Photo-lithographically impregnated and molecularly imprinted polymer thin film for biosensor applications

A voltammetric sensor for albuterol was investigated where we combined the techniques of microfabrication and molecular imprinting to construct on-chip devices using photoirradiation of cross-linkable polymers. Molecularly imprinted polymer was coated as a thin film onto the gold working electrode on chip and the analyte was directly quantified by differential pulse voltammetric measurements.     

A novel molecularly imprinted polymer thin film as biosensor for uric acid

A novel amine-imide type conducting polymer, denoted as poly(PD-BCD), was molecularly imprinted on an indium-tin oxide (ITO) glass, with uric acid (UA) as the template and without any functional monomer. Intending to improve the imprinting efficiency, the polymer content was varied from 0.3 to 0.9 wt% during the preparation of the molecularly imprinted polymer (MIP), thereby varying the thickness of the polymer film; the content of UA as the template was maintained to be the same for all the films. The sensitivities of the thus prepared MIP electrodes were calculated to be more than 3-fold, compared to those of the corresponding non-MIP (NMIP) electrodes, which were obtained through the same method, however, without adding UA during their preparation. A polymer content of 0.6 wt% rendered the best performing MIP electrode, as judged by the imprinting efficiency and sensitivity of the electrode for UA. A linear relationship between steady-state currents and UA concentrations from 0 to 1.125 mM was obtained for both types of the sensors. The sensitivities of the MIP and the NMIP electrodes made with 0.6 wt% of polymer were calculated to be 24.72 and 6.63 μA mM⁻¹ cm⁻², respectively. The limit of detection (LOD) for this MIP was found to be 0.3 μM at a signal to noise ratio (S/N) of 3. This MIP electrode was used as a biosensor for the detection of UA in the presence of ascorbic acid (AA) in a sample containing these species in the same concentrations as those in a human serum. The selectivity of MIP electrode is higher than that of NMIP electrode, and the values are 28.76 and 8.85, respectively. The results are substantiated by using cyclic voltammetry (CV), linear sweep voltammetry, amperometry, and scanning electron microscopy.     

Surface imprinted thin polymer film systems with selective recognition for bovine serum albumin

Molecularly imprinted polymers are synthetic antibody mimics formed by the crosslinking of organic or inorganic polymers in the presence of an analyte which yields recognitive polymer networks with specific binding pockets for that biomolecule. Surface imprinted polymers were synthesized via a novel technique for the specific recognition of bovine serum albumin (BSA). Thin films of recognitive networks based on 2-(dimethylamino)ethyl methacrylate (DMAEMA) as the functional monomer and varying amounts of either N,N′-methylenebisacrylamide (MBA) or poly(ethylene glycol) (400) dimethacrylate (PEG400DMA) as the crosslinking agent were synthesized via UV free-radical polymerization and characterized. A clear and reproducible increase in recognition of the template BSA was demonstrated for these systems at 1.6-2.5 times more BSA recognized by the MIP sample relative to the control polymers. Additionally, these polymers exhibited selective recognition of the template relative to competing proteins with up to 2.9 times more BSA adsorbed than either glucose oxidase or bovine hemoglobin. These synthetic antibody mimics hold significant promise as the next generation of robust recognition elements in a wide range of bioassay and biosensor applications.     

Ordered droplet formation by thin polymer film dewetting on a stripe-patterned substrate

The dewetting process of thin polystyrene (PS) film on flat and stripe-patterned substrates is presented. Different dewetting processes were observed when the thin PS films annealed at above the glass transition temperature on these different kinds of substrates. The final dewetting on the flat substrate led to formation of polygonal liquid droplets, while on the stripe-patterned substrate, the droplets were observed to align at the centers of the stripes. A possible explanation for the dewetting process on the stripe-patterned substrate is proposed.     

An optical reflected device using a molecularly imprinted polymer film sensor

A novel and highly selective optical sensor with molecularly imprinted polymer (MIP) film was fabricated and investigated. The optical sensor head employing a medium finesse molecularly imprinted polymer film has been fabricated and characterised. A blank polymer and formaldehyde imprinted polymer were using methacrylic acid as the functional monomer and the ethylene glycol dimethacrylate as a crosslinker. The transduction mechanism is discussed based on the changes of optical intensity of molecularly imprinted polymer film acting as an optical reflected sensor. Template molecules, which diffused into MIP, could cause film density, and refractive index change, and then induce measurable optical reflective intensity shifts. Based on the reflective intensity shifts, an optical reflection detection of formaldehyde was achieved by illuminating MIP with a laser beam. For the same MIP, the reflective intensity shift was proportional to the amount of template molecule. This optical sensor, based on an artificial recognition system, demonstrates long-time stability and resistance to harsh chemical environments. As the research moves forward gradually, we establish the possibilities of quantitative analysis primly, setting the groundwork to the synthesis of the molecular imprinted optical fiber sensor. The techniques show good reproducibility and sensitivity and will be of significant interest to the MIPcommunity.     

