Surface modification of hydroxyapatite with poly(methyl methacrylate) via surface-initiated ATRP

This article describes the fabrication of hydroxyapatite (HAP) nanocomposites grafted with poly(methyl methacrylate) (PMMA). Surface-initiated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was carried out from hydroxyapatite particles derivatized with ATRP initiators. The structure and properties of the nanocomposites were investigated by thermogravimetric analysis (TGA), transmission electron microscopy (TEM), differential scanning calorimeter (DSC) measurements, and contact angle analyses. TGA was used to estimate the grafting density of ATRP initiators (0.49 initiator/nm²) and the amount of grafted PMMA on the HAP surface. The contact angle analyses indicated that grafting PMMA onto the HAP surface dramatically increased the hydrophobicity of the surface. Moreover, the HAP nanocomposites showed excellent dispersibility in both aqueous solution and organic solvent.     

Morphology and properties of poly(methyl methacrylate)/clay nanocomposites by in-situ solution polymerization

Poly(methyl metacrylate)/montmorillonite (PMMA)/(MMT) nanocomposites were prepared by in-situ solution polymerization of methyl methacrylate monomer in the presence of the organic modified MMT-clay. After the organic modification by ionic exchanging with amine salts, the organoclay becomes more hydrophobic and compatible then pristine clay with methyl methacrylate monomer. The modified clays are characterized by wide angle X-ray diffraction (WAXRD). The powdered X-ray diffraction and transmission electron microscopy (TEM) techniques were employed to study the morphology of the PMMA/clay nanocomposites which indicate that the modified clays are dispersed in PMMA matrix to form both exfoliated and intercalated PMMA/modified clay nanocomposites. The thermo-mechanical properties were measured by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC). Gas permeability analyzer (GPA) shows the excellent gas barrier property of the PMMA nanocomposites which is in good agreement with the morphology. The optical property was measured by UV-vis spectroscopy which shows that these materials have good optical clarity, and UV resistance.     

Surface modification of magnesium aluminum hydroxide nanoparticles with poly(methyl methacrylate) via one-pot in situ polymerization

Hydrophobic magnesium aluminum hydroxide composite particles (PMMA-MAH) were obtained by means of grafting poly(methyl methacrylate) (PMMA) onto the surface of magnesium aluminum hydroxide(MAH) nanoparticles after a novel type of phosphate coupling agent (DN-27) modification. The introduction of functional double bonds was firstly conducted on the surface of nanoparticles by DN-27 modification, followed by one-pot in situ polymerization on the particles surface using methyl methacrylate (MMA) as monomer, azoisobutyronitrile (AIBN) as initiator and sodium dodecyl sulfate (SDS) as stabilizer to graft PMMA on the surface of DN-27-modified MAH particles. The obtained composite particles were characterized by field-emission scanning electron microscope (FESEM), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), X-ray powder diffraction (XRD). The results show that the organic macromolecule PMMA could be successfully grafted on the surface of DN-27-modified MAH nanoparticles and the thermal stability of the PMMA-MAH composite particles had been improved. Compared with unmodified blank MAH sample, the product obtained with this method possesses better hydrophobic properties such as a higher water contact angle of 108° and a well dispersion.     

Clay dispersion and physical properties of melt-blended PP/organoclay nanocomposites: effect of interfacial interaction

Melt blending of maleic anhydride-grafted polypropylene (PPgMA) and organically modified clay nanocomposites was first carried out in a plasticorder. The structure was investigated with x-ray diffraction (XRD) and transmission electron microscopy (TEM). The interfacial interaction between PB3150 compatibilizer and I30 clay surface was altered with the addition of different loadings of PB3150. It was found at the PB3150 compatiblizer gave rise to a high degree of clay dispersion beyond the PB3150/I30 weight ratio of 3. We then also modified polypropylene/organoclay nanocomposites with different loadings of PB3150 on a twin-screw extruder. When the PB3150 loading exceeded 15 wt%, extensive exfoliation of clay was observed. The relative complex viscosity curves also revealed a systematic trend with the extent of exfoliation and showed promise for quantifying the hybrid structure of the nanocomposites. Mechanical properties and thermal stability were determined by tensile and impact tests and thermogravimeric analysis (TGA), respectively. Although high loading of PB3150 leads to better clay dispersion in the polypropylene nanocomposites, it causes deterioration in both mechanical and thermal properties of the hybrid systems.     

