas is reviewed. Implantation into alkali silicate glasses depletes the alkali content in the implanted region. These changes allow preferential surface crystallization in Li₂O-2SiO₂ glasses. Crystallization of amorphous SiO2 can be induced by implantation of Li. Insight into the crystallization process is obtained by following the associated ion movement by elastic recoil detection (ERD) and optical techniques. Implantation of 20keV H shows that saturation of implanted H-sites in fused silica occurs at about 2.2 × 10²¹ H/cm³ in agreement with free volume estimates of the maximum number of available interstitial sites. Details of H and D interactions in fused silica were studied as a function of fluence and temperature. Results are of interest in studies of corrosion in glasses considered for nuclear waste encapsulation and for components in fusion reactors.

IV Summary     

Collisional Energy Transfer of Highly Vibrationally Excited Polyatomic Molecules. The Effect of Excited Molecule Complexity

Collisional relaxation was probed by CO₂ laser activated delayed fluorescence. The experimental information was adopted to determine the average energies transferred per collision (ΔE) from highly vibrationally excited polyatomic molecules to parent collider. The values of (ΔE) decreased with increasing the number of atoms in the excited molecules in line: biacetyl, acetophenone, benzophenone, antraquinone. The dependences of (ΔE) on the number of factors such as: 1) the average vibrational energy residing in the vibrational modes of excited molecules; 2) the potential of intermolecular interaction; 3) the reduced mass, and others were analyzed in details. The general interplay was noticed between (ΔE) and the molecular parameters which determined the increasing interaction strength and the decreasing energy transfer efficiency due to the adiabatic constraints on the energy transfer.     

Sequence and Hot Transitions in the Co2 Molecule; Interference of Adjacent Lines Belonging to Different Transitions as a Function of Temperature

Carbon-dioxide spectra of some higher transitions in the 9-11μm region were studied. Spectra of the sequence ([10°1,02°1]_I,II - 00°2) and hot (01¹1 - 11¹0) bands were calculated as a function of temperature. the positions of the ro-vibrational transitions and their intensities were determined as a function of temperature. for lines in hot and sequence transitions whose positions are close to some of the regular lines ([l0⁰0,02⁰0]_I,II - 00°1)¹ absorption coefficients of adjacent lines were calculated as functions of line center distances and temperature. the resulting values of the absorption coefficient for conditions of constant pressure or constant volume were determined.     

Effect of phase transformation on optical and dielectric properties of zirconium oxide nanoparticles

Zirconium oxide nanoparticle (ZrO₂) is synthesized by the hydrothermal method at different calcination temperatures. The structural analysis is carried out by X-ray diffraction and Raman spectra. The sample prepared at 400 °C and 1100 °C showed the cubic and monoclinic phase, respectively, and the sample calcined at 600 °C and 800 °C showed the mixed phase with co-existence of cubic and monoclinic phases. Furthermore, the morphology and particle size of these samples were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. The band gap estimated from UV–Vis spectra of ZrO₂ (zirconia) nanocrystalline materials calcined at different temperatures from 400 °C to 1100 °C was in the range of 2.6–4.2 eV. The frequency dependence of dielectric constant and dielectric loss was investigated at room temperature. The low frequency region of dielectric constant is attributed to space charge effects.     

Diffusion Kinetics of Vitamin B12 from Alginate and Poly(vinyl acetate) Based Gel Scaffolds for Targeted Drug Delivery

