高盐油藏下两性/阴离子表面活性剂协同获得油水超低界面张力

研究了在高盐油藏中, 利用两性/阴离子表面活性剂的协同效应获得油水超低界面张力的方法. 两性表面活性剂十六烷基磺基甜菜碱与高盐矿化水具有很好的相容性, 但在表面活性剂浓度为0.07%-0.39%(质量分数)范围内仅能使油水界面张力达到10^-2 mN·m^-1量级, 加入阴离子表面活性剂十二烷基硫酸钠后则可与原油达到超低界面张力. 通过探讨表面活性剂总浓度、金属离子浓度、复配比例对油水动态界面张力的影响, 发现两性/阴离子表面活性剂混合体系可以在高矿化度、低浓度和0.04%-0.37%的宽浓度范围下获得10^-5 mN·m^-1量级的超低界面张力, 并分析了两性/阴离子表面活性剂间协同获得超低界面张力的机制.     

Research and application of ultralow interfacial tension oil displacement agent

An ultralow interfacial tension (IFT) oil displacement agent, which was a surfactant combinational system (HCS) with good salt and heat resistance, was synthesized using amphoteric betaine (AMS)/anionic sulfonate (AKS)/nonionic alkyl amide (NIS). The interface tensiometer was used to test the IFT. The results showed that the oil–water IFT could be as low as 10^?4 mN/m when the salinity is 10,000～50,000?mg/L, the concentration is 1～5?g/L, and the temperature is 40～80°C. The surfactant system has good emulsification stability. The displacement simulation experiments demonstrated that the increment of the recovery ratio can be up to 14.1%. The surfactant system could meet the demands of site operation.     

Synthesis and properties of nonylphenol-substituted dodecyl sulfonate

Nonylphenol-substituted dodecyl sulfonate (C₁₂-NPAS) was synthesized via sulfonation-alkylation-neutralization using 1-dodecene, SO₃, and nonylphenol as raw materials. The properties such as surface tension, interfacial tension (IFT), wettability, foam properties, and salinity tolerance of C₁₂-NPAS were systematically investigated. The results show that the critical micelle concentration (CMC) of C₁₂-NPAS was 0.22?mmol?·?L^?1 and the surface tension at the CMC (γ_CMC) of C₁₂-NPAS was 29.4 mN/m. When compared with the traditional surfactants sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate (SDS), and linear alkylbenzene sulfonate (LAS), the surface properties of C₁₂-NPAS were found to be superior. The IFT between Daqing crude oil and a weak-base alkaline/surfactant/polymer (ASP) oil flooding system containing 0.1?wt% of C₁₂-NPAS can reach an ultralow level of 2.79?×?10^?3 mN/m, which was lower than that found for the traditional surfactant heavy alkylbenzene sulfonate (HABS). The salinity and hardness tolerance of C₁₂-NPAS were much stronger than those found for conventional surfactants, petroleum sulfonate, and LAS. C₁₂-NPAS also shows improved wetting performance, foamability, and foam stability.     

Synthesis and Performance of Novel Sulfonate Gemini Surfactant with Trialkyl Chains

A new type of sulfonate gemini surfactant with three lipophilic alkyl chains (3C₁₀-DS) was synthesized, and the structure of the product was confirmed by using the infrared spectrum and mass spectrum. Its critical micelle concentration (CMC) is 0.41 mmol/L, one order of magnitude lower than those of convectional (single-chain) surfactants, and the minimum surface tension is 27.6 mN/m. The interfacial tension (IFT) between the compound system of 3C₁₀-DS and petroleum sulfonate (PS) and the simulated oil reaches ultra-low levels (10^?3 mN/m), and there exists significant synergistic effect between 3C₁₀-DS and PS. The compound flooding system consisting of polymer and the mixture of 3C₁₀-DS and PS can effectively improve oil recovery for high-medium permeability cores and have a good application prospect in enhancing oil recovery.     

