Effectiveness of Maleic Anhydride Grafted EPDM Rubber (EPDM-g-MAH) as Compatibilizer in NR/Organoclay Nanocomposites Prepared by Melt Compounding

The effectiveness of maleic anhydride grafted ethylene propylene diene monomer rubber (EPDM-g-MAH) as an interfacial compatibilizer in enhancing the extent of interaction between natural rubber (NR) matrix and organoclay (OC) nanolayers, and also the eventually developed microstructure during a melt mixing process, has been evaluated as an alternative material to be used in place of commonly used epoxidized NR with 50 mol % epoxidation (ENR50). The latter usually weakens the processability of the final compound. The curing behavior, rheological, and dynamic mechanical properties of the prepared nanocomposites have been evaluated. Microstructural characterizations revealed better interfacial compatibilization by EPDM-g-MAH than ENR50, which is attributed to the lower polarity of the EPDM-g-MAH and hence more affinity for the NR matrix to be diffused onto the galleries of OC. This was confirmed with transmission electron microscopy (TEM) examination and higher elasticity exhibited by the unvulcanized NR/OC/EPDM-g-MAH nanocomposites in melt rheological measurements. Also, lower damping behavior was observed for the vulcanized NR/OC/EPDM-g-MAH samples. These imply intensified polymer–filler interfacial interaction and hence restricted viscous motions by the NR segments. Vulcanized NR/OC nanocomposites compatibilized with EPDM-g-MAH showed greater enhancements in tensile properties than the sample compatibilized with ENR50.     

Comparison of Two Recent Non-Gaussian-Type Tube Models: Analysis of Mechanical Data on Unfilled Natural and Styrene-Butadiene Rubber Vulcanizates

Literature stress-strain data of filler-unfilled networks, observed in uni and biaxial deformation modes, were comparatively characterized using Hoei's finite extensibility tube model and Meissner and Matějka's primary finite extensibility tube model excluding their empirical correction term for the finite extensibility. As a result of this analysis, the former model was found to be able to more advantageously describe the stress-strain behaviors over the entire range of strain without needing the empirical correction term.     

Styrene Butadiene Rubber/Epoxidized Natural Rubber (SBR/ENR50) Nanocomposites Containing Nanoclay and Carbon Black as Fillers for Application in Tire-Tread Compounds

Nanocomposite vulcunizates based on a SBR/ENR50 (50/50%wt) rubber blend containing nanoclay (5 or 10 phr) with and without carbon black (CB 20 phr) were prepared by melt blending in an internal mixer. The compound containing 35 phr carbon black (only) was prepared as a reference sample. Microstructure of nanocomposite samples was investigated by using X-ray diffraction (XRD), melt rheo-mechanical spectroscopy (RMS), and scanning electron microscopy (SEM). The XRD patterns revealed that the distance between the clay layers were increased by adding CB to the nanocomposite samples; they caused better diffusion of chains between the layers and resulted in an intercalated structure. The RMS results also indicated the formation of the filler-filler networks. SEM images of fracture surfaces showed the presence of much roughness in the samples containing both nanoclay and CB compared to the other samples. The results obtained from application of the Flory–Rhener equation showed a high crosslink density for the sample with 10 phr nanoclay and 20 phr CB. Dynamic mechanical behavior, mechanical properties, and abrasion resistance of the nanocomposites were evaluated. The results indicated that the sample containing 10 phr nanoclay and 20 phr CB had an increased dynamic elastic modulus, reduced maximum loss factor (tanδ)_max,, and an improved tensile strength and abrasion resistance compared to the reference sample. Also, this sample showed the lowest maximum loss factor, at 50–60°C, so it can be a candidate for tire-tread application.     

