Kinetics and Equilibria of Synthesized Anionic Surfactant onto Berea Sandstone

We present static adsorption studies of anionic surfactants on crushed Berea sandstone. The maximum adsorption density was 0.9604 mg/g. The kinetics of adsorption process was modeled using pseudo-first-order and pseudo-second-order rate equations at 25°C and 70°C. The equilibrium adsorption process was validated using Langmuir and Freundlich adsorption models. In addition, the effects of different parameters that govern the effectiveness of these surfactants such as pH and temperature were also investigated. The kinetic study results show that the surfactant adsorption is a time dependent process. The apparent rate constant of adsorption process determined by the first-order kinetic model at 25°C and 70°C were 0.11768 and ?0.04513, respectively. The rate constant for pseudo-second-order kinetic model was 0.0086 at 25°C and 0.0101 at 70°C. The adsorption of anionic surfactant followed pseudo-second-order kinetic model. The Freundlich and Langmuir model constant were 1.6509 × 10^?4 and ?9.775 × 10^?5, respectively. The equilibrium results showed that the adsorption of anionic surfactant onto Berea sandstone was well described by Langmuir adsorption model. It was concluded that anionic surfactants performed better at higher pH and temperature.      

Preparation the Esters of Oleic Acid-Maleic Anhydride Copolymer and Their Evaluation as Flow Improvers for Waxy Crude Oil

Five comb-like copolymers derived from oleic acid-maleic anhydride were prepared and then esterified by long-chain fatty alcohol (POMA C_n), where n = 18, 20, 22. These polymers were characterized by FTIR and ¹H NMR analysis. The molecular weight was determined by using gel permeation chromatography (GPC). The prepared copolymers were investigated as flow improvers and pour point depressants (PPD) for crude oil. From the evaluation, it was found that, the maximum depression of PP was obtained by (POMA₂ C₂₂) with long-chain alcohol (C₂₂–OH) from 27°C to 15°C (ΔPP_3000ppm = ?12°C). On the other side, it was remarked that no depression obtained by (POMA₂ C₁₈), which esterified by alcohol (C₁₈–OH) at the same condition. The depression of pour point effectiveness was discussed on the light of polymers structure, molecular weights, and their concentrations. By analysis the results of the rheological flow properties, it was found that the POMA₂ C₂₂ enhanced the Bingham yield values (τ_β). The τ_β for crude oil without additives against 15, 27, and 39°C were 0.286, 0.131, and 0.075 Pa respectively, whereas the τβ for the treated crude oil with POMA₂ C₂₂ were 0.027, 0.022 and 0.010 Pa at 3000 ppm at the same temperatures. By using the photomicrography analysis, it was found that, the wax morphology was greatly modified to fine dispersed crystals of compact size.     

Adsorption of Fe(III) from Aqueous Medium onto Glycine-Modified Chitosan Resin: Equilibrium and Kinetic Studies

The adsorption of Fe(III) onto glycine-modified chitosan (G@Chs) resin has been investigated. The parameters studied include the effects of pH, contact time, and initial metal ion concentrations by batch method. The optimal pH for the adsorption of Fe(III) was found to be 2.5. The results obtained from equilibrium adsorption studies are fitted in various adsorption models such as Langmuir and Freundlich, and each model parameter were evaluated. Kinetics and thermodynamic parameters of the adsorption process were also investigated. The maximum uptake was found to be 0.9 mmol g^?1 at 25°C.     

Stability of Nanoporous Silica Aerogel Dispersion as Wettability Alteration Agent

This work studies the stability of silica aerogel aqueous dispersion for wettability alteration in enhanced oil recovery (EOR) processes. Modified silica aerogel is synthesized with cheap water glass as the precursor, and ambient pressure drying method. Brine composition, brine concentration and temperature of oil reservoirs are the most important parameters for success of wettability alteration processes in EOR. Stability of Silica aerogel aqueous dispersions in NaCl, MgCl₂ and combinations of them are surveyed. Brines at different concentrations, 10000, 20000, 40000 ppm, are used to determine stability conditions. Stability at 30°C and 75°C are surveyed, and the results are reported. DLVO and non-DLVO theories are used for modeling the stability of nanodispersion.     

Antioxidant Activity Degradation,Formulation Optimization,Characterization, and Stability of Equisetum Arvense Extract Nanoemulsion

Equisetum arvense supercritical CO₂ extracts (EAE) contained an initial antioxidant activity of 10.3 mM TEAC that suffered a sharp first order kinetics decay characterized by half-life time (t_1/2) of 1.05 ± 0.03 and 0.86 ± 0.03 weeks at 25 and 4°C, respectively. The aim of the present work was to develop a nanoemulsion formulation for providing EAE protection against deleterious environmental factors and extending its shelf-life functionality. The nanoemulsion area was identified by constructing pseudoternary phase diagrams and response surface methodology was used to optimize the preparation conditions. The best formulation achieved an EAE encapsulation efficiency of 97.5 ± 0.5% and antioxidant activity half-life time (t_1/2) was extended to 12.32 ± 0.40 and 14.56 ± 0.60 weeks at 25 and 4°C, respectively.      

