SOA-based actively mode-locked fiber ring laser by forward injecting an external pulse train

An actively mode-locked fiber ring laser based on cross-gain modulation (XGM) in a semiconductor optical amplifier (SOA) is demonstrated to operate stably with a simple configuration. By forward injecting an easily-generated external pulse train, the mode-locked fiber laser can generate an optical-pulse sequence with pulsewidth about 6 ps and average output power about 7.9 mW. The output pulses show an ultra-low RMS jitter about 70.7 fs measured by a RF spectrum analyzer. The use of the proposed forward-injection configuration can realize the repetition-rate tunability from 1 to 15 GHz for the generated optical-pulse sequences. By employing a wavelength-tunable optical band-pass filter in the laser cavity, the operation wavelength of the designed SOA-based actively mode-locked fiber laser can be tuned continuously in a wide span between 1528 and 1565 nm. The parameters of external-injection optical pulses are studied experimentally to optimize the mode-locked fiber laser.     

Efficient, kHz repetition rate, gain-switched Cr:forsterite laser

We have developed a gain-switched room-temperature Cr:forsterite laser operating at repetition rates of between 1 and 34 kHz, and pumped by a continuous wave, Q-switched Nd:YAG laser. With optimised output coupling, an output pulse energy of 52 μJ was measured at 1.5 kHz repetition rate, corresponding to 11% efficiency and 13% slope efficiency. Threshold pulse energy was 53 μJ. Output power of 370 mW was obtained at 10 kHz repetition rate and 4.4 W pump power. Water cooling was not required for repetition rates up to 10 kHz. In a tunable, folded resonator, the Cr:forsterite wavelength tuned between 1173 and 1338 nm. This laser operated with maximum pulse energy of 34 μJ, efficiency of 13%, and power of 307 mW. The laser output was close to diffraction-limited with M² of 1.2. Received: 6 January 1999 / Published online: 29 July 1999     

分布反馈激光特性的实验研究

研究了以脉冲YAG倍频激光泵浦Rh6G染料,产生分布反馈激光振荡的辐射光谱、转换效率、时间过程以及可调谐特性;发现在大于泵浦阈值下的分布反馈激光输出的多谱线结构与双脉冲辐射现象,以及分布反馈激光脉冲变窄的自开关效应.作为详细的实验观察和分析.     

Copper-vapour laser with silver additive

Results of experimental investigation of a pure elemental copper-vapour laser with silver additive are reported. Average output power as well laser output pulse energy increased by up to 10% with the additive. A possible mechanism of additive influence on laser output parameters is discussed.     

Picosecond and subpicosecon pulse generation in synchronously pumped mode-locked cw dye lasers

Generation of tunable near-infrared picosecond and subpicosecond pulses in a synchronously pumped cw mode-locked Oxazine-1-perchlorate dye laser has been investigated for different values of the important system parameters. The experimental results confirm the predictions of a simple theoretical model which describes the steady-state pulse duration in terms of gain modulation strength, pump power, intracavity bandwidth, pump pulse length and cavity detuning. For a pump-pulse length of 100 ps and a bandwidth of more than 500 Å for the intracavity tuning element dye-laser pulses as short as 0.35 ps have been obtained. Under these conditions up to 100 mW of average output power were provided. In addition, mode-locking of an Oxazine 750 dye laser by synchronous pumping with the cw train of pulses obtained from the Oxazine-1-Perchlorate laser is reported.     

Compact, Low Threshold Nd^3＋：YVO4 Self-Raman Laser at 1178 nm

A compact low-threshold Raman laser at 1178 nm is experimentally realized by using a diode-end-pumped actively Q-switched Nd^3＋ ：YVO4 self-Raman laser. The threshold is 370mW at a pulse repetition frequency of S kHz. The maximum Raman laser output is 182 m W with the pulse duration smaller than 20 ns at a pulse repetition frequency of 30kHz with 1.8 W incident power. The optical efficiency from the incident power to the Raman laser is 10% and the slope efficiency is 13.5%.     

Low Timing Jitter and Tunable Dual-Wavelength Picosecond Pulse Generation from a Fabry--Pérot Laser Diode with External Injection

A novel scheme to generate tunable dual-wavelength optical pulses with low timing jitter at arbitrary repetition rates is proposed and demonstrated experimentally. The pulses are generated from a gain-switched Fabry-Pérot laser diode with two external cw beams for injection seeding simultaneously. The cw light is generated by two independent distributed feedback laser diodes, and their wavelengths can be tuned independently by two temperature controllers. The dual-wavelength pulses with the pulse width of 57 ps, the timing jitter of 340 fs, are obtained. The sidemode-suppression ratio of the output pulses is better than 23dB over a 10-nm wavelength tuning range.     

