Chain‐extended,hydroxyterminated‐polybutadiene‐based polyurethaneureas: Synthesis,reaction kinetics,and properties

Hydroxyterminated‐polybutadiene‐based prepolyurethanes were prepared with two different catalysts, dibutyltindilaurate (DBTDL) and triethylamine (TEA); chain extension of the prepolyurethanes followed with two different aromatic diamines, oxydianiline and 4,4′‐diaminodiphenylsulfone, in various concentrations. The prepolyurethane synthesis followed second‐order kinetics, with the DBTDL catalyst showing better efficiency for urethane formation than TEA. TEA‐catalyzed synthesis suffered from the self‐association of isocyanates as a major side reaction, following second‐order kinetics with respect to isocyanate concentration. Although there was a gradual increase in the intrinsic viscosity during prepolyurethane synthesis in the presence of DBTDL, the intrinsic viscosity remained almost constant with the progress of the reaction in the presence of TEA. The tensile properties of prepolyurethane and polyurethaneureas synthesized in DBTDL‐catalyzed reactions were higher than the properties of those synthesized in TEA‐catalyzed reactions. The variation of the tensile strength with the diamine concentration was correlated with the crosslink density and sol fraction. The solubility of the hard segment of polyurethaneurea in the reaction medium appeared to be important in influencing the tensile properties. The effects of the diamine concentration (chain extender) on the diffusion coefficient and activation energy of diffusion of toluene in polyurethaneureas were studied. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2978–2992, 2001     

Fluoropolyethers end‐capped by polar functional groups. III. Kinetics of the reactions of hydroxy‐terminated fluoropolyethers and model fluorinated alcohols with cyclohexyl isocyanate catalyzed by organotin compounds

The kinetics of the dibutyltin dilaurate (DBTDL)‐catalyzed urethane formation reactions of cyclohexyl isocyanate (CHI) with model monofunctional fluorinated alcohols and fluoropolyether diol Z‐DOL H‐1000 of various molecular weights (100–1084 g mol^?1) in different solvents were studied. IR spectroscopy and chemical titration methods were used for measuring the rate of the total NCO disappearance at 30–60 °C. The effects of the reagents and DBTDL catalyst concentrations, the solvent and hydroxyl‐containing compound nature, and the temperature on the reaction rate and mechanism were investigated. Depending on the initial reagent concentration and solvent, the reactions could be well described by zero‐order, first‐order, second‐order, or more complex equations. The reaction mechanism, including the formation of intermediate ternary or binary complexes of reagents with the tin catalyst, could vary with the concentration and solvent and even during the reaction. The results were treated with a rate expression analogous to those used for enzymatic reactions. Under the explored conditions, the rate of the uncatalyzed reaction of fluorinated alcohols with CHI was negligible. Moreover, there was no allophanate formation, nor were there other side reactions, catalysis by urethane in the absence of DBTDL, or a synergetic effect in the presence of the tin catalyst. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3771–3795, 2002     

Catalysis of N‐Methylaniline‐Blocked Polyisocyanate‐Hydroxyl‐Terminated Polybutadiene Cure Reaction

Catalysis of cure reaction between N‐methylaniline‐blocked polyisocyanate and hydroxyl‐terminated polybutadiene was investigated using a variety of tertiary amine and organotin catalysts. The catalytic activity of amine and organotin compounds was determined from the cure‐time results. It was found that the activity of the catalyst depends upon the steric constrain around the catalytic center. The organotin compounds showed higher catalytic activity than the amine catalysts. FTIR results obtained under isothermal condition revealed that DABCO selectively catalyze the urethane formation reaction, whereas DBTDL catalyze both the allophanate formation and urethane formation reactions during curing process. The synergistic effect of amine and organotin mixed catalysts on the cure reaction was also investigated.     

Kinetic Studies on the Urethane Reaction of Propanediol with Isocyanate in Nitrogenous Solvents

The urethane reactions of 1,2-propanediol, 1,3-propanediol, and n-propanol with phenyl isocyanate were respectively carried out in nitrogenous solvents. In situ FT-IR was used to monitor the reactions, and rate constants were determined. It was shown that the reaction rate of 1,2-propanediol was fastest, followed by the reaction rates of 1,3-propanediol and n-propanol. After that, activation energy (E_a), activation enthalpy (ΔH), and activation entropy (ΔS) were calculated. It was found that these thermodynamic parameters for 1,2-propanediol and 1,3-propanediol are very similar, but they were very different from those of n-propanol, which is very useful to understand the urethane reaction mechanism.     