Abstract

The research described here probed the thermodynamics and kinetics of Vitamin B₁₂ release from two types of polymeric gel scaffolds for targeted drug delivery applications. The polymeric gel scaffolds were successfully prepared from sodium alginate and polyvinyl acetate (PVA) using crosslinking and casting mechanisms, respectively. Vitamin B₁₂ was effectively blended into the polymeric gel scaffolds during their synthesis processes. The release of Vitamin B₁₂ from the polymeric gel scaffolds was characterized by immersing the scaffolds in a brine solution at various temperatures (25?°C, 32?°C and 37?°C) and, simultaneously, the transient concentrations were measured using a UV visible spectrophotometer. The sodium alginate gel scaffolds exhibited a more rapid release of Vitamin B₁₂ as compared to the PVA gel scaffolds. The Vitamin B₁₂ release kinetics from the alginate and PVA scaffolds were characterized by fitting the experimental data with various diffusion kinetic models. The Vitamin B₁₂ release from the alginate gel scaffolds followed the Peppas-Sahlin model, whereas releases from the PVA gel scaffolds were fitted to the Hopfenberg model. The diffusion coefficients for the alginate scaffolds with respect to the three temperatures were found to be 15.72?m²/s, 17.17?m²/s and 18.58?m²/s respectively whereas the diffusion coefficients for the PVA scaffolds with respect to the three temperatures were found to be 0.23?m²/s, 0.29?m²/s and 0.32?m²/s respectively. The activation energies (E_a) for the two types of polymeric scaffolds were calculated using the Stannett equation and found to be 10.38?kJ.mol^?1 and 20.47?kJ.mol^?1 for the alginate and PVA scaffolds, respectively, for all three temperatures.     

Laser desorption of NO from a thick C60 film

The desorption of NO molecules from a thick C₆₀ film is reported. A thermal desorption spectrum indicates two adsorption sites with binding energies of E_b = 0.30 eV and 0.55 eV. For laser desorption the fullerene surface is exposed to NO and excited by 7 ns UV laser pulses. Desorbing NO molecules are recorded state selectively as well as time resolved. The time-of-flight measurement indicates three different desorption pathways. A fast channel shows rovibronic temperatures of T_rot(v″ = 0) = 370 K, T_rot(v″ = 1) = 390 K and T_vib = 610 K as well as strong rotational-translational coupling. The desorption yield for the fast channel increases linearly with pulse energy with a desorption cross section of σ = (5.1 ± 0.9) × 10⁻¹⁷ cm². Dominating the signal for small J″ values is a slow channel with low rotational and translational temperatures of about 110 K. We assign this peak to a laser-induced thermal desorption. For large pump-probe delays the data deviate from the Maxwellian flux distribution and a third channel appears with extremely late arrival times.     

Thermally stimulated luminescence from alkaline earth borates

The thermally stimulated luminescence from XB₂O₄ (X=Ca,Sr,Ba) has been investigated. The results on CaB₂O₄ and SrB₂O₄ are being reported here for the first time. In both cases, the emission is found to be quite intense, contrary to the case with BaB₂O₄. The presence of two peaks in the glow curves is noted over the temperature range of 300-570 K. The emission spectra corresponding to both the peaks have been observed to be identical, consisting of two broad emissions, one in the UV and other in the blue-green regions. The emission is apparently quite different from that of BaB₂O₄ in which case only very weak emission spreading over a broad wavelength range around 410 nm is observed. This result has been understood in terms of the overlap between the excitation and the emission spectra.     

MgH2(110)表面Pd单原子催化氢脱附反应的第一性原理研究

本文采用第一性原理密度泛函理论计算研究了MgH₂(110)表面吸附单原子Pd后的氢脱附反应. 计算发现,在吸附一个Pd单原子后,MgH₂(110)表面氢脱附反应的能垒可以从1.802 eV显著地降低到1.154 eV,表明Pd单原子对于氢脱附具有很强的催化效应. 并且,Pd单原子催化还可以将氢脱附的温度从573 K显著地降低到了367 K,从而使MgH₂(110)表面的氢脱附反应更加容易和快速地发生. 此外,通过MgH₂(110)表面氢溢出机制的反向过程来讨论了氢脱附反应的微观过程. 该研究表明Pd/MgH₂薄膜在未来的实验中可作为良好的储氢材料.     

异丙醇在锐钛矿TiO2(101)表面的光化学

通过程序升温脱附谱的方法探究了266 nm激光照射下异丙醇在锐钛矿TiO₂（101）表面的光化学,并提出了详细的解离机理.在光照作用下,异丙醇发生分步解离：首先,O-H键断裂生成异丙氧基;然后,仲碳的C-H键在光照的作用下进一步发生解离,从而生成丙酮,两步生成的氢原子均转移到相邻的桥氧上.在升温过程中,这部分氢原子会与分子态的异丙醇发生置换反应,从而以低温水和高温异丙基的形式从表面脱附出来.     

