Effect of disturbances at inlet on hypersonic boundary layer transition on a blunt cone at small angle of attack

To investigate the effect of different disturbances in the upstream, we present numerical simulation of transition for a hypersonic boundary layer on a 5-degree half-angle blunt cone in a freestream with Mach number 6 at 1-degree angle of attack. Evolution of small disturbances is simulated to compare with the linear stability theory （LST）, indicating that LST can provide a good prediction on the growth rate of the disturbance. The effect of different disturbances on transition is investigated. Transition onset distributions along the azimuthal direction are obtained with two groups of disturbances of different frequencies. It shows that transition onset is relevant to frequencies and amplitudes of the disturbances at the inlet, and is decided by the amplitudes of most unstable waves at the inlet. According to the characteristics of environmental disturbances in most wind tunnels, we explain why transition occurs leeside-forward and windside-aft over a circular cone at an angle of attack. Moreover, the indentation phenomenon in the transition curve on the leeward is also revealed.     

Numerical modeling of laminar-turbulent transition in a boundary layer at a high freestream turbulence level

Disturbances generated by external turbulence in the boundary layer on a flat plate set suddenly in motion are determined by numerically solving the Navier-Stokes equations. The results of direct numerical simulation of isotropic homogenous turbulence are taken as initial conditions. The solution obtained models laminar-turbulent transition in the flat-plate boundary layer at a high freestream turbulence level, time measured from the onset of the motion serving as the longitudinal coordinate. The solution makes it possible to estimate the effect of different factors, such as flow unsteadiness and nonlinearity and the characteristics of the freestream velocity fluctuation spectrum, on laminar-turbulent transition in the boundary layer.     

Asymptotic solution of the thin viscous shock layer equations at low Reynolds numbers for a cold surface

Hypersonic three-dimensional viscous rarefied gas flow past blunt bodies in the neighborhood of the stagnation line is considered. The question of the applicability of the gasdynamic thin viscous shock layer model [1] is investigated for the transition flow regime from continuum to free-molecular flow. It is shown that for a power-law temperature dependence of the viscosity coefficient T the quantity (Re)^1/(1+), where = ( – 1)/2 and is the specific heat ratio, is an important determining parameter of the hypersonic flow at low Reynolds numbers. In the case of a cold surface approximate asymptotic solutions of the thin viscous shock layer equations are obtained for noslip conditions on the surface and generalized Rankine-Hugoniot relations on the shock wave at low Reynolds numbers. These solutions give simple analytic expressions for the thermal conductivity and friction coefficients as functions of the determining flow parameters. As the Reynolds number tends to zero, the values of the thermal conductivity and friction coefficients determined by this solution tend to their values in free-molecular flow for an accommodation coefficient equal to unity. This tending of the thermal conductivity and friction coefficients to the free-molecular limit takes place for both two-and three-dimensional flows. The asymptotic solutions are compared with numerical calculations and experimental data.Translated from Izvestiya Rossiiskoi Academii Nauk, Mekhanika Zhidkosti i Gaza, No. 5, 2004, pp. 159–170. Original Russian Text Copyright © 2004 by Brykina.     

Prediction of hypersonic boundary layer transition on sharp wedge flow considering variable specific heat

When the air temperature reaches 600 K or higher, vibration is excited. The specific heat is not a constant but a function of temperature. Under this condition, the transition position of hypersonic sharp wedge boundary layer is predicted by using the improved eN method considering variable specific heat. The transition positions with different Mach numbers of oncoming flow, half wedge angles, and wall conditions are computed condition, the nearer to the Mach number The results show that for the same oncoming flow condition and wall transition positions of hypersonic sharp wedge boundary layer move much leading edge than those of the flat plate. The greater the oncoming flow the closer the transition position to the leading edge.     