Research on the Blocking Reaction Kinetics and Mechanism of Aqueous Polyurethane Micelles Blocked by 2,4,6-Trichlorophenol

The blocked terminal-isocyanate (NCO) aqueous polyurethane micelles were prepared by using the 2,6-hexamethylene diisocyanate (HDI), polyethylene glycol (PEG), dimethylol propionic acid (DMPA), and 2,4,6-trichlorophenol (TCP) as blocking agent. This paper was focused on the kinetics research of the TCP blocking terminal-NCO of pre-polymer, which occurred during the preparation process of TCP blocked aqueous polyurethane micelles. The kinetics parameters were obtained in the absence and presence of dibutyl tin dilaurate (DBTDL) as catalyst, respectively. Furthermore, the mechanism for TCP blocking terminal-NCO of pre-polymer was explored. The results showed that the blocking reaction was second order reaction, and the reaction activation energy was 43.890 KJ/mol without catalyst. In the presence of DBTDL, the blocking reaction activation energy was reduced to 34.412 KJ/mol, and the reaction rate was improved significantly. In addition, TCP blocking terminal-NCO of pre-polymer could be ascribed to the nucleophilic addition between nucleophilic phenolic hydroxyl of TCP and the carbon atom of -NCO group.     

Fluoropolyethers end‐capped by polar functional groups. II. Effect of catalyst and reagents concentration,solvent nature,and temperature on reaction kinetics of α,ω‐bis(hydroxy)‐terminated fluoropolyethers with cycloalyphatic and aromatic diisocyanates

A comparative kinetic study of the dibutyltin dilaurate (DBTDL) and 1,4‐diazabicyclo[2,2,2]octane (DABCO) catalyzed reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers (FPEs)—Z‐DOLs and Z‐DOL TXs—of various molecular weights and purity, with 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI), isophorone diisocyanate (IPDI) and 2,4‐toluene diisocyanate (TDI) was carried out in different solvents. An analytical method was used to follow the kinetics of the reactions at four different temperatures. The rate of NCO disappearance measured by two independent methods—IR spectroscopy and chemical titration were found to be very close. Straight proportionality between rate constants k_cat and catalyst concentration was found. But in some cases for the DBTDL catalyzed reactions effect of catalyst saturation along with appearance of the limiting DBTDL concentration C_lim below which the rate of reaction was close to zero were observed. Reactivity of Z‐DOLs in the tin‐catalyzed urethane reactions was found to decrease with their storage time at RT due to the slow hydrolysis of the end  COOR groups impurities, which give the corresponding acids that act as a strong inhibitor of the DBTDL activity. These acid admixtures have no influence on the DABCO catalyzed reactions. For the DBTDL and DABCO catalyzed reactions of Z‐DOLs with IPDI the dependence of effective rate constants k_eff (where k_eff = k_cat · 0.01/[DBTDL] and catalyst concentration is taken in mol % based on IPDI) on total reagents concentration were found to be described by curves with a maximum. Critical reagents concentration, after which the relationship k_eff = f (C) changes from proportional to inverse proportional, seems do not substantially depend on the solvent nature. Hydrogenated analog poly(ethylene glycol) MW 400 (PEG‐400) differs greatly from Z‐DOLs: only steady decrease of k_eff was observed with increase of reagents concentration C from 5 up to 95 wt %. Activation energies for all the studied reactions are within the range of 10.8–16.7 kcal/mol. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2579–2602, 2000     

DSC study on the effect of isocyanates and catalysts on the HTPB cure reaction

The urethane forming cure reactions of hydroxyl terminated polybutadiene (HTPB) binder with three different isocyanate curatives, viz., toluene diisocyanate (TDI), isophorone diisocyanate (IPDI) and 4,4-methylene bis(cyclohexyl isocyanate) (MCHI), were investigated by differential scanning calorimetry (DSC). The effect of two cure catalysts, viz., dibutyl tin dilaurate (DBTDL) and ferrric tris-acetylacetonate (FeAA) on the cure reactions was also studied. Cure kinetics was evaluated using the multiple heating rate Ozawa method. The reactivities of the three isocyanates and catalytic efficiencies were compared based on the DSC reaction temperatures, activation energies and rate constants. Viscosity build-up in these systems at isothermal temperature was also studied and compared with the results from DSC.     

