Label-free detection of rheumatoid factor using YbYxOy electrolyte–insulator–semiconductor devices

In this study, we investigated the effect of yttrium content on the structural properties and sensing characteristics of YbY_xO_y sensing membranes for electrolyte–insulator–semiconductor (EIS) sensors to detect the rheumatoid factor (RF). The YbY_xO_y EIS device prepared at the 60 W plasma condition exhibited a higher sensitivity of 65.77 mV/pH, a lower hysteresis voltage of ∼1 mV, and a smaller drift rate of 0.14 mV/h than did those prepared at the other conditions. We attribute this behavior to the optimal yttrium content in the YbY_xO_y film forming a smooth surface. Furthermore, we used a novel YbTi_xO_y EIS biosensor to measure the RF antigen in human serum because of its rapid and label-free detection. Two different techniques were used for the immobilization of RF antibody onto the surface of an YbTi_xO_y EIS sensor. The RF antibody was directly immobilized on the EIS surface modified with 3-aminopropyltriethoxysilane (APTES) followed by glutaraldehyde (GA). In contrast, a mixture of 1-ethyl-3-(3-dimethylamino-propyl)carbodiimide (EDC) and N-hydroxysuccinimide (NHS) solution was used to functionalize the carboxyl groups at the tail of RF antibodies. RF antibodies functionalized with the active NHS esters were covalently immobilized on the APTES-modified YbTi_xO_y surface. The immobilized RF antibodies on the EIS that are functionalized with the EDC and NHS exhibit higher (41.11 mV/pC_RF) for detection of serum RF antigen in the range 10⁻⁷ to 10⁻³ M, compared to traditional antibody immobilization technique via APTES and GA linkage. The YbTi_xO_y EIS biosensor is a promising analytical tool for RF antigen monitoring due to its good sensitivity, stability and repeatability.     

High dielectric constant PrYxOy sensing films electrolyte-insulator-semiconductor pH-sensor for the detection of urea

In this paper, we describe the structural and sensing properties of high-k PrY_xO_y sensing films deposited on Si substrates through reactive co-sputtering. Secondary ion mass spectrometry and atomic force microscopy were employed to analyze the compositional and morphological features of these films after annealing at various temperatures. The electrolyte-insulator-semiconductor (EIS) device incorporating a PrY_xO_y sensing membrane that had been annealed at 800 °C exhibited good sensing characteristics, including a high sensitivity (59.07 mV pH⁻¹ in solutions from pH 2 to 12), a low hysteresis voltage (2.4 mV in the pH loop 7 → 4 → 7 → 10 → 7), and a small drift rate (0.62 mV h⁻¹ in the buffer solution at pH 7). The PrY_xO_y EIS device also showed a high selective response towards H⁺. This improvement can be attributed to the small number of crystal defects and the large surface roughness. In addition, the enzymatic EIS-based urea biosensor incorporating a high-k PrY_xO_y sensing film annealed at 800 °C allowed the potentiometric analysis of urea, at concentrations ranging from 1 to 16 mM, with a sensitivity of 9.59 mV mM⁻¹.     

Cooperative effect of Fe and Ti species over Fe–Ti–Ox catalysts on the catalytic hydrolysis performance of hydrogen cyanide

FeO_x, TiO₂, and Fe–Ti–O_x catalysts were synthesized and used in the catalytic hydrolysis of hydrogen cyanide (HCN). Nearly 100% HCN conversion was achieved at 250 °C over the Fe–Ti–O_x catalyst. TiO₂ rutile was detected over TiO₂, but not over Fe–Ti–O_x, which suggested that the interaction between Fe and Ti species could inhibit the TiO₂ phase transition. Furthermore, the interaction between Fe and Ti species over Fe–Ti–O_x could promote the selectivity of NH₃ and CO. The mechanism of hydrolysis of HCN over FeO_x, TiO₂, and Fe–Ti–O_x can be given as follows: HCN + H₂O → methanamide → ammonium formate → formic acid → H₂O + CO.     