A Comparative Study of the Dynamic-Mechanical Properties of Styrene Butadiene Rubber/Epoxidized Natural Rubber Dual Filler Nanocomposites Cured by Sulfur or Electron Beam Irradiation

The properties of (50/50?wt%) styrene butadiene rubber/epoxidized (50%) natural rubber (SBR/ENR50) blends containing nanoclay (NC, 5 or 10phr) without and with carbon black (CB 20phr) cured by sulfur or by electron beam (EB) irradiation (50 and 100kGy), were compared. A sulfur cured compound containing 35phr CB was prepared as a reference sample. Dynamic mechanical thermal analysis (DMTA) indicated that the sulfur cured sample containing 10phr NC and 20phr CB and the 100kGy irradiated sample with 5phr NC and 20phr CB had higher crosslink density, storage modulus, and tensile strength, and less loss factor and loss modulus, compared to the reference sample. Scanning electron microscopy (SEM) images of cryo- fractured surfaces confirmed the DMA and crosslink density results. We suggest a light weight 100kGy irradiated sample containing the lowest amount of NC and 20phr CB with a uniform distribution of the –C–C– bonds crosslinks, for high thermal stability applications and also for passenger cars tire treads, for its ice grip and wet skid properties especially for icy and wet roads, with improvements of 23% and 20%, respectively as compared to the reference sample.     

Structure and Mechanical Properties of 50/50 NR/SBR Blend/Pristine Clay Nanocomposites

A blend/clay nanocomposites of 50/50 (wt%) NR/SBR was prepared via mixing the latex of a 50/50 NR/SBR blend with an aqueous clay dispersion and co‐coagulating the mixture. The structure of the nanocomposite was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). Nanocomposites containing less than 10 phr clay showed a fully exfoliated structure. After increasing the clay content to 10 phr, both nonexfoliated (stacked layers) and exfoliated structures were observed in the nanocomposites. The results of mechanical tests showed that the nanocomposites presented better mechanical properties than clay‐free NR/SBR blend vulcanizate. Furthermore, tensile strength, tensile strain at break, and hardness (shore A) increased with increasing clay content, up to 6 phr, and then remained almost constant.     

Effect of Mixing Sequence on Phase Morphology and Mechanical Properties in Polyamide 6/Butadiene (Core) Styrene Acrylonitrile-G-Maleic Anhydride (Shell) Latex/Organoclay Ternary Nanocomposites

Ternary nanocomposites based on polyamide-6, maleated butadiene (core) -acrylonitrile-styrene (shell) rubber particles (PB-g-SAM), and modified montmorillonite (organoclay) were prepared by a twin-screw extruder. The glassy shell of the core-shell particles can act as a barrier which can resist the entrance of clay into the rubber phase. The influence of mixing sequence on the phase morphology and mechanical properties were studied. The microstructure of the ternary nanocomposites was characterized by X-ray diffraction, transmission electron microscopy, and scanning electron microscopy. It was found that the clay in the polyamide nanocomposites was partially exfoliated, exhibiting a mixture of exfoliated structures. The organoclay plates affected the interfacial adhesion between the polyamide-6 and the core-shell particles. The location of the organoclay plates in the blends with different mixing sequences produced differences of the mechanical properties. The results of mechanical testing revealed that the optimum mixing sequence to achieve balanced mechanical properties was mixing the polyamide-6 and organoclay first followed by mixing with the core-shell particles.     

Comparison of Structure,Morphology, and Properties of Miktoarms Star Styrene-Butadiene Rubber and Star-Shaped Styrene-Butadiene Rubbe/Polybutadiene Rubber Blends

Four miktoarms star-shaped polybutadiene-Sn-poly(styrene-butadiene) rubber (MSS-PB-PSBR) with 1,1-diphenylhexyl at the ends of the arms were prepared by two different coupling techniques. One technique was a one-step technology, from which two miktoarms star styrene-butadiene rubbers, called AMSS-PB-PSBR, were obtained in which the four arm stars had varying ratios of PB:PSBR arms; another was a two-step technology, from which another two miktoarms star styrene-butadiene rubbers, called BMSS-PB-PSBR, were obtained in which all consisted of PB-Sn-(PSBR)₃ stars. The molecular structure parameters and morphology-properties of the four MSS-PB-PSBR were determined and studied, and compared with that of a star-shaped styrene-butadiene rubber (S-SSBR)/poly butadiene rubber (PBR) blend. The results showed that the total coupling efficiency (the ratio of the total number of polymer chains (arms) coupled by SnCl₄ to that of the total number of polymer chains) of the MSS-PB-PSBR was higher than 60%. However, the coupling efficiency of the polybutadiene arms of BMSS-PB-PSBR was obviously higher than that of the AMSS-PB-PSBR. Compared with the S-SSBR/PBR blend, MSS-PB-PSBR had a more uniform distribution of the PB phase and a smaller phase size of PB. It was found that MSS-PB-PSBR composites filled with carbon black (CB) had a lower Payne effect than the S-SSBR/PBR/CB composite, with the BMSS-PB-PSBR/CB composites being especially lower. The BMSS-PB-PSBR/CB composites had higher mechanical properties and lower rolling resistance than the AMSS-PB-PSBR/CB composites due to the high coupling efficiency of the polybutadiene arms; the results indicated that the two-step technology was better than the one-step technology for preparing the tread material of “green” tires.     