Two-wavelength self-seeded pulsed tunable laser

A compact self-seeded pulsed tunable laser is described. Its optical cavity comprises a diffraction grating, operating at a grazing angle of incidence as a spectral selector and narrow-band spectral gate. The grating couples two partially overlapping laser channels: a highly selective master laser and a nonselective slave laser. Due to the implemented efficient intracavity self-seeding the laser emits spectrally pure single-longitudinal-mode radiation at two independently tunable wavelengths, with an efficiency and output energy that are typical for nonselective lasers. Results of the experimental investigation of the laser’s output characteristics are presented. Received: 12 March 2001 / Revised version: 10 December 2001 / Published online: 7 February 2002     

Thermal effects investigation and cavity design in passively mode-locked Nd:YVO4 laser with a SESAM

A diode-pumped passively mode-locked Nd:YVO₄ laser with a five-mirror folded cavity is presented by using a semiconductor saturable absorber mirror (SESAM). The temperature distribution and thermal lensing in laser medium are numerically analyzed to design a special cavity which can keep the power density on SESAM under its damage threshold. Both the Q-switched and continuous-wave mode-locked operation are experimentally realized. The maximum average output power of 8.94 W with a 9.3 ps pulse width at a repetition rate of 111 MHz is obtained under a pump power of 24 W, correspondingly the optical slope efficiency is 39.2%.     

Tunable, μs-pulsed ytterbium fiber laser system with a linewidth below 2.7 GHz

We report on a widely tunable, pulsed laser system with narrow spectral linewidth based on a continuous wave ytterbium fiber oscillator, a pulse shaper and a power amplifier stage. The system is tunable from 1055 nm to 1085 nm and provides a maximum pulse energy of 155 μJ with a pulse duration of 1-5 μs. The linewidth is less than 2.7 GHz over the whole tuning range.     

Multiple-Pulse Operation in Passively Mode-Locked Fibre Laser with Positive Dispersion Cavity

We report the observation of rectangular shape spectrum in passively mode-locked fibre laser with positive dispersion cavity. The spectrum is broad and flat, and 3dB bandwidth can be up to 17.61 nm. Multiple-pulse operation is observed in our laser system. The spectrum width, pulse energy, pulse width and peak power of the mode-locked laser output change with the appearance of multiple-pulse operation.     

Femtosecond hybrid mode-locked semiconductor laser and amplifier dynamics

We describe the generation of femtosecond high power optical pulses using hybrid passive-active mode-locking techniques. Angle stripe geometry GaAs/AlGaAs semiconductor laser amplifiers are employed in an external cavity including prisms and a stagger-tuned quantum-well saturable absorber. An identical amplifier also serves as an optical power amplifier in a stretched pulse amplification and recompression sequence. After amplification and pulse compression this laser system produces 200 fs, 160 W peak power pulses. We discuss and extend our theory, and supporting phenomenological models, of picosecond and subpicosecond optical pulse amplification in semiconductor laser amplifiers which has been successful in calculating measured spectra and time-resolved dynamics in our amplifiers. We have refined the theory to include a phenomenological model of spectral hole-burning for finite intraband thermalization time. Our calculations are consistent with an intra-band time of approximately 60 fs. This theory of large signal subpicosecond pulse amplification will be an essential tool for understanding the mode-locking dynamics of semiconductor lasers and for analysis of high speed multiple wave-length optical signal processing and transmission devices and systems based on semiconductor laser amplifiers.     

Temporal synchronization of independently tunable single longitudinal mode hybrid CO2 lasers

We report a quantitative study of temporal synchronization of two independently tunable, single longitudinal mode, hybrid CO₂ lasers, sharing a common high pressure section. The theoretical estimates for the dependence of the laser pulse build up time on the cw section pressure are in satisfactory agreement with the experimental results. Further, we show that temporal synchronization over a larger frequency range with no significant degradation of peak power or longitudinal mode selection is possible, by utilising the cw section gain length and cavity Q as additional control parameters.     

Diode end-pumped Q-switched high-power intracavity frequency-doubled Nd:GdVO4/KTP green laser

A diode-laser-array end-pumped acousto-optically Q-switched intracavity frequency-doubled Nd:GdVO₄/KTP green laser, formed with a three-mirror folded resonator, has been demonstrated. With 15 W of pump power incident upon the Nd:GdVO₄ crystal, a maximum average green output power of 3.75 W was obtained at 50 kHz of pulse repetition frequency, giving an optical conversion efficiency of 25%, whereas the effective intracavity frequency-doubling efficiency was determined to be 72%. At the incident pump power of 12.8 W, the shortest laser pulse was achieved at a pulse repetition rate of 10 kHz, the resulting pulse width, single pulse energy, and peak power were measured to be 35 ns, 108 μJ, and 3.1 kW, respectively. Received: 18 May 2000 / Published online: 20 September 2000     

