Triplet quenching and antioxidant effect of several carbon black grades in the photodegradation of LDPE doped with benzophenone as a photosensitiser

In a previous paper it was demonstrated for the first time, that carbon black pigments have the ability to operate as effective singlet and triplet quenchers. This work was undertaken directly in the polymer using the inherent long-lived luminescent species as triplet donor species. In order to ascertain the effectiveness of the quenching mechanism and its inter-relationship with carbon black parameters, a total of eight different carbon black pigments have been incorporated into low density polyethylene at different concentrations (0.1, 0.2, 0.4% w/w) and their effects determined on the quenching the triplet state of a known triplet photosensitiser, benzophenone (0.05% w/w). Using phosphorescence analysis at 77 K a large variability was observed in the benzophenone triplet lifetime quenching, the effect varying with the pigment type and the concentration of pigment. Photodegradation rates on the films were also performed in order to relate the quenching effect of the carbon black with films exposed to UVA light at 70°C. An unusual synergistic effect between the carbon black and the benzophenone sensitiser was observed compared with films containing only carbon black. The implications of carbon black pigments to operate as “super quenchers”, as well as antioxidants in this study and under practical concentration conditions is discussed. Although not consistent throughout, there is some indication that low surface area carbon black pigments can be the most effective quenchers of active excited states. However, the presence of surface containing oxygen groups can be related to the synergistic effect reported, using experimental design statistical analysis.     

Specifics of localization of carbon black at the interface between polymeric phases

The thermodynamic and kinetic factors that determine the localization of carbon black particles at interfaces in polymer blends were established. Substantial differences in particle localization conditions at the interfaces of two high-molecular-mass or low-molecular-mass liquids were revealed; these differences are manifested in the determining effect of the sequence of mixing of the filler with the polymeric components of the blend on the localization. The effect is explained in terms of nonequilibrium positions of carbon black particles at the interface. This nonequilibrium distribution is primarily due to a high energy of desorption of macromolecules from the solid surface.     

Structure of the carbon-black-particles framework in filled elastomer materials

Specific features of the structure of a rigid framework composed of aggregated carbon black particles in rubber were considered. The volume fractions of the main components of the material—the filler, the binder, the layer enveloping carbon black particles, and the polymer entrapped by aggregates—were calculated. It was found that the volume fraction of the polymer in the layer around filler particles can be very high. The average number of contacts between neighboring aggregates in rubber with a high filler content is six. During deformation, the structure undergoes strong changes, so that neighboring aggregates can move from each other or, conversely, the remote aggregates can approach each other.     

Grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticle and carbon black surfaces

The surface grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticles and carbon black was investigated. The grafting of hyperbranched cyclotriphosphazene polymer onto these surfaces was achieved by the repeated reactions of hexachlorocyclotriphosphazene with hexamethylenediamine from surface amino groups and sodium carboxylate groups, respectively. The percentage of grafting onto silica and carbon black surfaces exceeded 760 and 390%, respectively. However, it proved difficult to achieve the theoretical growth of cyclotriphosphazene polymer from these surfaces because of steric hindrance. The introduction of sulfonic acid groups was successfully achieved by the reaction of terminal chlorophosphazene groups of the hyperbranched polymer‐grafted silica and carbon black with sulfanilic acid. The content of sulfonic acid groups introduced onto silica and carbon black surfaces was 4.98 mmol/g and 5.70 mmol/g, respectively. The sulfonated cyclotriphosphazene polymer‐grafted carbon black was extremely hydrophilic, yielding stable colloidal dispersions in polar solvents. The sulfonated cyclotriphosphazene polymer‐grafted silica and carbon black showed ionic conductivity, with the conductance increasing exponentially with increasing relative humidity and temperature. This study may offer important leads in the application of silica nanoparticles and carbon black in polymeric membranes for fuel cells. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4218–4226, 2008     

Morphology of polyethylene–carbon black composites

Carbon black is a common polymer additive that is used for reinforcement and for its ability to enhance physical properties, such as conductivity. This article pertains to an X‐ray scattering (SAXS) study of a conductive grade of carbon black and carbon black–polymer composites. The scattering pattern for such blacks displays a surface‐fractal‐like power‐law decay over many decades in scattering vector q. It is often assumed that small‐angle scattering from carbon black aggregates can be described in terms of surface‐fractal models, related to particles with fractally rough surfaces. Such self‐similar surface roughness is usually easy to identify by microscopy; however, electron microscopy from these blacks fails to support this assumption. It is proposed here that this apparent surface‐fractal scattering actually represents a more complicated morphology, including overlapping structural features and a power‐law scaling of polydispersity. One use of conductive black–polyethylene composites is in circuit protection devices where resistive heating leads to a reversible association of carbon black aggregates that controls switching between a conductive and a nonconductive state. Scattering can be used as an in situ tool to observe the morphological signature of this reversible structural change. Scattering patterns support a model for this switching based on local enhancement of concentration and the formation of linear agglomerates associated with the matrix polymer's semicrystalline morphology. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1105–1119, 1999     

