Li5Zn8Ga5Ge9O36: Cr3+, Ti4+: A Long Persistent Phosphor Excited in a Wide Spectral Region from UV to Red Light for Reproducible Imaging through Biological Tissue

Near‐infrared (NIR) long‐persistent phosphors (LPPs) have emerged as a potential solution for bio‐imaging applications over the past few years. However, there are enormous challenges regarding their in situ application based on their dependence on short‐wavelength excitation. In this paper, we report a multi‐spectral excited NIR LPP, Li₅Zn₈Ga₅Ge₉O₃₆: 1.5 % Cr³⁺, 0.5 % Ti⁴⁺, which overcomes the limitations of functional processes in biological tissues and other complex systems. This LPP exhibits a high luminescent intensity and a long emission duration in the NIR region (700–800 nm). The applicability of this phosphor to tissue imaging is demonstrated experimentally. Its persistent luminescence (PersL) can easily penetrate approximately 2 mm of pork flesh. More importantly, this phosphor can be re‐charged in situ using a red LED or laser diode array to provide renewed NIR PersL for biological tissues, which is beneficial for long‐term biological tissue imaging applications with high signal‐to‐noise ratios. Systematic investigations of the nature of energy traps and PersL mechanisms are also reported in this paper.     

Controlling Cr3+/Cr4+ concentration in single-phase host toward tailored super-broad near-infrared luminescence for multifunctional applications

Full control on the valence of the active ions in solids to improve properties is the central topic of chemistry and materials. Cr³⁺ and Cr⁴⁺ ions generally emit wavelength-different near-infrared (NIR) light. Here, we have developed a chromium valence-controllable single-phase phosphor, Mg₂GeO₄:Cr³⁺,Cr⁴⁺ to achieve super-broad NIR luminescence. High Li ⁺ content charge compensators can stabilize Cr³⁺, whereas high-temperature sintering tends to facilitate the formation of Cr⁴⁺. Through fine adjusting the synthesis conditions, pure Cr³⁺ or Cr⁴⁺ luminescence can be obtained with peak emission locating at 935 nm and 1190 nm, respectively. Super broad band dual emission spanning from 650 nm to 1600 nm is realized via fully controlling the concentration ratio of Cr³⁺ to Cr⁴⁺ in a single host. By measuring the transmission spectra of several foodstuff illuminated by our phosphors, non-destructive analysis in food safety areas can be realized. This study provides a new strategy for exploiting super broad band NIR luminescent materials.     

A near-infrared phosphor doped with Cr3+ towards zero-thermal-quenching for high-power LEDs

Cr³⁺-doped phosphors show significant application potential in near-infrared (NIR) light-emitting diodes (LEDs). However, the development of thermally stable and efficient NIR phosphors still faces enormous challenges. Herein, NIR phosphors K₂NaMF₆:Cr³⁺ (M³⁺ = Al³⁺, Ga³⁺, and In³⁺) were synthesized by the hydrothermal method. The represented K₂NaAlF₆:Cr³⁺ phosphor can be effectively excited by blue light (～430 nm) to present broadband emission at half a maximum of 96 nm peaking at ～ 728 nm. Meanwhile, the K₂NaAlF₆:Cr³⁺ phosphor exhibits excellent internal quantum efficiency (IQE = 68.08%) and nearly zero-thermal-quenching behavior, which is able to maintain 96.5% emission intensity at 150 °C of the initial value at 25 °C. The NIR phosphor-converted LED was fabricated based on K₂NaAlF₆:Cr³⁺ phosphor and a blue LED chip, showing a NIR output power of 394.39 mW at 300 mA with a high photoelectric conversion efficiency of 10.9% at 20 mA. Using the high-power NIR LED as a lighting source, transparent and quick veins imaging as well as non-destructive testing were demonstrated, suggesting the NIR phosphor has a wide range of practical applications.     

Octahedron-dependent near-infrared luminescence in Cr3+-activated phosphors

Searching for broadband near-infrared (NIR) materials with high efficiency and excellent thermal luminescence stability is of great significance because of their widespread spectroscopic applications. Different element substitution can modulate the structure and crystal field of host lattice so as to regulate the luminescent properties. Herein, we report the octahedron-dependent NIR luminescence in Cr³⁺-doped KMP₂O₇ (M = Ga, Sc, In, and Lu) phosphors and investigate the effect of octahedral environment on luminescent properties, aiming to provide guidance for host material selection. The decreased crystal field strength leads to the apparent spectral red shift from 815 to 900 nm for the samples of M = Ga to Lu. The small Stokes shift as well as weak electron–phonon coupling effect decreases the non-radiative transition probability and thus gives rise to the highest emission intensity and excellent thermal stability of Cr³⁺-doped KGaP₂O₇. The optimal sample, KGa_0.89P₂O₇:0.11Cr³⁺, possesses an internal/external quantum efficiency of 55.8%/36.6%, and its integrated emission intensity at 423 K can maintain 68% of that at room temperature. Finally, we investigate the potential applications in non-destructive examination field by manufacturing a NIR phosphor-conversion light-emitting diode device.     

