Combing DNAzyme with single-walled carbon nanotubes for detection of Pb(II) in water

A sensitive and simple assay for the detection of Pb(2+) in aqueous solutions is reported. It takes advantage of the high affinity between single-stranded DNA (ssDNA) and single-walled carbon nanotubes (SWCNT) as well as the capability of SWCNT in fluorescence quenching. Lead(II) catalyzes the cleavage of a fluorescently labeled DNA substrate by a DNAzyme, which releases the single-stranded product to be adsorbed onto a SWCNT. The decrease in fluorescence is proportional to the Pb(2+) concentration. Concentrations as low as 1 nM Pb(2+) in water could be detected and the detection range spans over 5 orders of magnitude. The unique combination of Pb-specific DNAzyme with SWCNT produces a universal, facile and cost-effective sensing platform for lead ions. The concept can be applied to the design of detection assays for other metal ions or small molecules.     

基于核酸切割酶与脱氧核酶的荧光循环放大系统检测铅(Ⅱ)

利用核酸切割酶(Nicking endonuclease)识别特定DNA双链并切割其中某条单链的性质,构建了基于8-17E脱氧核酶(8-17E DNAzyme)的pb2+荧光循环放大检测方法.pb2+可激活8-17E脱氧核酶水解RNA底物,产生并释放出的单链与分子信标探针( Molecular beacon,MB)杂交,导致其茎环结构被破坏,荧光信号恢复;同时形成含有核酸切割酶Nt.BbvCI识别位点的双链区域.在核酸切割酶Nt.BbvCI的作用下,分子信标探针被切割释放,游离出来的单链可与其它分子信标重新杂交,从而触发下一轮酶切,引起荧光检测信号的循环放大.本方法避免了8-17E脱氧核酶与底物链的修饰,最低可以检测出水溶液中1.0×10-10 mol/L Pb2+,并在2倍浓度的Zn2+,以及5倍浓度的其它干扰金属离子存在的情况下对pb2+显示出良好的选择性.本方法对环境水样中pb2+的标准加样回收率为96.1％～108.0％.     

基于脱氧核酶的新型铅离子荧光探针

将荧光猝灭基团修饰的17E脱氧核酶(17E DNAzyme)与荧光基团修饰的底物链通过6个脱氧核苷酸相连, 得到了一种新型的对Pb2+敏感的荧光探针. 由于DNAzyme与底物链发生分子内杂交, 荧光基团与猝灭基团相互靠近, 导致荧光猝灭. 当Pb2+存在时, DNAzyme被激活, 底物链被切断后释放出荧光基团标记的DNA片段, 从而产生明显的荧光信号. 据此可在常温下快速检测Pb2+, 检测下限为10 nmol/L. 在Zn2+, Mn2+, Co2+, Cd2+, Cu2+, Mg2+和Ni2+等多种二价金属离子中, 除Zn2+, Mn2+和Cd2+略有干扰外, 其它几种金属离子均无响应, 表明该荧光探针对Pb2+具有良好的选择性.     

Immobilization of DNAzyme catalytic beacons on PMMA for Pb2+ detection

Due to the numerous toxicological effects of lead, its presence in the environment needs to be effectively monitored. Incorporating a biosensing element within a microfluidic platform enables rapid and reliable determinations of lead at trace levels. A microchip-based lead sensor is described here that employs a lead-specific DNAzyme (also called catalytic DNA or deoxyribozyme) as a recognition element that cleaves its complementary substrate DNA strand only in the presence of cationic lead (Pb(2+)). Fluorescent tags on the DNAzyme translate the cleavage events to measurable, optical signals proportional to Pb(2+) concentration. The DNAzyme responds sensitively and selectively to Pb(2+), and immobilizing DNAzyme in the sensor permits both sensor regeneration and localization of the detection zone. Here, the DNAzyme has been immobilized on a PMMA surface using the highly specific biotin-streptavidin interaction. The strategy includes using streptavidin physisorbed on a PMMA surface to immobilize DNAzyme both on planar PMMA and on the walls of a PMMA microfluidic device. The immobilized DNAzyme retains its Pb(2+) detection activity in the microfluidic device and can be regenerated and reused. The DNAzyme shows no response to other common metal cations and the presence of these contaminants does not interfere with the lead-induced fluorescence signal. While prior work has shown lead-specific catalytic DNA can be used in its solubilized form and while attached to gold substrates to quantitate Pb(2+) in solution, this is the first use of the DNAzyme immobilized within a microfluidic platform for real time Pb(2+) detection.     