Interfacial Properties,Wettability Alteration and Emulsification Properties of an Organic Alkali–Surface Active Ionic Liquid System: Implications for Enhanced Oil Recovery

Combinatory flooding techniques evolved over the years to mitigate various limitations associated with unitary flooding techniques and to enhance their performance as well. This study investigates the potential of a combination of 1-hexadecyl-3-methyl imidazolium bromide (C₁₆mimBr) and monoethanolamine (ETA) as an alkali–surfactant (AS) formulation for enhanced oil recovery. The study is conducted comparative to a conventional combination of cetyltrimethylammonium bromide (CTAB) and sodium metaborate (NaBO₂). The study confirmed that C₁₆mimBr and CTAB have similar aggregation behaviors and surface activities. The ETA–C₁₆mimBr system proved to be compatible with brine containing an appreciable concentration of divalent cations. Studies on interfacial properties showed that the ETA–C₁₆mimBr system exhibited an improved IFT reduction capability better than the NaBO₂–CTAB system, attaining an ultra-low IFT of 7.6 × 10⁻³ mN/m. The IFT reduction performance of the ETA–C₁₆mimBr system was improved in the presence of salt, attaining an ultra-low IFT of 2.3 × 10⁻³ mN/m. The system also maintained an ultra-low IFT even in high salinity conditions of 15 wt% NaCl concentration. Synergism was evident for the ETA–C₁₆mimBr system also in altering the carbonate rock surface, while the wetting power of CTAB was not improved by the addition of NaBO₂. Both the ETA–C₁₆mimBr and NaBO₂–CTAB systems proved to form stable emulsions even at elevated temperatures. This study, therefore, reveals that a combination of surface-active ionic liquid and organic alkali has excellent potential in enhancing the oil recovery in carbonate reservoirs at high salinity, high-temperature conditions in carbonate formations.     

Foam Flooding with Ultra-Low Interfacial Tension to Enhance Heavy Oil Recovery

Severe viscous fingering during water flooding of heavy oil leaves a large amount of oil untouched in the reservoir. Improving sweep efficiency is vital for increasing heavy oil recovery. Previous researches have proved that foam flooding can increase the sweep efficiency and oil recovery. The polymers could make the foam more stable and have better plugging capacity, but the interfacial tension (IFT) of oil and water increase which could decrease the displacement efficiency of the heavy oil. In view of the deficiency of conventional foam flooding, it is necessary to research the ultra-low interfacial tension foam which could improve macro-swept volume and micro-displacement efficiency in heavy oil reservoir. In this paper a novel foam agent is developed by the combination of surfactant and additives to lower the IFT of oil and water. The operating parameters including foam injections modes and gas liquid ratio were investigated by core flooding experiments. Field test performance shows that oil production per day increased from 85.6 to 125.7 t, water cut declined from 92.1 to 83.6% after 3 months injection. This study provides a novel method to improve heavy oil recovery with an ultra-low interfacial tension foam flooding system.     

The Wettability Alteration and the Effect of Initial Rock Wettability on Oil Recovery in Surfactant-based Enhanced Oil Recovery Processes

Wettablity alteration of rock surface is an important mechanism for surfactant-based enhanced oil recovery (EOR) processes. Two salt and temperature-tolerant surfactant formulations were developed based on the conditions of high temperature (97–120°C) and high salinity (20 × 10⁴ mg/L) reservoirs where a surfactant-based EOR process is attempted. Both the two sufactant formulations can achieve ultralow interfacial tension level (≤10^?3 mN/m) with crude oil after aging for 125 days at reservoir conditions. Wettability alteration of core slices induced by the two surfactant formulations was evalutated by measuring contact angles. Core flooding experiments were carried out to study the influence of initial rock wettabilities on oil recovery in the crude oil/surfactant/formation water/rock system. The results indicated that the two formulations could turn oil-wet core slices into water-wet at 90–120°C and 20 × 10⁴ mg/L salinity, while the water-wet core slices retained their hydrophilic nature. The core flooding experiments showed that the water-wet cores could yield higher oil recovery compared with the oil-wet cores in water flooding, surfactant, and subsequent water flooding process. The two surfactant formulations could successfully yield additional oil recovery in both oil-wet and water-wet cores.     

Studies of Interfacial Activities of Four Kinds of Surfactants at Oil/Water Interface

This article aims to compare the interfacial activities of different kinds of surfactants in the same oil/water system. The anionic surfactants of alkylbenzene sulfonates, the polyoxyethylenated nonionic surfactants, the cationic surfactants of alkyl trimethyl ammonium chlorides, and the zwitterionic surfactants of alkyl hydroxyl sulfobetaines were used, and the interfacial tensions of the surfactant solutions against kerosene at different NaCl concentrations were measured. It is found that the interfacial activities of the alkylbenzene sulfonates are high and ultralow interfacial tensions (<0.01 mN/m) can be obtained at proper salinities. While, the nonionic surfactants have relatively low interfacial activities and the minimum tensions are around 0.01 mN/ms. The salinity scanning curves of the alkylbenzene sulfonates and nonionic surfactants decrease first, then increase, showing their interfacial activities can be changed by the salinity effectively. The cationic and zwitterionic surfactants have very low interfacial activities, of which all the tensions are higher than 0.1 mN/ms and are hard to be changed by the salinity. The experimental results may have important reference values for enhanced oil recovery.     