Cr3+:SrGa12O19: A Broadband Near‐Infrared Long‐Persistent Phosphor

Cr³⁺‐doped SrGa₁₂O₁₉ is demonstrated to be a broadband near‐infrared (650–950 nm) long‐persistent phosphor whose luminescence can last for more than 2 h after ultraviolet irradiation is stopped. Detailed analysis of the photoluminescence and thermoluminescence spectra and of the persistent decay behavior of the Cr³⁺‐doped SrGa₁₂O₁₉ samples indicate that the persistent energy transfer from the SrGa₁₂O₁₉ host to the Cr³⁺ ions and the filling and release of electrons into and from the shallow and deep traps through the conduction band is responsible for the long‐persistent phosphorescence.     

Optical energy storage properties of Sr<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript>,R<Superscript>3+</Superscript> persistent luminescence materials

The details of the mechanism of persistent luminescence were probed by investigating the trap level structure of Sr₂MgSi₂O₇:Eu²⁺,R³⁺ materials (R: Y, La-Lu, excluding Pm and Eu) with thermoluminescence (TL) measurements and Density Functional Theory (DFT) calculations. The TL results indicated that the shallowest traps for each Sr₂MgSi₂O₇:Eu²⁺,R³⁺ material above room temperature were always ca. 0.7 eV corresponding to a strong TL maximum at ca. 90 °C. This main trap energy was only slightly modified by the different co-dopants, which, in contrast, had a significant effect on the depths of the deeper traps. The combined results of the trap level energies obtained from the experimental data and DFT calculations suggest that the main trap responsible for the persistent luminescence of the Sr₂MgSi₂O₇:Eu²⁺,R³⁺ materials is created by charge compensation lattice defects, identified tentatively as oxygen vacancies, induced by the R³⁺ co-dopants.     

Molten-Salt-Assisted Annealing for Making Colloidal ZnGa2O4:Cr Nanocrystals with High Persistent Luminescence

Persistent luminescent nanocrystals (PLNCs) in the sub-10 nm domain are considered to be the most fascinating inventions in lighting technology owing to their excellent performance in anti-counterfeiting, luminous paints, bioimaging, security applications, etc. Further improvement of persistent luminescence (PersL) intensity and lifetime is needed to achieve the desired success of PLNCs while keeping the uniform sub-10 nm size. In this work, the concept of molten salt confinement to thermally anneal as-synthesized ZnGa₂O₄:Cr³⁺ (ZGOC) colloidal NCs (CNCs) in a molten salt medium at 650 °C is introduced. This method led to significantly monodispersed and few agglomerated NCs with a much improved photoluminescence (PL) and PersL intensity without much growth in the size of the pristine CNCs. Other strategies such as i) thermal annealing, ii) overcoating, and iii) the core–shell strategy have also been tried to improve PL and PersL but did not improve them simultaneously. Moreover, directly annealing the CNCs in air without the assistance of molten salt could significantly improve both PL and PersL but led to particle heterogeneity and aggregation, which are highly unsuitable for in vivo imaging. We believe this work provides a novel strategy to design PLNCs with high PL intensity and long PersL duration without losing their nanostructural characteristics, water dispersibility and biocompatibility.     

Synthesis,properties and mechanism of photodegradation of core–shell structured upconversion luminescent NaYF4:Yb3+,Er3+@BiOCl