Effect of aluminum on the morphological and textural properties of CuO-ZnO/H-Ferrierite

Hybrid catalysts containing CuO-ZnO or CuO-ZnO-Al₂O₃ as the metallic component and the zeolite H-ferrierite as support were prepared by both the coprecipitation-impregnation and coprecipitation-sedimentation methods. They were characterized by XRD, BET, and TEM. Aluminum was added to the metallic component, and the effects on the hybrid catalyst properties were studied. The metallic component blocked the zeolite micropore volume, and spaces were created between agglomerate particles of the first component, increasing mesopore volume. Aluminum introduction at a Cu/Zn/Al ratio of 55/30/15 favored the formation of hydrotalcite as a precursor to CuO/ZnO/Al₂O₃. In this case, small, highly dispersed particles of these oxides were obtained. In the coprecipitation-impregnation method, greater contact between the H-ferrierite zeolite and the metallic component was observed.     

CO2 laser assisted removal of UO2 and ThO2 particulates from metal surface

Pulsed laser assisted removal of uranium dioxide and thorium dioxide particulates from stainless steel surface have been studied using a TEA CO₂ laser. Decontamination efficiency is measured as a function of laser fluence and number of pulses. Threshold fluence for the removal of UO₂ particulates has been found to be lower than that required for the removal ThO₂ particulates. Usage of a ZnSe substrate, that is transparent to the laser wavelength used here, enabled us to decouple the cleaning effect arising out of absorption in the particulates from that in the substrate and has contributed towards understanding the mechanism responsible for cleaning. The experimental observations are also corroborated by simple theoretical calculations.     

Effect of hydrogen-doping on bonding properties of Ti3SiC2

Using the first principles method based on the density functional theory, we investigated the effect of hydrogen-doping on bonding properties of Ti₃SiC₂. The formation energies of hydrogen interstitials in three possible positions were calculated. The results show that hydrogen favors residing near the (0 0 1) Si plane. In these positions, hydrogen is hybridized most with 1s states of lattice atoms (Si and C), instead of Ti. The presence of hydrogen does not substantially influence the bonding nature of Ti₃SiC₂; chemical bonding is characterized by the hybridizations of Ti d-Si p and Ti d-C p states, and yields high strength. This is contrary to hydrogen-doping in transition metals, where the electron of hydrogen fills in the d bands of the metals and, as a consequence, decreases the cohesive strength of the lattice.     

A theoretical study on the kinetics of multichannel Multiwell reaction of H2S(1A1) with HO2(2A′′)

The mechanism and kinetics of the reaction of hydrogen sulphide (H₂S(¹A₁)) with hydroperoxyl radical (HO₂(²A″)) on the lowest doublet potential energy surface have been theoretically studied. The potential energy surface for possible pathways has been investigated by employing Complete Basis Set (CBS), DFT, and CCSD(T) methods. Three possible pathways are suggested for the title reaction. The most probable entrance channel consists of formation of a hydrogen-bonded pre-reaction complex (vdw1) and two energised intermediates. Multichannel RRKM-Steady State Approximation and CVT calculations have been carried out to compute the rate constants over a broad range of temperature from 200?K to 3000?K to cover the atmospheric and combustion conditions and pressure from 0.1 to 2000?Torr. No sign of pressure dependence was observed for the title reaction over the stated range of pressure. We have shown that the major products of the title reaction are H₂O₂ and SH while at higher temperatures, formation of the other products such as H₂O, HOS, HSOH and OH are feasible, too. Our calculated overall rate constant is in agreement with the reported experimental data in the literature.     

