Simultaneous Spectrophotometric Determination of Cadmium, Zinc and Copper with Kalman Filter

The compound 2-QADNm can form red complexes with caamium(II), zinc(II) and copper(II). The simultaneous determination of cadmium, zinc and copper with Kalman Filter is described in this paper, the proposed method was applied to a two-component system for determining cadmium and copper,and a three-component system for determining cadmium, zinc and copper.     

Ion-pair formation of a copper(II)-ammine complex with an anionic surfactant and the recovery of copper(II) from ammonia medium by the surfactant-gel extraction method.

The extraction and separation of copper(II), zinc(II), cobalt(II), and cadmium(II) were investigated. Both copper(II) and zinc(II) formed ammine-complexes, while cadmium(II) and cobalt(II) formed hydroxide precipitates in an ammonia medium. By the addition of sodium dodecylsulfate (SDS), a copper(II) complex formed an ion-pair (copper-ammine-DS), which was extracted into the SDS phase. However, a zinc(II) complex did not form an ion-pair, and was soluble in water. Copper(II) ion was recovered by stripping (back-extraction) after the addition of hydrochloric acid. This method was applied to the separation of copper(II) in a brass alloy.     

meso-四(3-氟-4-磺酸基苯基)卟啉的合成及微分分光光度法同时测定痕量铜锌

本文报道一种新的高灵敏度水溶性卟啉显色剂meso-四(3-氟-4-磺酸基苯基)卟啉的合成方法. 研究了该试剂与Cu(II)、Zn(II)的反应条件. 在PH6.4的HOAc-NaOAc缓冲介质中, Hg(II)催化下, 室温反应30min即完成. 采用四阶微分分光光度法可同时测定痕量Cu(II)、Zn(II). 表观微分摩尔吸光系数分别达8.13×10^5和1.59×10^6. 本方法灵敏度高, 选择性好, 可不用分离直接测定茶叶、血液等样品中痕量Cu(II)、Zn(II), 操作简便.     

H-point standard addition method for simultaneous determination of cobalt(II) and zinc(II) ions

The H-point standard addition method (HPSAM) was applied to the simultaneous determination of zinc(II) and cobalt(II). This method is based on the difference in the absorbance of methylthymol blue complexes of Zn(II) and Co(II) at pH 6 buffered solution in different wavelength pairs. The results showed that Zn(II) and Co(II) can be determined simultaneously with concentration ratios of 20:1 and 1:7.5. Under working conditions, the proposed method was successfully applied to the simultaneous determination of zinc and cobalt in synthetic and real samples.     

Apoenzymes of Alkaline Phosphatases of Different Origin for Determining of Trace Zinc(II)

The applicability of the apoenzymes of three alkaline phosphatases of different origin (bacterial from E. coli and animal from chicken intestine or the small intestine of a Greenland seal) to the determination of zinc(II) was studied. The alkaline apophosphatase from seal intestine was found to be promising for this purpose. The preparation conditions of the apoenzyme and the conditions of its reactivation with zinc(II) were optimized. Based on the reactivating effect of zinc(II) on the apoenzyme, which was prepared with the use of EDTA, an enzymatic method was developed for determining zinc(II) (0.01–0.1 g/mL) with c _min = 8 ng/mL. The proposed procedure was applied to the determination of zinc(II) in blood serum.     

H-point standard addition method for simultaneous determination of cobalt(II) and zinc(II) ions

The H-point standard addition method (HPSAM) was applied to the simultaneous determination of zinc(II) and cobalt(II). This method is based on the difference in the absorbance of methylthymol blue complexes of Zn(II) and Co(II) at pH 6 using different wavelength pairs. The results showed that Zn(II) and Co(II) can be determined simultaneously with concentration ratios of 20:1 and 1:7.5. Under working conditions, the proposed method was successfully applied to the simultaneous determination of zinc and cobalt in synthetic, drinking water and vitamin samples.     