Modulation of direct electron transfer of cytochrome c by use of a molecularly imprinted thin film

We describe the preparation of a molecularly imprinted polymer film (MIP) on top of a self-assembled monolayer (SAM) of mercaptoundecanoic acid (MUA) on gold, where the template cytochrome c (cyt c) participates in direct electron transfer (DET) with the underlying electrode. To enable DET, a non-conductive polymer film is electrodeposited from an aqueous solution of scopoletin and cyt c on to the surface of a gold electrode previously modified with MUA. The electroactive surface concentration of cyt c was 0.5 pmol cm^?2. In the absence of the MUA layer, no cyt c DET was observed and the pseudo-peroxidatic activity of the scopoletin-entrapped protein, assessed via oxidation of Ampliflu red in the presence of hydrogen peroxide, was only 30 % of that for the MIP on MUA. This result indicates that electrostatic adsorption of cyt c by the MUA–SAM substantially increases the surface concentration of cyt c during the electrodeposition step, and is a prerequisite for the productive orientation required for DET. After template removal by treatment with sulfuric acid, rebinding of cyt c to the MUA–MIP-modified electrode occurred with an affinity constant of 100,000 mol^?1 L, a value three times higher than that determined by use of fluorescence titration for the interaction between scopoletin and cyt c in solution. The DET of cyt c in the presence of myoglobin, lysozyme, and bovine serum albumin (BSA) reveals that the MIP layer suppresses the effect of competing proteins.     

The dewetting dynamics of the polymer thin film by solvent annealing

The slippage effect of the polymer chains is investigated in the dewetting process of the polymer solution film. The solvent-induced dewetting is used in our experiments to study the dynamics of hole growth in the dewetting process of the polymer solution film. Our results show that in the case of the low molecular weight polystyrene (PS) film, the slippage effect of the polymer chains is not displayed and the radius of the holes is R approximately exp(t/tau); in the case of the higher molecular weight PS film, the slippage effect of the polymer chain is not valid in the case of the thin film and that is valid in the case of the thick film, and the dynamic process of hole growth divides into three stages (R approximately t, and then R approximately t(x) (23相似文献   

Acetylsalicylic acid electrochemical sensor based on PATP-AuNPs modified molecularly imprinted polymer film

A novel electrochemical sensor based on molecularly imprinted polymer film has been developed for aspirin detection. The sensitive film was prepared by co-polymerization of p-aminothiophenol (p-ATP) and HAuCl(4) on the Au electrode surface. First, p-ATP was self-assembled on the Au electrode surface by the formation of Au-S bonds. Then, the acetylsalicylic acid (ASA) template was assembled onto the monolayer of p-ATP through the hydrogen-bonding interaction between amino group (p-ATP) and oxygen (ASA). Finally, a conductive hybrid membrane was fabricated at the surface of Au electrode by the co-polymerization in the mixing solution containing additional p-ATP, HAuCl(4) and ASA template. Meanwhile, the ASA was spontaneously imprinted into the poly-aminothiophenol gold nanoparticles (PATP-AuNPs) complex film. The amount of imprinted sites at the PATP-AuNPs film significantly increases due to the additional replenishment of ASA templates. With the significant increasing of imprinted sites and doped gold nanoparticles, the sensitivity of the molecular imprinted polymer (MIP) electrode gradually increased. The molecularly imprinted sensor was characterized by electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The linear relationships between current and logarithmic concentration were obtained in the range from 1 nmol L(-1) to 0.1 μmol L(-1) and 0.7 μmol L(-1) to 0.1 mmol L(-1). The detection limit of 0.3 nmol L(-1) was achieved. This molecularly imprinted sensor for the determination of ASA has high sensitivity, good selectivity and reproducibility, with the testing in some biological fluids also has good selectivity and recovery.     

