Development of two-port surface acoustic wave resonator with Al/Au electrodes for gas sensing

Simple and efficient surface acoustic wave(SAW)two-port resonators with low insertion loss and high Q-values on ST-X quartz substrate using a corrosion-proof A1/Au-stripe electrode structure are developed for gas sensing.It was composed of two shorted grating reflectors and adjacent intedigital transducers(IDT),and an active metal film in the cavity between the IDTs for the sensitive film coating.The devices are expected to provide good protection towards metal electrode for gas sensors application in chemically reactive environments.Excellent device performance as low insertion loss,high Q factor and single-mode are achieved by carefully selecting the metallic electrode thickness,cavity length and acoustic aperture.Prior to fabrication,the coupling of modes(COM)model was performed for device simulation to determine the optimal design parameters.The fabricated single-mode SAW resonator at operation frequency of 300 MHz range exhibits matched insertion loss of~6.5 dB and loaded Q factor in the 3000 range.Using the fabricated resonator as the feedback element,a dualresonator-oscillator with excellent frequency stability(0.1 ppm)was developed and evaluated experimentally,and it is significant for performance improvement of SAW gas sensor.     

应用于气体传感器的具有铝/金电极的单模式两端对声表面波谐振器

为改善气体传感器性能,通过器件优化设计获得了一种应用于气体传感器的具有低损耗、高品质因子(Q)的单模式两端对声表面波(SAW)谐振器。该谐振器由两个换能器、分置于换能器两边的短路栅反射器以及在换能器之间分布的用于敏感膜镀膜的约2.5mm金属薄层构成。谐振器采用铝/金双层电极以降低测试气体环境的腐蚀影响。利用经典耦合模(COM)理论对器件性能进行了仿真以提取优化的结构设计参数。基于仿真结果,实验研制了基于300MHz频率的新型铝/金电极SAW两端对谐振器,测试结果显示所研制器件具有较低损耗(〈7dB),较高Q值(-3000)以及单一谐振模式的特点,并且,以所研制的新型谐振器为频率控制单元的谐振器型振荡器表现出良好的频率稳定度(t15Hz/h),这对于改善气体传感器的检测下限及稳定性等性能指标具有重要意义。     

evelopment of two-port surface acoustic wave resonator with A1/Au electrodes for gas sensing

Simple and efficient surface acoustic wave （SAW） two-port resonators with low insertion loss and high Q-values on ST-X quartz substrate using a corrosion-proof A1/Au-stripe electrode structure are developed for gas sensing. It was composed of two shorted grating reflectors and adjacent intedigital transducers （IDT）, and an active metal film in the cavity between the IDTs for the sensitive film coating. The devices are expected to provide good protection towards metal electrode for gas sensors application in chemically reactive environments. Excellent device performance as low insertion loss, high Q factor and single-mode are achieved by carefully selecting the metallic electrode thickness, cavity length and acoustic aperture. Prior to fabrication, the coupling of modes （COM） model was performed for device simulation to determine the optimal design parameters. The fabricated single-mode SAW resonator at operation frequency of 300 MHz range exhibits matched insertion loss of ~6.5 dB and loaded Q factor in the 3000 range. Using the fabricated resonator as the feedback element, a duaresonator-oscillator with excellent frequency stability （0.1 ppm） was developed and evaluated experimentally, and it is significant for performance improvement of SAW gas sensor.     

高频沟槽叉指体声波换能器

本文介绍了一种由压电晶体沟槽表面上的叉指换能器构成的新型体声波换能器。制作在X切LiNbO₃,表面的横波换能器在213MHz时的一次换能损耗为3.8dB。     

Nonlinear compression of giant surface acoustic wave pulses

The nonlinear propagation of very high-amplitude surface acoustic wave (SAW) pulses in polycrystalline aluminum and copper was studied. A nonlinear compression and an increase of the SAW pulse amplitude have been observed. SAW pulses were numerically simulated with a nonlinear evolution equation including local and nonlocal nonlinear terms.     