Microspherical bismuth oxychloride (BiOCl) can only utilize ultraviolet (UV) light to promote photocatalytic reactions. To overcome this limitation, a uniform and thin BiOCl nanosheet was synthesized with a particle size of about 200 nm. As results of UV–visible diffuse reflectance spectroscopy showed, the band gap of this nanostructure was reduced to 2.78 eV, indicating that the BiOCl nanosheet could absorb and utilize visible light. Furthermore, the upconversion material NaYF₄ doped with rare earth ions Yb³⁺ and Er³⁺ emitted visible light at 410 nm following excitation with near‐infrared (NIR) light (980 nm), which could be utilized by BiOCl to produce a photocatalytic reaction. To produce a high‐efficiency photocatalyst (NaYF₄:Yb³⁺,Er³⁺@BiOCl), BiOCl‐loaded NaYF₄:Yb³⁺,Er³⁺ was successfully synthesized via a simple two‐step hydrothermal method. The as‐synthesized material was confirmed using X‐ray diffraction, scanning electron microscopy, X‐ray photoelectron spectroscopy as well as other characterizations. The removal ratio of methylene blue by NaYF₄:Yb³⁺,Er³⁺@BiOCl was much higher than that of BiOCl alone. Recycling experiments verified the stability of NaYF₄:Yb³⁺,Er³⁺@BiOCl, which demonstrated excellent adsorption, strong visible‐light absorption and high electron–hole separation efficiency. Such properties are expected to be useful in practical applications, and a further understanding of the NIR‐light‐responsive photocatalytic mechanism of this new catalytic material would be conducive to improving its structural design and function.     

A Multifunctional Biomaterial with NIR Long Persistent Phosphorescence,Photothermal Response and Magnetism

There are many reports on long persistent phosphors (LPPs) applied in bioimaging. However, there are few reports on LPPs applied in photothermal therapy (PTT), and an integrated system with multiple functions of diagnosis and therapy. In this work, we fabricate effective multifunctional phosphors Zn₃Ga₂SnO₈: Cr³⁺, Nd³⁺, Gd³⁺ with NIR persistent phosphorescence, photothermal response and magnetism. Such featured materials can act as NIR optical biolabels and magnetic resonance imaging (MRI) contrast agents for tracking the early cancer cells, but also as photothermal therapeutic agent for killing the cancer cells. This new multifunctional biomaterial is expected to open a new possibility of setting up an advanced imaging‐guided therapy system featuring a high resolution for bioimaging and low side effects for the photothermal ablation of tumors.     

An optical, EPR and electrical conductivity study of blue barium titanate, BaTiO3−δ

The electronic UV–VIS–NIR absorption spectra of single crystalline BaTiO_3−δ (BTO) are studied in the temperature range of 102–1173 K in pure oxygen and at conditions of moderate and strong reduction of the material. The strongly reduced crystals are of deep blue colour. The optical spectra of blue BTO are characterised by a strong absorption in the NIR region at around 7000 cm⁻¹, which is attributed to polaronic defects associated with the formation of Ti³⁺ in the material. This assumption is supported by fits of the spectra using polaronic line shape functions appropriate for disordered systems and also by the electrical conductivity of blue BTO which, in agreement with results from the optical spectra, exhibits an activation energy of 0.20 eV. The EPR spectra of moderately reduced BTO powders show an anisotropic g-factor, which is compatible with the optical spectrum. The temperature dependence of the band gap energy of BTO was found to be given as dE_g/dT = −7.21 × 10⁻⁴ eV/K.     

Characterization,EPR and photoluminescence studies of LiAl5O8:Cr phosphors

Red emitting Cr³⁺ doped LiAl₅O₈ powder phosphor was prepared by combustion route using corresponding metal nitrates and urea in a single step. The prepared powder was characterized by X-ray diffraction and surface area measurements were carried out by Brunauer–Emmet–Teller adsorption isotherms. The electron paramagnetic resonance spectrum in the low field regions is typical for isolated Cr³⁺ ions whereas the resonance signal in the high field region with g = 1.95 is due to exchange coupled Cr³⁺–Cr³⁺ pairs. The optical studies show two broad and intense bands characteristic of Cr³⁺ ions in distorted octahedral symmetry. The photoluminescence spectrum gives a narrow red emission at 710 nm corresponding to ²E_g → ⁴A_2g transition upon excitation of 562 nm. The crystal field parameter (Dq), Racah inter-electronic repulsion parameters (B and C) and nephelauxetic parameters have been evaluated and discussed.     

Fabrication and photoluminescence properties of Ag0 and Ag0–Er3+ containing plasmonic glass nanocomposites in the K2O–ZnO–SiO2 system

