Voltammetric determination of mesotrione at hanging mercury drop electrode

A study of the electrochemical reduction of the mesotrione pesticide on a hanging mercury drop electrode (HMDE) was performed as a basis for the development of a sensitive analytical method for natural samples. The electrochemical characteristics of herbicide mesotrione dissolved in a phosphate buffer (pH 7.0) have been determined by means of electrochemical techniques such as cyclic voltammetry (CV) and differential pulse voltammetry (DPV) over a wide range of pH from 2.0 to 10.0. The experimental parameters, such as electrolyte type and its pH, pulse amplitude, and scan rate were optimized. The method was applied to the determination of the pesticide in a spiked soil samples. Using this method, a linear calibration curve for mesotrione was obtained up to the 0.1 μM range in pH 7 phosphate buffer solution with a detection limit (S/N = 3) of 50 nM. The method can be applied successfully to the determination of mesotrione in soils. The text was submitted by the authors in English.     

Adsorptive stripping voltammetric determination of dimenhydrinate at a hanging mercury drop electrode

Dimenhydrinate exhibits a single adsorptive stripping peak at a hanging mercury drop electrode after accumulation at 0.0V vs Ag/AgCl electrode at pH 3.8 (acetate buffer). The addition of trace amounts of copper ions enhanced the dimenhydrinate peak and its height depends on the concentration of each dimenhydrinate and Cu²⁺. The adsorptive stripping response was evaluated with respect to accumulation time and potential, concentration dependence, electrolyte, the presence of other purines, surfactants and other metal ions, and some variables. The calibration graph for dimenhydrinate determination is linear over the range 2.0×10^–8–2.0×10^–7 M (pre-concentration for 60s). The correlation factor is found to be 0.985 and RSD is 3.2% at 1.0×10^–7 M. Detection limit is 1.0×10^–8 M after 5 min accumulation. The determination of dimenhydrinate in pharmaceutical formulations by the proposed method is also reported.     

Convolutive forecasting at a hanging mercury drop electrode

Convolutive forecasting is a procedure which converts a non-steady-state voltammogram into a steady-state voltammogram. The procedure was found to be successful on a range of sphericities generated by varying the size of a hanging mercury drop and the potential sweep rate in a series of cyclic voltammetric experiments. Both theoretical and experimental analyses on a reversible electrochemical system were considered. An expression establishing the relationship between the radius of a spherical electrode and the potential sweep rate was developed to define the limits of the convolutive forecasting algorithm which was used.     

Square-wave voltametric method for determination of molinate concentration in a biological process using a hanging mercury drop electrode

A square-wave voltammetric (SWV) method using a hanging mercury drop electrode (HMDE) has been developed for determination of the herbicide molinate in a biodegradation process. The method is based on controlled adsorptive accumulation of molinate for 10 s at a potential of –0.8 V versus AgCl/Ag. An anodic peak, due to oxidation of the adsorbed pesticide, was observed in the cyclic voltammogram at ca. –0.320 V versus AgCl/Ag; a very small cathodic peak was also detected. The SWV calibration plot was established to be linear in the range 5.0×10^–6 to 9.0×10^–6 mol L^–1; this corresponded to a detection limit of 3.5×10^–8 mol L^–1. This electroanalytical method was used to monitor the decrease of molinate concentration in river waters along a biodegradation process using a bacterial mixed culture. The results achieved with this voltammetric method were compared with those obtained by use of a chromatographic method (HPLC–UV) and no significant statistical differences were observed.     

Indirect determination of lutetium by differential pulse anodic stripping voltammetry at a hanging mercury drop electrode

Lutetium has been determined by differential pulse anodic stripping voltammetry in an acidic solution containing Zn-EDTA. Lutetium (III) ions liberated zinc (II), which was preconcentrated on a hanging mercury drop electrode and stripped anodically, resulting in peak current linearly dependent on lutetium (III) concentration. Less than 0.4 ng mL⁻¹ lutetium could be detected after a 2 min deposition.      

Low-level determination of silicon in steels by anodic stripping voltammetry on a hanging mercury drop electrode

The sensitive differential pulse anodic stripping voltammetry (DPASV) proposed originally by Ishiyama et al. (2001) has been revised and improved to allow the accurate measurement of silicon on a hanging mercury drop electrode (HMDE) instead of a glassy carbon electrode. We assessed the rate of formation of the partially reduced β-silicododecamolybdate and found that metallic mercury promotes the reaction in the presence of a large concentration of Fe³⁺. The scope of the method has been broadened by carrying out the measurements in the presence of a constant amount of Fe³⁺. The limit of detection (LOD) of the method described in the present paper is 100 μg Si g⁻¹ of steel, with a relative precision ranging from 5% to 12%. It can be further enhanced to 700 ng Si g⁻¹ of steel provided the weight of the sample, the dilution factors, the duration of the electrolysis and the ballast of iron are adequately revised. The tolerance to several interfering species has been examined, especially regarding Al³⁺, Cr³⁺ and Cr VI species. The method was validated using four low-alloy ferritic steels certified by the National Institute of Standards and Technology (NIST). Its application to nickel base alloys as well as to less complicated matrixes is straightforward. It has also been successfully applied to the determination of free silicon into silicon carbide nano-powder.     