Enhancement of thermal and mechanical properties of poly(MMA-co-BA)/Cloisite 30B nanocomposites by ultrasound-assisted in-situ emulsion polymerization

This study reports synthesis and characterization of poly(MMA-co-BA)/Cloisite 30B (organo-modified montmorillonite clay) nanocomposites by ultrasound-assisted in-situ emulsion polymerization. Copolymers have been synthesized with MMA:BA monomer ratio of 4:1, and varying clay loading (1–5 wt% monomer). The poly(MMA-co-BA)/Cloisite 30B nanocomposites have been characterized for their thermal and mechanical properties. Ultrasonically synthesized nanocomposites have been revealed to possess higher thermal degradation resistance and mechanical strength than the nanocomposites synthesized using conventional techniques. These properties, however, show an optimum (or maxima) with clay loading. The maximum values of thermal and mechanical properties of the nanocomposites with optimum clay loading are as follows. Thermal degradation temperatures: T_10% = 320 °C (4 wt%), T₅₀ = 373 °C (4 wt%), maximum degradation temperature = 384 °C (4 wt%); glass transition temperature = 64.8 °C (4 wt%); tensile strength = 20 MPa (2 wt%), Young’s modulus = 1.31 GPa (2 wt%), Percentage elongation = 17.5% (1 wt%). Enhanced properties of poly(MMA-co-BA)/Cloisite 30B nanocomposites are attributed to effective exfoliation and dispersion of clay nanoparticles in copolymer matrix due to intense micro-convection induced by ultrasound and cavitation. Clay platelets help in effective heat absorption with maximum surface interaction/adhesion that results in increased thermal resistivity of nanocomposites. Hindered motion of the copolymer chains due to clay platelets results in enhancement of tensile strength and Young’s modulus of nanocomposite. Rheological (liquid) study of the nanocomposites reveals that nanocomposites have higher yield stress and infinite shear viscosity than neat copolymer. Nonetheless, nanocomposites still display shear thinning behavior – which is typical of the neat copolymer.     

Mechanical and Thermal Properties of Poly(Tetrahydrofurfuryl Methacrylate) Nano-Composites

To obviate the brittleness and improve the mechanical properties of poly(tetrahydrofurfuryl methacrylate) (PTHFMA), clay mineral nano-composites of PTHFMA with two different montmorillonites (MMT), Cloisite® 20A and Cloisite® 30B, were prepared. The mechanical properties were investigated by dynamic mechanical analysis (DMA) and nanoindentation. The thermal properties of the nano-composites were studied using thermogravimetric analysis (TGA). According to the DMA results, tanδ was increased by addition of the clay, leading to the improvement in the mechanical properties which was also confirmed by the nanoindentation results. TGA thermograms showed better thermal stability for the nano-composites compared to that of the homopolymer. Considering all results, the clay mineral polymer nano-composites (CPN) with Cloisite® 20A exhibited better properties compared to those with Cloisite® 30B. Transmission electron microscopy (TEM) micrographs, and X-ray diffraction (XRD) patterns validated intercalation-exfoliation of the clay mineral layers for the Cloisite 20A and intercalation of the Cloisite 30B in the polymer matrix.     

Preparation and characterization of biodegradable aliphatic polyester/thermoplastic starch/organoclay ternary hybrid nanocomposites

Biodegradable aliphatic polyester (APES)/thermoplastic starch (TPS)/Cloisite 30B ternary hybrid nanocomposites were prepared via melt intercalation. The dispersion of the silicate layers in the APES/TPS hybrids were characterized by using X-ray diffraction and transmission electron microscopy. Tensile and barrier properties of the APES/TPS/Cloisite 30B hybrids were also studied. Adding APES to the TPS/Cloisite 30B hybrids leads to higher tensile strength and improved barrier property.     

