Microwave-Assisted Synthesis and Characterization of Poly(2-(dimethylamino)ethyl methacrylate) Grafted Gellan Gum

Poly(2-(dimethylamino)ethylmethacrylate) was grafted on gellan gum (GG) in aqueous medium under microwave irradiation using ammonium persulfate and N,N,N′N′-tetramethylethylenediamine as the initiation system. Grafted copolymers were characterized by FT-IR, TGA, and SEM techniques. The influence of microwave power, exposure time, and composition of the reaction mixture on extent of grafting was studied. Conditions for obtaining the highest degree of grafting were optimized. The rate of grafting was determined from weight measurements. The overall activation energy for grafting is found to be 31.2 kJ/mol, indicating the occurrence of the grafting process with absorption of low thermal energy.     

Alumina supported synthesis of Cassia marginata gum‐g‐poly(acrylonitrile) under microwave irradiation

In view of the known advantages of the microwave promoted reactions done in dry medium, the seed gum sourced from Cassia marginata has been graft copolymerized with acrylonitrile in dry medium at neutral alumina support under microwave irradiation. Grafting conditions were optimized and the representative graft copolymer was characterized by Fourier transform‐infrared, Thermo gravimetric analysis, Scanning electron microscopy, and X‐Ray Diffraction (XRD) measurement, taking Cassia marginata gum (CM) as reference. Much higher % grafting and % efficiency could be obtained in the microwave promoted alumina supported grafting as compared to grafting done in aqueous medium (microwave promoted and conventional). Properties of the microwave synthesized Cassia marginata gum‐graft‐poly(acrylonitrile) (CM‐g‐PAN) were studied and compared with the parent seed gum. © 2007 John Wiley & Sons, Ltd.     

Preparation of poly(ε-caprolactone)-co-poly(acrylic acid) by radiation-induced grafting

Acrylic acid was grafted onto poly(ε-caprolactone) (PCL) films by using electron beam (EB) preirradiation technique. The effect of reaction time, monomer concentration, radiation dose, time between irradiation and grafting, radiation atmosphere, and polymer crystallinity on the extent of grafting were studied. Silver and tin ions were attached to the grafted chains in order to study the grafting process. The irradiation in air was initially more rapid, but the final extent of grafting was the same when irradiated in nitrogen atmosphere. Maximum grafting extents exceeding 400% could be obtained. The optimal grafting was obtained at an acrylic acid to water ratio of 30 : 70. The grafting process could be initiated at a dose as low as 12 kGy. The grafting process proved to start at the surface and was extended into the bulk with time. The ability to form crystals was reduced as the grafting extent increased. The water uptake of the poly(ε-caprolactone)-graft-poly(acrylic acid) was increasing with increasing grafting extent, but reached a maximum of ca 100% for all grafting extents above 85%. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1805–1812, 1998     

Microwave Assisted Graft Copolymerization of N-Isopropyl Acrylamide and Methyl Acrylate on Cellulose: Solid State NMR Analysis and CaCO3 Crystallization

Summary: Graft copolymerization of N-isopropyl acrylamide and methyl acrylate on α-cellulose was carried out under microwave irradiation at specific cut off temperatures with cerium (IV) ammonium nitrate and potassium persulfate (KPS) as the initiating system. The role of KPS was to oxidize Ce (III) to Ce (IV) which is the active species in radical formation. The reactions at a temperature cut off of 60 °C were confirmed by ¹³C nuclear magnetic resonance cross-polarization with magic- angle spinning (¹³C NMR CP/MAS) and Fourier-transform infrared spectroscopy (FTIR). The extent of grafting was calculated from weight gain and ¹³C resonances. The grafted cellulose was thermally more stable than the parent cellulose. An attempt to do grafting at a higher cut off temperature of 80 °C was made, however, no grafting was observed from ¹³C NMR CP/MAS but TGA results showed that a cellulose having more thermal stability resulted which was attributed to cross linking. Crystallization of CaCO₃ was carried out using the grafted materials as templates showed better nucleation and different crystal structure was observed.     

Radiation-induced graft copolymerization of N-vinyl carbazole and methyl methacrylate onto cellulose acetate film

N-Vinyl carbazole methyl methacrylate, and the binary mixtures of these monomers were grafted onto cellulose acetate films by taking recourse to Co-60 simultaneous irradiation grafting technique. The effect of various parameters (e.g., solvents, radiation dose, compositions of the monomers, and concentration of the monomers) on the extent of grafting in unitary and binary systems were studied. The optimum conditions for grafting were evaluated. The sensitizing effect of one monomer in the presence of other in the binary system was identified. The relative molecular reactivity and reactivity ratios were computed and these were used in explaining sensitization and the effect of monomer compositions on the extent of grafting in the binary system.     

