Gamma-Irradiated Gelatin-Based Films Modified by HEMA for Medical Application

The present article describes the synthesis and characterization of bi-component polymer systems based on gelatin films incorporated with 2-hydroxyethyl methacrylate (HEMA) monomer, developed for medical application. Gelatin films were prepared by the addition of HEMA of different concentrations (0–30 wt.%) and irradiated with various radiation doses (0–5 kGy). Tensile strength and tear strength of the irradiated gelatin films were found to increase with increasing HEMA up to 20 wt.% as well as radiation doses (1 kGy) as optimized. The maximum tensile and tear strengths of irradiated gelatin films with HEMA were found to be 79.1 MPa and 83.2 N/mm, respectively, at the optimum conditions, and these values were about double that of a reference film prepared without additives. In addition, morphological analysis was done by scanning electron microscopy (SEM) and showed how HEMA cemented and was covered with gelatin in the blend. Thermomechanical analysis was carried out to investigate the shifting of glass transition temperature (T_g) towards higher temperature due to HEMA addition, and the effect of this film was tested on the human body in order to determine whether it can be applied for medical purposes.     

Tensile and Thermal Properties of Poly(lactic acid)/Eggshell Powder Composite Films

Biodegradable composite films of poly(lactic acid) (PLA)/eggshell powder (ESP) were prepared by the composite film casting method using chloroform as the solvent. ESP was loaded in PLA in 1 to 5 wt.%. The films were subjected to tensile, FT-IR spectral, thermogravimetric, X-ray, and microscopic analyses. The tensile strength and modulus of the composite films were found to be higher than those of PLA and increased with ESP content up to 4 wt.% and then decreased. A reverse trend was observed in the case of percentage elongation at break. The X-ray diffractograms of the composite films indicated an increase in crystallinity with ESP content. The optical micrographs indicated uniform distribution of ESP particles in the composite films. However, the fractographs indicated agglomeration of ESP particles at 5 wt.% loading. The FT-IR spectra revealed no specific interactions between PLA and ESP. The thermal stability of the composite films increased with ESP content.     

Photo-oxidation behaviour of polyethylene/multi-wall carbon nanotube composite films

The resistance to accelerated photo-oxidation of polyethylene/multi-walled carbon nanotubes (MW-CNTs) composite films was compared with the photo-oxidation behaviour of pristine polyethylene film. The polyethylene/MW-CNTs films containing different CNTs loading were subjected to accelerated UV-B exposure. At short exposure time, i.e. under 200 h, the rates of carbonyl formation are very similar to that observed for pristine polyethylene film but at longer irradiation times the carbonyl formation increases for lower MW-CNTs contents (0.1, 0.2 and 0.5% wt./wt.), and decreases for higher MW-CNTs contents (1 and 2% wt./wt.). By adding a UV-stabilizer to the films their photo-oxidation rates are drastically decreased also at low MW-CNTs concentration. Addition of a metal deactivator (MD) produced no observable effect.     

Preparation of LDPE-acetylated/butyrylated starch blend blow films and characterization

Development of modified plastics has been studied through the LDPE-acylated starch blend films to examine the effect of different acyl groups and degrees of substitution(DS) on properties of films.Corn starch was modified with acetyl and butyryl groups and films were prepared by blending acylated starch with low density polyethylene(LDPE).Systematic studies were done to observe the effect of acyl groups,DS and starch concentration on the properties and biodegradability of the blend films.It was observed that blend films containing 5% acetylated and butyrylated starches of high DS(2.5,1.7) maintained 75% and 83% of tensile strength of LDPE films.Thermal analysis results indicated that acetylated and butyrylated starch blend films decomposed at 370 °C and 389 °C which were higher than the decomposition temperature of native starch film(349 °C).Scanning electron micrographs of blend films containing high DS acylated starch showed well dispersed starch particles due to improvement in dispersion between starch and LDPE.Water absorption capacity of high DS acetylated and butyrylated starch blend films(4.18% and 3.76%,respectively) was lower than that of native starch films(5%).This study has an advantage because of blown films prepared can be integrated with the present manufacturing systems without any other requirement.     