Conductive Composites Based on Metallocene Isotactic Poly(propylene): Preparation and Properties

Summary: The research deals with the preparation and the further comprehensive characterization of metallocene polypropylene-based composite materials by incorporation of carbon black nanoparticles. Composites containing up to 10 wt% of carbon black were prepared by direct melt mixing in a single screw extruder Brabender Extrusiograph type 30/25D with attached static mixer at melt temperature of 200 °C and a screw speed of 30 rpm, according to a two-step process. Some composites were treated with 3 wt% maleic anhydride grafted polypropylene (MAH-PP). The rheological behaviour of the miPP nanocomposites was determined by cone/plate rheological measurements at 180 °C. The composites were characterized by SEM for morphological details and uniaxial stress-strain measurements for determining the mechanical parameters. Electric conductivity of injection molded plates from these composites was investigated. The different miPPs studied are ranked in an ascending order according to their increasing molecular weight concerning the magnitude of their rheological parameters. The maleic anhydride compatibilizer leads to lower viscosity values even at high shear gradients and to better homogenization of the nanofiller in the polymer matrix. The processing conditions, carbon black concentration and viscosity of the virgin polymer have an impact on the final conductivity of the miPP/carbon black composites.     

Cationic ring-opening isomerization polymerization of spiro orthocarbonates initiated by carbon black

The ring-opening isomerization polymerization of spiro orthocarbonates (SOC), such as 2,8-dimethyl-1,5,7,11-tetraoxaspiro[5.5]undecane ( I ), 8,10,19,20-tetraoxaspiro[5.2.2.5.2.2]-heneicosane-2,4-diene ( II ), and 8,10,19,20-tetraoxaspiro[5.2.2.5.2.2]heneicosane ( III ), initiated by carbon black was investigated. No polymerization of SOC was initiated in the absence of carbon black. But in the presence of channel black having a carboxyl group, the polymerization of SOCs was initiated at 90–150°C to give the corresponding polyether carbonates. The initiating ability of carbon black increased with an increase in its carboxyl group content. Furnace black having no carboxyl group failed to initiate the polymerization. Based on these results, it was concluded that the carboxyl group on carbon black is capable of initiating the polymerization of SOC. During the polymerization, a part of the polymers formed was grafted onto carbon black surface via the termination of growing polymer chains. The percentage of grafting increased with an increase in conversion and reached about 55%. Furthermore, polyether carbonate-grafted carbon black was found to produce a stable colloidal dispersion in chloroform. The mechanism of initiation and grafting were discussed.     

Cationic ring-opening transfer polymerization of spiro ortho esters initiated by carbon black

The ring-opening transfer polymerization of spiro ortho esters (SOE) initiated by carbon black was investigated. In the absence of carbon black, no polymerization occurred at all. In the presence of channel black containing carboxyl group, the ring-opening transfer polymerization of SOE was initiated at 50-70°C. to give polyether ester, namely alternating copolymer of epoxide and lactone. The rate of polymerization of 1,4,6-trioxaspiro[4.4]nonane and 1,4,6-trioxaspiro[4.5]decane was considerably small compared with that of 1,4,6-trioxaspiro[4.6]undecane. The activation energy of the polymerization of 2-chloromethyl-1,4,6-trioxaspiro[4.6]undecane was estimated to be 6.0 kcal/mol. The initiating activity of carbon black increased with an increase in carboxyl group content of carbon black. Furnace black that contained no carboxyl group was unable to initiate the polymerization. Furthermore, the carbon black lost the initiating ability of the polymerization upon the blocking of carboxyl group on the surface by the treatment with potassium hydroxide or diazomethane. Based on these results, it was concluded that carboxyl group on carbon black plays an important role in the initiation. During the polymerization, a part of the polymer formed was grafted onto carbon black: the grafting ratio was 10–30%. The mechanisms of initiation and grafting were discussed.     