Investigation of tetragonal ReN2 and WN2 with high shear moduli from first-principles calculations

Two new transition metal dinitrides, ReN₂ and WN₂, with the P4/mmm structure are investigated by the first-principles calculations. The computed shear moduli of 327 GPa for ReN₂ and 334 GPa for WN₂ exceed those of all transition metal dinitrides previously reported. The estimated theoretical hardness are 46.3 GPa for ReN₂ and 47.9 GPa for WN₂, respectively. The calculated high shear moduli and hardness indicate that they are potential ultrahard materials. It is important to note that the computed hardness of the weakest bond are 34.7 GPa (W-N) for WN₂ and 33.1 GPa (Re-N) for ReN₂, much higher than that of 21.1 GPa (Re-B) for ReB₂, which suggests that tetragonal ReN₂ and WN₂ are probably harder than ReB₂. The total and partial electron density of states and the electron localization function for ReN₂ and WN₂ are analyzed. We attribute the high bulk modulus, shear modulus, and hardness to a three-dimensional covalently bonded framework in tetragonal ReN₂ and WN₂. Our calculations show that tetragonal ReN₂ is expected to be synthesized above 62.7 GPa and tetragonal WN₂ may be hard to be synthesized.     

Electronic Emission from Hg-Atoms and HgCl-Radicals Due to Collisions of Nitrogen Ions and HgCl2/Hg2Cl2 Molecules

Emission spectra of the (B-X), (C-X) and (D-X) band systems of HgCl-radical and mercury atomic lines from highly excited levels to various lower levels have been observed during collisions of N⁺ and N⁺ ₂ ions and HgCl₂/Hg₂Cl₂ molecules at different laboratory kinetic energies of the projectile ions. Emission cross-sections of the most intense mercury atomic lines and the (C-X) band system of the HgCl-radicals, have been measured in the laboratory kinetic energy range of 100–900 eV.     

A Sensitive Isotope Selective Nondispersive Infrared Spectrometer for 13CO2 and 12CO2 Concentration Measurements in Breath Samples

We present a nondispersive infrared spectrometer (NDIRS) for the measurement of the ¹³CO₂/¹²CO₂-ratio in breath samples. A commercial NDIR spectrometer for CO₂ concentration measurements in industrial process control was modified using two separate optical channels for the ¹³CO₂ and ¹²CO₂ detection. Cross interference due to overlapping absorption lines of both isotopic gases was successfully eliminated. The sensitivity of this device is ± 0.4‰ of the ¹³CO₂/¹²CO₂-ratio in a range of 2.5 to 5% of total CO₂. This is sufficient for biomedical applications. Our spectrometer is small in size, cheap and simple to operate and thus a true alternative to isotope ratio mass spectrometers (IRMS). Several biomedical applications with breath samples were demonstrated and were compared in very good agreement with IRMS.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Low-temperature deposition of stoichiometric HfO2 on silicon: Analysis and quantification of the HfO2/Si interface from electrical and XPS measurements

An understanding of the exact structural makeup of dielectric interface is crucial for development of novel gate materials. In this paper a study of the HfO₂/Si interface created by the low-temperature deposition ultrathin stoichiometric HfO₂ on Si substrates by reactive sputtering is presented. Analysis, quantification and calculation of layer thickness of an HfO₂/Hf-Si-O_x/SiO₂ gate stack dielectrics have been performed, using X-ray photoelectron spectroscopy (XPS) depth profile method, angle resolved XPS and interface modeling by XPS data processing software. The results obtained were found to be in good agreement with the high frequency capacitance-voltage (C-V) measurements. The results suggest a development of a complex three layer dielectric stack, including hafnium dioxide layer, a narrow interface of hafnium silicate and broad region of oxygen diffusion into silicon wafer. The diffusion of oxygen was found particularly detrimental to the electrical properties of the stack, as this oxygen concentration gradient leads to the formation of suboxides of silicon with a lower permittivity, κ.     

The Matrix Isolation Spectrum of the CH2 Ion

For CH₂⁺ molecular ions at 5 K we simulate the infrared absorption spectrum, and tabulate all strong absorption lines from 0 to 16 000 cm⁻¹. We use ab initio potential energy, dipole moment, and transition moment surfaces in conjunction with our program system RENNER, which allows for the Renner-Teller effect and spin-orbit coupling in a full-dimensions calculation. This is done for the purpose of guiding our search for the matrix isolation spectrum; our attempts at finding this spectrum are also described.