Titanium(IV) polynuclear hydroxo complexes stabilized in solution by [PW11O39]7? heteropolyanion

[PW₁₁O₃₉]^7– heteropolyanion (HPA) stabilizes Ti(IV) in aqueous solution at Ti:PW₁₁ ratios from 1 to 12 and pH 1–3. Ti(IV) is completely precipitated under these conditions in the absence of HPA. Differential dissolution phase analysis, optical, IR,³¹P and¹⁷O NMR spectra show that one Ti(IV) ion is incorporated into the Keggin lattice. The other ions, most probably, are located on the HPA surface in the form of oligomeric hydroxo fragments: [PW₁₁Ti^IVO₄₀·Ti_n–1 ^IVO_xH_y]^k–. Both types of Ti(IV) ions bind peroxo groups on interaction of the complex with H₂O₂.     

Analysis on the local structures for 3d1 impurities (Ti3+ and V4+) in KTiPO4

Making use of the perturbation formulae for 3d¹ ions (Ti³⁺ and V⁴⁺) under orthorhombically compressed octahedra, the spin Hamiltonian parameters (g factors: g_x, g_y, g_z and hyperfine structure constants: A_x, A_y, A_z) and local structures of the 3d¹ impurity centres C₁, C₂, and C₃ in KTiOPO₄ crystals are theoretically analyzed in a consistent way. The remarkable local distortions (i.e., the relative axial compression ratios 11.2%, 7.0%, and 5.5% along Z axis and the relative planar bond length variation ratios 15.9%, 7.0%, and 6.0%) are obtained for the [Ti2O₆]⁹⁻ cluster on Ti2 site and [VO₆]⁸⁻ clusters on Ti1 and Ti2 sites, respectively, in view of the Jahn–Teller effect. The above local orthorhombic distortion parameters in the impurity centres are found to be more significant than the host Ti1 and Ti2 sites in pure KTiOPO₄. The sequences (C₁ > C₂ > C₃) of the local orthorhombic distortion parameters ρ and τ are in accordance with those of the axial and perpendicular anisotropies Δg and δg of g factors, respectively.     

Control of Co content and SOFC cathode performance in Y1−ySr2+yCu3−xCoxO7+δ

The electrochemical performance of the layered perovskite YSr₂Cu_3−xCo_xO_7+δ, a potential solid oxide fuel cell (SOFC) cathode, is improved by increasing the Co content from x = 1.00 to a maximum of x = 1.30. Single phase samples with x > 1.00 are obtained by tuning the Y/Sr ratio, yielding the composition Y_1−ySr_2+yCu_3−xCo_xO_7+δ (where y ≤ 0.05). The high temperature structure of Y_0.95Sr_2.05Cu_1.7Co_1.3O_7+δ at 740 °C is characterised by powder neutron diffraction and the potential of this Co-enriched material as a SOFC cathode is investigated by combining AC impedance spectroscopy, four-probe DC conductivity and powder XRD measurements to determine its electrochemical properties along with its thermal stability and compatibility with a range of commercially available electrolytes. The material is shown to be compatible with doped ceria electrolytes at 900 °C.     

Phase composition and phase transformation in Bi(Sb,Nb,Ta)O4 system

In this work Bi(Sb_xNb_yTa_z)O₄ (x + y + z = 1) samples are prepared using mixed-oxide method. A pseudo-ternary phase diagram of Bi(Sb,Nb,Ta)O₄ system is given below the melting point. It is composed of a monoclinic phase region, an orthorhombic phase region and a monoclinic–orthorhombic co-existing phase region. In the orthorhombic phase region, the transformation from orthorhombic to triclinic phase is found to be sensitive to the composition and sintering temperature. Both the transformation from monoclinic to orthorhombic structure and the transformation from orthorhombic to triclinic structure have been studied by the cell parameters.     

Chemical stability of Ba(Ce<Subscript>1−x</Subscript>Ti<Subscript>x</Subscript>)<Subscript>1−y</Subscript>Y<Subscript>y</Subscript>O<Subscript>3</Subscript> proton-conducting solid electrolytes