Laminar-turbulent flow over wedges mounted on sharp and blunt plates

The flow pattern and the heat transfer on sharp and blunt flat plates near a wedge in a Mach 6 stream are experimentally investigated for two Reynolds numbers corresponding to the laminar and transitional states of the undisturbed boundary layer ahead of the wedge. It is shown that, as in a two-dimensional flow, plate bluntness leads to the attenuation of the heat transfer in the boundary layer/shock wave interference zone. However, when a certain threshold value of the bluntness is exceeded, a further increase in the bluntness has almost no effect on the heat transfer. For the first time, an experiment conducted in an intermittent (blow-down) wind tunnel has been based on the comprehensive use of panoramic (global) techniques for measuring the heat transfer and pressure coefficients and a method for visualizing the surface friction employing the luminescence effect after UV irradiation.     

Theoretical analysis of acoustic instability of a hypersonic shock layer on a porous wall

The possibility of controlling the laminar-turbulent transition in hypersonic shock layers by means of porous coatings is considered. The linear stability of the shock layer to acoustic disturbances is analyzed. A dispersion relation is derived in an analytical form and analyzed for different characteristic values of porosity of the wall, which allows one to study the spectrum of acoustic disturbances in the shock layer. Analytical expressions for the growth rate of instability of acoustic disturbances are presented as functions of the reflection factor. Their structure indicates that the porous coating effectively decreases acoustic instability of the shock layer.Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 1, pp. 44–54, January–February, 2005.     

Numerical solutions of 2‐D steady incompressible driven cavity flow at high Reynolds numbers

Numerical calculations of the 2‐D steady incompressible driven cavity flow are presented. The Navier–Stokes equations in streamfunction and vorticity formulation are solved numerically using a fine uniform grid mesh of 601 × 601. The steady driven cavity flow solutions are computed for Re ? 21 000 with a maximum absolute residuals of the governing equations that were less than 10^?10. A new quaternary vortex at the bottom left corner and a new tertiary vortex at the top left corner of the cavity are observed in the flow field as the Reynolds number increases. Detailed results are presented and comparisons are made with benchmark solutions found in the literature. Copyright © 2005 John Wiley & Sons, Ltd.     

Study of the aerodynamic characteristics of cone-sphere models in a hypersonic flow

The aerodynamic characteristics of cone-sphere models are studied at Mach numbers M = 6, 8.4, and 12 to 13 over a wide Reynolds number range. Models of a braking device (sphere) were connected with a load (frustum of a cone) by means of shrouds. The dependences of the aerodynamic coefficients C _x and C _y on the angle of attack α were obtained for different relative dimensions of the load and the braking device, shroud lengths, and Mach and Reynolds numbers. The effect of the above-mentioned parameters on the aerodynamic characteristics of the models is analyzed. The C _x (Re_D) dependences of load-parachutemodels in a symmetric flow are determined over the wide Mach and Reynolds number ranges 6 ≤ M ≤ 13 and 3 · 10³ ≤ Re_D ≤ 3 · 10⁶.     

Forces on a spherical particle in shear flow at intermediate Reynolds numbers

When particles are submerged in a shear flow, there are lateral (lift) forces on the particles, and these lateral forces affect the dispersion of the particles very much. Recent literature survey indicates that there are large discrepancies among the results from the previous numerical investigations on this subject. A small computational domain ranging between 20–30 sphere radii was used in all the previous numerical investigations. However, the result from the present study reveals that the value of lift coefficient strongly depends on the size of computational domain. To provide correct numerical data and physical interpretation for the forces on a spherical particle in linear shear flow, accurate numerical computations were performed for 5≤Re≤200 using a computational domain of 101 sphere radii.     

Asymptotic analysis of turbulent boundary layer flow on a flat plate at high Reynolds numbers

The equations of the turbulent boundary layer contain a small parameter — the reciprocal of the Reynolds number, which makes it possible to carry out an asymptotic analysis of the solutions with respect to that small parameter. Such analyses have been the subject of a number of studies [1–5]. In [2, 5] for closing the momentum equation algebraic Prandtl and turbulent viscosity models were used. In [1, 3, 4] the structure of the boundary layer was analyzed in general form without formulating specific closing hypothesis but under additional assumptions concerning the nature of the asymptotic behavior of the limiting solutions in the various regions.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.4, pp. 106–117, May-June, 1993.     