Comparative Properties of Styrene-Butadiene Rubbers (SBR) Containing Pyrolytic Carbon Black,Conventional Carbon Black,and Organoclay

To evaluate the reinforcing potential of pyrolytic carbon black, styrene-butadiene rubber (SBR) was filled with pelletized pyrolytic carbon black (pCB_p), N660 industrial CB, their blend in a 1/1 ratio, and the latter also in the absence and presence of additional organoclay (OC). The Shore A hardness of the filled SBR gums was 65 ± 2°. Effects of the compositions on the filler dispersion, cure behavior, dynamic mechanical thermal parameters (including the Payne effect), tensile mechanical (including the Mullins effect), and fracture mechanical (making use of the J-integral concept) properties were studied and discussed. Though pCB_p had a higher specific surface weight than CB, the latter proved to be a more active filler with respect to the tensile strength. The opposite tendency was found for the tear strength and fracture mechanics characteristics (J-integral at crack tip opening, tearing modulus, and trouser tear strength). This was traced to an enlargement in the crack tip damage zone supported by the dispersion characteristics of the pCB_p. The performance of pCB_p was similar to that of CB with respect to some other properties. OC supported the filler networking which positively affected the resistance to crack initiation.     

Preparation of Silicon Carbide Nanoparticle/Butadiene Rubber/Silane Nanocomposites; Structural,Mechanical, Tribological and Thermal Properties

Silicon carbide nanoparticles (nano-SiC), in the amounts of 0, 3, and 5 parts per hundred of rubber (phr), were employed in a butadiene rubber (BR) based compound as a potential commercial rubber and the structure, mechanical, tribological and thermal properties of the samples were investigated. The use of 3 phr of nano-SiC, especially in the presence of silane, increased the crosslink density and improved the tensile strength (35%) and elongation at break (64%) of the BR. In addition; the abrasion resistance of the BR was improved about 120% and the coefficient of friction increased. Scanning electron microscopy (SEM) images revealed the use of silane resulted in an appropriate dispersion of the nano-SiC and improvement of its interaction with the matrix. The use of nano-SiC, especially with silane, increased the initial thermal decomposition temperature of the BR and decreased its rate of degradation.     

The Effect of Structure of the Clay Modifier on the Morphology and Properties of Polystyrene/Clay Nanocomposites Prepared via In Situ Suspension Polymerization

Polystyrene (PS)/organoclay nanocomposites were prepared via free radical suspension polymerization. Two kinds of organoclay were used, labeled KT and KD, modified by trimethyloctadecyl ammonium (TM) and dimethyldioctadecyl ammonium (DM) ions, respectively. Nanocomposites containing various amounts of both of the organoclay nanoparticles (1, 3, and 5 wt%) were prepared. The wide angle X-ray diffraction (WAXD) results revealed intercalation in both of the nanocomposites. The greatest improvement in thermal stability of the nanocomposites was achieved with 5 wt% of organo-MMT for both of the clays. The nanocomposite containing 3 wt% of KT organo-MMT showed the greatest improvement of storage modulus. When the organoclay content exceeded 3 wt%, the storage moduli decreased compared to the nanocomposite filled with 3 wt% of the organoclay. D-spacing calculations using Bragg's law and WAXD data showed that the KT and KD nanoparticles were intercalated within the PS matrix, but with different extents of intercalation. The styrene conversions of the as-polymerized nanocomposite samples were obtained by a gravimetric method. The results showed that conversion decreased with incorporation of organoclay in the reaction recipe. Particle size was also increased by increasing nanoclay content.     