CO2 Mobility and CO2/Brine Interfacial Tension Reduction by Using a New Surfactant for EOR Applications

The synthesis and use in enhanced oil recovery applications of a novel CO₂-philic surfactant derived from maleic anhydride and 2-butyl-1-octanol is reported. The synthesis involved the esterification of maleic anhydride to produce diester followed by sulfonation of the esterified product. The esterification reaction parameters were optimized for the maximum yield of 98.4%. By employing a silica sulfuric acid catalyst, the reaction kinetics of esterification were also investigated. The activation energy was found to be 45.58 kJ/mol. The sulfonation reaction of the esterified product was performed by using sodium bisulfite, and a yield of 82% of surfactant was achieved. The synthesized surfactant lowered the interfacial tension between CO₂/brine to 3.1 mN/m and effectively reduced the CO₂ mobility. This surfactant has a great potential to be used for CO₂ mobility control for CO₂?EOR applications.      

Synthesis and Interfacial Activity of Nonyl Phenol Polyoxyethylene Ether Carboxylate

In order to study the interfacial activity of the anionic-nonionic surfactant, five nonyl phenol polyoxyethylene ether carboxylates were synthesized and mass spectra were used to characterize their structures. The tensions of the anionic–nonionic surfactant aqueous solutions against crude oil were measured and the effects of the surfactant structure, concentration, and salinity on the interfacial activities were discussed. It was shown that nonyl phenol polyoxyethylene (6) ether carboxylate can produce ultralow interfacial tension when the concentrations are not lower than 0.10%, exhibiting a high interfacial activity and a good anti-dilution resistance. Moreover, it was proved that there exists synergism between NaCl and MgCl₂ (or CaCl₂), which is crucial to achieve the ultralow interfacial tension.     

Synthesis and surface active properties of a gemini-type surfactant linked by a quaternary ammonium group

In this study, cationic surfactants having multi-hydroxyl groups were synthesized by the condensation reaction of octadec-9-enyl glycidyl ether and methyl amine followed by the quaternization with dimethyl sulfate. The structure of the product was elucidated by ¹H-NMR and FT-IR. The minimum critical micelle concentration (CMC) and surface tension achieved using C18:1-BHDM surfactant were 1.24?×?10^?4?mol/L and 43.36 mN/m, respectively. The interfacial tensions measured between 1 wt% surfactant solution and n-decane were found to be in the same order of magnitude as those exhibited between micellar solutions and nonpolar hydrocarbon oils. The contact angle measurement result suggests that C18:1-BADM is the best wetting agent among the surfactants tested during this study. It has been observed that the results for foam stability measurement are consistent with those of CMC and contact angle. That is, the percentage of foam volume decrease has been observed to increase with an increase in number of hydroxyl group.     

Surfactants Synthesis Using Petroleum Fractions and Crude Oil: Application in Microemulsion Formulation

Surfactant synthesis was realized from Algerian crude oil and petroleum fractions. To predict the composition (wt%) in paraffins, naphtenes, and aromatics, the crude oil and petroleum fractions were first characterized using the n-d-PA empirical method of Robert. The characterization showed a good level in aromatics compounds which give high yield in the sulfonation reaction by oleum. The synthesized surfactants were characterized by spectroscopic techniques (UV, FTIR) and by critical micelle concentration (CMC), Krafft temperature, solubility (in aqueous and in salt solution), molecular weight, and matter actives (%) measurements. The formulation of microemulsion using synthesized surfactant from plat format petroleum fraction showed a Winsor III type system. The effect of salinity demonstrates the existence of an optimal value of NaCl concentration for which the interfacial tension takes the lowered value (10^?4 mN/m). Viscosity measurements confirm that the formulated microemulsion has a Newtonian behavior.     