Mechanism of transition in a hypersonic sharp cone boundary layer with zero angle of attack

Firstly, the steady laminar flow field of a hypersonic sharp cone boundary layer with zero angle of attack was computed.Then,two groups of finite amplitude T-S wave disturbances were introduced at the entrance of the computational field,and the spatial mode transition process was studied by direct numerical simulation (DNS) method. The mechanism of the transition process was analyzed.It was found that the change of the stability characteristics of the mean flow profile was the key issue.Furthermore,the characteristics of evolution for the disturbances of different modes in the hypersonic sharp cone boundary layer were discussed.     

An experimental study of the dynamic characteristics in boundary layer in the flow past a two-dimensional circular cylinder at subcritical reynolds numbers

An experimental study of the dynamic characteristics of flow past a two-dimensional circular cylinder is described. The fluctuationsoof wall shear stress, surface-pressure and velocity of the flow are measured with hot-film, hot-wire and pressure transducer. The frequency feature of fluctuations of wall shear stress is given. The cross-correlation functions of these fluctuations at any two points are calculated. The experimental results reveal that there is an overall syncronous fluctuation, at the shedding frequency, in boundary layer in the flow past a two-dimensional circular cylinder at subcritical Reynolds number.     

Relaxation processes in hypersonic rarefied binary gas mixture flow around a cylinder

Using the direct simulation Monte Carlo method, the hypersonic flow of a binary gas mixture around a cylinder is investigated over a wide rarefaction range: from an almost continuum regime (at the Knudsen number Kn = 0.01) to free-molecular flow. The effect of a small admixture of heavy diatomic particles in a light gas flow on the relaxation processes near the cylinder and the heat flux is studied.     

Laminar boundary layer separation at a fin-body junction in a hypersonic flow

Planar laser-induced fluorescence (PLIF) imaging was performed to visualize the fin bow shock, separation shock, viscous shear layer and recirculation region of the flowfield at the junction of a blunt fin and a flat plate. Making use of the temperature dependence of the PLIF technique, images were made sensitive to temperature to provide qualitative information on the flowfield. The PLIF technique was also used as the basis for a flow-tagging technique, making it possible to measure a velocity component and to demonstrate the reverse flow of the separated region. Flow visualisation of the plane of symmetry allowed determination of the point of boundary layer separation, the angle of the separation shock and the bow shock standoff distance. These parameters were compared with predictions made by computational fluid dynamic simulations of the flowfield. Good agreement between theory and experiment was achieved. Comparisons between theoretical and experimental velocity measurements showed good agreement. Received 17 October 2000 / Accepted 13 November 2000     

A three-dimensional simulation of a steady approach flow past a circular cylinder at low Reynolds number

The three-dimensional (3D) unsteady viscous wake of a circular cylinder exposed to a steady approach flow is calculated using a fractional-step finite-difference/spectral-element method. The calculated flow fields at Reynolds numbers of 100 (2D) and 200 (3D) are examined in detail. The flow field at Re = 100 is 2D as expected, while the flow field at Re = 200 has distinct 3D features, with spanwise wavelengths of about 3.75 cylinder diameters. The calculated results produce drag and lift coefficients and Strouhal numbers that agree extremely well with the experimental values. These 3D values at Re = 200 are in better agreement with experimental values than the results of a 2D calculation at Re = 200, which is expected. © 1998 John Wiley & Sons, Ltd.     

Effect of the freestream turbulence scale and the leading edge shape on boundary layer laminar-turbulent transition

The effect of the leading edge shape and the turbulence scale on laminar-turbulent transition in the flat-plate boundary layer due to grid turbulence is investigated. In the experiments, the turbulence scale was changed by a factor of three and the bluntness radius of the edge by a factor of four, all other factors being fixed. It is shown that on the plate with a sharp edge the fluctuation growth rate and the laminar-turbulent transition point depend nonmonotonically on the turbulence scale. On the blunt plate transition occurs considerably earlier than on the sharp plate.     