Experimental Study and Numerical Modeling of Rheological and Flow Behavior of Xanthan Gum Solutions Using Artificial Neural Network

This study investigated effect of temperature, concentration, and shear rate on rheological properties of xanthan gum aqueous solutions using a Couette viscometer at temperatures between 25°C and 55°C and concentrations of 0.25 wt% to 1.0 wt%. The Herschel–Bulkley model described very well the non-Newtonian behavior of xanthan gum solutions. Shear rate, temperature, and concentration affected apparent viscosity and an equation was proposed for the temperature and concentration effect valid for each shear rate. This article also presents an artificial neural network (ANN) model to predict apparent viscosity. Based on statistical analysis, the ANN method estimated viscosity with high accuracy and low error.     

Comparison Between Long- and Short-Chain Organoclays for Oil Removal from Salty Waters

Two commercial powdered organoclays, Cloisite 15A and Cloisite 30B, as long-chain organoclays, and two organically modified clays with tetramethylammonium chloride (TMA-clay), as short-chain organoclays were used in this study to investigate their potentials for crude oil removal from salty waters. Batch experiments were performed to examine the effect of contact time and pH on the adsorption process. The results showed that the equilibrium time was reached within 25–30 and 50–55 minutes of contact time for long and short-chain organoclays, respectively. In addition, adsorption isotherms were obtained at an optimum pH value of 11.73 and temperature of 19°C for which initial oil contents varied in the range of 100 to 2000 ppm. Experimental results indicated that the sorption of oil onto Cloisite 15A, Cloisite 30B and the organically modified clays can be described by Freundlich isotherm and oil sorption followed the order of modified Cloisite Na > Cloisite 30B > Cloisite 15A > a modified local clay.      

Influence of Molecular Weight on Mild Steel Corrosion Inhibition Effect by Polyvinyl Alcohol in Hydrochloric Acid Solution

The corrosion inhibition of mild steel in hydrochloric acid solution in the presence of three different molecular weights of polyvinyl alcohol (PVA) designated as PVA-I, PVA-II, and PVA-III corresponding to 14,000, 72,000, and 125,000 g mol^?1, respectively, was investigated using electrochemical impedance spectroscopy, linear polarization resistance (LPR), and potentiodynamic polarization techniques at 25°C. It was found that PVA of different molecular weights inhibited the corrosion of mild steel in the acid environment. Inhibition efficiency (η%) increases with increase in concentration of the polymers. LPR measurements clearly show that inhibition efficiency increases with increasing molecular weight in the order PVA-III > PVA-II > PVA-I. Polarization curves indicate that PVA functions as a mixed inhibitor affecting both the anodic metal dissolution and cathodic hydrogen evolution partial reactions of the corrosion process. The experimental data obtained fitted well into Langmuir adsorption isotherm model. Physical adsorption mechanism is proposed from the thermodynamic (free energy of adsorption) parameters obtained.     

Cinnamoyl Pluronic F127 as a Stimuli-Sensitive Amphiphile

Cinnamoyl Pluronic F127 (CP F127) was prepared by reacting cinnamoyl chloride and Pluronic F127. On the ¹H NMR spectrum of CP F127, 1.2 moiety of cinnamoyl group was found to be attached to one molecule of CP F127. Using pyrene as a fluorescence probe, it was found that not only Pluronic F127 but also CP F127 could be readily assembled into micelles, and the critical micelle concentration was around 0.015 mg/ml and 0.03 mg/ml, respectively. Pluronic F127 in aqueous solution (2% w/v) could form no particles in 10–20°C, but particles (ca. 30 nm in diameter) were detected on a dynamic light scattering machine in 25–40°C possibly due to the thermal micellization. However, CP F127 was assembled into particles (ca. 230 nm) even in the lower temperature range, possibly because of the intermolecular hydrophobic interaction of the cinnamoyl group. The particle size of CP F127 strongly depended on the medium temperature and UV irradiation time. CP F127 was a good emulsifier for the preparation of O/W emulsions. The oil droplet size markedly increased upon UV irradiation (254 nm, 6 W), possibly because of the photo-dimerization of cinnamoyl group, but it was little affected by the temperature change (10–40°C).     