Grafting vinyl monomers to starch by ceric ion. I. Acrylonitrile and acrylamide

Studies were carried out on the grafting of acrylonitrile (AN) and acrylamide (AA) to starch by ceric ion. The variables affecting the grafting of AN and AA were investigated with granular wheat starch dispersed in aqueous N,N-dimethylformamide and ceric ammonium nitrate as catalyst. Results showed that the concentrations of monomer and catalyst are the major factors influencing the grafting of AN; thus the monomer content of the grafts can be regulated by these variables. The grafting of AA is also influenced by these variables, but to a much less degree. Increasing concentrations of monomer promote homopolymerization and increasing concentration of catalyst inhibit grafting. The extent of grafting of this monomer can best be controlled by reaction time. Under the most favorable conditions, maximum grafting efficiency (ratio of amount of grafted monomer to total amount of monomer converted to polymer) was 87% for AN and 43.8% for AA. Although the monomer content of the AN grafts was higher than that of AA grafts prepared under identical conditions, the number of branches in the grafts was almost the same; only the length of the branches was different. The AN-starch grafts have branches of higher molecular weight.     

Radiation-induced grafting of acrylamide onto guar gum in aqueous medium: Synthesis and characterization of grafted polymer guar-g-acrylamide

Mutual radiation grafting technique has been applied to carry out grafting of acrylamide (AAm) onto guar gum (GG) using high-energy Co⁶⁰ γ radiation to enhance its flocculating properties for industrial effluents. The grafted product was characterized using analytical probes like elemental analysis, thermal analysis, Fourier transformed infrared (FTIR), X-ray diffraction (XRD) and scanning electron microscope (SEM). The grafting extent was observed to decrease with the dose rate and increase with the concentration of AAm. Thermo gravimetric analysis (TGA) of grafted and ungrafted samples indicated better stability of grafted product. γ and microwave radiation effect on grafted and virgin GG has also been reported.     

Analysis and Characterization of Microwave Irradiation–Induced Graft Copolymerization of Methyl Methacrylate onto Delignified Grewia Optiva Fiber

Grafting of methyl methacrylate (MMA) onto delignified Grewia optiva fiber using ascorbic acid/H₂O₂ as an initiator was carried out under microwave irradiation. The effects of varying the microwave power, exposure time, and concentration of initiator and monomer of graft polymerization were studied to obtain maximum grafting percentage (26.54%). The experimental results showed that the optimal conditions for grafting were: exposure time, 10min; microwave power, 110 W; ascorbic acid concentration, 3.74mol/L × 10^?2; H₂O₂ concentration, 0.97mol/L × 10^?1; monomer concentration, 1.87mol/L × 10^?1. The graft copolymers were characterized by Fourier transform-infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA).     

Radiation grafting of acrylonitrile on ethylene-propylene diene terpolymer rubber: Optimization of grafting parameters and oil resistance properties

Radiation induced grafting of acrylonitrile (ACN) on ethylene-propene diene terpolymer (EPDM) rubber film was investigated by mutual radiation grafting technique. Effect of experimental variables viz. radiation dose, dose rate, type of solvent and monomer content on extent of grafting was studied. From the kinetic studies a mathematical relation R _g α[M]^0.7 D ^0.68 showing non-linear relationship for rate of grafting with monomer concentration and dose was deduced. The grafted samples showed increased hardness and oil resistance.     

Radiation-induced graft copolymerization of mixtures of styrene and acrylamide onto cellulose acetate. III. A kinetic study

The kinetics of graft copolyermization of styrene and acrylamide from their binary monomer mixtures onto gamma-irradiated cellulose acetate film was studied. The extent of grafting increased with a rise in reaction time and temperature. The nature of the radical site on the trunk polymer was acertained in a study of grafting at different temperatures when the trunk polymer was irradiated in the presence and absence of oxygen. The character of the radical was tested further in a study of the ESR spectrum. The variation in grafting rates and energies of activation required for graft copolyermization at various mole ratios of the monomers was observed. The grafting rates showed a maximum at 1:1 mol ratio of monomers which was also associated with minimum energy of activation. The Kk_t values in the system were dependent on the composition of monomers.     