The purpose of this work was to investigate the influence of titanium and yttrium dopants on chemical stability of selected Ba(Ce_1−xTi_x)_1−yY_yO₃ compounds. The presented results are the part of wider research concerning the crystallographic structure, microstructure, electrical and transport properties of these groups of materials. Samples of Ba(Ce_1−xTi_x)_1−yY_yO₃ with x=0.05, 0.07, 0.10, 0.15, 0.20, 0.30 and y=0.05, 0.10, 0.20 (for x=0.05) were prepared by solid-state reaction method. Initially, differential thermal analysis (DTA) and thermogravimetry (TG) were used for optimization of preparation conditions. Subsequently, DTA-TG-MS (mass spectrometry) techniques were applied for evaluation of the stability of prepared materials in the presence of CO₂. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) results were used to determine the phase composition, structure and microstructure of materials and to assist the interpretation of DTA-TG-MS results. The strong influence of Ti and Y dopants contents (x and y) on the properties was found. The introduction of Ti dopant led to the improvement of chemical stability against CO₂. The lower Ti concentration the better resistance against CO₂ corrosion was observed. Doping by Y had the opposite effect; the decrease of chemical stability was determined. In this case the higher Y dopant concentration the better resistance was observed. The attempt to correlate the influence of dopant on structure and chemical stability was also presented.     

Synthesis and spectral properties of titanium(iv) polynuclear hydroxo complexes stabilized in solution by the [PW11O39]7− heteropolyanion

Unsaturated heteropolyanions (HPA) [PW₁₁O₃₉]⁷⁻ stabilize Ti^IV hydroxo complexes in aqueous solutions (Ti: PW₁₁ [PW₁₁O₃₉]⁷⁻⪯12, pH 1–3). Spectral studies (optical,¹⁷O and³¹P NMR, and IR spectra) and studies by the differential dissolution method demonstrated that Ti^IV hydroxo complexes are stabilized through interactions of polynuclear Ti^IV hydroxo cations with heteropolyanions [PW₁₁TiO₄₀ ⁵⁻ formed. Depending on the reaction conditions, hydroxo cations Ti _n−1O _x H _y ^m+ either add to oxygen atoms of the W−O−Ti bridges of the heteropolyanions to form the complex [PW₁₁TiO₄₀·Ti _n−1O _x H _y ] ^k− (at [HPA]=0.01 mol L⁻¹) or interact with Ti^IV of the heteropolyanions through the terminal o atom to give the polynuclear complexes [PW₁₁O₃₉Ti−O−Ti _n−1O _x H _y ]^q− (at [HPA]=0.2 mol L⁻¹). When the complexes of the first type were treated with H₂O₂, Ti^IV ions added peroxo groups. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 914–920, May, 1997.     

Nickel (II) tetrapyridyl complexes as electrocatalysts and precatalysts for water oxidation

Two nickel complexes, [Ni(tpen)](ClO₄)₂.0.5CH₃COCH₃ ( 1 ) and [Ni(tpbn)](ClO₄)₂ ( 2 ), of tetrapyridyl ligands N,N,N′,N′-tetrakis(2-pyridyl-methyl)-1,2-ethanediamine (tpen) and N,N,N′,N′-tetrakis(2-pyridyl-methyl)-1,4-butanediamine (tpbn) were prepared and their catalysis for water oxidation reaction (WOR) studied. In 0.1 M phosphate buffer solution (PBS) of pH 8.0, complex 1 is a homogeneous molecular catalyst with an overpotential of ~440 mV and a Faradaic efficiency of 89%. At pH ≥ 9.0, complex 1 degraded gradually during the catalytic process and formed NiO_x composite (nickel oxide with general formula Ni_xO_yH_z) active for WOR. In contrast, complex 2 deteriorated under measured conditions (pH 8.0–12.0) and formed NiO_x composite active for WOR. The NiO_x composite derived from 1 in 0.1 M PBS at pH 11.0 showed an activity with an overpotential of ~500 mV, a Tafel slope of ~90 mV/decade and a Faradaic efficiency of 97%. Mechanisms were proposed for water oxidation catalyzed by 1 and 2 . This work revealed that the catalytic activity of the nickel complexes was related to the flexibility of the tetrapyridyl ligands and the adaptability of the coordination sphere of the nickel(II) center.     

Application of mechanochemical activation for synthesis of uranium–lanthanoid mixed oxides

The applicability of mechanochemistry to produce uranium–lanthanoid mixed oxides is presented. Phase homogeneous uranium–cerium solid solutions of the type Ce _x U_1−x O₂ (x = 0.3 ÷ 0.95) and polyphase systems containing La _y U_1−y O_2+x (y = 0.12) were prepared by mechanochemical activation in air of sol–gel produced precursors. The possibility for synthesis of urania–lanthania solid solution by mechanochemical interaction of La₂O₃ with sol–gel produced U (IV,VI) oxide is established. The crystal structures of the obtained oxides before and after the mechanochemical treatment are analysed by the use of X-ray diffraction method. The size of the crystallites (8–16 nm), lattice parameters, crystallite strains and densities of the oxides are calculated by BRASS program for Rietveld calculation.     