Incorporation of a DNAzyme into Au-coated nanocapillary array membranes with an internal standard for Pb(ii) sensing

A Pb(ii)-specific DNAzyme has been successfully incorporated into Au-coated polycarbonate track-etched (PCTE) nanocapillary array membranes (NCAMs) by thiol-gold immobilization. Incorporation of the DNAzyme into the membrane provides a substrate-bound sensor using a novel internal control methodology for fluorescence-based detection of Pb(ii). A non-cleavable substrate strand, identical to the cleavable DNAzyme substrate strand except the RNA-base is replaced by the corresponding DNA-base, is used for ratiometric comparison of intensities. The cleavable substrate strand is labeled with fluorescein, and the non-cleavable strand is labeled with a red fluorophore (Cy5 or Alexa 546) for detection after release from the membrane surface. This internal standard based ratiometric method allows for real-time monitoring of Pb(ii)-induced cleavage, as well as standardizing variations in substrate size, solution detection volume, and monolayer density. The result is a Pb(ii)-sensing structure that can be stored in a prepared state for 30 days, regenerated after reaction, and detect Pb(ii) concentrations as low as 17 nM (3.5 ppb).     

Amplified fluorescence detection of mercury(II) ions (Hg2+) using target-induced DNAzyme cascade with catalytic and molecular beacons

In this work, a fluorescent sensing strategy was developed for the detection of mercury(II) ions (Hg(2+)) in aqueous solution with excellent sensitivity and selectivity using a target-induced DNAzyme cascade with catalytic and molecular beacons (CAMB). In order to construct the biosensor, a Mg(2+)-dependent DNAzyme was elaborately designed and artificially split into two separate oligonucleotide fragments. In the presence of Hg(2+), the specific thymine-Hg(2+)-thymine (T-Hg(2+)-T) interaction induced the two fragments to produce the activated Mg(2+)-dependent DNAzyme, which would hybridize with a hairpin-structured MB substrate to form the CAMB system. Eventually, each target-induced activated DNAzyme could catalyze the cleavage of many MB substrates through true enzymatic multiple turnovers. This would significantly enhance the sensitivity of the Hg(2+) sensing system and push the detection limit down to 0.2 nM within a 20 min assay time, much lower than those of most previously reported fluorescence assays. Owning to the strong coordination of Hg(2+) to the T-T mismatched pairs, this proposed sensing system exhibited excellent selectivity for Hg(2+) detection, even in the presence of 100 times of other interferential metal ions. Furthermore, the applicability of the biosensor for Hg(2+) detection in river water samples was demonstrated with satisfactory results. These advantages endow the sensing strategy with a great potential for the simple, rapid, sensitive, and specific detection of Hg(2+) from a wide range of real samples.     

Target-responsive DNAzyme hydrogel for portable colorimetric detection of lanthanide(Ⅲ) ions

Lanthanide elements(Ln)play an important role in industry and agriculture.As a result of the increasing consumption of lanthanides,environmental emission of Ln has become detrimental to the health of flora and fauna.Current methods for trace lanthanides detection mainly rely on sophisticated instruments.In this article,a Ln~(3+)dependent DNAzyme was incorporated into a hydrogel to generate Ln~(3+)sensitive DNAzyme hydrogel for portable colorimetric detection.The enzyme strand and its substrate strand act as crosslinker and functional unit of the hydrogel with polyacrylamide chains as the scaffold and gold nanoparticles(AuNPs)as the indicator of hydrogel stability.Any ions in the Ln~(3+)series can trigger the cleavage of substrate strand by activating the enzyme strand,thereby decreasing the crosslink ratio and leading to collapse of the hydrogel.The release of the encapsulated AuNPs turns the supernatant wine red.Using this colorimetric method,Ln~(3+)can be detected with high sensitivity,with a limit of detection(LOD)of 20 nM for Ce~(3+).The hydrogel responds specifically to any Ln~(3+)ion and works well with the spiked lake sample without the need of instruments and skilled operators.Our results suggest that the lanthanide responsive hydrogel can be used for portable and sensitive detection of Ln~(3+)contamination in the field.     