Preirradiation grafting of N-vinyl-2-pyrrolidone onto poly(tetrafluoroethylene) and poly(tetrafluoroethylene-hexafluoropropylene) films

Preirradiation grafting of N-vinylpyrrolidone (NVP) onto poly(tetrafluoroethylene) (PTFE) and poly(tetrafluoroethylene-hexafluoropropylene) (FEP) films was investigated. The influence of grafting parameters such as preirradiation dose, monomer concentration, and grafting temperature on the rate and grafting yield was studied. Different solvents were used for diluting the monomer and it was found that the aqueous monomer solution at a concentration of 80 wt% was suitable for this grafting system. However, the graft polymerization of NVP in benzene terminated within a short time without significant grafting yield. The dependence of the grafting rate on preirradiation dose and monomer concentration was 1.2 and 1.07 order, respectively, for grafting onto PTFE films and 1.1 and 1.2 order, respectively, for grafting onto FEP films. Arrhenius plots for grafting onto PTFE films showed a breaking point at ca. 35°C and the overall activation energies were calculated as 23.6 and 9.0 Kcal/mol below and above 35°C, respectively. For grafting onto FEP films, however, no break was observed in the Arrhenius plots; the overall activation energy was 11.9 Kcal/mol. The swelling behavior and electric resistance of the grafted materials were investigated.     

Synthesis and characterization of poly(vinyl ferrocene) grafted hydroxyl-terminated poly(butadiene): A propellant binder with a built-in burn-rate catalyst

The graft copolymer hydroxyl-terminated polybutadiene-g-polyvinyl ferrocene (HTPB-g-PVF) was synthesized free radically from HTPB and vinyl ferrocene (VF) in benzene, using azobisisobutyronitrile as the radical initiator at 75°. The graft copolymer was analysed for its structural and thermal characteristics. The chemically bound ferrocene in HTPB-g-PVF, catalysis the oxygen up-take and oxidative degradation reactions of HTPB, and the mechanisms of the catalysis are discussed. The most probable grafting sites on HTPB and the mechanism of grafting also are discussed. The extent of the grafting, which was a function of VF concentration, was low. The graft copolymer also was tried as a propellant-binder-cum-burn-rate (BR) catalyst in a composite solid propellant, using toluene diisocyanate and trimethylol propane as curatives with dibutyl tin dilaurate as the curing catalyst, and the BRs of the propellants were evaluated at 3.9 MPa. The BRs increased with the extent of VF grafting but not proportionally. The BRs also were compared with those of reference HTPB propellants containing VF, Fe₂O₃, copper chromite, and so forth as BR catalysts. Chemically linked ferrocene in the binder augmented the propellant BR, probably because of the presence of catalytically active sites in the binder for its degradation. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4090–4099, 1999     

Poly(vinyl acetate‐co‐dibutyl maleate) latex films in the presence of grafted and post‐added poly(vinyl alcohol)

We describe the synthesis and characterization of a series of poly(vinyl acetate‐co‐dibutyl maleate) [P(VAc‐DBM)] latex particles (monomer molar ratio 10.6:1). One set of samples [high‐M and M_250k SDS‐P(VAc‐DBM), gel content 50% and 0%] was prepared in the presence of an anionic surfactant sodium dodecyl sulfate. The other two sets of samples [high‐M and M_250k PVOH–P(VAc‐DBM)] were prepared in the presence of poly(vinyl alcohol) (PVOH). These polymers differ in gel content (50 and 0%) and the extent of PVOH grafting (30 and 15%). Polymer diffusion across cell boundaries in the latex films was monitored by fluorescence resonant energy transfer (ET) experiments. First, we examined M_250k samples in the presence of grafted and post‐added PVOH. The presence of post‐added PVOH (5%) causes a small but detectable retardation on the rate of polymer diffusion, whereas the presence of grafted PVOH (degree of grafting: 15%) significantly promotes the polymer diffusion rate. For the high‐M P(VAc‐DBM), the presence of post‐added PVOH also retards the polymer diffusion. Strikingly, the presence of grafted PVOH (degree of grafting: 30%) in the high‐M PVOH‐P(VAc‐DBM) promotes the polymer diffusion to such an extent that the diffusion was complete in the freshly prepared films. Our data also suggest that under our experimental conditions, the rate of P(VAc‐DBM) diffusion increases with an increase of the degree of PVOH grafting. To confirm these results, we carried out fluorescence microscopy experiments to monitor the fate of PVOH in these latex films and found that in newly formed PVOH–P(VAc‐DBM) films, the PVOH was either uniformly distributed in the P(VAc‐DBM) matrix or the domains were too small to be resolved (i.e., < 0.5 μm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5005–5020, 2004     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Improved microwave absorption and electrostatic charge dissipation efficiencies of conducting polymer grafted fabrics prepared via in situ polymerization

Polyaniline (PANI) and polypyrrole (PPY) were grafted over cotton fabrics by in situ polymerization. FTIR spectra show systematic shifting of bands corroborating surface grafting of conducting polymers on cotton fabric. SEM images revealed that the surface coating of PANI was smoother than PPY. However, better control over coating thickness and uniformity was achieved in PPY fabric. The probable formation mechanism of grated fabrics has also been proposed. The good thermal stability and acceptable electronic conductivity values indicate that these fabrics could be used for electrostatic charge dissipation and microwave absorption. The antistatic studies have shown complete charge dissipation (decay time <0.01 sec). The microwave absorption studies of the conducting fabrics in X‐band (8.2–12.4 GHz) show absorption dominated total shielding effectiveness in the range ?11.3 to ?11.7 dB (>92% attenuation) and ?9.2 to ?9.6 dB (>88% attenuation) for fabrics grafted with PPY and PANI, respectively. Copyright © 2011 John Wiley & Sons, Ltd.     