Two-layer model description of polymer thin film dynamics

Experiments in the past two decades have shown that the glass transition temperature of polymer films can become noticeably different from that of the bulk when the film thickness is decreased below ca. 100 nm. It is broadly believed that these observations are caused by a nanometer interfacial layer with dynamics faster or slower than that of the bulk. In this paper, we examine how this idea may be realized by using a two-layer model assuming a hydrodynamic coupling between the interfacial layer and the remaining, bulk-like layer in the film. Illustrative examples will be given showing how the two-layer model is applied to the viscosity measurements of polystyrene and polymethylmethacrylate films supported by silicon oxide, where divergent thickness dependences are observed.     

Highly oriented tunable wrinkling in polymer bilayer films confined with a soft mold induced by water vapor

The authors report the formation of highly oriented wrinkling on the surface of the bilayer [polystyrene (PS)/poly(vinyl pyrrolidone) (PVP)] confined by a polydimethylsiloxane (PDMS) mold in a water vapor environment. When PVP is subjected to water vapor, the polymer loses its mechanical rigidity and changes to a viscous state, which leads to a dramatic change in Young's modulus. This change generates the amount of strain in the bilayer to induce the wrinkling. With a shape-controlled mold, they can get the ordered wrinkles perfectly perpendicular or leaned 45 degrees to the channel orientation of the mold because the orientation of the resultant force changes with the process of water diffusion which drives the surface to form the wrinkling. Additionally, they can get much smaller wrinkles than the stripe spacing of PDMS mold about one order. The wrinkle period changes with the power index of about 0.5 for various values of the multiplication product of the film thicknesses of the two layers, namely, lambda approximately (h(PS)h(PVP))(1/2).     

Binding efficiency and transport properties of molecularly imprinted polymer thin films

A model system for the characterization of molecular recognition events in molecularly imprinted polymers (MIPs) is presented. The use of a biologically inspired, three-point hydrogen-bonding motif and a thin film polymeric matrix allows for pre- and post-polymerization binding properties to be characterized by infrared spectroscopy. A method to determine binding constants was developed and utilized before and after cross-linking. These values showed a 10-fold decrease in binding after polymerization, which was attributed to an increase in molecular confinement after polymerization and a change in the local structural environment of the binding cavity. Transport of the guest molecule was shown to be reversible.     

Formation of thin carbon films containing metal nanoparticles by thermolysis of a polymer precursor

A new procedure was developed for preparing carbon films with magnetic metal nanoparticles by thermolysis of a polymer precursor. The conditions for preparing carbon films with required surface concentration of the metal nanoparticles and hence with dielectric or metallic properties were determined.     

Enantioselective sensor based on microgravimetric quartz crystal microbalance with molecularly imprinted polymer film

We report a novel quartz crystal microbalance sensor that provides enantioselectivity to dansylphenylalanine enantiomers by using a molecularly imprinted polymer film as a recognition element. The polymeric recognition thin film, imprinted with chiral dansyl-L-phenylalanine, was immobilised on a gold electrode modified with a photoactive precursor monolayer via a self-assembly process using photopolymerization. The fabricated sensor was able to discriminate between L- and D-dansylphenylalanine enantiomers in solution owing to the enantioselectivity of the imprinted sites. The enantiomeric composition of L- and D-enantiomeric mixtures could be quantitatively determined by the fabricated sensor. The detection limit is 5 micrograms mL-1 with a response range of 5-500 micrograms mL-1 at pH 10.0. The influence of the template concentration on the sensitivity and selectivity of the synthesised polymer membranes was investigated and optimised. The surface characteristics of the polymer coating were studied by varying the pH value of the buffer solution, and a convenient regeneration process was proposed to increase the reproducibility and reusability of the sensor by flushing with pH 2.0 buffer. The selectivity and recognition mechanism of the imprinted polymer film were studied with compounds that are structurally related to the template. The method presented in this work provides a novel means of preparing highly selective and sensitive chemical sensors via self-assembly and molecularly imprinting techniques.     

Electrochemical sensor for acetaminophen based on an imprinted TiO2 thin film prepared by liquid phase deposition

An electrochemical sensor based on a molecularly imprinted TiO₂ thin film is proposed for the determination of acetaminophen. The imprinted TiO₂ films were obtained by liquid phase deposition (LPD) in the presence of acetaminophen, the functional monomer and the aqueous solution of (NH₄)₂TiF₆ and H₃BO₃. The results show that acetaminophen is embedded into the imprinted film in the presence of p-tert-butylcalix[6]arene as a functional monomer, and can be removed completely by washing with ethanol. The surface morphology, spectral properties and electrochemical characterizations of the imprinted sensor were investigated in detail. The combination of molecularly imprinted and LPD technique was shown to be a general strategy for constructing a molecular recognition system.     