Properties of poly(acrylamide)/TEMPO-oxidized cellulose nanofibril composite films

Self-standing composite films consisting of 2,2,6,6-tetramethylpiperidine-1-oxyl-oxidized cellulose nanofibril (TOCN) and anionic poly(acrylamide) (PAM) in various weight ratios were prepared by casting and drying of homogeneous mixtures of aqueous TOCN dispersion and PAM solution. PAM/TOCN composite films consisting of 25 % PAM and 75 % TOCN had clearly higher Young’s modulus (13.9 GPa) and tensile strength (266 MPa) than 100 % TOCN film (10.8 GPa and 223 MPa, respectively) or 100 % PAM film (4.9 GPa and 78 MPa, respectively), showing that PAM molecules have mechanical reinforcement ability in TOCN matrix. Some attractive interactions are likely formed between TOCN element surfaces and PAM molecules. In contrast, no such mechanical improvements were observed for poly(vinyl alcohol)/TOCN or oxidized starch/TOCN composite films prepared as references. Moreover, the mechanical properties of the PAM/TOCN composite films were further improved by controlling molecular mass and branching degree of the PAM. The high optical transparency and low coefficient of thermal expansion of the 100 % TOCN film were mostly maintained in the TOCN composite film containing 25 % PAM.     

Properties and morphologies of UV‐cured epoxy acrylate blend films containing hyperbranched polyurethane acrylate/hyperbranched polyester

The properties and morphologies of UV‐cured epoxy acrylate (EB600) blend films containing hyperbranched polyurethane acrylate (HUA)/hyperbranched polyester (HPE) were investigated. A small amount of HUA added to EB600 improved both the tensile strength and elongation at break without damaging its storage modulus (E′). The highest tensile strength of 31.9 MPa and an elongation at break around two times that of cured pure EB600 were obtained for the EB600‐based film blended with 10% HUA. Its log E′ (MPa) value was measured to be 9.48, that is, about 98% of that of the cured EB600 film. The impact strength and critical stress intensity factor (K_1c) of the blends were investigated. A 10 wt % HUA content led to a K_1c value 1.75 times that of the neat EB600 resin, and the impact strength of the EB600/HPE blends increased from 0.84 to 0.95 kJ m^?1 with only 5 wt % HPE addition. The toughening effects of HUA and HPE on EB600 were demonstrated by scanning electron microscopy photographs of the fracture surfaces of films. Moreover, for the toughening mechanism of HPE to EB600, it was suggested that the HPE particles, as a second phase in the cured EB600 film, were deformed in a cold drawing, which was caused by the difference between the elastic moduli of HPE and EB600. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3159–3170, 2005     

Synthesis,Characterization and Comparison of Properties of Novel Fluorinated Polyimides Derived from Bisphenol–A‐di(phthaleic anhydride)

Four new poly(etherimide)s have been synthesized by reaction with commercially available bisphenol‐A‐(diphthaleic anhydride) (BPADA) with four different kinds of diamines, namely 4,4′‐bis(p‐aminophenoxy‐3,3″‐trifluoromethyl) terphenyl,4,4′‐bis(3″‐trifluoromethyl‐p‐aminobiphenyl ether)biphenyl,2,6‐bis(3′‐trifluoromethyl‐p‐aminobiphenyl ether)pyridine, 2,5‐bis(3′‐trifluoromethyl‐p‐aminobiphenylether)thiopene. The poly(etherimide)s are named as 1a, 1b, 1c and 1d, respectively. The synthesized polyimides show good solubility in various organic solvents. The polyimide films had low water absorption of 0.19–0.30% and low dielectric constant of 2.79–3.1 at 1 MHz. These polyimides showed very high thermal stability with decomposition temperature (5% wt loss) up to 522°C in nitrogen. Transparent thin films of these polyimides exhibited tensile strength up to 97 MPa, a modulus of elasticity up to 1.56 GPa and elongation at break up to 20%.     

Studies on the photo-oxidative degradation of LDPE films in the presence of oxidised polyethylene

This paper reports the results of photo-oxidative degradation studies of LDPE in the presence of varying amounts of oxidised polyethylene (OPE), which was prepared by heating LDPE films containing 0.1% cobalt stearate in oxygen atmosphere at 100 °C. OPE, with a CI of 12 was used as an additive for LDPE. Varying amounts of OPE (0.5-5%) were blended with polyethylene in an extruder and films of 70 μm thickness were prepared by film blowing process. The physico-chemical properties of the films were evaluated and these were found to be proportional to the amount of OPE. The films thus obtained were subjected to UV-B exposure at 30 °C for extended time periods. The chemical and physical changes induced by UV exposure were followed by monitoring the changes in mechanical properties (tensile strength and elongation at break), carbonyl index (CI), morphology, molecular weight, MFI and DSC crystallinity. Incorporation of OPE was found to be effective in initiating the photo-degradation of LDPE in relatively short span of time and the degradation was found to be proportional to the amount of OPE in the formulation.     