Dielectric Probing of Relaxation Behaviors in PMMA/Organoclay Nanocomposites: Effect of Organic Modification

Poly(methyl methacrylate) (PMMA)–clay nanocomposites (PCN) were prepared with PMMA/clay concentrates and POP-diamines modified clay via melt blending. Partially exfoliated clay layers were uniformly dispersed in the nanocomposites as evidenced from XRD study. The subglassβ relaxation and the segmental α relaxation were observed from the dynamic mechanical thermal analysis (DMTA). The PCNs at 5 wt% clay level from clay concentrate exhibited significantly higher glass-transition temperatures and dynamic storage moduli relative to the neat PMMA. The confinement effect from the tethering of polymer chain to the clay surface would contribute to such a dramatic difference. In addition to the normal-mode relaxations, the αβ-merging process above T _g and the subglass interfacial polarization were detected from the dielectric analysis. Significant increase in dielectric permittivities and dielectric losses due to interfacial polarization and ionic conduction at low frequency were observed for the PCNs. The intensity of the interfacial polarization process increases with the dispersion degree of clay layers and hence the process can be assigned to the space charge polarization of the ionic species in the clay intergalleries.     

Carboxylated acrylo nitrile butadiene rubber latex/kaolin nanocomposites: preparation and properties

Carboxylated nitrile butadiene rubber (XNBR)–based nanocomposites with varying amounts of nanokaolin were produced by latex stage mixing. Sonication of the unmodified kaolin and the technique adopted for the preparation of the composite have helped to get a uniform dispersion of clay in XNBR matrix. Nanokaolin caused enhancement in the mechanical properties of the composites. Proper dispersion of the clay particles, partial exfoliation/intercalation of clay, and interaction of clay with the polar rubber latex made nanokaolin good reinforcing filler in XNBR latex. Swelling studies conducted in methyl ethyl ketone showed a decrease in the swelling index and solvent uptake confirming the hindrance exerted by clay and the possible clay–rubber interaction. Increase in complex modulus obtained from the strain sweep analysis is a further evidence for better rubber filler interaction. The composites were characterized by the scanning electron microscopy, X-ray diffraction analysis, and atomic force microscopy.     

Influence of Compatibilizer-Type and Processing Approach on the Dispersion of OMMT in High-Density Polyethylene Matrix

High-density polyethylene/organoclay nanocomposites were prepared via melt intercalation in an internal mixer using both a direct mixing and master batching method. Two types of maleic anhydride grafted polyethylene, high-density polyethylene grafted maleic anhydride, and linear low-density polyethylene grafted maleic anhydride, (HDPE-g-MA, LLDPE-g-MA) were used as compatibilizers to enhance the dispersibility of nanoclay in HDPE. Dispersion of organoclay in the nanocomposites was characterized by using X-ray diffraction (XRD), transmission electron microscopy (TEM), and rheological mechanical spectroscopy (RMS). Effects of clay content and degree of clay dispersion on the rheological and tensile properties were also investigated. Furthermore, the effect of order of mixing on the dispersion and distribution of the clay layers was studied. The obtained results showed that organoclay in the nanocomposites were dispersed homogeneously and exfoliated better when HDPE-g-MA and the direct mixing route were used. Although in the master batching method clay intercalated better, clay layers chiefly remain in compatibilizer rich areas. On the other hand, direct mixing was observed to lead to clay particles being dispersed in the HDPE matrix or at the interface of the matrix and compatibilizer and, consequently, better improvement in the tensile modulus was achieved. It was determined that the compatibilizer with the higher miscibility with the matrix was the key factor for achieving better exfoliation of clay sheets.     