槲皮素在悬汞电极上的伏安行为研究

应用循环扫描伏安法考察槲皮素在悬汞电极上的电化学行为,并用线性扫描伏安法测定其含量。在0.1mol/LNa2CO3-NaHCO3(pH9.51)缓冲溶液中,槲皮素在-1.33V(vs.Ag/AgCl)处出现灵敏的还原峰,峰电流与其浓度在2.0×10-6～2.0×10-5mol/L(r=0.9989)范围内呈良好的线性关系。该方法可直接用于罗布麻叶中槲皮素的含量测定。     

甘草苷在悬汞电极上的电化学行为及方法研究

运用循环伏安法(CV)考察了甘草苷在悬汞电极(HMDE)上的电化学还原行为,在-0.7~-1.7 V(vs.SCE)电位窗口及0.10 mol/L(NH4)2SO4溶液中甘草苷在HMDE上的循环伏安行为是一在低扫描速度(<100 mV/s)下受吸附控制,在高扫描速度下受扩散控制的不可逆还原过程,还原峰电位(Epc)为-1.491 V。运用计时库仑法(CC)、计时电流法(CA)测定并计算了甘草苷的电荷传递系数α、扩散系数D以及表观速率常数Kf等电极过程动力学参数。初步探讨了甘草苷在HMDE上的反应机理,同时运用方波伏安法(SWV)研究了甘草苷在HMDE上的方波伏安行为,还原峰电流与其浓度在1.2×10-6~1.2×10-5mol/L及1.2×10-5~1.2×10-3mol/L范围内呈良好的线性关系,相关系数R=0.9936及0.9966,检出限8.0×10-7mol/L,据此可建立直接电化学测定甘草苷含量的方法。     

Determination of arsenic by cathodic stripping voltammetry at a hanging mercury drop electrode

Arsenic (III), respectively arsenic(V) after the reduction were determined in model solutions and some inorganic and organic materials by fast scan differential pulse cathodic stripping voltammetry and by direct current cathodic stripping voltammetry with a rapid increase of potential. The accumulation on a hanging mercury drop electrode followed by cathodic stripping was carried out in 0.7–0.8M HCl or 1–2M H₂SO₄ solutions containing Cu(II)-ions. Detection limits calculated from regression parameters was determined to be under 1 ng/ml for the samples containing very low arsenic concentrations. The relative standard deviation did not reach 8% for arsenic contents about of 5 ng/ml.     

Electroreduction of diphenyldiazomethane in acetonitrile at a hanging mercury drop electrode

Cyclic voltammetric studies of the reduction of diphenyldiazomethane (Ph₂CN₂) in CH₃CN-Me₄NPF₆ at a hanging mercury drop electrode have established that the halflife of Ph₂CN₂^? is less than l ms at either 8°C or ?37°C.     

Direct determination of traces of silver in mercury by voltammetry at the hanging mercury drop electrode in acetonitrile medium

A direct method for the determination of silver in mercury is described. The sample of mercury is introduced into the container of the hanging mercury drop electrode and the anodic voltammograms are recorded in a 0.1 M lithium perchlorate solution in acetonitrile. The anodic peak of silver obtained under these conditions is well separated from the mercury dissolution current. The peak height is proportional to silver concentration over the wide range 2 × 10^?6 mol dm^?3 (1.6 × 10^?6%) to at least 2.0 × 10^?2 mol dm^?3. No prior separation is needed; the procedure requires less than 20 min. The diffusion coefficient of silver in mercury was determined at several temperatures. It was found that silver in mercury does not form intermetallic compounds with copper, lead, thallium, cadmium, tin and bismuth.     