Here, we report the preparation of nano silver (Ag) and nano Ag-erbium (Ag–Er) co-embedded potassium–zinc-silicate based monolithic glass nanocomposites by a controlled heat-treatment process of precursor glasses. The nanocomposites were characterized by differential scanning calorimeter, dilatometer, UV–Visible absorption spectrophotometer, X-ray diffractometer and transmission electron microscope and spectroflurimeter. A strong surface plasmon resonance (SPR) band is observed around 430 nm in all the heat-treated glass nanocomposite samples due to the formation of Ag⁰ nanoparticles (NP). The Ag-glass nanocomposite samples display nearly 2-fold enhanced photoluminescence (PL) at 470 nm upon excitation at 290 nm until the size of the NP increases to the value equals to the mean free path of conduction electrons inside the particles. On contrary to this, the photoluminescence spectra of Er³⁺ ions exhibit a gradual decrease of NIR emission at 1540 nm due to ⁴I_13/2 → ⁴I_15/2 transition under excitation at 523 nm in the heat-treated glass nanocomposites which happened due to excitation energy transfer of Er³⁺ ions to the Ag NP, acting as ‘plasmonics diluents’ for Er³⁺ ions. These nanocomposites have huge potential for various nanophotonic applications.     

Oligo and polyuronic acids interactions with hypervalent chromium

Selective oxidation of galacturonic residues of oligo and polyuronic acids by Cr^VI affords CO₂/HCO₂H, oxidized uronic acid, and Cr^III as final redox products. Kinetic studies show that the redox reaction proceeds through a mechanism combining Cr^VI → Cr^IV → Cr^II and Cr^VI → Cr^IV → Cr^III pathways. The mechanism is supported by the observation of free radicals, CrO₂²⁺ and Cr^V as reaction intermediates. The EPR spectra show that five- and six coordinated oxo-Cr^V intermediates are formed. Penta-coordinated oxo-Cr^V species are present at any [H⁺], whereas hexa-coordinated ones are only observed at pH <1. At low pH Cr^V predominating species are coordinated by carboxylate groups and O^ring (g_iso = 1.9783/5). At pH 7.5, the predominating ones are those coordinated by alcoholate groups of the ligand (g_iso = 1.9800). Polygal can reduce Cr^VI and efficiently trap Cr^III. This behaviour represents an interesting model for the study of biomaterials, which possess a high proportion of polygal, in order to remove chromium from polluted waters.     

Effects of Sm Co-doping on Luminescent Properties of Sr4Al14O25:M (M=Mn4+, Cr3+) Phosphors

The Sr₄Al₁₄O₂₅:M and doped Sr₄Al₁₄O₂₅:M+Sm³⁺ (M=Mn⁴⁺, Cr³⁺) phosphors were syn-thesized by a solid-state reaction method and their luminescent properties were investi-gated. The results showed that the co-doping of Sm ions did not change the positions of excitation band and emission band but signi cantly improved the luminescent properties of Sr₄Al₁₄O₂₅:Cr³⁺ phosphors; whereas, the emission intensity of Sr₄Al₁₄O₂₅:Mn⁴⁺ was re-dueced remarkably when Sm ions were co-doped. In addtion, a radiative-form energy transfer from Sm³⁺ to Cr³⁺ was observed for the first time in the Cr, Sm co-doped Sr₄Al₁₄O₂₅ phos-phors. The results indicated that Sm ions could signi cantly improve the emission intensity of Sr₄Al₁₄O₂₅:Cr³⁺, making the Sm³⁺co-doped Sr₄Al₁₄O₂₅:Cr³⁺ phosphor a promising can-didate for the applications in display and solid state lightening.     

Photo-luminescence studies of strontium barium niobate crystals doped with Cr3+ ions

This paper reports the photo-luminescence spectroscopic results of Strontium–Barium–Niobate, Sr_x,Ba_1−xNb₂O₅ (SBN, x = 0.61 for near congruent composition) crystals doped with Cr₂O, at cryogenic temperature (20 K). The experimental results reveal the need of re-assignment of the Cr³⁺ ions defect centres in this material. For first time, a broad emission band in the near infrared region centred at ca. 950 nm is reported. This emission band has micro-seconds decaytime constant and a FWHM band-width > 1700 cm⁻¹ and has been ascribed to the vibronically assisted ⁴T₂ → ⁴A₂ transition. A much narrower emission band centred at ca. 764 nm with milli-seconds decaytime constant and a FWHM band-width of ca. 170 cm⁻¹ is correlated to the ²E → ⁴A₂ radiative transition (R-line).     

Non‐Aqueous Sol–Gel Synthesis of Ultra Small Persistent Luminescence Nanoparticles for Near‐Infrared In Vivo Imaging

Ultra‐small ZnGa₂O₄:Cr³⁺ nanoparticles (6 nm) that exhibit near‐infrared (NIR) persistent luminescence properties are synthesized by using a non‐aqueous sol–gel method assisted by microwave irradiation. The nanoparticles are pegylated, leading to highly stable dispersions under physiological conditions. Preliminary in vivo studies show the high potential for these ultra‐small ZnGa₂O₄:Cr³⁺ nanoparticles to be used as in vivo optical nanotools as they emit without the need for in situ excitation and, thus, avoid the autofluorescence of tissues.     