Thermoplastic Elastomers Based on Natural Rubber/Polypropylene Blends: Effect of Blend Ratios and Dynamic Vulcanization on Rheological,Thermal, Mechanical,and Morphological Properties

Thermoplastic elastomers (TPEs) based on natural rubber (NR)/polypropylene (PP) with different blend ratios were prepared and studied. The TPEs were obtained by dynamic vulcanization of NR/PP using a sulfur (S)/N-tert-butyl-2-benzothiazolesulphenamide (TBBS) and tetramethylthiuram disulphide (TMTD) curative system during processing in the melt state in an internal mixer equipped with cam rotors. Rheological, thermal, mechanical, dynamic, and morphological properties of the TPEs prepared were investigated. Based on this study a mechanism for the NR crosslinking was proposed where the sulfur vulcanization occurs through radical substitution in the forms of polysulfide bridges. The dynamic vulcanization process increases the stiffness of the NR phase in the TPEs and modifies the rheological and thermal behavior of the system compared to the behavior of the basic material PP. The crosslinked NR particles restrict the spherulitic growth and the regular arrangement of the spherulites of PP phase, decreasing the crystallinity degree. On the other hand, a reduction of mobility of the chain segments was also observed and, consequently, an increase of the T_g values. NR/PP TPEs with high content of NR showed superior mechanical performance compared to the uncrosslinked NR/PP blends in terms of tensile strength, Young's modulus and hardness. An increase of approximately 320% in Young's modulus values was obtained for the NR70/PP30 TPE compared to NR70/PP30. Morphological studies revealed the formation of large aggregates of NR domains in NR/PP TPEs which increased in size with an increase of the rubber content.     

Effect of Surfactant Concentration on Thermal and Mechanical Properties of Poly(Butylene Succinate)/Organoclay Composites

Composite materials consisting of poly(butylene succinate) (PBS) and montmorillonite (MMT), modified to various extents using trihexyltetradecylphosphonium chloride (THTDP) cations, were prepared using a simple melt intercalation technique. The surfactant contents were varied, i.e. 0.4, 0.6, 0.8, 1.0, and 1.2 times the cation exchange capacity (CEC) of the MMT. The intercalation of the surfactant molecules into MMT layers, confirmed by the increase in interlayer spacing and significant changes in the morphology of the modified MMT, facilitated the dispersion of the clay in the PBS matrix. The properties of the PBS-based composites were changed with increasing surfactant content. The melting and crystallization temperatures increased and the degree of crystallinity (χ_c) decreased. The storage modulus was significantly enhanced below the glass transition temperature (Tg), and Tg shifted to a higher temperature, with a maximum at a surfactant loading of 0.6 CEC. The mechanical properties, including tensile strength, flexural strength, flexural modulus and impact strength, increased and then decreased with surfactant loading, with the maximum observed also at a surfactant loading of 0.6 CEC. In conclusion, an ideal balance between thermal and mechanical properties can be obtained at a surfactant quantity equivalent to 0.6 times the clay CEC. Moreover, all the composites exhibited obvious improvement in thermal and mechanical properties as compared to those of neat PBS.     

Statistical Analysis of Morphology of Low Density Polyethylene/Polyamide 6 Blends with Addition of Organoclay and Maleic Anhydride-Grafted Polystyrene-b-Poly(Ethylene-co-Butene-1)-b-Polystyrene Copolymer As Compatibilizers

Statistical analysis of the size distribution of a polymer minor phase droplets was successfully applied for the characterization of the morphology in a LDPE/PA6 blend (75/25 wt/wt) obtained after mixing with added SEBS-g-MA(S) compatibilizer and/or organoclay 20A. It was shown that the developed approach provided detailed analysis of the morphology development in the polymer blends, including the primary droplets formation of the minor polymer phase and their break-up and coalescence. The introduction of organoclay increased the break-up of primary droplets and completely suppressed their coalescence. The addition of compatibilizer S, in contrast to nanoclay, did not suppress coalescence but the mean size of the primary droplets as well as the droplets formed at coalescence was strongly reduced. The combined addition of compatibilizer S and nanoclay did not change the morphology development of the LDPE/PA6 blend. Both processes of the droplet transformation were accelerated, similar to the system with addition of compatibilizer S only. However, an increase of nanoclay amount disturbed the break-up of the primary droplets, and the mean size of these droplets increases. Thereafter, the mean size of droplets formed at coalescence also increased. The results of statistical analysis of the phase morphology were found to correlate with the mechanical properties of the polymer blends. The fine dispersion of the minor polymer phase improved the stiffness of the polymer blends. For enhanced impact properties, the presence of relatively broad distribution of the minor polymer phase was necessary.     