Structure and dynamics of carbon black‐filled elastomers

The linear and nonlinear melt viscoelastic properties for a series of carbon black‐filled polymer composites were studied. Complementary tapping‐mode atomic force microscopy (AFM) studies were used to examine the dispersion and structural correlations of the filler particles in these composites. The low‐frequency dependence of the linear viscoelastic moduli gradually changes from liquidlike behavior for the unfilled polymer to pseudosolid character for composites with more than 9 vol % carbon black filler. The plateau modulus, inferred from the linear viscoelastic response, exhibits a somewhat discontinuous change at about 9 vol % filler. On the basis of the linear viscoelastic response, we postulate that the carbon black filler forms a continuous percolated network structure beyond 9 vol % filler, considerably lower than that expected from theoretical calculations for overlapping spheres and ellipsoids. We suggest that the lower threshold for percolation is due to the polymer mediation of the filler structure, resulting from the low functionality of the polymer and, consequently, few strong polymer–filler interactions, allowing for long loops and tails that can either bridge filler particles or entangle with one another. Furthermore, the strain amplitude for the transition from linear behavior to nonlinear behavior of the modulus for the composites with greater than 9 vol % filler is independent of frequency, and this critical strain amplitude decreases with increasing filler concentration. Complementary AFM measurements suggest a well‐dispersed carbon black structure with the nearest neighbor distance showing a discontinuous decrease at about 9 vol % filler, again consistent with the formation of a filler network structure beyond 9 vol % carbon black. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 256–275, 2001     

Polymer-mediated synthesis of highly dispersed Pt nanoparticles on carbon black

A new method was developed to prepare highly dispersed Pt nanoparticles on carbon black to use as proton exchange membrane (PEM) fuel cell catalysts. This method involves using a polymer, poly(vinylpyrrolidone) (PVP), to prevent particle aggregation and thereby reduce nanoparticle sizes to achieve high dispersion. It was found that Pt nanoparticles mediated by PVP are smaller than those obtained without PVP and have a narrower size distribution. Well-dispersed Pt nanoparticles with metal loadings from 5 to 35 wt % were obtained on carbon black (Vulcan XC-72R). It was found that well-dispersed Pt nanoparticles on carbon black could be synthesized at a PVP monomers-to-Pt atoms ratio of 0.1 under our experimental conditions. Larger amounts of PVP did not produce smaller nanoparticles, but rather reduced the Pt mass loading on carbon black. The morphology of the Pt nanoparticles that were supported on carbon black was characterized with transmission electron microscopy and X-ray diffraction. Their active surface areas were determined using cyclic voltammetry in a sulfuric acid solution. High Pt dispersion was obtained for the catalysts synthesized with PVP mediation, even at Pt loadings up to 35 wt %. The catalysts prepared with PVP mediation generally showed larger active specific areas than did those prepared without PVP.     

Ring opening during the cationic polymerization of 2-methylene-1,3-dioxepane: Cyclic ketene acetal initiation with sulfuric acid supported on carbon

The stable cyclic ketene acetal, 2-methylene-1,3-dioxepane, 7, has been polymerized cationically in pentane, CH₂Cl₂ and THF at 25°C to form a polymer which is composed of both ring-opened (40–50%) and ring-retained (50–60%) structures. Initiation was catalyzed by using H₂SO₄-supported on activated carbon black. This unique outcome differs significantly from the cationic polymerization of several other five- and six-membered ring cyclic ketene acetals which gave 100% 1,2-vinylpolymerization under these conditions. As the polymerization temperature increased in cationic polymerization of 7 the ring-opened content increased and the molecular weight of the polymers decreased in such solvents as cyclohexane, 1,2-dichloroethane, dimethoxyethane, and bis-(2-methoxyethyl) ether. The mechanism of this polymerization is discussed. This research also illustrated the ability to initiate the cationic polymerization of cyclic ketene acetals by acidified carbon black while avoiding subsequent polymer decomposition. © 1997 John Wiley & Sons, Inc.     