Surface modification and characterization of magnesium hydroxide sulfate hydrate nanowhiskers

In order to enhance the compatibility with plastic polymers, magnesium hydroxide sulfate hydrate (MHSH) nanowhiskers were modified through grafting methyl methacrylate (MMA) on the surface of the nanowhiskers by emulsion polymerization. The influences of the reaction time, MMA monomer content, adding speed of monomer and the reaction temperature on the grafting ratio were investigated. Thermogravimetry (TG), Fourier transform infrared (FT-IR) spectroscopy, X-ray powder diffraction (XRD), scanning electron microscope (SEM), energy-dispersive X-ray (EDX) spectroscopy and surface contact angle measurement were used to characterize the effect of surface modification. The results showed that the MHSH nanowhiskers were uniformly coated by polymethyl methacrylate (PMMA), and a well-defined core-shell hybrid structure of MHSH/PMMA was obtained. The surface contact angle of the hybrid whiskers increased to 87.32° from 12.71° and the whiskers surface was changed from hydrophilic to lipophilic.     

纳米ZnO的表面化学修饰及其分析表征

采用水溶性羟丙基甲基纤维素HPMC对无机纳米ZnO粒子进行物理吸附处理 ,获得了核为无机纳米ZnO ,外壳为水溶性高分子HPMC的粒子。然后在其上进行了甲基丙烯酸甲酯的接枝聚合。采用红外光谱、差热分析的方法对复合粒子进行了表征 ,并采用透射电镜观察了粒子的形貌。红外光谱表明在纳米ZnO的表面吸附了HPMC并接枝了PMMA ,差热分析表明HPMC ,HPMC g PMMA和ZnO/HPMC g PMMA的热稳定性逐渐提高 ,透射电镜观察表明 ,在纳米ZnO的表面粘附了一层聚合物 ,成功地实现了纳米粒子的表面修饰。     

Effect of Nanoclay on the Morphology and Properties of Nylon 6 and Poly(Methyl Methacrylate) (PMMA) Blends

The effect of organomodified nanoclay on the morphology and properties of a (70/30 w/w) nylon 6/poly(methyl methacrylate) (PMMA) blend prepared by a melt processing method was investigated. The number average domain diameter (D_n ) of the dispersed PMMA phase was found to decrease with the addition of a small amount [0.5 per hundred resin (phr)] of clay in the blend. A much finer dispersion of the minor phase in the presence of a higher amount (5 phr) of clay indicated better mixing efficiency and improved morphology in the blend. X-ray diffraction indicated the exfoliation of the clays in the nylon 6 matrix, whereas PMMA chains only intercalated into the clay layers. However, the same effect of the clay was not observed in a (30/70 w/w) nylon 6/PMMA blend when nylon 6 became the dispersed domains. In the (30/70 w/w) nylon 6/PMMA blend, the addition of organomodified nanoclay (up to 2 phr) increased the D_n of the nylon 6 domains by preferential location of the clays inside the nylon 6 domains. Addition of styrene-maleic anhydride (SMA) copolymer effectively reduced the D_n of disperse phases in both compositions of the nylon 6/PMMA blends. Thus, in nylon 6/PMMA blends, clay platelets could prevent the coalescence of dispersed domains during melt mixing as long as it was dispersed in the matrix phase of the blend. Mechanical properties and thermal stability of the blends were also improved in the presence of clay.     

Radiation graft copolymerization of butyl methacrylate and acrylamide onto low density polyethylene and polypropylene films,and its application in wastewater treatment