改性二氧化硅纳米颗粒提高二氧化碳泡沫稳定性的研究

通过纳米二氧化硅的硅烷化改性,使其在高矿化度盐水中可以稳定存在的前提下,研究了改性纳米颗粒与阳离子表面活性剂十二烷基三甲基氯化铵混合体系的溶液稳定性及协同稳定CO₂泡沫的效果.研究结果表明,无机盐离子对改性纳米颗粒与阳离子表面活性剂间的静电吸引力具有屏蔽作用,且矿化度越高,屏蔽效果越明显,从而混合溶液更易于在高盐水中稳定;纳米颗粒表面的活性剂吸附层受二者浓度的影响,进而影响了颗粒的亲/疏水性;当混合体系中的表面活性剂浓度低于临界胶束浓度(CMC)时,混合溶液与CO₂的界面张力高于单独活性剂溶液,而当活性剂浓度高于CMC时,对CO₂-溶液界面张力几乎无影响,最低界面张力可降至6 mN/m左右;改性纳米颗粒的加入可以进一步提高CO₂体相泡沫半衰期一倍以上,但受二者浓度比例的影响;纳米颗粒的加入有效提高了多孔介质中泡沫的表观黏度,最大增幅由20 mPa·s增至55 mPa·s左右,泡沫黏度增加接近3倍,增强了CO₂泡沫驱的封堵作用.     

Interfacial activity of a novel family of polymeric surfactants

A novel series of polymeric surfactants based on carboxy methyl cellulose and alkyl poly(etheroxy) acrylate were synthesized by ultrasonic irradiation. These polymeric surfactants have exhibit excellent surface activity due to their unique structure. The influences of salt, alcohol and alkali on the interfacial activity of these polymeric surfactants were studied by interfacial tensiometery, dynamic laser scattering (DLS), UV spectroscope and environmental scanning electrical microscope (ESEM). The surface tension and interfacial tension (IFT) properties change little with NaCl added. The formed micelles shrink, their size becomes smaller. Alcohols cause the IFT to decrease a little because a small amount of free chains present in solution. Under the influence of added alkali, the IFT of the polymeric surfactants, in aqueous solution, decreases so much that sometimes it is less than 10⁻² mN/m. Using data from the equivalent alkane scan, one cannot draw the conclusion that the action of alkali with the acidic components in crude oil leads to the ultra-low IFT. The analyses by UV, DLS and ESEM show that the micelles formed by polymeric surfactants could be disaggregated or destroyed sharply by the action of alkali. So the size of micelles decreases greatly and the number of free chains increases. That more polymeric surfactants molecules move to the interface of oil/water and rearrange at the interface of oil/water is believed to be the main reason of the ultra-low IFT (10⁻³ mN/m) that is obtained.     

Synthesis of a New CO2 Philic Surfactant for Enhanced Oil Recovery Applications

The synthesis of CO₂ philic surfactant using maleic anhydride and 4-tert-butylbenzyl alcohol is reported. We reacted maleic anhydride with 4-tert-butylbenzyl alcohol to form bis(4-(tert-butyl)benzyl) fumarate and sulfonated the produced diester. The esterification reaction was optimized for a maximum yield of 98% of bis(4-(tert-butyl)benzyl) fumarate. First-order reaction kinetics with respect to acid was observed. The activation energy was found to be 55.62 kJ/mol. The sulfonated product of diester was obtained by the sulfonation reaction and the yield of 82% of surfactant was achieved. The in-house developed surfactant effectively lowered down the IFT between CO_2/brine to 4.2 mN/m. This surfactant is targeted for CO₂-EOR applications.     

Synthesis of Copolymer of Acrylamide and a Cationic-Nonionic Bifunctional Polymerizable Surfactant and Its Micellar Behavior in Water

A novel cationic-nonionic bifunctional polymerizable surfactant (PEP) was prepared by the quaternarization of poly (ethylene oxide-propylene oxide) block polymers (PEO-PPO) having terminal tertiary amine group with chloropropene. Polymeric surfactant (PAM-g-PEP) was prepared by the copolymerization of acrylamide and PEP in water and the product was confirmed by FTIR. PAM-g-PEP has exhibit excellent surface and interfacial activity and its surface tension and interfacial tension at cmc are 40.13 mN/m and 11.69 mN/m, respectively. The influence of temperature on the micellar behavior of the PAM-g-PEP in water was studied by the dynamic laser scatting (DLS) and ultraviolet spectroscope. The results showed that PAM-g-PEP in water is thermo-associative. In diluted PAM-g-PEP solution, the R_h of the polymeric surfactant increases with the temperature due to the interpolymeric aggregations are formed. In the case of concentrated PAM-g-PEP solution, the light transmittance of PAM-g-PEP aqueous solution decreases with the increasing temperature, which is may be caused by the increase of the number of the interpolymeric PEP chain aggregates.      