Developing a sequential injection-square wave voltammetry (SI-SWV) method for determination of atrazine using a hanging mercury drop electrode

This paper describes the development of a sequential injection analysis method to automate the determination of atrazine by square wave voltammetry exploiting the concept of monosegmented flow analysis to perform in-line sample conditioning and standard addition. To perform these tasks, an 800 μL monosegment is formed, composed by 400 μL of sample and 400 μL of buffer/standard solution. To obtain an efficient homogenization, the sample solution is divided in five zones intercalated by four zones of the Britton-Robinson buffer (pH 2.0) in presence of appropriate concentration of NaNO₃ and varying atrazine standard concentrations. This mixture zone is isolated from the carrier solution by two 100 μL air bubbles. After homogenization in an auxiliary reaction coil the mixture zone is injected toward the flow cell, which is adapted to the capillary of a hanging drop mercury electrode, at a flow rate of 50 μL s⁻¹. After a suitable delay time, the potential is scanned from −0.5 to −1.2 V versus Ag/AgCl using a frequency of 300 Hz and pulse height of 25 mV. The linear dynamic range is observed for atrazine concentrations between 1.16 × 10⁻⁷ and 2.32 × 10⁻⁶ mol L⁻¹, obeying the linear equation i_p = (−6.91 ± 0.07) × 10⁸[atrazine] + (4 ± 8), with r² = 0.9996, for which the slope is given in nA L mol⁻¹. The detection and quantification limits of the method are 2.1 × 10⁻⁸ and 7.0 × 10⁻⁸ mol L⁻¹, respectively. The sampling frequency is 37 h⁻¹, when the standard addition protocol is followed. This frequency can be increased to 42 h⁻¹ if the protocol to obtain in-line calibration curve is used for quantification. The method was applied for determination of atrazine in spiked river water samples and its accuracy was evaluated by comparison with the batch standard addition approach, which revealed that there is no evidence of statistically significant differences between the two methods.     

Electrochemical behaviour of sertraline at a hanging mercury drop electrode and its determination in pharmaceutical products

The electrochemical behaviour of sertraline at a hanging mercury drop electrode (HMDE) was described. Different voltammetric techniques, such as cyclic, linear sweep, differential pulse and square wave voltammetry, were used. Voltammograms were obtained at different pH values with a Britton-Robinson buffer solution used as supporting electrolyte. The best results were found by square wave voltammetry with electrodeposition at alkaline pH using a borate buffer with a pH = 8.2 for the samples, containing 12% (v/v) methanol. Under optimised conditions, a linear relationship between 2.33 x 10(-7) and 3.15 x 10(-6) M of sertraline with a limit of detection of 1.98 x 10(-7) M was obtained. The electrochemical method developed was applied to the determination of sertraline in pharmaceutical formulations. Recoveries were close to 100%, thus proving efficacy of the proposed method for the quantification of sertraline in commercial samples.     

Electrochemical behaviour of sertraline at a hanging mercury drop electrode and its determination in pharmaceutical products

The electrochemical behaviour of sertraline at a hanging mercury drop electrode (HMDE) was described. Different voltammetric techniques, such as cyclic, linear sweep, differential pulse and square wave voltammetry, were used. Voltammograms were obtained at different pH values with a Britton-Robinson buffer solution used as supporting electrolyte. The best results were found by square wave voltammetry with electrodeposition at alkaline pH using a borate buffer with a pH = 8.2 for the samples, containing 12% (v/v) methanol. Under optimised conditions, a linear relationship between 2.33 × 10^–7 and 3.15 × 10^–6 M of sertraline with a limit of detection of 1.98 × 10^–7 M was obtained. The electrochemical method developed was applied to the determination of sertraline in pharmaceutical formulations. Recoveries were close to 100%, thus proving efficacy of the proposed method for the quantification of sertraline in commercial samples. Received: 26 September 2000 / Revised: 1 December 2000 / Accepted: 5 December 2000     

Catalytic currents of albumin at the hanging mercury drop electrode

Bovine serum albumin (BSA), as well as completely reduced BSA denoted by P (SH)₃₅, are adsorbed on the hanging mercury drop electrode (HMDE) from alkaline buffer solutions. When time is allowed, a monolayer is adsorbed from very dilute (10^?9M) BSA solutions in ammoniacal and borate buffers. With a monolayer of adsorbed protein the voltammograms at the HMDE are then identical in a given ammoniacal or borax buffer containing cobalt(III) or (II) and different BSA concentrations. Voltammograms of P (SH)₃₅ are virtually identical with those of native BSA. At the HMDE the second Brdi?ka current is proportional to concentration of cobalt(III) or (II) and the first current nearly so. Incompletely or completely adsorbed BSA or P (SH)₃₅ is not desorbed on keeping the HMDE for one hour in ammonia buffers. An incomplete layer of adsorbed BSA or P (SH)₃₅ is relatively rapidly desorbed at ?1.6 V (vs. SCE) and a complete film at ?1.65 V, some desorption occurring at ?1.6 V. Upon desorption, the second Brdi?ka current decreases faster than the first one; this is particularly striking in 1 M ammonia buffer. The rate of desorption is increased by calcium chloride, but the rate of adsorption is not, or only slightly, increased in the presence of calcium. Incomplete adsorption occurs at ?1.60 V (vs. SCE) and no adsorption at ?1.65 V. Indications are obtained that “presodium currents” yield a slight plateau at ?1.67 to ?1.70 V, the plateau currents being attributed to adsorbed BSA, while unadsorbed BSA yields catalytic currents without a plateau, the currents merging with the residual one of the buffer. Calcium chloride greatly increases the presodium currents. From many kinetic data obtained at the dropping mercury electrode (DME) and from results at the HMDE it is concluded that, depending on the BSA concentration, Brdi?ka currents at the DME are partly of a kinetic and partly of a surface adsorption nature and partly diffusion-controlled. Adsorption equilibrium is not attained at the DME at 25° at concentrations of BSA smaller than 10^?6M.     