REGIOSELECTIVE PHOTOREDUCTION OF ZINC(II) PORPHYRINS TO GIVE CHLORINS

The ascorbic acid/organic base photoreduction of zinc(II) porphyrins was investigated. It was established that certain substituents can direct the photoreduction to the site of the macrocycle to which they are attached. For example, zinc(II) vinylporphyrins (8, 12, 16, 20) are photoreduced with cis stereochemistry on the ring bearing the vinyl group to give the corresponding chlorins. Zinc(II) acetylporphyrins (22, 24) were likewise reduced to chlorins such that cis-hydrogenation took place on the ring bearing the acetyl group. Zinc(II) formylporphyrins 33 also appear to reduce at the ring bearing the formyl group. When the zinc(II) acrylic porphyrin 28 was photoreduced, reduction did take place at the ring bearing the acrylic side chain, but migration of the acrylate double bond was very rapid, and the product isolated was the corresponding porphyrin propionate 30. Reduction of a zinc(II) porphyrin 35 bearing both a vinyl group and a nuclear carboxylic ester took place at the ring bearing the carboxylic ester. The reaction provides a general method for regioselective synthesis of chlorins from zinc(II) porphyrins without any evidence of formation of over-reduction products characteristic of many other procedures for formation of chlorins from porphyrin precursors.     

Use of the differential pulse cathodic adsorptive stripping voltammetric method for the simultaneous determination of trace amounts of cadmium and zinc

A selective and sensitive method for the determination of cadmium and zinc is presented. The method is based on the adsorptive accumulation of the complexes of Cd(II) and Zn(II) ions with 4-amiono-5-methyl-2.4-dihydro-3H-1,2,4-triazol-3-tion (MMTT) onto hanging mercury drop electrode (HMDE), followed by the reduction of the adsorbed species using a voltammetric scan using differential pulse modulation. The ligand concentration, pH, potential and time of accumulation, scan rate, and pulse height were optimized. Under the optimized conditions, a linear calibration curve was obtained for the concentration of Cd(II) and Zn(II) in the range of 5–450 and 5–850 ng/mL, respectively, with a detection limit of 1.7 ng/mL Cd(II) and 1.3 ng/mL Zn(II). The ability of the method was evaluated by analysis of cadmium and zinc in water and alloy samples The text was submitted by the authors in English.     

Deprotonation of zinc(II)-water and zinc(II)-alcohol and nucleophilicity of the resultant zinc(II) hydroxide and zinc(II) alkoxide in double-functionalized complexes: theoretical studies on models for hydrolytic zinc enzymes

The factors governing the deprotonation ability of zinc(II)-water and zinc(II)-alcohol and nucleophilicity of the resultant zinc(II) hydroxide and zinc(II) alkoxide as complex models for zinc enzymes have been investigated through Hartree-Fock and density-functional theory methods with the 6-311++G(d,p) basis set. Our calculations showed that in these double-functionalized complexes (i.e., zinc complexes having both a zinc(II)-alcohol motif and a zinc(II)-water motif) zinc(II)-alcohol is preferred in deprotonation over zinc(II)-water (i.e., zinc(II)-alcohol has a much lower pK(a) than zinc-coordinated water in the same molecule). Natural bond orbital analysis revealed that zinc(II) alkoxides are more nucleophilic than their respective counterparts zinc(II) hydroxides. The analysis of the transition state in the transformation reaction from zinc(II) hydroxide species to zinc(II) alkoxide species indicates that zinc(II) alkoxides are the preferred deprotonated species not only thermodynamically but also kinetically. Further examination of the proposed mechanisms of the zinc(II) alkoxide-promoted transesterification path and the zinc(II) hydroxide-promoted hydrolysis path revealed the structures of the intermediates and energy diagrams in the reactions. These results, entitled double-functionalized complexes, for the first time, put a firm theoretical foundation of why the zinc(II)-alcoholic OH is a better model for hydrolytic zinc enzymes (having both stronger acidity and better nucleophilicity).     

Can Co(II) or Cd(II) substitute for Zn(II) in zinc fingers?

Zinc finger domains consist of sequences of amino acids containing cysteine and histidine residues tetrahedrally coordinated to a zinc ion. The role of zinc in a DNA binding finger was considered purely structural due to the absence of redox chemistry in zinc. However, whether other metals e.g. Co(II) or Cd(II) can substitute Zn(II) is not settled. For an answer the detailed interaction of Co(II) and Cd(II) with cysteine methylester and histidine methylester has been investigated as a model for the zinc core in zinc fingers. The study was extended to different temperatures to evaluate the thermodynamic parameters associated with these interactions. The results suggest that zinc has a unique role.     