DNAzyme-based fluorescent microarray for highly selective and sensitive detection of lead(II)

A facile microarray-based fluorescent sensor for the detection of lead (II) was developed based on the catalytic cleavages of the substrates by a DNAzyme upon its binding to Pb(2+). The release of the fluorophore labelled substrates resulted in the decrease of fluorescence intensity. The sensor had a quantifiable detection range from 1 nM to 1 μM and a selectivity of >20 fold for Pb(2+) over other metal ions.     

A SERS DNAzyme biosensor for lead ion detection

SERS biosensor for sensitive and selective detection of lead ions (Pb(2+)) based on DNAzyme was developed by taking advantage of the specific catalytic reaction of DNAzyme upon binding to Pb(2+) ions. Detection was accomplished by SERS nanoprobe labeled with DNA and Raman reporters for signal amplification.     

Zn(2+)-ligation DNAzyme-driven enzymatic and nonenzymatic cascades for the amplified detection of DNA

A generic fluorescence sensing platform for analyzing DNA by the Zn(2+)-dependent ligation DNAzyme as amplifying biocatalyst is presented. The platform is based on the target DNA induced ligation of two substrate subunits and the subsequent opening of a beacon hairpin probe by the ligated product. The strand displacement of the ligated product by the beacon hairpin is, however, of limited efficiency. Two strategies are implemented to overcome this limitation. By one method, a "helper" nucleic acid sequence is introduced into the system, and this hybridizes with the DNAzyme components and releases the ligated product for opening of the hairpin. By the second method, a nicking enzyme (Nt.BspQI) is added to the system, and this nicks the duplex between the beacon and ligated product while recycling the free ligation product. By combining the two coadded components ("helper" sequence and nicking enzyme), the sensitive detection of the analyte is demonstrated (detection limit, 20 pM). The enzyme-free amplified fluorescence detection of the target DNA is further presented by the Zn(2+)-dependent ligation DNAzyme-driven activation of the Mg(2+)-dependent DNAzyme. According to this method, the Mg(2+)-dependent DNAzyme subunits displace the ligated product, and the resulting assembled DNAzyme cleaves a fluorophore/quencher-modified substrate to yield fluorescence. The method enabled the detection of the target DNA with a detection limit corresponding to 10 pM. The different sensing platforms are implemented to detect the Tay-Sachs genetic disorder mutant.     

Metal-dependent global folding and activity of the 8-17 DNAzyme studied by fluorescence resonance energy transfer

The 8-17 DNAzyme is a DNA metalloenzyme catalyzing RNA transesterification in the presence of divalent metal ions, with activity following the order Pb2+ > Zn2+ >Mg2+. Since the DNAzyme has been used as a metal ion sensor, its metal-induced global folding was studied by fluorescence resonance energy transfer (FRET) by labeling the three stems of the DNAzyme with the Cy3/Cy5 FRET pair two stems at a time in order to gain deeper insight into the role of different metal ions in its structure and function. FRET results indicated that, in the presence of Zn2+ and Mg2+, the DNAzyme folds into a compact structure, stem III approaching a configuration defined by stems I and II without changing the angle between stems I and II. Correlations between metal-induced folding and activity were also studied. For Zn2+ and Mg2+, the metal ion with higher affinity for the DNAzyme in global folding (Kd(Zn) = 52.6 microM and Kd(Mg) = 1.36 mM) also displays higher affinity in activity (Kd(Zn) = 1.15 mM and Kd(Mg) = 53 mM) under the same conditions. Global folding was saturated at much lower concentrations of Zn2+ and Mg2+ than the cleavage activities, indicating the global folding of the DNAzyme occurs before the cleavage activity for those metal ions. Surprisingly, no Pb2+-dependent global folding was observed. These results suggest that for Pb2+ global folding of the DNAzyme may not be a necessary step in its function, which may contribute to the DNAzyme having the highest activity in the presence of Pb2+.     