谐振式检测器谐振腔对声表面波气相色谱仪灵敏度的影响

研究了谐振式检测器谐振腔对声表面波气相色谱仪灵敏度的影响。构建无液膜负载和有液膜负载下压电基片和金属指条结构的三维有限元模型,利用有限元方法提取不同周期结构的耦合模参量,结合P矩阵级联技术,推导出传感器灵敏度随检测器腔体结构改变的变化关系。实验制备了两种三换能器结构的声表面波谐振器,其输入换能器与输出换能器间距离分别为22.25倍波长和1.25倍波长,通过测试甲基膦酸二甲酯气体,验证理论计算结果。结果表明:缩短谐振器的谐振腔长度使器件中心处能量更为集中,有效地提高了声表面波气相色谱仪灵敏度。     

一种高灵敏度的桥型声表面波应变传感器

为了提高声表面波传感器应变灵敏度,该文提出了一种桥型声表面波应变传感器.首先根据受压弯曲构件中应变分布特点设计了桥型声表面波应变传感器,并建立有限元模型,结合微扰法分析了桥型结构几何参数与声表面波应变传感器灵敏度的关系.根据分析结果确定桥型声表面波应变传感器几何结构参数,并与传统声表面波应变传感器的应变灵敏度进行了对比...     

Laser-generated surface acoustic waves in a ring-shaped waveguide resonator

Surface acoustic wave (SAW) waveguide resonator is formed by a ring-shaped strip of copper 10 μm wide and ∼130 μm in diameter embedded into a 0.8 μm thick layer of silica on a silicon wafer. SAWs are excited at one side of the copper ring by a short laser pulse focused into a spatially periodic pattern and detected via diffraction of the probe laser beam overlapped with the excitation spot. SAW wavepackets with central frequency 460 MHz travel around the ring and are detected each time they make a full circle and pass trough the probe spot. Potential applications of ring resonators for SAWs are discussed.     

Nonlinear parameter estimation in water-saturated sandy sediment with difference frequency acoustic wave

Difference frequency acoustic wave from nonlinear interaction of two primary acoustic waves at frequencies of 76 and 114 kHz was utilized with a parametric acoustic array theory to estimate the nonlinearity parameter of water-saturated sandy sediment. Such nonlinearity parameter can be used as background information for the nonlinear acoustic investigation of bottom or sub-bottom profiling in the ocean sandy sediments. Because of its lower attenuation the difference frequency acoustic wave method can be usefully applied to estimate the nonlinearity parameter of ocean sediment in the ocean as well as under laboratory conditions. The nonlinearity parameter β for the water-saturated sandy sediment used as a reference in this study was estimated as β = 80.5 ± 5.1 at the difference frequency of 38 kHz. It was agreed very well with that estimated at the difference frequency of 67 kHz, when two primary frequencies were 137 and 204 kHz. The estimated nonlinearity parameter of water-saturated sandy sediment in this study was also compared and analyzed with those estimated in previously published literatures. It was suggested that the difference frequency wave method used to estimate the nonlinearity parameter of water-saturated sandy sediment can be employed as a good method to estimate the nonlinearity parameters of fluid-like granular media.     

声表面波气体传感器研究进展*

基于声表面波技术的气体传感器包括采用敏感膜和结合气相色谱两种方式。比较而言,采用敏感膜的声表面波气体传感器体积小、功耗低,适应小型化毒气报警器的发展要求,但可检测的气体种类少、灵敏度低、存在交叉干扰问题;声表面波与气相色谱联用的气体分析仪灵敏度高、可检测气体种类多、很好地解决交叉干扰问题,特别适合于复杂大气背景条件下的气体成分分析。本文从传感器响应机理分析与物理功能结构两方面出发介绍了两类声表面波气体传感器的研究进展情况。     

Nonlinear acoustic wave generation in a three-phase seabed

Generation of an acoustic wave by two pump sound waves is studied in a three-phase marine sediment, which consists of a solid frame and the pore water with air bubbles in it. To avoid shock-wave formation, the interaction is considered in the frequency range where there is a significant sound velocity dispersion. Nonlinear equations are obtained to describe the interaction of acoustic waves in the presence of air bubbles. An expression for the amplitude of the generated wave is obtained and numerical analysis of its dependence on distance and resonance frequency of bubbles is performed.     