Development of slow disturbances in a hypersonic boundary layer

The mechanisms of development of slow time-dependent disturbances in the wall region of a hypersonic boundary layer are established and a diagram of the disturbed flow patterns is plotted; the corresponding nonlinear boundary value problem is formulated for each of these regimes. It is shown that the main factors that form the disturbed flow are the gas enthalpy near the body surface, the local viscous-inviscid interaction level, and the type, either subsonic or supersonic, of the boundary layer as a whole. Numerical and analytical solutions are obtained in the linear approximation. It is established that enhancement of the local viscous-inviscid interaction or an increased role for the main supersonic region of the boundary layer makes the disturbed flow by and large “supersonic”: the upstream propagation of the disturbances becomes weaker, while their downstream growth is amplified. Contrariwise, local viscous-inviscid interaction attenuation or an increased role for the main subsonic region of the boundary layer has the opposite effect. Surface cooling favors an increased effect of the main region of the boundary layer while heating favors an increased wall region effect. It is also found that in the regimes considered disturbances travel from the turbulent flow region downstream of the disturbed region under consideration counter to the oncoming flow, which may be of considerable significance in constructing the nonlinear stability theory.     

Regime diagram of the development of long-wave near-wall disturbances in a hypersonic boundary layer

A regime diagram of the development of slow near-wall disturbances induced by an unsteady self-induced pressure perturbation in a hypersonic boundary layer is constructed for a disturbance wavelength greater than the boundary layer thickness. It is shown that the main factors shaping the perturbed flow are the gas enthalpy near the body surface, the intensity of the viscous-inviscid interaction, and the nature (sub- or supersonic) of the main part of the boundary layer. Nonlinear boundary-value problems are formulated for regimes in which the near-wall boundary layer region plays a decisive role. Numerical and analytical solutions are obtained in the linear approximation. It is shown that intensification of the viscous-inviscid interaction or an increase in the role of the supersonic main region of the boundary layer impart generally supersonic properties to the main part of the boundary layer, i.e. the upstream propagation of the disturbances is damped and the disturbance growth downstream becomes more intense. Damping of the viscous-inviscid interaction and an increase in the role of the subsonic main part of the boundary layer have the opposite effect. Surface cooling increases the effect of the main part of the boundary layer on the formation of pressure disturbances and surface heating leads to an increase in the effect of the near-wall boundary layer region. It is also shown that for the regimes considered disturbances propagate in a direction opposite to that of the free stream from the turbulent flow region located downstream of the local disturbance development region.Translated from Izvestiya Rossiiskoi Academii Nauk, Mekhanika Zhidkosti i Gaza, No. 6, 2004, pp. 59–71. Original Russian Text Copyright © 2004 by Bogolepov and Neiland.     

Stability analysis and transition prediction of hypersonic boundary layer over a blunt cone with small nose bluntness at zero angle of attack

Stability and transition prediction of hypersonic boundary layer on a blunt cone with small nose bluntness at zero angle of attack was investigated. The nose radius of the cone is 0.5 mm; the cone half-angle is 5°, and the Mach number of the oncoming flow is 6. The base flow of the blunt cone was obtained by direct numerical simulation. The linear stability theory was applied for the analysis of the first mode and the second mode unstable waves under both isothermal and adiabatic wall condition, and eN method was used for the prediction of transition location. The N factor was tentatively taken as 10, as no experimentally confirmed value was available. It is found that the wall temperature condition has a great effect on the transition location. For adiabatic wall, transition would take place more rearward than those for isothermal wall. And despite that for high Mach number flows, the maximum amplification rate of the second mode wave is far bigger than the maximum amplification rate of the first mode wave, the transition location of the boundary layer with adiabatic wall is controlled by the growth of first mode unstable waves. The methods employed in this paper are expected to be also applicable to the transition prediction for the three dimensional boundary layers on cones with angle of attack.