Radiation-induced graft copolymerization of mixtures of styrene and acrylamide onto cellulose acetate. I. Effect of solvents

The grafting of styrene and acrylamide, from both their binary and unitary systems, on cellulose acetate film was studied by means of the cobalt-60 postirradiation grafting technique. The extent of grafting was found to be dependent on preirradiation dose, reaction time, and temperature, and the optimum conditions were evaluated. The effect of solvents, e.g., water, methanol, ethanol, isopropanol, and t-butanol were studied. The composition of the binary mixture as well as the nature of the alcohol used as the solvent were found to have a strong influence in modifying the course of grafting. Each component of the binary monomer mixture was found to sensitize the grafting of the other, when the former is present in relatively large concentration. The observed results are discussed in detail in terms of relative molecular reactivity and reactivity ratios.     

微波作用下的多肽固相缩合反应及动力学研究

分别在微波作用以及传统加热两种方式下, 研究了Fmoc-Val-OH与NH₂-Tyr(t-Bu)-Wang树脂的固相缩合反应及其动力学. 测定了温度变化对反应速率的影响, 并获得了两种方式下的缩合反应的宏观动力学参数: 300 W微波作用下表观缩合反应级数为2.3, 活化能为104.7 kJ/mol; 传统方法中表观反应级数为2.9, 活化能为142.4 kJ/mol. 微波作用将常规条件下的连接率由68%提高到95%, 而所需时间降为常规条件的1/14.     

微波辐照下（Bi_2O_3）_（0．8）（La_2O_3）_（0．2）固熔体对甲

微波辐照下（Ｂｉ_２Ｏ_３）_（０．８）（Ｌａ_２Ｏ_３）_（０．２）固熔体对甲烷氧化偶联的催化行为陈长林,洪品杰,戴树珊,阚家德（云南大学化学系,昆明,６５００９１）关键词微波,甲烷氧化偶联,（Ｂｉ_２Ｏ_３）_（０．８）（Ｌａ_２Ｏ_３）_（０．２）甲烷氧化...     

单模微波辐照下壳聚糖-左旋聚乳酸接枝共聚物的酶催化合成

以猪胰脂肪酶(PPL)代替传统的有机金属作为催化剂,在单模微波辐照下利用左旋丙交酯(L-LA)的开环聚合制备壳聚糖-左旋聚乳酸(CS-g-PLLA)接枝共聚物.考察了反应温度及酶用量对接枝率的影响.以此为基础,利用DTG、XRD和3T3成纤维细胞培养对产物的物理性能及细胞相容性进行分析.结果显示,猪胰酶可有效催化接枝反应的进行.反应温度和酶用量对产物的接枝率有较大影响.在单模微波作用下,较低的反应温度(50℃)可获得具有较高接枝率(178.8%)的接枝产物.与纯壳聚糖相比,接枝产物的结晶度和热稳定性降低,说明PLLA的引入破坏了壳聚糖的高结晶性.产物具有良好的细胞相容性,可作为优良的组织工程支架材料.     

Kinetics and mechanism of the grafting of 2-(dimethylamino)ethyl methacrylate onto hydrocarbon substrates

The kinetics of grafting a basic monomer, 2-(dimethylamino)-ethyl methacrylate (DMAEMA) to hydrocarbon substrates have been investigated. These systems were chosen as models for the grafting of a homopolymerizable monomer to polyolefins such as polyethylene. The reactions with squalane and n-eicosane were initiated by an organic peroxide, 2,5-dimethyl 2,5 dit-butylperoxy)-3-hexyne; grafting yields become significant at high reaction temperatures and low monomer concentrations. In squalane, the order of reaction with respect to monomer increased from about 1.1 for 0.22?0.44M DMAEMA to almost 2 at 0.69M DMAEMA; the order with respect to initiator was 0.56. The overall activation energy in the 130?160°C temperature range was, however, surprisingly low, 42±5 kJ mol^?1. When analytical data were used to separate the overall rate into those for grafting and homopolymerization, different kinetic paths were observed for the competing reactions. These results are interpreted in terms of two different mechanisms; intramolecular chain transfer plays an important role in grafting, while depropagation becomes a major factor in homopolymerization at temperatures above 150°C. © 1995 John Wiley & Sons, Inc.