Butyl methacrylate and acrylamide (BMA/AAm) comonomers were grafted onto low-density polyethylene (LDPE) and polypropylene (PP) films using the mutual gamma radiation grafting technique. The influences of grafting conditions such as solvent, monomer concentration, monomer composition, and irradiation dose on the grafting yield were determined. It was found that using dimethyl formamide as a solvent enhanced the copolymerization process. The grafting yield increases as the comonomer concentration increases up to 60%. Also it was found that the degree of grafting of BMA/AAm onto both LDPE and PP films increases as the AAm content increases till an optimum value at 50:50 wt%. The grafting yield of the comonomers was found to increase with increase in the radiation dose. It was observed that the degree of grafting of polyethylene films is higher than that of polypropylene (PP) films at the same conditions. Some selected properties of the graft copolymers, such as water uptake and thermal properties, were determined using thermogravimetric analysis. The morphology and structure of the grafted films were investigated using scanning electron microscopy, infra-red, and X-ray diffraction. Improvement in such properties of the prepared copolymers was observed which offers possible uses in some practical applications such as the removal of some heavy metals from wastewater. It was found that the maximum metal uptake by the copolymer followed the order Cu²⁺>Co²⁺>Ni²⁺ ions.     

Morphology,miscibility and mechanical properties of PMMA/PC blends

This study deals with some results on morphology, miscibility and mechanical properties for polymethyl methacrylate/polycarbonate (PMMA/PC) polymer blends prepared by solution casting method at different concentration between 0 and 100 wt%. Dynamic storage modulus and tan δ were measured in a temperature range from 30 to 180°C using dynamical mechanical analyzer (DMA). The value of the storage modulus was found to increase with the addition of the PC in the matrix. Transition temperature of pure PMMA and pure PC is found to be 83.8 and 150°C, respectively. The result shows that the two polymers are miscible for whole concentration of PC in PMMA. The distribution of the phases in the blends was studied through scanning electron microscopy (SEM). Also the mechanical properties like elongation at break and fracture energy of the PMMA/PC blends increase with the increase in concentration of PC in PMMA.     

Glass Transition Behavior and Dynamic Fragility of PMMA-SAN Miscible Blend-Clay Nanocomposites

An investigation of the segmental dynamics and glass transition behavior of a miscible polymer blend composed of poly(methyl methacrylate) (PMMA) and poly(styrene-ran-acrylonitrile) (SAN) and its melt intercalated nanocomposite by dynamic mechanical analysis is presented. The principle goal was to address the effect of intercalation on local molecular structure and dynamics. The results showed that the intercalation of polymer chains in the galleries of organoclay (Cloisite 30B) led to a lower temperature dependence of the relaxation time (fragility) and activation energy of α-relaxation. Moreover, calculation of the distribution of the segmental dispersion showed a narrower dispersion in the glass transition region so that the Kohlrausch-Williams-Watts (KWW) distribution parameter (β_KWW) increased from 0.21 for neat PMMA to 0.34 for the 50/50 PMMA/SAN blend nanocomposite containing 3 wt% organoclay. Furthermore, the relaxation behavior of the blends showed a negative deviation from mixture law predictions based on the responses of the neat PMMA and SAN. These behaviors were attributed to the lack of specific interactions between the blend components (PMMA, SAN, and nanoclay layers) and the less cooperative behavior, i.e., less constraint for segmental relaxation, of the intercalated chains.     

Graft Polymerization of Methyl Methacrylate- Acrylonitrile onto Poly(ethene-co-1-butene) and Its Toughening Effect on SAN Resin

Poly(ethene-co-1-butene)-graft-methyl methacrylate-acrylonitrile (PEB-g-MAN) was prepared by suspension grafting copolymerization of methyl methacrylate (MMA) and acrylonitrile(AN) onto PEB. PEB-g-MAN/SAN resin blends (ABMS) were prepared by blending PEB-g-MAN with styrene-acrylonitrile copolymer (SAN resin). The effects of AN/(MMA+AN) feed ratio (f_AN), PEB/(PEB+MMA+AN) feed ratio (f_PEB) and benzoyl peroxide (BPO) dosage on the monomer conversion ratio (CR), rubber's grafting ratio (GR), grafting efficiency (GE) of the copolymerization and the toughening effect of PEB-g-MAN on the SAN resin were investigated. FTIR quantitative analysis showed that when the weight percent of AN unit in the unextracted product was 21.5 wt% with f_AN of 25 wt%, the toughening effect of unextracted PEB-g-MAN on SAN resin was the highest. Gel permeation chromatography (GPC) analysis showed that when f_AN was 25 wt%, the grafted copolymer had the lowest molecular weight and ABMS had highest toughness. Transmission electron microscopy (TEM) analysis showed that the highest toughness occurred when the phase structure of ABMS was cocontinuous with f_AN of 25 wt%. When f_AN was 25 wt% PEB-g-MAN domains have numerous small SAN domains in them, which was occlusion structure. Scanning electron microscopy (SEM) analysis indicated that the ABMS fracture surfaces had plastic flow visible, which looked like a craze fibers morphology, for the sample with highest impact strength (f_AN = 25 wt%). Dynamic mechanical thermal analysis (DMA) showed that the miscibility of the PEB phase and SAN phase improved after graft copolymerization of MMA and AN onto PEB.     