Development of a nearly transform-limited, low-repetition-rate, picosecond optical parametric generator

A low-repetition-rate (10-Hz), picosecond (ps) optical parametric generator (OPG) seeded at the idler wavelength with a high-power diode laser is demonstrated. The output of the OPG at ∼566 nm is amplified in dye cells, resulting in signal enhancement by more than three orders of magnitude. The nearly transform-limited beam at ∼566 nm has a pulsewidth of ∼170 ps, with an overall output of ∼2.3 mJ/pulse. The laser is tuned either by tuning the nonlinear crystal or the seed-laser current. The applications of such a simple, compact, high-performance, tunable ps laser system for linear and nonlinear spectroscopies are outlined.     

高重复频率、单模纳秒脉冲全光纤激光器

报道了一种基于主振荡放大技术的全光纤脉冲激光器.种子激光器使用直接调制的单纵模半导体激光器,其输出波长为1 063.8 nm,重复频率100 kHz~10 MHz连续可调谐,光纤放大器采用了多级放大器级联的方法.在重复频率100 kHz、脉冲宽度5 ns时,激光器获得了平均功率为1.2 W,峰值功率为2.4 kW的单横模激光脉冲输出.     

A 1550-nm linearly tunable CW single-mode external cavity diode laser based on a single-cavity all-dielectric thin-film Fabry–Pérot filter

A 1550-nm linearly tunable CW single-mode external cavity diode laser (ECDL) based on a single-cavity all-dielectric thin-film Fabry–Pérot filter (s-AFPF) is proposed and realized in this paper. Its internal optical components as well as their operation mechanisms are introduced first, and then its longitudinal mode output characteristic is theoretically analyzed. Afterwards, we set up the experimental platform for the output characteristic measurement of this tunable ECDL; under different experimental conditions, we execute accurate and real-time measurements for the output central wavelength, output optical power, output longitudinal mode distribution, and the line-width of the tunable ECDL in its tuning process. By summing up the optimal experimental condition from the measured data, we obtain the optimal tunable relevant parameters ECDL of the tunable ECDL has a linear mode-hop-free wavelength tuning region of 1547.203 nm-1552.426 nm, a stable output optical power in the range of 40 μW-50 μW, and a stable output longitudinal mode distribution of a single longitudinal mode with a line-width in the range of 100 MHz-150 MHz. This tunable ECDL can be used in environmental gas monitoring, atomic and molecular laser spectroscopy research, precise measurements, and so on.     

Highly Stable, Diode-Pumped Nd：YLF Regenerative Amplifier

We present the design and experimental results for a diode pumped Nd：YLF regenerative amplifier applied to amplify a nanosecond laser pulse. Numerical simulation shows that the maximum output energy and the best stability can be obtained when the regenerative amplifier operates in a saturated mode for all pulse duration and temporal profiles. Using extra post-pulse is a good method to decrease the square-pulse distortion caused by gain saturation effect. The amplifier shows output energy of 4.2mJ with a total energy gain of more than 10^7 and output energy stability of better than 1% rms. When extra post-pulse is added, square-pulse distortion is decreased from 1.33 to 1.17 for the amplifier that is seeded with an optical pulse of 3ns.     

Numerical study of active mode locking in pulsed solid-state lasers

Transient mode locking of spiking solid-state lasers is studied with the help of two theoretical approaches. The first of them is an extension of the previous transient theory with single-mode rate equations to find the limited spike build-up time depending on the modulation index. The second is based on semiclassical multimode equations describing both spiking behaviour and formation of the picosecond pulse from the initial noise. The derivation of the equations as well as a comparison of results from both approaches are given. The obtained numerical results agree with experimental data. It is shown that the pulsewidth in a spiking laser can approach the small value predicted by the steady-state theory. This minimal pulsewidth can be reached at a smaller modulation index than predicted by the standard transient mode locking theory. The minimal modulation index for generation of good picosecond pulses free of noise is found to be 0.6 in our case. Losses connected with amplitude modulation have a negligible effect on spike build-up time and pulse duration.     

高重复频率、单模纳秒脉冲全光纤激光器

报道了一种基于主振荡放大技术的全光纤脉冲激光器.种子激光器使用直接调制的单纵模半导体激光器,其输出波长为1 063.8 nm,重复频率100 kHz～10 MHz连续可调谐,光纤放大器采用了多级放大器级联的方法.在重复频率100 kHz、脉冲宽度5 ns时,激光器获得了平均功率为1.2 W,峰值功率为2.4 kW的单横模激光脉冲输出.