Quantitative separation of zinc traces from cadmium matrices by solid-phase extraction with polyurethane foam

A system for separation of zinc traces from large amounts of cadmium is proposed in this paper. It is based on the solid-phase extraction of the zinc in the form of thiocyanate complexes by the polyurethane foam. The following parameters were studied: effect of pH and of the thiocyanate concentration on the zinc extraction, shaking time required for quantitative extraction, amount of PU foam necessary for complete extraction, conditions for the separation of zinc from cadmium, influence of other cations and anions on the zinc sorption by PU foam, and required conditions for back extraction of zinc from the PU foam. The results show that zinc traces can be separated from large amounts of cadmium at pH 3.0±0.50, with the range of thiocyanate concentration from 0.15 to 0.20 mol l⁻¹, and the shaking time of 5 min. The back extraction of zinc can be done by shaking it with water for 10 min. Calcium, barium, strontium, magnesium, aluminum, nickel and iron(II) are efficiently separated. Iron(III), copper(II) and cobalt(II) are extracted simultaneously with zinc, but the iron reduction with ascorbic acid and the use of citrate to mask copper(II) and cobalt(II) increase the selectivity of the zinc extraction. The anions nitrate, chloride, sulfate, acetate, thiosulphate, tartarate, oxalate, fluoride, citrate, and carbonate do not affect the zinc extraction. Phosphate and EDTA must be absent. The method proposed was applied to determine zinc in cadmium salts using 4-(2-pyridylazo)-resorcinol (PAR) as a spectrophotometric reagent. The result achieved did not show significant difference in the accuracy and precision (95% confidence level) with those obtained by ICP–AES analysis.     

Selective back-extraction and preconcentration of zinc(II) from metal-1,3,5-triketone extracts prior to its determination by flame atomic absorption spectrometry

A simple back-extraction method was developed for the separation and preconcentration of trace levels of zinc from different matrices. Ethyl-2-(4-methoxybenzoyl)-3-(4-methoxyphenyl)-3-oxopropanoylcarbamate (EMPC) was used as a new complexing agent for the extraction of zinc(II) from the aqueous sample phase to the methyl isobutyl ketone (MIBK) phase as Zn(EMPC)₂ complexes. The Zn(II) can be selectively stripped with 1?mL of 0.5?mol?L^?1 HCl from Mⁿ⁺(EMPC)_n complexes [Ag(I), Al(III), Cd(II), Cr(III), Cu(II), Fe(II), Fe(III), Mn(II), Ni(II), Pb(II) and Pd(II)] which dissolved in MIBK phase. Some experimental parameters, which are important for the whole extraction process, including pH, sample volume, shaking time, amount of the EMPC reagent, amount of MIBK, ionic strength, and type of back-extractant were investigated. The recovery for Zn(II) was greater than 95%. The detection limit of the method was found to be 0.2?µg?L ^{? 1} and the relative standard deviation as 6.4%. The concentrations of Zn(II) in the certified reference materials (LGC6019 river water and NIST-1547 peach leaves) by the presented method were in good agreement with the certified values. The proposed method was succesfully applied to the determination of zinc in some natural waters, rice, hair, soil, and tea samples.     

Photofunctionality in Porphyrin‐Hybridized Bis(dipyrrinato)zinc(II) Complex Micro‐ and Nanosheets

New bis(dipyrrinato)zinc(II) complex micro‐ and nanosheets containing zinc(II) porphyrin ( N2 ) are synthesized. A liquid/liquid interface method between dipyrrin porphyrin ligand L2 and zinc acetate produces N2 with a large domain size. N2 can be layered quantitatively onto a flat substrate by a modified Langmuir–Schäfer method. N2 deposited on a SnO₂ electrode functions as a photoanode for a photoelectric conversion system. The photoresponse of N2 covers the whole visible wavelength range (400–650 nm), with a maximum quantum efficiency of more than twice that of a bis(dipyrrinato)zinc(II) complex nanosheet without porphyrin.     

Determination of zinc in pharmaceutical products using an electrodialyser incorporated into a flow system

An electrodialyser unit has been designed, incorporated into the conduits of a flow injection (FI) system, and employed for the removal of interferences in the determination of zinc(II) in multivitamin tablets. The proposed system is fully computerised and is able to determine zinc(II) at a frequency of 18 samples/h with a sample interaction of 0.0015%. The calibration graph is linear between 1 and 20 mg/L. The detection limit is 0.998 mg/L. The results obtained for zinc(II) in multivitamin tablets with the proposed system compared favourably with those obtained with the standard manual AAS method.     