Formation and dielectric properties of polyelectrolyte multilayers studied by a silicon-on-insulator based thin film resistor

The formation of polyelectrolyte multilayers (PEMs) is investigated using a silicon-on-insulator based thin film resistor which is sensitive to variations of the surface potential. The buildup of the PEMs at the silicon oxide surface of the device can be observed in real time as defined potential shifts. The influence of polymer charge density is studied using the strong polyanion poly(styrene sulfonate), PSS, combined with the statistical copolymer poly(diallyl-dimethyl-ammoniumchloride-stat-N-methyl-N-vinylacetamide), P(DADMAC-stat-NMVA), at various degrees of charge (DC). The multilayer formation stops after a few deposition steps for a DC below 75%. We show that the threshold of surface charge compensation corresponds to the threshold of multilayer formation. However, no reversion of the preceding surface charge was observed. Screening of polyelectrolyte charges by mobile ions within the polymer film leads to a decrease of the potential shifts with the number of layers deposited. This decrease is much slower for PEMs consisting of P(DADMAC-stat-NMVA) and PSS as compared to PEMs consisting of poly(allylamine-hydrochloride), PAH, and PSS. From this, significant differences in the dielectric constants of the polyelectrolyte films and in the concentration of mobile ions within the films can be derived.     

Molecularly imprinted TiO2 thin film by liquid phase deposition for the determination of L-glutamic acid

For the first time, the feasibility of a molecularly imprinted liquid phase deposition (LPD) thin film has been demonstrated. Thin films of titanium oxide imprinted with L-glutamic acid were prepared by the LPD method on a gold-coated quartz crystal microbalance. The imprinted molecule could be removed upon treatment with immersion in deionized water. A sensor was developed on the basis of this method and showed good sensitivity, selectivity, and reproducibility to the template molecule. An equation was deduced to characterize the interaction between molecularly imprinted films and the template by virtue of Scatchard analysis. X-ray photoelectron spectroscopy was introduced to show the evidence for the molecular imprinting phenomenon. The linear relationship between the frequency shifts and the concentration of analyte in the range of 10-200 microM was obtained. LPD proves to be a powerful method for imprinting titanium oxide thin films.     

The influence of nanoparticle fillers on the morphology of a spin-cast thin film polymer blend

Polymer/nanoparticle composite films are receiving growing attention thanks to their potential for application in ultra-thin electronic and optical devices. Polymer blend demixing has been shown to be a suitable technique for the structuring of polymer thin films and the patterning of nanoparticles (NP) within them. In this work we show that the morphology of thin polymer films made by spin-casting a polymer blend solution containing NP fillers on a surface depends strongly on the concentration of NP fillers. More specifically, polystyrene/polymethylmethacrylate (PS/PMMA) films formed from a toluene solution, and which demix following a nucleation and growth mechanism, were studied. It was found that both the height and the surface density of PMMA domains increased as the concentration of CoPt:Cu NPs in the film was increased. We find that similar effects are induced in a NP-free PS/PMMA demixed film upon increasing the molecular weight of the PS molecules. This suggests that under certain conditions the NPs and the polymer molecules in the blend do not behave as separate species but form aggregates.     

Novel electrical properties of nanoscale thin films of a semiconducting polymer: quantitative current-sensing AFM analysis

Thin films (20-150 nm thickness) of poly(o-anthranilic acid) with various doping levels were prepared on silicon substrates with deposited indium tin oxide, and their topography and current-voltage (I-V) characteristics were quantitatively investigated using current-sensing atomic force microscopy with a platinum-coated tip. The films were found to have a surface morphology like that of orange peel, with a periodic modulation and a surface roughness. The films exhibited nonuniform current flows and I-V characteristics that depended on the doping level as well as on the film thickness. Films with a high doping level were found to exhibit Zener diode switching behavior, whereas the films with a very low doping level (or that were dedoped) exhibited no current flow at all, and so are insulators. Interestingly, self-doped films (which are at an intermediate doping level) were found to have a novel electrical bistability, i.e., a switching characteristic like that of Schottky diodes, and increasingly insulating characteristics as the film thickness was increased. The films with thickness < or =62 nm, which exhibited this novel and stable electrical bistability, can potentially be used in the fabrication of high-density, stable, high-performance digital nonvolatile memory devices based only on transistors. The measured current images and I-V characteristics indicate that the electrical switching and bistability of the films are governed by local filament formation and charge traps.