Electrochemical behaviour of tilmicosin at the hanging mercury drop electrode

The electrochemical behaviour of tilmicosin (TIM) was investigated using cyclic voltammetry and square-wave voltammetry in Britton-Robinson buffers (pH 2–12). The voltammograms of TIM showed one-irreversible peak which attributed to reduction of the >C=C< group in the entire pH values. However, an additional peak was shown over the pH range 2.00 to 4.00. Its peak potential is more positive potential from that of >C=C< group, and its potential was not practically dependent on the pH. On the other hand, the peak potential of >C=C< group was shifted to the more negative values with increasing pH. According to the obtained voltammetric data, the probable reaction mechanism for the reduction of TIM was proposed. Moreover, the adsorption of TIM on the mercury electrode surface by means of square-wave adsorptive stripping voltammetry measurements is studied at different pH values. The peak current variations with the deposition time and TIM concentration were observed.     

Study of the voltammetric behaviour of maleic hydrazide and its determination at a hanging mercury drop electrode

Voltammetric behaviour of maleic hydrazide pesticide dissolved in a Britton-Robertson buffer was investigated by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). It was found that the process at the Hg electrode was diffusion controlled; the reaction was irreversible and involved a change of one proton and a transfer of one electron. A quantitative differential pulse voltammetric method for determination of maleic hydrazide was developed on the basis of these studies involving the reduction of the compound at a hanging mercury drop electrode. A linear calibration was obtained in the range of 0.5-5.5 mg l⁻¹, and the developed DPV methodology was then applied for the determination of maleic hydrazide in spiked vegetable samples by the standard addition method. Satisfactory percentage R.S.D. (∼2%), percentage recovery values (∼85%) and LOD (0.215 mg l⁻¹) were obtained. These compared well with the results from the alternative spectrophotometric method.     

Parameter evaluation for the determination of selenium by cathodic stripping voltammetry at the hanging mercury drop electrode

The behaviour of selenium(IV) in cathodic stripping voltammetry is evaluated systematically. The effects of copper concentration, pH, deposition potential and complexing agents on the stripping peak are examined and criteria are given for the choice of suitable quantitative parameters. The detection limit was found to be 20 ng l^?1 and the background contamination level was 35 ng l^?1. Zinc and lead do not affect the determination of selenium if EDTA is added to the solution whereas cadmium interferes badly; the corresponding mechanisms are discussed.     

Creatinine sensor based on a molecularly imprinted polymer-modified hanging mercury drop electrode

Molecularly imprinted polymers (MIP) have been elucidated to work as artificial receptors. In our present study, a MIP was applied as a molecular recognition element to a chemical sensor. We have constructed a creatinine sensor based on a MIP layer selective for creatinine and its differential pulse, cathodic stripping voltammetric detection (DPCSV) on a hanging mercury drop electrode (HMDE). The creatinine sensor was fabricated by the drop coating of dimethylformamide (DMF) solution of a creatinine-imprinted polymer onto the surface of HMDE. The modified-HMDE, preanodised in neutral medium at +0.4 V versus Ag/AgCl for 120 s, exhibited a marked enhancement in DPCSV current in comparison to the less anodised (≤+0.3 V) HMDE. The creatinine was preconcentrated and instantaneously oxidised in MIP layer giving DPCSV response in the concentration range of 0.0025-84.0 μg mL⁻¹ [detection limit (3σ) 1.49 ng mL⁻¹]. The sensor was found to be highly selective for creatinine without any response of interferents viz., NaCl, urea, creatine, glucose, phenylalanine, tyrosine, histidine and cytosine. The non-imprinted polymer-modified electrode did not show linear response to creatinine. The imprinting factor as high as 9.4 implies that the imprinted polymer exclusively acts as a recognition element of creatinine sensor. The proposed procedure can be used to determine creatinine in human blood serum without any preliminary treatment of the sample in an accurate, rapid and simple way.