Effect of Wood Flour on the Curing Behavior,Mechanical Properties,and Water Absorption of Natural Rubber/Wood Flour Composites

The preparation of natural rubber/wood flour (NR/WF) composites and the influence of WF content, modification, and particle size on the vulcanizing behavior, mechanical properties, and water absorption of NR/WF composites are described. Results show that the addition of WF into NR delayed the scorching time and vulcanizing time of NR. The appropriate WF contents can improve the mechanical properties of NR. However, the overloading of WF destroys the mechanical properties of NR. The addition of WF increased the water absorption of NR. The silicone couple agents that were used to modify the WF had little effect on the water absorption of NR/WF composites. Decreasing the WF particle size enhanced the water absorption of NR/WF composites because the water-absorbing surface area increased with decreasing WF particle size. The water absorption of sisal-fiber-filled NR-based composites was larger than that of the WF-filled NR-based composites. A useful equation, w=ktⁿ , was inferred from the water absorption results to calculate the water absorption (w) of the NR/WF composites as a function of time (t), where k was a constant concerning the compounds’ character that was primarily determined by the WF's character and n was the power of time that was related to the NR's inherent character, such as cross-linking density, and primarily determined the water absorption rate.     

Characterization of Filler-rubber Interaction,Filler Network Structure,and Their Effects on Viscoelasticity for Styrene-butadiene Rubber Filled with Different Fillers

For styrene-butadiene rubber (SBR) compounds filled with the same volume fraction of carbon black (CB), precipitated silica and carbon–silica dual phase filler (CSDPF), filler-rubber interactions were investigated thru bound rubber content (BRC) of the compounds and solid-state ¹H low-field nuclear magnetic resonance (NMR) spectroscopy. The results indicated that the BRC of the compound was highly related to the amount of surface area for interaction between filler and rubber, while the solid-state ¹H low-field NMR spectroscopy was an effective method to evaluate the intensity of filler-rubber interaction. The silica-filled compound showed the highest BRC, whereas the CB-filled compound had the strongest filler-rubber interfacial interaction, verified by NMR transverse relaxation. The strain sweep measurements of the compounds were conducted thru a rubber process analyzer; the results showed that the CSDPF-filled compound presented the lowest Payne effect, which is mainly related to the weakened filler network structure in polymer matrix. The temperature sweep measurement, tested by dynamic mechanical thermal analysis, indicated that the glass transition temperature did not change when SBR was filled with different fillers, whereas the storage modulus in rubbery state and the tanδ peak height were greatly affected by the filler network structure of composites.     

Effect of Silanes on Mechanical and Thermal Properties of Silicone Rubber/EPDM Blends

The effect of four types of silane coupling agents on the mechanical and thermal properties of silicone rubber and ethylene–propylene–diene monomer (M-class) rubber (EPDM) blends is studied, namely, isobutyltriethoxysilane (BUS), acryloxypropyltriethoxysilane (ACS), aminopropyltriethoxysilane (AMS), and vinyltriethoxysilane (VIS). ACS and VIS increase the crosslink density of the blends, which results in higher tensile strength, modulus, and thermal stability, but lower elongation at break compared with the other silanes. However, the blend containing BUS shows highest tanδ in the temperature range of 45°C to 200°C. Thermogravimetric analysis shows two steps of degradation for all the samples, but little difference with the varied silanes.     

Preparation and Properties of Natural Rubber (NR)/Polycaprolactone (PCL) Bio-Based Shape Memory Polymer Blends

Shape memory NR/PCL bio-based blends, where NR served as the reversible phase and PCL served as the switching phase, were prepared using a melt blending process. Peroxide, besides its role as a cross-linking agent to NR, was used to enhance the compatibility between NR and PCL, which was confirmed via Fourier transform infrared spectra and scanning electron microscopy analyses. With increasing peroxide content, the tensile strength increased steadily with decreasing PCL contents, up to 12.3 ± 0.8 MPa for the NR/PCL (70/30) blend at 2 phr peroxide. The shape fixing ratio decreased slightly with increasing peroxide content, especially for high NR content. The values of the shape recovery ratio were high, up to 100%, regardless of PCL content. The recovery stress was found to reach its maximum value around 60°C. In order to consider both fixing ratio (R_f) and recovery ratio (R_r) together, an additional denotation of shape memory index, R_fR_r, coupling both ratios by the product of the fixing ratio and recovery ratio, is proposed. The shape memory index (R_fR_r) reached values close to 100%, at the NR/PCL composition of 50/50 and 70/30; in particular, the highest value was for the 50/50 case regardless of peroxide concentration. The shape recovery ratio and fixing ratio remained largely unchanged even after 30 cycles of deformation and recovery processes for a typical NR/PCL/DCP (30/70/0.5) blend which, thus, outperformed all known shape memory blends in the literature.     