TNT determination based on its degradation by immobilized HRP with electrochemical sensor

Based on the mechanism of 2,4,6-Trinitrotoluene (TNT) degradation, an amperometric hydrogen peroxide biosensor was constructed for the determination of trace amounts of TNT by immobilization of MWCNTs, HRP and Nafion onto the surface of glassy carbon electrode (GCE). The Nafion/MWCNTs/HRP biosensor was capable of degrading TNT with the consumption of H₂O₂ and HRP in 0.2 mol/L PBS (pH 7.0). Trace TNT was quantitative analyzed by the current decrease of H₂O₂ at the reductive potential of −0.35 V using cyclic voltammetry (CV). Effect of the ratio of MWCNTs/HRP, initial concentration of H₂O₂ and electrolyte’s pH were also optimized by CV. Under the optimal conditions, the current decrease of H₂O₂ that was consumed by TNT degradation was proportional to TNT ranging from 8.8 × 10⁻⁹ mol/L to 2.64 × 10⁻⁷ mol/L with a detection limit of 3.0 × 10⁻⁹ mol/L (S/N = 3). It developed a new way for simple, rapid and sensitive measurement of trace TNT.     

Immobilization of Hemoglobin on the Gold Colloid Modified Pretreated Glassy Carbon Electrode for Preparing a Novel Hydrogen Peroxide Biosensor

A novel hydrogen peroxide (H₂O₂) biosensor was developed by immobilizing hemoglobin on the gold colloid modified electrochemical pretreated glassy carbon electrode (PGCE) via the bridging of an ethylenediamine monolayer. This biosensor was characterized by UV-vis reflection spectroscopy (UV-vis), electrochemical impendence spectroscopy (EIS) and cyclic voltammetry (CV). The immobilized Hb exhibited excellent electrocatalytic activity for hydrogen peroxide. The Michaelis–Menten constant (K _m) was 3.6 mM. The currents were proportional to the H₂O₂ concentration from 2.6 × 10⁻⁷ to 7.0 × 10⁻³ M, and the detection limit was as low as 1.0 × 10⁻⁷ M (S/N = 3).     

Synthesis and characterization of A-site deficient rare-earth doped BaZrxTi1−xO3 perovskite-type compounds

A-site deficient rare-earth doped BaZr_xTi_1?xO₃ (BZT) ceramics were prepared from a soft-chemistry route and by solid-state reaction (SSR). Perovskite-like single-phase diagrams for the BaTiO₃–La_2/3TiO₃–BaZrO₃ system were constructed for each method of synthesis. Infrared spectroscopy on (Ba_1?yLa_2y/3)Zr_xTi_1?xO₃ solid solution revealed a dramatic stress on the M–O (M = Ti, Zr) bonds due to the combined effect of A-site vacancies and the lower ionic radius of La³⁺ than that of Ba²⁺. A relationship between the M–O stretching vibration (υ) and the tolerance factor (t) was determined. (Ba_1?yLn_2y/3)Zr_0.09Ti_0.91O₃ (Ln = La, Pr, Nd) samples synthesized by SSR were selected for detailed studies. X-ray diffraction data were refined by the Rietveld method. Scanning electron microscopy on sintered compacts detected abnormal crystal growth and grain sizes in the range of about 1 μm up to 10 μm when the dopant concentration is 6.7 at. %. Impedance measurements exhibited that ferroelectric to paraelectric phase-transition temperature shifted to lower values as increasing rare-earth content. (Ba_1?yLn_2y/3)Zr_0.09Ti_0.91O₃ system showed a diffuse phase transition with a relaxor-like ferroelectric behaviour. Furthermore, the dielectric constant was enhanced with respect to non-doped BZT system.     