Kinetic study of polyurethanes formation by using differential scanning calorimetry

Kinetics of polyurethane formation between several polyols and isocyanates with dibutyltin dilaurate (DBTDL) as the curing catalyst, were studied in the bulk state by differential scanning calorimetry (DSC) using an improved method of interpretation. The molar enthalpy of urethane formation from secondary hydroxyl groups and aliphatic isocyanates is 72±3 kJ mol^-1 and for aromatic isocyanates it is 55±2 kJ mol^-1 . In the case of a single second order reaction for aliphatic isocyanates reaction, activation energy is 70±5 kJ mol^-1 with oxypropylated polyols and 50±3 kJ mol^-1 with Castor oil. For aromatic isocyanates and oxypropylated polyols the activation energy is higher around 77 kJ mol^-1 . In the case of two parallel reactions (situation for IPDI and TDI 2-4) best fits are observed considering two different activation energies.     

Catalysis of the cure reaction of bisphenol A dicyanate. A DSC study

The kinetics of the thermal cure reaction of Bisphenol A dicyanate (BACY) in presence of various transition metal acetyl acetonates and dibutyl tin dilaurate (DBTDL) was investigated using dynamic differential scanning calorimetry (DSC). The cure reaction involved a pregel stage corresponding to around 60% conversion and a postgel stage beyond that. Influence of nature and concentration of catalysts on the cure characteristics was examined and compared with the uncatalyzed thermal cure reaction. The activation energy (E), preexponential factor (A), and order of reaction (n) were computed by the Coats–Redfern method. A kinetic compensation correction was applied to the data in both stages to normalize the E values. The normalized activation energy showed a systematic decrease with increase in catalyst concentration. The exponential relationship between E and catalyst concentration substantiated the high propensity of the system for catalysis. At fixed concentration of the catalyst, the catalytic efficiency as measured by the decrease in E value showed dependency on the nature of the coordinated metal and stability of the acetyl acetonate complex. Among the acetyl acetonates, for a given oxidation state of the metal ions, E decreased with decrease in the stability of the complex. A linear relationship was found to exist between activation energy and the gel temperature for all the systems. Manganese and iron acetyl acetonates were identified as the most efficient catalysts. In comparison to DBTDL, ferric acetyl acetonate proved to be a more efficient catalyst. The activation parameters computed using the Coats–Redfern method agreed well with the results from two other well known integral equations. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1103–1114, 1999     

Fluoropolyethers end‐capped by polar functional groups. IV. A novel approach to the evaluation of reactivities of hydroxy‐terminated ethoxylated fluoropolyethers in the tin(IV)‐catalyzed reactions with isophorone diisocyanate

The effect of catalyst dibutyltin dilaurate (DBTDL) on the kinetics of urethane formation reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers Fomblin® Z‐DOL TXs (FPEs) of various molecular weights and poly(oxyethylene) glycol PEG‐400 with isophorone diisocyanate (IPDI) in hexafluoroxylene (HFX) and tetrahydrofuran (THF) at 40 °C and NCO:OH = 2:1 have been studied in a broad range of catalyst (0.10–9.00) ×10^?4 M and total reagents (10.0–60.1 wt %) concentrations. The rate of tin‐catalyzed second‐order reactions (with respect to diol and diisocyanate) was found to be proportional to the square root of catalyst concentration [DBTDL]^0.5 both in low polar (HFX) and polar (THF) solvents. Effect of catalyst saturation was revealed for all the reaction systems at higher DBTDL concentrations as well as the appearance of the limiting catalyst concentrations C_lim below which the rates of reaction were close to zero. Based on these findings new effective rate coefficients have been derived k = k_cat/(C ? C) that are independent of the total reagent concentration in the range of 10.0–60.1 wt % ([OH] = 0.10–0.91 equiv/L). This new approach highlights that the rate of the tin‐catalyzed urethane formation reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers Z‐DOL TXs with IPDI in HFX at 40 °C and NCO:OH = 2:1 increases significantly with increasing MW of FPE from 776 up to 3405. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5354–5371, 2004     

Fluoropolyethers end‐capped by polar functional groups. I. Kinetic approach to the reaction of hydroxy‐terminated fluoropolyethers with cycloalyphatic and aromatic diisocyanates