Effect of benzil and cobalt stearate on the aging of low-density polyethylene films

We report an investigation of the effect of benzil and cobalt stearate on the degradation behaviour of LDPE films. Thin films (70 μ) containing these additives were prepared by sheeting process. The effect of heating, exposure to UV-B and natural weathering of LDPE films in the presence/absence of additives was investigated. Changes in the tensile properties, carbonyl index and density were used to investigate the degradation behaviour. Attempts have been made to correlate the results as a function of mixed additives. In contrast to the activity of typical triplet activators, benzil was found to be incapable of initiating thermal- or photo-degradation of LDPE films. However, an accelerated rate of oxidation was observed, primarily due to cobalt stearate, in the case of compositions containing a combination of benzil and cobalt stearate. All samples were found to be more susceptible to thermo-oxidation than to UV or natural weathering.     

Synthesis and Properties of Novel Aromatic Copolyamides Containing Phthalazinone Moiety

A series of novel aromatic copolyamides were synthesized by the direct polycondensation of 2‐(4‐carboxyphenyl)‐4‐[4‐(4‐carboxyphenoxyl)phenyl]‐phthalazinone (1), terephthalic acid (TPA), and four commercial diamines. The inherent viscosities of the polyamides were between 0.79～1.56 dL/g. Introduction of the non‐coplanar phthalazinone segments into the main chains remarkably decreased the crystallinity and improved the solubility of the copolyamides. When the percentage of 1 in the diacid monomers was above 50%, the copolymers were soluble in aprotic polar solvents, such as N‐methyl‐pyrrolidinone and N,N‐dimethylacetamide. The copolyamides showed high thermal properties associated with the glass transition temperatures in the range of 276～337°C and 10% wt loss temperatures in nitrogen over 496°C. Some polymer films cast from NMP solution had tensile strengths up to 123.4 MPa, initial moduli up to 2.10 GPa, and elongation at break values up to 9.6%.     

Efficient alternative of antimicrobial nanocomposites based on cellulose acetate/Cu-NPs

The current research presents an efficient, cheap, and safe antimicrobial material for widespread use based on copper nanoparticles (Cu-NPs) loaded on cellulose acetate (CA) matrix. A reduction process of CuSO₄·5H₂O has been performed to prepare Cu-NPs. The nanosized copper particles included oxidized Cu (15–20 nm). Two different loads of Cu-NPs were used in this study, 2% and 6% mol.%. The presence of Cu-NPs incorporated with CA films slightly affected the tensile index of the films, where low and high-loaded Cu-NPs enhanced the tensile index by small values ranged from 0.640 to 0.650 and 0.667, respectively. A study on the antibacterial activity of these nanocomposites was carried out for Staphylococcus aureus, Pseudomonas aeruginosa, and Candida albicans. It has been found that CA containing Cu-NPs (2%) exhibited the highest antimicrobial activity against all test microbes including S. aeureus (21 mm), P. aeruginosa (18 mm), C. albicans (19 mm), and Aspergillus niger (15 mm). Results also revealed that CA film with 6% exhibited lower activity than film with 2% Cu-NPs. The morphological properties of CA/Cu-NPs films were characterized by scanning electron microscopy and transmission electron microscope in addition to X-ray diffraction. Low-loaded Cu-NPs showed homogenous distribution through CA matrix while, the high-loaded Cu-NPs were agglomerated through CA matrix. Thermal properties illustrated the enhancement of thermal stability of the film with increasing the loaded Cu-NPs.     

Natural weathering test for films of various formulations of low density polyethylene (LDPE) and linear low density polyethylene (LLDPE)

Natural (outdoor) weathering test was performed to investigate the UV stability of thin films (0.06 mm) of linear low density polyethylene (LLDPE) and low density polyethylene (LDPE). The PE films were prepared from various formulations of LLDPE and LDPE resins. Some of these films contained a single high molecular mass HALS only, along with a primary antioxidant (i.e. Irganox 1010) and a secondary antioxidant (i.e. Irgafos 168 or Alkanox TNPP), while others contained HALS and UVA (i.e. Chimassorb 81 or Tinuvin P or Tinuvin 326) along with these antioxidants. The HALS used was either an oligomeric or a synergistic mixture of a high molecular mass (HMM) hindered amine stabilizer and co-additives. The UV stability was investigated by exposing the prepared films at 45° towards south in the direct sunshine up to 365 days. Fifty percent of tensile strength retention was determined for all these exposed films and it was found that the films containing a single HALS gained improved UV stability by about two to 12 fold over the pure films. On the other hand, films that contained a combination of HALS and UVA obtained further improved UV stability over the films containing a single HALS (both have antioxidants). Films containing a single HALS reached 50% TS retention within 205 days, whereas, films containing a combination of HALS and UVA reached 50% TS retention within 590 days, which is about three times further improvement in UV stability.     