Mechanistic Investigation on Dynamic Interfacial Tension Between Crude Oil and Ionic Liquid Using Mass Transfer Concept

Ionic liquids (ILs) are a new kind of solvents that have recently gained an upsurge in attention in light of their unique potential for different applications. With respect to this, in the present study, applicability of an IL called 1-octadecyl-3-methylimidazolium chloride ([C18mim] [Cl]) as a new class of surfactant was investigated. Different interfacial tension (IFT) measurements were performed to find the effect of IL concentration and temperature on the IFT of water/crude oil system. The observed trend was explained based on mass transfer mechanisms including diffusion and convective mass transfer. In addition, the effect of rotational speed, ranging between 3000 and 9000 rpm, on the IFT was examined with the hypothesis that it can modify the convective mass transfer. Finally, since it has been reported that the Marangoni effect enhances the mass transfer flux in the surfactant solutions, two different methods of IFT measurements including the spinning drop and pendant drop methods were applied to investigate the effects of convective mass transfer on the equilibrium IFT.     

Phase Behavior of Microemulsions Formulated with Sodium Alkyl Polypropylene Oxide Sulfate and a Cationic Hydrotrope

The partial ternary phase diagram of anionic extended surfactant of alkyl polypropylene oxide sulfate C₁₂(PO)₄SO₄ alone and combined with the cationic hydrotrope, tetrabutyl ammonium bromide with water and decane were determined under ambient conditions. Middle phase microemulsion was formulated using salinity scans in the dilute region of surfactant/brine/decane. Visual inspection as well as cross polarizer and optical microscopy were used to detect anisotropy. Spinning drop tensiometer was used to measure interfacial tension (IFT). The first ternary phase diagram using the extended surfactant alone showed three one phase regions, the anisotropic lamellar liquid crystalline phase, L _α and the isotropic L₁ micellar liquid and L₃ sponge phase. In the second ternary phase diagram using the extended surfactant combined with tetra butyl ammonium bromide, an isotropic micellar region, L ₁, appeared in the diluted area of the phase diagram. Meanwhile the L _α phase disappeared completely and the three phase region has a bluish transparent middle phase. Interfacial tension measurements between middle phase and brine, and between decane and brine yielded ultra low values. Calculated IFT values using the characteristic length obtained using De Gennes approximation gave almost half the measured values. The interfacial rigidity was also calculated and compared to values obtained from the literature.     

Interfacial Tension Measurements Between Oil Fractions of a Crude Oil and Aqueous Solutions with Different Ionic Composition and pH

Dynamic and equilibrium interfacial tensions between crude oil fractions and aqueous solutions of various compositions and pH were measured. The basic oil components seemed to determine the interfacial tensions at pH 2, while the non-dissociated and dissociated acidic components governed the interfacial tension at the natural pH and pH 9, respectively. The ionic composition of the aqueous phase influenced the degree of dissociation of the acidic components at pH 9: Na⁺ ions in the aqueous phase promoted dissociation of the interfacial acidic components (compared to pure water), while Ca²⁺ ions resulted in complexation with the dissociated acids and most likely formation of stable interfacial films. The amount of Ca²⁺ determined which of these phenomena that dominated when both ions were present in sea water solutions. Generally, the interfacial tensions of the oil fractions were lower when measured against the high salinity aqueous solutions than against the corresponding low salinity solutions.      

Effects of a Novel Organic Alkali on the Interfacial Tension and Emulsification Behaviors Between Crude Oil and Water

Experiments have been carried out to investigate the interfacial tension (IFT) and emulsification behaviors between Shengli crude oil and a novel organic alkali (OA). The dynamic IFT and minimum IFT are adopted to characterize the IFT behaviors; the microscopic method, Turbiscan stability index, separated water rate, and laser particle size analysis method are used to show the emulsification behaviors. The dynamic and minimum IFT both decrease continuously with the increase of OA concentration whether surfactant is added or not; because of the synergy of OA and surfactant, the minimum IFT will be reduced to the ultralow value. The synergy is also crucial for the crude oil emulsification. When OA and surfactant are used together, owing to the mosaic and cross-multiple adsorption of OA, surfactant and in situ soap at the interfacial film, the oil can be emulsified more easily, the quantity of emulsified droplets is higher, and the emulsion is more stable with OA concentration increases. The relationship of the minimum IFT and emulsification is investigated; it indicates that the emulsion stability improves, the degree of dispersed homogeneity of oil droplets increases, and the median diameter of emulsified oil droplets decreases with the decline of the minimum IFT.