Urethane reactions of cycloaliphatic and aromatic diisocyanates with hydroxy‐terminated fluoropolyethers (FPEs) of various molecular weights and structure, at NCO : OH = 2, have been studied by monitoring, by IR analysis, the rate of decrease in NCO absorbance at 2264–2268 cm⁻¹. Different diisocyanates have been tested, among them the following: 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI); 5‐isocyanato‐1,3,3‐trimethylcyclohexylmethyl isocyanate or isophorone diisocyanate (IPDI); 2,4‐toluene diisocyanate (TDI). Ethyl acetate (EA), methyl isobutyl ketone (MIBK), and hexafluoroxylene (HFX) have been used as solvents in presence of dibutyltin dilaurate (DBTDL) or 1,4‐diazabicyclo[2.2.2]octane (DABCO) as catalysts. These reactions gave rise to NCO‐end‐capped FPE–oligourethanes. Preliminary solubility tests for HO‐terminated FPEs in various solvents made it possible to select proper candidates for carrying out reaction in homogeneous conditions at high concentrations of reagents (30–50% w/w). The second‐order kinetic mechanism was shown to be valid. Positive deviations from linearity for the second‐order kinetics around 40–80% conversion, found for most of the FPE diols, were attributed to the autocatalysis of the isocyanate–hydroxyl reaction by the arising urethane groups. Uncatalyzed reactions with cycloaliphatic diisocyanates are very slow at 40°C. The tertiary amine DABCO is a much less effective catalyst than DBTDL. FPEs having terminal OH groups separated from the perfluorinated main molecular chain by  (OCH₂CH₂)_n segments (n = 1–2) are generally more reactive than FPEs with end  CH₂OH groups. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 557–570, 1999     

Effect of catalysts on the reaction of an aliphatic isocyanate and water

The kinetics of the reaction of aliphatic isocyanate with water were investigated with hexyl isocyanate as a model compound. The kinetic study was carried out with a titration method to determine the concentration of the isocyanate group as a function of time. Gas chromatography was used to augment the kinetic data obtained from the titration method. The effects of an organic acid [p‐toluene sulfonic acid monohydrate (p‐TSA)], a tertiary amine {diazabicyclo[2.2.2]octane (DABCO)}, and an organotin compound [dibutyltin dilaurate (DBTDL)] on the reaction were investigated for the conversion of isocyanate to a urea. Under the reaction conditions in this study, urea was the only product observed. The rate constants indicated that p‐TSA had low catalytic activity, DABCO had intermediate catalytic activity, and DBTDL had high catalytic activity. A reaction mechanism was proposed for each of the catalysts. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1677–1688, 2002     

添加剂对EO/THF共聚醚聚氨酯热氧降解的影响

添加剂对EO/THF共聚醚聚氨酯热氧降解的影响     

Ring-opening polymerization of cyclic urethanes and ring-closing depolymerization of the respective polyurethanes

The cationic ring-opening polymerization of trimethylene urethane (tetrahydro-2 H-1,3-oxazin-2-one) in the melt with methyl trifluoromethanesulfonate as initiator results in poly(trimethylene urethane) in yields of ≈70%. Under the same reaction conditions 2,2-dimethyltrimethylene urethane (5,5-dimethyltetrahydro-2H-1,3-oxazin-2-one) cannot be polymerized. Poly(2,2-dimethyltrimethylene urethane), however, was obtained via polycondensation polymerization. Both polymers exhibit a uniform microstructure as deduced from NMR spectroscopic analysis. Ring-closing depolymerization in the melt with dibutyltin dimethoxide or titanium tetraisopropoxide at 140°C results the respective monomers in yields of ≈90%.     

Tetrabutylammonium bromide: An efficient, green and novel media for polycondensation of 4-(4-dimethylaminophenyl)-1,2,4-triazolidine-3,5-dione with diisocyanates

This is the first report of application of molten ionic liquid (MIL) for the synthesis of heterocyclic polyureas. An inexpensive and readily available MIL, tetrabutylammonium bromide (TBAB) was used for the synthesis of polymers. Therefore, polycondensation of 4-(4-dimethylaminophenyl)-1,2,4-triazolidine-3,5-dione (DAPTD) with various commercially available diisocyanates was performed in molten TBAB with or without dibutyltin dilurate (DBTDL) as a catalyst. The polymerization reaction gave similar results in the presence or absence of DBTDL, indicating that, the catalyst was not needed in this process. Various polyureas were obtained with high yields and moderate inherent viscosities ranging from 0.26 to 0.38 dL/g. This method was compared with the polymerization reaction in conventional solvent and in the presence of DBTDL as a catalyst. In the case of using TBAB, higher yields and inherent viscosities were obtained. This process was safe and green since toxic and volatile solvent such as N,N-dimethylacetamide (DMAc) was eliminated.     