Synthesis of a Novel Chitosan/Basil Oil Blend and Development of Novel Low Density Poly Ethylene/Chitosan/Basil Oil Active Packaging Films Following a Melt-Extrusion Process for Enhancing Chicken Breast Fillets Shelf-Life

An innovative process for the adsorption of the hydrophobic Basil-Oil (BO) into the hydrophilic food byproduct chitosan (CS) and the development of an advanced low-density polyethylene/chitosan/basil-oil (LDPE/CS_BO) active packaging film was investigated in this work. The idea of this study was the use of the BO as both a bioactive agent and a compatibilizer. The CS was modified to a CS_BO hydrophobic blend via a green evaporation/adsorption process. This blend was incorporated directly in the LDPE to produce films with advanced properties. All the obtained composite films exhibited improved packaging properties. The film with 10% CS_BO content exhibited the best packaging properties, i.e., 33.0% higher tensile stress, 31.0% higher water barrier, 54.3% higher oxygen barrier, and 12.3% higher antioxidant activity values compared to the corresponding values of the LDPE films. The lipid oxidation values of chicken breast fillets which were packaged under vacuum using this film were measured after seven and after fourteen days of storage. These values were found to be lower by around 41% and 45%, respectively, compared with the corresponding lipid oxidation values of pure LDPE film.     

Synthesis and Characterization of Acrylated Epoxidized Castor Oil Nanocomposites

Renewable resource-based epoxidized castor oil (ECO) was synthesized and used as a prime material to develop acrylated epoxidized castor oil (AECO) networks. AECO nanocomposites were prepared by the sol-gel method from organo-modified montmorillonite (OMMT) clay and silane. It was found that the AECO/1 wt.% OMMT system increased in tensile strength from 28 to 37 MPa and flexural strength from 54 to 63 MPa as compared with the AECO system. The non-isothermal cure kinetics of the bio-based systems was studied using differential scanning calorimetry. The activation energy of the AECO/OMMT system obtained from Kissinger and Flynn-Wall-Ozawa models is lower than that of AECO system.     

Preparation and characterization of composites from starch with sugarcane bagasse nanofibres

This paper reports on the results of using unbleached sugar cane bagasse nanofibres (average diameter 26.5 nm; aspect ratio 247 assuming a dry fibre density of 1,500 kg/m³) to improve the physico-chemical properties of starch-based films. The addition of bagasse nanofibres (2.5 to 20 wt%) to modified potato starch (i.e. soluble starch) reduced the moisture uptake by up to 17 % at 58 % relative humidity. The film’s tensile strength and Young’s modulus increased by up to 100 % (3.1 to 6.2 MPa) and 300 % (66.3 to 198.3 MPa) respectively with 10 and 20 wt% fibre addition. However, the strain at yield dropped by 50 % for the film containing 10 wt% fibre. Models for composite materials were used to account for the strong interactions between the nanofibres and the starch matrix. The storage and loss moduli as well as the glass transition temperature (T_g) obtained from dynamic mechanical thermal analysis, were increased with the starch-nanofibre films indicating decreased starch chain mobility due to the interacting effect of the nanofibres. Evidence of the existence of strong interactions between the starch matrix and the nanofibres was revealed from detailed Fourier transform infra-red and scanning electron microscopic evaluation.     

Transparent acryl–clay nanohybrid films with low thermal expansion coefficient

The aim of this study was to prepare transparent nanohybrid films with low coefficient of thermal expansion (low CTE), which consist of acryl resin and nanosized clay. The hybrid films with different clay contents were prepared by UV curing of tricyclodecane dimethanol diacrylate (TCDDMDA) including nanosized clay. All obtained films were transparent similar to pure poly(TCDDMDA). In addition, the film containing 40 wt.% of clay showed a low CTE of 10 ppm/K in 150–200 °C, which is similar to that of inorganic materials such as glass. The significant property improvement is related to shape effect and orientation of clay in polymer matrix. Wide-angle X-ray diffraction measurement was carried out to investigate orientation of nanosized clay in polymer matrix. From this measurement, it was confirmed that the clay platelets were oriented parallel with film surface with increasing clay content, and orientation coefficient of the clay in polymer matrix reached to f?=?0.65 for the hybrid film containing 40 wt.% of clay. Though, in comparison with the matrix, the flexibility of the hybrid film evaluated by the wind roll test with steel bar was lowered by increase of clay content, the hybrid film containing 40 wt.% of clay could be rewound with steel bar 10 mm across, and its flexibility was retained.     