Living cationic polymerization of isobutyl vinyl ether by the carboxyl group of the carbon black/zinc chloride initiating system

The effect of zinc chloride (ZnCl₂) on the cationic polymerization of isobutyl vinyl ether (IBVE) initiated by carboxyl groups on a carbon black surface was investigated. Although the polymerization of IBVE was initiated by carboxyl groups on the surface, the rate of polymerization was small and the molecular weight distribution (MWD) of poly IBVE was very broad. The rate of the polymerization was found to be drastically increased, and 100% monomer conversion was achieved in a short time by the addition of ZnCl₂. The number-average molecular weights (M_n) of the polyIBVE were directly proportional to monomer conversion in the polymerization initiated by the carbon black/ZnCl₂ system. By addition of the monomer at the end of the first-stage polymerization, the added monomer was smoothly polymerized at the same rate as in the first stage. The M_n of the polymer was in excellent agreement with the calculated value, assuming the polyIBVE chain forms per unit carboxyl group on the surface and MWD was narrow (M_w/M_n = 1.2 ～ 1.3). Based on the results, it is concluded that carbon black/ZnCl₂ system has an ability to initiate the living cationic polymerization of IBVE. Furthermore, it was found that polyIBVE was grafted onto the carbon black surface after the quenching of the living polymer with methanol. © 1995 John Wiley & Sons, Inc.     

Radical Graft Polymerization of Vinyl Monomers Initiated by A20 Groups Introduced Onto a Carbon Black Surface: Effect of azo Groups on Graft Polymerization

The radical graft polymerization of vinyl monomers from carbon black initiated by azo groups introduced onto the surface was investigated. The introduction of azo groups onto carbon black surface was achieved by three methods: the reaction of 2,2′-azobis[2-(2-imidazolin-2-yl)propane] (AIP) with (1) epoxide groups, which were introduced by the reaction of carbon black with chlorometh-yloxirane; (2) acyl chloride groups, which were introduced by the reaction of carboxyl groups on the surface with thionyl chloride; and (3) 3-chloroformyl-1-cyano-1-methylpropyl groups, which were introduced by the reaction of carbon black with 4,4′-azobis(4-cyanovaleric acid) and then thionyl chloride. The amount of azo groups introduced onto the surface by the above methods was determined to be 0.07-0.19 mmol/g. The graft polymerization of methyl methacrylate was found to be initiated by azo groups introduced onto the carbon black surface. During the polymerization, poly(methyl methacrylate) was effectively grafted onto carbon black through propagation of the polymer from the radical produced on the surface by the decomposition of the azo groups. The percentage of grafting using carbon black having azo groups introduced by method 1 increased to 40%. It was also found that the graft polymerization of several vinyl monomers such as styrene, acrylonitrile, and acrylic acid was initiated by the azo groups introduced onto the surface and the corresponding polymer was effectively grafted onto the surface. Furthermore, the effect of the amount of carbon black having azo groups on the graft polymerization was investigated.     

LDPE／CPE／炭黑三相复合导电体系的亚微形态和导电性能

对ＬＤＰＥ／ＣＰＥ／炭黑三相复合导电体系的亚微形态和导电性能进行了研究。实验发现,该体系的亚微形态在共混比ＬＤＰＥ／ＣＰＥ大于和小于５０／５０时为典型的“海－岛”结构,在５０／５０时,为两相连续交错“互锁”结构;在共混比大于５０／５０时,ＬＤＰＥ／ＣＰＥ炭黑复合体系的导电性能较单一的ＬＰＤＰＥ树脂与炭黑复合体系的高２－５个数量级。     

Effect of silane coupling agent on the polymer‐filler interaction and mechanical properties of silica‐filled NR

The effects of filler loading and a new silane coupling agent 3‐octanoylthio‐1‐ propyltriethoxysilane (NXT silane) on the polymer‐filler interaction and mechanical properties of silica‐filled and carbon black‐filled natural rubber (NR) compounds were studied. Silica (high dispersion silica7000GR, VN2, and VN3) and carbon black (N330) were used as the fillers, and the loading range was from 0 to 50 phr. The loading of NXT silane was from 0 to 6 phr. Experimental results show that the maximum and minimum torques of silica and carbon black‐filled NR increase with increasing filler loading. With increasing filler loading, the scorch time and optimum cure time decrease for carbon black‐filled NR, but increase for silica‐filled NR. The minimum torque, scorch time, and optimum cure time decrease because of the presence of NXT silane. For the carbon black and silica‐filled NR, the tensile strength and elongation at break have maximum values, but the hardness, M300, M100, and tear strength keep increasing with filler loading. The mechanical properties of silica‐filled NR were improved in the presence of NXT silane. With increasing filler loading, the storage modulus of filled NR increases, but the loss factor decreases. Carbon black shows the strongest polymer‐filler interaction, followed by VN3, 7000GR, and VN2. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 573–584, 2005     

Encapsulation and dispersion of carbon black by an in situ controlling radical polymerization of AA/BA/St with DPE as a control agent