Accelerated color change of gold nanoparticles assembled by DNAzymes for simple and fast colorimetric Pb2+ detection

The combination of high metal selectivity of DNAzymes with the strong distance-dependent optical properties of metallic nanoparticles has presented considerable opportunities for designing colorimetric sensors for metal ions. We previously communicated a design for a colorimetric lead sensor based on the assembly of gold nanoparticles by a Pb(2+)-dependent DNAzyme. However, heating to 50 degrees C followed by a cooling process of approximately 2 h was required to observe the color change. Herein we report a new improved design that allows fast (<10 min) detection of Pb(2+) at ambient temperature. This improvement of sensor performance is a result of detailed studies of the DNAzyme and nanoparticles, which identified "tail-to-tail" nanoparticle alignment, and large (42 nm diameter) nanoparticle size as the major determining factors in allowing fast color changes. The optimal conditions for other factors such as temperature (35 degrees C) and concentrations of the DNAzyme (2 microM), its substrate (3 nM), and NaCl (300 mM) have also been determined. These results demonstrate that fundamental understanding of the DNAzyme biochemistry and nanoparticle science can lead to dramatically improved colorimetric sensors.     

DNAzyme based electrochemical sensors for trace uranium

We have developed a uranyl-specific DNAzyme that was immobilized on the surface of a gold electrode to give a highly sensitive and selective biosensor for uranyl ion. The typical DNAzyme system consisted of the RNA (rA) as the substrate (ADNA), and the other strand is the enzyme (TDNA) with a ferrocene (Fc). The presence of uranyl ion induces the cleavage of the DNA substrate strand at the rA position to form two fragments. The Fc unit thereby is released from the surface of the electrode, and this results in a decreased peak current. This electrochemical biosensor has a dynamic range from 2 nM to 14 nM of uranyl ion, with a detection limit at 1 nM. It exhibits high sensitivity and excellent selectivity over other metal ions, and thus represents a promising technique for simple, fast, on-site, and real-time electrochemical sensing of UO₂(II) ion. It also serves as a guide in choosing different methods for designing electrochemical sensors for other metal ions.

A thin-layer chromatography plate prepared from BODIPY-based receptor immobilized SiO2 nanoparticles as a portable chemosensor for Pb2+

A new fluorescence receptor based on BODIPY-immobilized silica nanoparticles (BODIPY-SiO(2)) exhibits a high affinity and selectivity for Pb(2+) over competing metal ions in water. An overall emission change of ca. 100-fold at the emission maximum was observed for Pb(2+). The fluorescence receptor BODIPY-SiO(2) can remove 97% and 95% of the initial 100 ppb Pb(2+) from human blood and waste solution, respectively. Experiments show the fluorescence receptor BODIPY-SiO(2) can be a potentially useful and effective agent for the selective separation and rapid removal of Pb(2+)in vivo. We also prepared a portable chemosensor kit by coating a 4 μm thick film of BODIPY-SiO(2) onto a glass substrate. We found that this BODIPY-SiO(2) film detects Pb(2+) ions at pH 7.4 with a sensitivity of 3.2 nM. Finally, we tested the effect of pH on BODIPY-SiO(2) with Pb(2+) ions between pH 3.0 and 11.0. The fluorescence changes of BODIPY-SiO(2) were almost constant between pH 3 and 11. The results imply that the BODIPY-SiO(2) film is applicable as a portable chemosensor for detection of Pb(2+) ions in the environmental field.     

核酸荧光探针检测铅离子的研究

将8-17 DNAzym e增加2个"G-C"碱基对进行增强热稳定性的结构修饰,并标记上1个荧光基团"FAM"和2个荧光猝灭基团"Dabcyl",设计成双猝灭Pb2+荧光探针。研究了该探针对Cd2+、Zn2+、Mg2+、Cu2+、Mn2+、Pb2+6种二价金属离子的响应,结果表明探针对Pb2+具有很强的特异性,在探针浓度为2.5×10-7mol/L时,Pb2+浓度在8.5×10-8~7.5×10-6mol/L范围内和探针的荧光强度呈线性关系,检出限为8.5×10-8mol/L。该探针可用于Pb2+的定性和定量检测。     