NO Reduction Over Noble Metal Ionic Catalysts

In last 40 years, catalysis for NO _x removal from exhaust gas has received much attention to achieve pollution free environment. CeO₂ has been found to play a major role in the area of exhaust catalysis due to its unique redox properties. In last several years, we have been exploring an entirely new approach of dispersing noble metal ions in CeO₂ and TiO₂ for redox catalysis. We have extensively studied Ce_1−x M _x O_2−δ (M = Pd, Pt, Rh), Ce_1−x−y A _x M _y O_2−δ (A = Ti, Zr, Sn, Fe; M = Pd, Pt) and Ti_1−x M _x O_2−δ (M = Pd, Pt, Rh, Ru) catalysts for exhaust catalysis especially NO reduction and CO oxidation, structure–property relation and mechanism of catalytic reactions. In these catalysts, lower valent noble metal ion substitution in CeO₂ and TiO₂ creates noble metal ionic sites and oxide ion vacancy. NO gets molecularly adsorbed on noble metal ion site and dissociatively adsorbed on oxide ion vacancy site. Dissociative chemisorption of NO on oxide ion vacancy leads to preferential conversion of NO to N₂ instead of N₂O over these catalysts. It has been demonstrated that these new generation noble metal ionic catalysts (NMIC) are much more catalytically active than conventional nano crystalline noble metal catalysts especially for NO reduction.     

Li intercalation and anion/cation substitution of transition metal chalcogenides: Effects on crystal structure,microstructure, magnetic properties and Li+ ion mobility

We investigated experimentally the effect of Li intercalation on the structural, microstructural and magnetic properties as well as on the Li ion diffusivity of the complex chalcogenides Cr_5?yTi_ySe₈. In addition, the effect of anion substitution in TiS_2?zSe_z on the Li diffusion parameters was studied by ⁷Li nuclear magnetic resonance (NMR) spin-lattice relaxation measurements.For Cr_5?yTi_ySe₈ the Li⁺ insertion is accompanied by an irreversible phase transition from monoclinic to trigonal symmetry which is electronically driven. The maximal Li content in the host material depends on the Ti content and decreases with increasing y in Cr_5?yTi_ySe₈. The intercalated materials can be deintercalated and the minimal Li content in the residual compound increases with Ti abundance. The intercalation process is accompanied by drastic changes of the microstructure. Electrochemical discharge curves depend significantly on the Ti. According to the results of XANES investigations performed on Cr₄TiSe₈, Ti is first reduced during Li uptake and Cr atoms accept electrons at later stages of the intercalation reaction. In-situ energy dispersive X-ray diffraction experiments show that the Li intercalation at room temperature proceeds via two different mechanisms while intercalation at 60 °C is faster and is dominated by one mechanism. ⁷Li MAS NMR measurements revealed a variety of transition metal environments around the Li sites corresponding to the Cr/Ti disorder. The NMR studies also indicate fast Li dynamics. The magnetism of the educts is dominated by strong antiferromagnetic exchange interactions in the high temperature region and by spin-glass behavior in the low temperature range. Intercalation of Li weakens the antiferromagnetic exchange and for fully intercalated materials ferromagnetic exchange is observed. The interpretation of the experimental results is supported by accompanying band structure calculations.In layer-structured Li_xTiS_2?zSe_z (x ≈ 0.7) the Li diffusivity was investigated by various NMR techniques and compared with results obtained for the pure end members Li_xTiS₂ and Li_xTiSe₂. In particular, anion substitution clearly influences the slopes of the low-T flanks of the diffusion induced NMR relaxation-rate peaks. The corresponding activation barriers characterizing local hopping processes are reduced in the mixed samples with 0 < z < 2 and can be explained by a domain model. DFT calculations yield very small hopping barriers along S-rich and Se-rich domain boundaries while the barriers for Li migration inside the domains are rather high. It is therefore assumed that Li migrates along the domain boundaries.     

Regions of stability of variable-composition perovskite phases La1?xSrxMn1?yMyO3 (M = Ti, Ni)

The formation of the orthorhombic solid solution series LaMn_1−y Ti _y O₃ with 0.0 ≤ y ≤ 0.15 and LaMn_1−y Ni _y O₃ with 0.0 ≤ y ≤ 0.4 was observed. The stability boundaries of the La_1−x Sr _x Mn_1−y M _y O₃ (M = Ti, Ni) perovskite phases were determined. Fragments of isobaric-isothermal sections of the phase diagrams of the La₂O₃-SrO-Mn₃O₄-TiO₂ and La₂O₃-SrO-Mn₃O₄-NiO systems in air at 1100°C were suggested. Original Russian Text ? E.A. Filonova, A.N. Demina, A.N. Petrov, 2007, published in Zhurnal Fizicheskoi Khimii, 2007, Vol. 81, No. 10, pp. 1787–1790.     