Detecting Mechanochemical Degradation of Nitrocellulose by Combining Dynamic Mechanical Analysis with Mass Spectrometry

Summary: Dynamic mechanical analysis is combined with mass spectrometry to study nitrocellulose under oscillating strain. At a constant temperature (150–160 °C) and frequency (400–600 Hz) nitrocellulose fractures demonstrating a modulus drop and release of products with m/z: 30 and 44. At linear heating (2 °C · min⁻¹) and a frequency of 10–50 Hz similar products are released in two steps, the second of which demonstrates a modulus drop and a temperature increase indicating ignition.

Data for an isothermal dynamic mechanical analysis–mass spectrometry experiment performed at 160 °C.     

Membrane Permeability and Stability of Liposomes Suspended in Shear Flow

The 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) liposome has been characterized in its stability and membrane permeability to 5(6)-carboxyfluorescein (CF) in the shear flow generated in the cone-and-plate geometry. The CF-containing liposomes (CFLs) were 101–323 nm in the mean diameter D _P as measured with the dynamic light scattering (DLS) method. Adsorption of lipids to the cone-and-plate was observed, which clearly depended on the shear stress applied at the shear rate γ up to 1.5 × 10³ s^?1. The permeability of CFLs with D _P of 101 and 117 nm definitely increased at the maximum γ value where the adsorption was negligible. The permeability coefficient of CF at 40°C in the shear flow was 5.7 times larger than that in the static liquid system. The DLS measurements revealed that the size distribution of CFLs with D _P of 101–189 nm was practically unchanged under the shear stress even at 55°C. The results obtained show that the shear stress can permeabilize the CFL membranes with neither structural collapse nor coalescence.     

Adsorptive Removal of Thorium(IV) from Aqueous Solutions Using Synthesized Polyamidoxime Chelating Resin: Equilibrium,Kinetic, and Thermodynamic Studies

In this study, an amidoximated chelating ion exchange resin was prepared by poly-acrylonitrile (PAN) grafted potato starch. The adsorbent characterizations such as specific surface area, pore volume, average pore radius, and Fourier transform infrared (FTIR) spectrum of the resin were measured. The effects of pH, adsorbent dosage, contact time, initial concentration of thorium ion, and temperature on adsorption of thorium ion from aqueous solutions were investigated. Four isotherm models including Langmuir, Freundlich, Dubinin-Radushkevich, and Temkin were applied to analyze the equilibrium isotherm data. The results showed that Langmuir and Temkin models had a good agreement with experimental data. The maximum capacity of the adsorbent using the Langmuir isotherm model was 227.27 mg · g^?1. The kinetic models like pseudo-first-order, pseudo-second-order, Elovich, and intraparticle were examined to describe the adsorption process. The kinetics of the adsorption process was found to follow the pseudo-second-order kinetic model. The thermodynamic parameters (ΔG°, ΔH°, ΔS°) were also calculated using equilibrium constant values at various temperatures (25, 35, 45, 55°C) and the positive value for ΔH° showed an endothermic adsorption process. The study suggests that the prepared adsorbent has promising potential for the removal of thorium from wastewaters.      

Surface Active and Thermodynamic Properties in Relation to the Demulsification Efficiency for Some Ethoxylated Derivatives of Alkyldiamines and Polyalkylenepolyamines

In this work, nine monostearic esters of ethoxylated dialkyle-amine (group I) and ethoxylated polyalkylenepolyamine (group II) nonionic surfactants were prepared and characterized by FTIR spectroscopy and nitrogen content. The 1,4-diaminobutane (DAB), 1,6 diamino hexane (DAH), 1,8-diamino-octane (DAO), diethylenetriamine (DETA), triethylenetetramine (TETA), and tetraethylenepentamine (TEPA) were ethoxylated at 50, 100, 150 ethylene oxide units individually. The ethoxylated products of (group I) reacted with stearic acid to give the monostearate products. The surface tension of the prepared compounds were measured at 25°C and 60°C. The thermodynamic parameters of micellization and adsorption were also calculated. The surface active properties, such as critical micelle concentration (CMC), maximum surface excess concentration (Γ_max), effectiveness of surface tension reduction (π_cmc), and minimum area per molecule at the aqueous solution-air interface (A_min), have been calculated. The surface active and thermodynamic properties of the prepared compounds were correlated to their chemical structure. It was found that CMC decreases when increasing the molecular weight of polyethylene oxide units. Furthermore, the data show that the synthesized surfactants favor adsorption than micellization, so that they can be used as demulsifiers for waxy crude oil emulsion (BSW 18%). In this respect, the demulsification test was carried out and the results of demulsification efficiency were correlated to the chemical composition of the investigated compounds. Some factors that affect the demulsification efficiency were also considered such HLB, concentration and time. The maximum demulsification efficiency (100%) was obtained by DAOE_150-M and TEPAE₁₅₀ at 60 and 45 minutes (300 ppm), respectively.