Novel silver/polyurethane nanocomposite by in situ reduction: Effects of the silver nanoparticles on phase and viscoelastic behavior

A novel silver/poly(carbonate urethane) nanocomposite was prepared through in situ reduction of a silver salt (AgNO₃) added to a solution consisting of a commercial poly(carbonate urethane) dissolved in N,N‐dimethylformamide (DMF). In this system, the presence of the poly(carbonate urethane) was proved to protect the silver nanoparticles, whose formation was confirmed by means of UV–vis spectroscopy, from aggregation phenomena. The silver morphology developed in the solid state after DMF casting was imaged by FESEM. Homogeneous dispersion of silver nanoprisms in the poly(carbonate urethane) matrix was clearly observed. The effects of dispersion of silver nanoparticles within the poly(carbonate urethane) matrix were investigated by means of ATR‐FTIR and multifrequency dynamic mechanical thermal analyses. The obtained results revealed that the presence of silver nanoparticles modifies both the phase and the viscoelastic behaviors of poly(carbonate urethane). As a matter of fact, the hydrogen bond formation in the hard and soft segments was found to be hindered and the molecular motions of the soft segments were restricted, because a comparatively higher activation energy was required for the related α‐relaxation process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 344–350, 2008     

In Situ FT-IR Studies of the Zirconium (IV) Acetylacetonate Catalyzed Urethane Reaction of Butanediols

A comparative kinetic study of the urethane reactions of phenyl isocyanate and 1,2-, 1,3-, and 1,4-butanediol was carried out in dichloromethane solution with zirconium (IV) acetylacetonate as catalyst. In situ FT-IR was used to follow the kinetics of the reactions at a constant temperature of 15°–30°C. The rate constants for the reaction of the primary hydroxyl group and the secondary hydroxyl group were calculated as k _prim and k _sec, respectively. Analysis of the second-order rate constants of these systems indicated that k _prim follows 1,2-butanediol >1,3-butanediol >1,4-butanediol. The ratio of k _prim/k _sec in 1,2-butanediol was the highest and the order followed was the same as with the reaction rate. Activation energies and Eyring parameters were also determined for the urethane reaction of butanediols.     

Ferric Acetylacetonate Catalyst on the Urethane Reaction of Phenyl Isocyanate and 1,2-Propyleneglycol: A Study of Kinetics,Thermodynamics, and Mechanism with In Situ FT-IR Spectroscopy

The urethane reaction of phenyl isocyanate and 1,2-propylene glycol was investigated with ferric acetylacetonate (Fe(acac)₃) as catalyst. The effect of the catalytic properties of Fe(acac)₃ on the formation of the urethane bond was evaluated with in situ FT-IR. The influence of the Fe(acac)₃ concentration as well as the reaction temperature is discussed. It was observed that there was a turning point in the reaction rate when the temperature decreases, which remained unchanged with variation in Fe(acac)₃ concentration. Arrhenius and Eyring parameters of the primary hydroxyl group were determined for the catalyzed reaction. The low-temperature and high-temperature values are surprisingly different. A reasonable reaction mechanism is proposed and the possible active species are discussed, followed by a kinetics and thermodynamics discussion.     

Synthesis and photopolymerization kinetics of multifunctional aromatic urethane acrylates containing tertiary amine group

Two multifunctional aromatic urethane acrylates, based on 2, 4‐toluene diisocyanate (2, 4‐TDI), β‐hydroxyethyl arcylate (HEA), and synthetic multifunctional hydroxyl compounds, were synthesized by classical condensation reaction. FTIR was used to monitor the process of the reaction. The photopolymerization kinetics of the urethane acrylates with different photoinitiators was studied by Real‐Time Infrared Spectroscopy. The results indicated that different from the commercial urethane acrylate CN 975, the synthetic multifunctional urethane acrylates could be efficiently initiated by BP without the addition of any co‐initiators as they have tertiary amine structures. Copyright © 2008 John Wiley & Sons, Ltd.     

Catalytic Kinetics and Mechanism Transformation of Fe(acac)3 on the Urethane Reaction of 1,2‐Propanediol with Phenyl Isocyanate

The urethane reaction of 1,2‐propanediol with phenyl isocyanate was investigated with ferric acetylacetonate (Fe(acac)₃) as a catalyst. In situ Fourier transform infrared spectroscopy was used to monitor the reaction, and catalytic kinetics of Fe(acac)₃ was studied. The reaction rates of both hydroxyl groups were described with a second‐order equation, from which the influence of the Fe(acac)₃ concentration and reaction temperature was discussed. It was very surprising that the relationship between 1/C and t became constant when reaction temperature increased, which indicated that there was no reactive distinction between the two hydroxyl groups. Although the phenomenon differed with the variation of temperature, it was unaffected by the Fe(acac)₃ concentration. It was attributed to the transformation of the reaction mechanism with the increase in temperature. Furthermore, activation energy (E_a), enthalpy (ΔH*), and entropy (ΔS*) for the catalyzed reaction were determined from Arrhenius and Eyring equations, which testified to the transformation of the reaction mechanism.