Electrocatalytic activity and stability of Ti/IrO2 + MnO2 anode in 0.5 M NaCl solution

Ti/IrO₂(x) + MnO₂(1-x) anodes have been fabricated by thermal decomposition of a mixed H₂IrCl₆ and Mn(NO₃)₂ hydrosolvent. Cyclic voltammetry (CV) and polarization curve have been utilized to investigate the electrochemical behavior and electrocatalytic activity of Ti/IrO₂(x) + MnO₂(1-x) anodes in 0.5 M NaCl solution (pH = 2). Ti/IrO₂+MnO₂ anode with 70 mol% IrO₂ content has the maximum value of q*, indicating that Ti/IrO₂(0.7) + MnO₂(0.3) anode has the most excellent electrocatalytic activity for the synchronal evolution of Cl₂ and O₂ in dilute NaCl solution. Tafel lines displayed two distinct linear regions with one of the slope close to 62 mV dec⁻¹ in the low potential region and the other close to 295 mV dec⁻¹ in the high potential region. Electrochemical impedance spectroscopic is employed to investigate the impedance behavior of Ti/IrO₂(x) + MnO₂(1-x) anodes in 0.5 M NaCl solution. It is observed that as the R _ct, R _s and R _f values for Ti/IrO₂(0.7) + MnO₂(0.3) anode become smaller, electrocatalytic activity of Ti/IrO₂(0.7) + MnO₂(0.3) anode becomes better than that of other Ti/IrO₂ + MnO₂ anodes with different compositions. Ti/IrO₂(0.7) + MnO₂(0.3) anode fabricated at 400 °C has been observed to possess the highest service life of 225 h, whereas the accelerated life test is carried out under the anodic current of 2 A cm⁻² at the temperature of 50 °C in 0.5 M NaCl solution (pH = 2).     

A natural manganese ore as a heterogeneous catalyst to effectively activate peroxymonosulfate to oxidize organic pollutants

Heterogeneous transition metal catalysts are indispensable in improving environmental pollution. However, their fabrication is often costly and cumbersome, and they can easily pollute the environment. This study proposed using a natural Gabonese ore (GBO) containing Mn_xO_y and Fe_xO_y as catalysts to degrade orange II (OII) via peroxymonosulfate (PMS) activation. The GBO + PMS system exhibited extraordinarily high stability and catalytic activity towards OII elimination (92.2%, 0.0453 min^?1). The reactive oxygen species (ROS) generated in the system were identified using radical scavenging tests and electron spin-resonance (ESR) analysis. Singlet oxygen (¹O₂) represented the dominant reactive species for OII degradation, while the system presented a lower reaction energy barrier and was effective in a broad pH range (2–10). This work also proposed the activation mechanism for the GBO + PMS system and OII degradation pathways. This study revealed a new approach for exploring inexpensive, eco-friendly, efficient, and stable heterogeneous transition metal catalysts.     

Structural Study of Li1+x−yNb1−x−3yTix+4yO3 Solid Solutions

The structures of Li_1+x−yNb_1−x−3yTi_x+4yO₃ solid solutions within the so-called M-phase field in the Li₂O-Nb₂O₅-TiO₂ system were investigated using high-resolution transmission electron, microscope (HRTEM) and single-crystal X-ray diffraction. The results demonstrated that the phase field is not a solid solution but rather a homologous series of commensurate intergrowth structures with LiNbO₃-type (LN) slabs separated by single [Ti₂O₃]²⁺ corundum-type layers. The thickness of the LN slab decreases with increasing Ti-content from ∼55 to 3 atomic layers in the metastable H-Li₂Ti₃O₇ end-member. The LN slabs accommodate a wide range of Ti⁴⁺/Nb⁵⁺ substitution, and for a given homolog the distribution of Ti and Nb is not uniform across the slab. A single-crystal X-ray diffraction study of a structure composed of nine-layer LN slabs revealed preferential segregation of Ti to the slab surfaces which apparently provides partial compensation for the charge on the adjacent [Ti₂O₃]²⁺ corundum layers. The extra cations in phases with x>0 are accommodated through the formation of Li-rich Li₂MO₃-type layers in the middle of the LN slabs. The fraction of layers with extra cations increases with increasing Ti-content in the structure.