Nonlinear acoustic effects in a resonator with saturation of hysteretic loss

Nonlinear wave processes in an acoustic rod resonator with hysteretic nonlinearity under harmonic excitation are studied. The characteristics of longitudinal nonlinear modes of the resonator with hard and soft boundaries (amplitude-dependent loss, shifts of resonance frequencies, and amplitudes of the second and third harmonics) are determined. The comparison of the theoretical and experimental dependences of nonlinear acoustic effects in a resonator that is made of annealed polycrystalline copper is used to determine the parameters of the hysteretic nonlinearity.     

Spin pumping in a composite high overtone bulk acoustic wave resonator

A new way of generating a pure spin current using a magnetoelectric composite high-overtone bulk acoustic-wave resonator (HBAR) based on a layered Al–ZnO–Al–Gd₃Ga₅O₁₂–Y₃Fe₅O₁₂–Pt structure is proposed. It is established that the efficiency of generating the rf magnetic field driving the spin current by this method exceeds that of sources which use surface acoustic waves for the excitation of magnetic dynamics and is not inferior to the efficiency of usual electromagnetic ways of exciting a pure spin current that employ microwave cavities.     

声表面波器件变频快速模拟方法

声表面波器件的级联有限元模拟方法是从整体结构中分离出若干独立的基本单元,通过基本单元边界矩阵的级联实现有限长器件结构的模拟.在实际设计中,通过优化叉指换能器的指条周期,激发出不同波长的声表面波,调整声表面波器件的谐振频率,这导致级联有限元模拟方法存在频繁的单元建模与数据传输过程.为提高模拟效率,该文提出了一种波长(频率...     

Nonlinear stationary acoustic wave in a solid with dislocations

It is shown that a nonlinear stationary acoustic wave can be formed in a solid with dislocations. Such a wave is periodic and moves faster than acoustic signals in a linear medium. The wave has a saw-tooth shape and its wavelength increases with the amplitude.     

基于AlN声表面波滤波传感器器件的有限元仿真

声表面波器件是一种利用压电材料的压电效应与逆压电效应工作电子器件, 文章首先详细描述了声表面波器件的设计与仿真过程,运用有限元分析的方法分别计算了利用声表面波的 SAW 器件与利用体波的 BAW 器件的性能与各项参数,对相关的器件进行了计算分析,分别用上述方法研究了基于 AlN 薄膜的声表面波器件和悬臂梁结构的体波器件,推导得出了器件的电学导纳与频率之间的关系, 通过分析器件的导纳-频率曲线,推导出器件内部声波的模式以及合适的工作频率,最终得出在 IDT 周期为 8 微米的情况下,SAW 器件的理想工作频率是 0.7-1.95GHz,BAW 器件的理想工作频率在 0.6-3.2GHz 的结果。     

Development of a surface acoustic wave wireless and passive temperature sensor incorporating reflective delay line

based on optimal design on the core element of the sensor,a wireless and passive surface acoustic wave(SAW)temperature sensor integrated with ID Tag was presented.A reflective delay line,which consists of a transducer and eight reflectors on YZ LiNbO3 substrate.Was fabricated as the sensor element,in which,three reflectors were used for temperature sensing,and the other five were for the ID Tag using phase encoding.Single phase unidirectional transducers(SPUDTs)and shorted grating were used to structure the sAW device,leading to excellent signal to noise ratio(SNR).The performance of the SAW device was simulated by the coupling of modes(COM)prior to fabrication.Using the network analyzer,the response in time domain of the fabricated 434 MHz SAW sensor was characterized,the measured S11 agrees well with the simulated one,sharp reflection peaks,high signal/noise,and low spurious noise between the reflection peaks were observed.Using the radar system based on FSCW as the reader unit.the developed SAW temperature sensors were evaluated wirelessly.Excellent1 inearity and good resolution of士1℃ were observed.