Ion-exchanger colorimetry-III microdetermination of zinc in water

An ion-exchanger colorimetric method for the determination of zinc(II) with Zincon has been developed. Zinc in a water sample can be determined by sorption onto an anion-exchange resin from 2M chloride solution followed by transformation into a coloured complex with Zincon. With use of a 1-litre sample the sensitivity is 10 times greater than that for conventional colorimetry. Most metals, except cadmium(II), lead(II) and bismuth(III), do not interfere when present in up to 100 times the concentration of zinc. The zinc: Zincon ratio of the complex in the resin phase was found to be 1 : 1 by the molar ratio method.     

Functionalization of cross linked chitosan with 2-aminopyridine-3-carboxylic acid for solid phase extraction of cadmium and zinc ions and their determination by atomic absorption spectrometry

We have developed a new method for solid phase extraction (SPE) and preconcentration of trace amounts of cadmium and zinc using cross linked chitosan that was functionalized with 2-aminopyridine-3-carboxy acid. Analytical parameters, sample pH, effect of flow rate, sample volume, and concentration of eluent on column SPE were investigated. The effect of matrix ions on the recovery of cadmium and zinc has been investigated and were found not to interfere with preconcentration. Under the optimum experimental conditions, the preconcentration factors for Cd(II) and Zn(II) were found to be 90. The two elements were quantified via atomic absorption spectrometry. The detection limits for cadmium and zinc are 21 and 65?ng?L^?1, respectively. The method was evaluated by analyzing a certified reference material (NIST 1643e; water) and has been successfully applied to the analysis of cadmium and zinc in environmental water samples.

Determination of zinc in pharmaceutical products using an electrodialyser incorporated into a flow system

An electrodialyser unit has been designed, incorporated into the conduits of a flow injection (FI) system, and employed for the removal of interferences in the determination of zinc(II) in multivitamin tablets. The proposed system is fully computerised and is able to determine zinc(II) at a frequency of 18 samples/h with a sample interaction of 0.0015%. The calibration graph is linear between 1 and 20 mg/L. The detection limit is 0. 998 mg/L. The results obtained for zinc(II) in multivitamin tablets with the proposed system compared favourably with those obtained with the standard manual AAS method.     

Kinetically controlled separation of cadmium(II) from zinc(II) with dithizone in the presence of nitrilotriacetic acid.

The extraction rates of cadmium(II) and zinc(II) with dithizone (H2dz) in the presence of nitrilotriacetic acid (NTA) were measured, and the possible kinetic separation of cadmium(II) from zinc(II) was investigated. Upon the addition of NTA, the difference in the extraction rate between cadmium(II) and zinc(II) became large. Based on the observed rate constant under the condition [NTA] = 1 x 10(-2) mol dm-3, [H2dz]org = 1 x 10(-3) mol dm-3, and pH = 7.0, the shaking time required for the quantitative separation of cadmium(II) from zinc(II) was calculated to be between 326 and 995 s. The experimental results agreed with the prediction, and the quantitative separation of cadmium(II) from zinc(II) was performed within the above-mentioned range of shaking times.     

The synthesis and fluorescent properties of analogues of the zinc(II) specific fluorophore zinquin ester

The synthesis and fluorescent properties in the absence and presence of zinc(II) of a range of 2-substituted derivatives of N-(6-methoxy-2-methyl-8-quinolyl)-4-methylbenzenesulfonamide are described. These analogues formed complexes with zinc(II) as indicated by a bathochromic shift in their UV/vis spectra. Analogues with isobutenyl and isobutyl side chains at the 2-position formed fluorescent complexes whose fluorescence was stronger than that of the 2-methyl-containing parent. These derivatives were converted, via conversion to the phenol with boron tribromide and reaction with ethyl bromoacetate, to systems with ester-containing side chains analogous to zinquin ester, a specific cellular fluorophore for zinc(II). All of these ester derivatives formed complexes with zinc(II) resulting in a bathochomic shift in their UV/vis spectra. Compounds with isobutyl, isobutenyl, and styryl side chains exhibited increased fluorescence compared to that of zinquin ester in the presence of zinc(II). The compound with the 2-isobutyl side chain was more selective in its fluorescence for zinc(II) over cadmium(II) compared to zinquin ester.