Effect of Manganese on Radiation Vulcanization of Natural Rubber

Manganese was added as a promoter to investigate physico-mechanical properties of radiation-vulcanized natural rubber latex (RVNRL) films. RVNRL films were prepared by the addition of Mn with the concentration range 0–30 ppm to natural rubber latex and irradiated with various radiation doses (0–20 kGy). Tensile strength, tear strength, and cross-linking density of the irradiated rubber films increased with increasing the concentration of Mn ions as well as radiation doses. In contrast, elongation at break, permanent set, and swelling ratio of the films were decreased under the same conditions. The concentration of Mn ions and radiation doses were optimized and found to be 20 ppm and 12 kGy, respectively. The maximum tensile and tear strengths of irradiated rubber films were observed as 29.12 MPa and 44.78 N/mm, respectively at the optimum conditions. The mechanical properties of the films increased markedly with the addition of Mn until they attained the highest values of 33.88 MPa and 54.77 N/mm, respectively. These enhancements, which reached approximately 20% at the most favorable conditions, can be explained by the effect of transition metals in view of Fajan’s rules regarding the covalent character of ionic bonds and suggest that the higher the difference in charges between cation and anion, the higher the ability to form distortion or polarization of ions.     

Modification of hydrophilic poly(vinyl alcohol) film via blending with hydrophobic poly(butyl acrylate-co-methyl methacrylate)

A series of poly(vinyl alcohol)/poly(butyl acrylate-co-methyl methacrylate) [PVA/P(BA-co-MMA)] blend films with different P(BA-co-MMA) content were prepared by the solution casting method. Surface morphologies of the PVA/P(BA-co-MMA) blend films were studied by scanning electron microscopy and atomic force microscopy. Thermal, mechanical, and chemical properties of PVA/P(BA-co-MMA) blend films were investigated by differential scanning calorimeter, thermogravimetric analysis, tensile tests, and surface contact angle tests. It was revealed that the introduction of P(BA-co-MMA) could affect the properties of the PVA films. The results also showed that, when P(BA-co-MMA) mole content is 3 %, the tensile strength and the surface contact angle of the polymer blend film are 20.4 MPa and 43.5°, respectively, suggesting that the polymer blend film holds both a better mechanical property and a better chemical property.     

Monomer and Radiation-Mediated Sago Starch Blend Film: Mechanical and Thermal Property Optimization

Bio-blend films were prepared with sago starch and N-vinyl-2-pyrrolidone (NVP) by the casting method, varying the concentrations of sago starch (100 to 93%) and NVP (0 to 7%). The formulations were designated as F1 (starch 100%), F2 (starch 97%), F3 (starch 95%), and F4 (starch 97%). The highest tensile strength (TS), tensile modulus (TM), and elongation at break (Eb%) were found correspondingly to be 30.47 MPa, 407.74 MPa, and 8.25% for the F3 formulation. Gamma radiation was applied to films to modify their performance through grafting and cross-linking. The highest TS, TM, and Eb% were found at 500 krad dose and they were 38.12 MPa, 481.00 MPa, and 9.78%, respectively for F3 formulation. The water uptake nature and thermal properties of the treated and untreated films were also investigated.     

LDPE/EVA/graphene nanocomposites with enhanced mechanical and gas permeability properties

In the present work, graphene oxide (GO) and reduced graphene oxide (RGO) were incorporated at low‐density polyethylene (LDPE)/ethylene vinyl acetate (EVA) copolymer blend using solution casting method. Monolayer GO with 1‐nm thickness and good transparency was synthesized using the well‐known Hummers's method. Fourier transform infrared and X‐ray photoelectron spectroscopy data exhibited efficient reduction of GO with almost high C/O ratio of RGO. Scanning electron microscopy showed the well distribution of GO and RGO within LDPE/EVA polymer matrix. The integrating effects of GO and RGO on mechanical and gas permeability of prepared films were examined. Young's modulus of nanocomposites are improved 65% and 92% by adding 7 wt% of GO and RGO, respectively. The tensile measurements showed that maximum tensile strength emerged in 3 wt% of loading for RGO and 5 wt% for GO. The measured oxygen and carbon dioxide permeability represented noticeably the attenuation of gas permeability in composite films compared with pristine LDPE/EVA blend. Copyright © 2015 John Wiley & Sons, Ltd.