Probing metal binding in the 8-17 DNAzyme by TbIII luminescence spectroscopy

Metal-dependent cleavage activities of the 8-17 DNAzyme were found to be inhibited by Tb(III) ions, and the apparent inhibition constant in the presence of 100 microM of Zn(II) was measured to be 3.3+/-0.3 microM. The apparent inhibition constants increased linearly with increasing Zn(II) concentration, and the inhibition effect could be fully rescued with addition of active metal ions, indicating that Tb(III) is a competitive inhibitor and that the effect is completely reversible. The sensitized Tb(III) luminescence at 543 nm was dramatically enhanced when Tb(III) was added to the DNAzyme-substrate complex. With an inactive DNAzyme in which the GT wobble pair was replaced with a GC Watson-Crick base pair, the luminescence enhancement was slightly decreased. In addition, when the DNAzyme strand was replaced with a complete complementary strand to the substrate, no significant luminescence enhancement was observed. These observations suggest that Tb(III) may bind to an unpaired region of the DNAzyme, with the GT wobble pair playing a role. Luminescence lifetime measurements in D(2)O and H(2)O suggested that Tb(III) bound to DNAzyme is coordinated by 6.7+/-0.2 water molecules and two or three functional groups from the DNAzyme. Divalent metal ions competed for the Tb(III) binding site(s) in the order Co(II)>Zn(II)>Mn(II)>Pb(II)>Ca(II) approximately Mg(II). This order closely follows the order of DNAzyme activity, with the exception of Pb(II). These results indicate that Pb(II), the most active metal ion, competes for Tb(III) binding differently from other metal ions such as Zn(II), suggesting that Pb(II) may bind to a different site from that for the other metal ions including Zn(II) and Tb(III).     

Label-free fluorescent detection of thrombin using G-quadruplex-based DNAzyme as sensing platform

We report herein a label-free and sensitive fluorescent method for detection of thrombin using a G-quadruplex-based DNAzyme as the sensing platform. The thrombin-binding aptamer (TBA) is able to bind hemin to form the G-quadruplex-based DNAzyme, and thrombin can significantly enhance the activity of the G-quadruplex-based DNAzyme. The G-quadruplex-based DNAzyme is found to effectively catalyze the H(2)O(2)-mediated oxidation of thiamine, giving rise to fluorescence emission. This allows us to utilize the H(2)O(2)-thiamine fluorescent system for the quantitative analysis of thrombin. The assay shows a linear toward thrombin concentration in the range of 0.01-0.12 nM. The present limit of detection for thrombin is 1 pM, and the sensitivity for analyzing thrombin is improved by about 10,000-fold as compared with the reported colorimetric counterpart. The work also demonstrates that thiamine is an excellent substrate for the fluorescence assay using the G-quadruplex-based DNAzyme as the sensing platform.     

Gold nanorods-based FRET assay for ultrasensitive detection of Hg2+

A fluorescence method for detecting mercury ion in a homogeneous medium is proposed with gold nanorods (GNRs) as a fluorescence quencher on the basis of the fluorescence resonance energy transfer (FRET). Under the optimum conditions, the method exhibits a dynamic response range from 10 pM to 5 nM with a detection limit of 2.4 pM.     

DNAzyme crosslinked hydrogel: a new platform for visual detection of metal ions

We propose the use of DNAzyme as a crosslinker of hydrogel to develop a catalytic platform for the sensing of metal ions. The DNAzyme crosslinked hydrogel can undergo gel-sol transition in response to Cu(2+) ions, which enables sensitive visual detection of Cu(2+) by observing the release of pre-trapped AuNPs.     

Target-responsive DNAzyme hydrogel for portable colorimetric detection of lanthanide(III) ions

Lanthanide elements (Ln) play an important role in industry and agriculture. As a result of the increasing consumption of lanthanides, environmental emission of Ln has become detrimental to the health of flora and fauna. Current methods for trace lanthanides detection mainly rely on sophisticated instruments. In this article, a Ln³⁺ dependent DNAzyme was incorporated into a hydrogel to generate Ln³⁺ sensitive DNAzyme hydrogel for portable colorimetric detection. The enzyme strand and its substrate strand act as crosslinker and functional unit of the hydrogel with polyacrylamide chains as the scaffold and gold nanoparticles (AuNPs) as the indicator of hydrogel stability. Any ions in the Ln³⁺ series can trigger the cleavage of substrate strand by activating the enzyme strand, thereby decreasing the crosslink ratio and leading to collapse of the hydrogel. The release of the encapsulated AuNPs turns the supernatant wine red. Using this colorimetric method, Ln³⁺ can be detected with high sensitivity, with a limit of detection (LOD) of 20 nM for Ce³⁺. The hydrogel responds specifically to any Ln³⁺ ion and works well with the spiked lake sample without the need of instruments and skilled operators. Our results suggest that the lanthanide responsive hydrogel can be used for portable and sensitive detection of Ln³⁺ contamination in the field.