In this paper, a new strategy to encapsulate and disperse carbon black by an in situ controlling free radical polymerization of 1,1-Diphenylenthyene (DPE) method was developed. Firstly, a living amphipathic precursor polymer of P (AA-BA) containing DPE unit was synthesized. This precursor could be grafted or absorbed on the surface of small carbon black particles to prevent further aggregation of carbon black. And the DPE unit in the living amphipathic precursor could initiate following monomer to form polymer shell via in situ polymerization. Carbon black/polymer core-shell composite particles with 69.6 wt.% polymer shell were prepared. The encapsulated carbon black had a small particle size and high performance on dispersibility and stability. Encapsulation mechanism of this method was confirmed by analyses of TEM, UV–vis, ¹H NMR, ¹³C NMR, TGA, and other instruments.     

Effect of solvent and carbon black species on the rubber–carbon black interactions studied by pulsed NMR

The spin–spin relaxation time T₂ and the fraction of short T₂ component for composites of natural rubber with carbon black prepared under various conditions have been measured by pulsed NMR. Effect of swelling with a solvent (CCl₄), carbon black species (SAF, HAF, SRF) with different surface areas, and different initial carbon black loadings (35, 50, 70 phr) have been determined. Molecular motion in the rubber phase not in the immediate vicinity of the carbon black surface increases rapidly with increasing solvent concentration, yet it is still slightly restricted compared to rubber with solvent alone. On the other hand, molecular motion in the immobilized layer around carbon black and the fraction rubber in that layer are not affected by the solvent. This indicates strong restriction of molecular motion of polymers at the surface. For estimation of the thickness of the immobilized layer, the necessity of using an appropriate measure of surface area accessible to polymer molecules is pointed out. The degree of immobilization in the layer and the thickness of the layer do not vary appreciably with the nature of carbon black or the initial loading of carbon black.     

Estimation of the Relative Thickness of Gas-Diffusion Electrodes of Carbon-Black Blends in the Course of Electrosynthesis of the Peroxide Ion from Oxygen

The results of a study of electrosynthesis of hydrogen peroxide from oxygen in an alkaline electrolyte on gas-diffusion electrodes of acetylene carbon black and blends of acetylene carbon black and furnace black are compared. The relative thickness of gas-diffusion hydrophobic electrodes operating under inner-kinetic conditions is estimated from polarization curves. Improving the hydrogen peroxide removal from pores of the gas-diffusion electrodes made of carbon black blends with various hydrophilic and hydrophobic properties stabilizes the relative thickness of the electrodes in comparison with the electrodes of acetylene carbon black.     

Carbon black/alumina gel composite: Preparation by sol-gel process in the presence of polymer-grafted carbon black and its electric properties

The preparation of a novel carbon black/alumina gel composite by sol-gel reaction of aluminum isopropoxide (AIP) was investigated. When sol-gel reaction of AIP was carried out in the presence of untreated carbon black, a thin film of alumina gel was hardly obtained, because of the presence of aggregated carbon blacks. On the contrary, in the presence of poly(N-vinyl-2-pyrrolidone)-grafted, poly(2-methyl-2-oxazoline)-grafted, and poly(N,N-diethylacrylamide)-grafted carbon black, a deep-black, thin film of alumina gel, in which carbon blacks were uniformly incorporated, was obtained. Carbon black was incorporated into an alumina gel matrix by the hydrogen bond between carbonyl groups of the grafted polymer and the residual hydroxyl groups in the alumina gel. Electric resistance of the polymer-grafted carbon black/alumina gel composite was very sensitive to the vapor of solvents of the grafted polymer chains on carbon black surface: the electric resistance of the composite drastically decreased in humidity and N,N-dimethylformamide vapor, but not in n-hexane vapor. The logarithm of electric resistance of polymer-grafted carbon black/alumina gel composite linearly decreased in proportion to relative humidity. In addition, the electric resistance of poly(N,N-diethylacrylamide)-grafted carbon black/alumina gel composite under humidity decreased drastically at 32°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3591–3597, 1999     

Influence of conditions for preparation of fullerene-containing carbon black on its microwave properties and yield of fullerenes

Conditions for preparation of the fullerene-containing carbon black with the maximum yield of fullerenes were determined. A correlation between the dielectric constant of the carbon black in the microwave range and the yield of fullerenes was found. The relation of the fullerene-containing carbon black structure to the conditions of its preparation and dielectric constant are discussed.