Properties of Natural Rubber Vulcanizates/Nanosilica Composites Prepared Based on the Method of In-situ Generation and Coagulation

Using the characteristics of silica sol dispersing well in water and easy formation of silica gel when the silica sol is heated, by mixing a system of concentrated natural rubber latex and silica sol, the silica sol can in-situ generate SiO₂ particles when heated. After coagulation of the mixed system, natural rubber/nanosilica composites C(NR/nSiO₂) were obtained. The composites C(NR/nSiO₂) and their vulcanizates were studied using a rubber processing analyzer (RPA), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The influence of silica contents on the C(NR/nSiO₂) vulcanizates mechanical properties, cross-linking degree, Payne effect, dissipation factor (tanδ), and the particle size and dispersion of SiO₂ in NR were investigated. The results obtained were compared with the NR/SiO₂ composites based on traditional dry mixing of bale natural rubber and precipitated silica (white carbon black). The results showed that when using a sulfur curing system with a silica coupling agent (Si69) in C(NR/nSiO₂), the vulcanizate had better mechanical properties, higher wet resistance, and lower rolling resistance than those without Si69. In the composites C(NR/nSiO₂) and their vulcanizates, the SiO₂ particles’ average grain diameter was 60 nm, and the good-dispersion of the in-situ generated SiO₂ in the rubber matrix were a significant contribution to the satisfactory properties of C(NR/nSiO₂) composites and their vulcanizates.     

聚合物分子与官能化纳米管相互作用及扩散特性的分子动力学模拟

用全原子分子动力学方法研究典型聚合物分子（PE,PEO和PP）与碳纳米管（CNT）及官能化碳纳米管（FCNT）界面的相互作用及扩散特性.动力学模拟显示：—CH₃官能团具有减弱CNT与PE和PP的相互作用,但是,—CH₃官能化后的CNT与PEO之间确有增强作用.分析含氧官能团（—OH和—COOH）官能化的CNT与PE,PEO和PP的相互作用,可知含氧官能团的确具有增强表面相互作用的功能,而且含氧原子越多,相互作用就越强.此外,—CH₃,—OH,—COOH官能化后的CNT与PE,PP和PEO体系的总能量均减少,而且能量满足—COOH < —OH < —CH₃.分析非键相互作用势（库仑能和范德瓦尔斯能）,可知库伦相互作用是增强界面相互作用的主要作用能.官能化后的CNT/PE,CNT/PEO,CNT/PP体系的扩散系数都明显减小,且扩散系数大小满足—COOH < —OH < —CH₃.     

Rheology,Crystallization, Mechanical and Barrier Properties of Polyamide 6/66 Nanocomposites with Exfoliated Organoclays

Nylon copolymer/clay (NC) nanocomposites were prepared using PA6/66 as a matrix and organoclay as a nanofiller through a two-step melt-compounding method. It was shown that the organoclay flakes were well exfoliated and dispersed in the PA6/66 matrix. With increasing content of organoclay, the apparent shear viscosity and the entrance pressure drop of the NC nanocomposites decreased whereas the corresponding shear activation energy increased, suggesting that the NC nanocomposites were suitable to be used in shear-flow rather than extension-flow related processes. Investigations of the crystallization behaviors of the NC nanocomposites indicated that the organoclay addition was capable of facilitating the γ-form crystal formation, which is suggested to be due to the restriction effect of the organoclay on the PA6/66 chain motion during the crystallization. Compared to the neat PA6/66, the tensile strength and elongation at break of the NC nanocomposites were both enhanced at an appropriate content of the organoclay. In addition, the NC nanocomposites exhibited enhanced barrier properties due to the high specific surface area and the homogeneous dispersion of the organoclay.