A novel Cr3+-activated far-red titanate phosphor: synthesis,luminescence enhancement and application prospect

Plant factory, a new agricultural planting technology, has emerged and rapidly grown in recent years, with phosphor conversion light emitting diodes (pc-LEDs) considered as the first choice of source light for the plant factory. In this study, a new type of Cr³⁺-activated Li₂MgTi₃O₈ phosphor (LMT: Cr³⁺) was synthesized by high temperature solid state method. X-Ray diffraction patterns showed that there was no detectable impurity in these samples. The photoluminescence spectra revealed that this phosphor can emit far-red light with the peak at 740 nm excited by ultraviolet and blue light, overlapped well with the P_FR. After introducing Zn²⁺ ions (LMT: Cr³⁺, Zn²⁺), the luminescence intensity increases by 46% mainly due to the increase of lattice distortion, and internal quantum yield was improved from 25.4% to 41.3% under 365 nm excitation. Finally, the pc-LED devices, consisting of 470 nm chip coated with the optimal phosphor, exhibited good luminescence and overlapping with P_FR. These results indicate that the LMT: Cr³⁺, Zn²⁺ phosphor has the potential application in modern agriculture.     

Surface characteristics of high corrosion resistant Ni–Nb–Zr–Ti–Ta glassy alloys for nuclear fuel reprocessing applications

This work firstly discovered that the Ni₆₀Nb₁₅Zr₅Ti₁₅Ta₅ metallic glass exhibits high corrosion resistance in boiling 6 N HNO₃ solutions with and without Cr⁶⁺ ions, which may be of great potential for nuclear fuel reprocessing applications. The high corrosion resistance of the alloy is due to the formation of the passive film composed exclusively of Nb⁵⁺ and Ta⁵⁺ cations after immersion in the solution without Cr⁶⁺ ions, and Nb⁵⁺, Ta⁵⁺ and Cr³⁺ cations after immersion in the solution with Cr⁶⁺ ions.     

Magnetic entropy change in perovskite manganites La0.7A0.3MnO3 La0.7A0.3Mn0.9Cr0.1O3 (A = Sr,Ba, Pb) and Banerjee criteria on phase transition

The La_0.7A_0.3MnO₃, La_0.7A_0.3Mn_0.9Cr_0.1O₃ (A = Sr, Ba, Pb) polycrystalline perovskite manganites sample was prepared by the sol–gel technique. The replacement of partial Mn³⁺/Mn⁴⁺ by Cr³⁺ (Cr³⁺ with the same electronic configuration as Mn⁴⁺) cause the variety of magnetocaloric property and magnetic entropy change. The maximum magnetic entropy change ΔS_H = −1.16 J/kg K and the Relative Cooling Power (about 43.3 J/kg) were obtained from La_0.7Sr_0.3Mn_0.9Cr_0.1O₃ in the Cr³⁺ doped series under 1 T magnetic field variation. On this paper, Banerjee criteria had been remarked to distinguish the first-order or second-order phase transition on phase transition of the doped perovskite manganites.     

Judd–Ofelt analysis and photoluminescence properties of RE3+ (RE = Er & Nd): Cadmium lithium boro tellurite glasses

Rare earth (Er³⁺ and Nd³⁺) ions doped cadmium lithium boro tellurite (CLiBT) glasses were prepared by melt quenching method. The vis–NIR absorption spectra of these glasses have been analyzed systematically. Judd–Ofelt intensity parameters Ω_λ (λ = 2, 4, 6) have been evaluated and used to compute the radiative properties of emission transitions of Er³⁺ and Nd³⁺: CLiBT glasses. From the NIR emission spectra of Er³⁺: CLiBT glasses a broad emission band centered at 1538 nm (⁴I_13/2 → ⁴I_15/2) is observed and from Nd³⁺: CLiBT glasses, three NIR emission bands at 898 nm (⁴F_3/2 → ⁴I_9/2), 1070 nm (⁴F_3/2 → ⁴I_11/2) and 1338 nm (⁴F_3/2 → ⁴I_13/2) are observed with an excitation wavelength λ_exci = 514.5 nm (Ar⁺ Laser). The FWHM and stimulated emission cross-section values are calculated for Er³⁺ and Nd³⁺: CLiBT glasses. FWHM × σ_e^P values are also calculated for Er³⁺: CLiBT glasses.