Effect of clay silylation on curing and mechanical and thermal properties of unsaturated polyester/montmorillonite nanocomposites

This work focuses on the chemical modification of montmorillonite (MMT) (Cloisite® Na) with compatible silanes, vinyltriethoxysilane (CVTES) and γ-methacryloxypropyltrimethoxysilane (CMPS) in order to prevent agglomeration and to improve montmorillonite interaction with an unsaturated polyester resin matrix seeking to achieve a multifunctional composite. Clays were dispersed in the resin by mechanical stirring and sonication and the nanocomposites were prepared by resin transfer into a mold. The mechanical, morphological, thermal and flammability properties of the obtained composites were compared with those prepared using commercial Cloisite® 30B (C30B) and Cloisite® 15A (C15A) clays. Advantages of using silane-modified clays (CVTES and CMPS) as compared with organic-modified clays (C30B and C15A) can be summarized as similar flexural strength and linear burning rate but higher storage modulus and improved adhesion to the polyester resin with consequent higher thermal deflection temperature and reinforcement effectiveness at higher temperatures. However, organic modified clays showed better dispersion (tendency to exfoliate) and consequently delayed thermal volatilization due to the clay barrier effect.     

Chemically induced graft copolymerization of 2-hydroxyethyl methacrylate onto polyurethane surface for improving blood compatibility

To improve hydrophilicity and blood compatibility properties of polyurethane (PU) film, we chemically induced graft copolymerization of 2-hydroxyethyl methacrylate (HEMA) onto the surface of polyurethane film using benzoyl peroxide as an initiator. The effects of grafting temperature, grafting time, monomer and initiator concentrations on the grafting yields were studied. The maximum grafting yield value was obtained 0.0275 g/cm² for HEMA. Characterization of the films was carried out by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), water contact angle measurements. ATR-FTIR data showed that HEMA was successfully grafted onto the PU films surface. Water contact angle measurement demonstrated the grafted films possessed a relatively hydrophilic surface. The blood compatibility of the grafted films was preliminarily evaluated by a platelet-rich plasma adhesion test and hemolysis test. The results of platelet adhesion experiment showed that polyurethane grafted polymerization with monomer of 2-hydroxyethyl methacrylate had good blood compatibility featured by the low platelet adhesion. Hemolysis rate of the PU-g-PHEMA films was dramatically decreased than the ungrafted PU films. This kind of new biomaterials grafted with HEMA monomers might have a potential usage for biomedical applications.     

Preparation of PMMA grafted aluminum powder by surface-initiated in situ polymerization

Poly(methyl methacrylate) (PMMA) grafted aluminum powder was successfully prepared by surface-initiated in situ polymerization. The process was divided into two steps: adsorption of initiator and polymerization of monomer. It was found that the driving force of adsorption between initiator and aluminum was due to electrostatic force, not chemical bonding, and the percentage of adsorption (PA) and adsorption efficiency (AE) would reach as high as 31.2% and 52.0%, respectively. As for the process of in situ polymerization, the conversion of monomer (C), percentage of grafting (PG) and grafting efficiency (GE) were investigated by evolved hydrogen detection. It was shown that the PG and GE obtained were consistent with those calculated through TGA analysis.