二醋酸纤维素和聚己内酯单丙烯酸酯接枝共聚物的生物降解性能研究

通过在土壤和活性淤泥中进行生物降解的研究结果表明,二醋酸纤维素(CDA)和聚己内酯单丙烯酸酯(PCLA)的接枝共聚物(CDA-g-PCLA)在活性淤泥中的降解失重率要略高于在土壤中的降解失重率。CDA-g-PCLA的特性粘数在降解初期呈上升趋势,30 d左右达到峰值后呈下降趋势。CDA-g-PCLA和CDA随降解时间的延长,拉伸强度下降,断裂伸长率增大。     

Mechanical Properties of Regenerated Cellulose Fibres for Composites

Summary: A broad variety of regenerated cellulose fibres was subjected to single fibre tensile tests in order to determine the modulus of elasticity, tensile strength, and failure strain. The results were compared to glass fibres and flax fibres, which are considered the most important technical and natural fibres, respectively. With regard to their modulus of elasticity and tensile strength, regenerated cellulose fibres showed clearly lower values than glass fibres, even when their low density was taken into account. The average modulus of elasticity and tensile strength of regenerated cellulose fibres was also lower than the values measured for flax fibres, but when variability was considered, both fibres performed similarly. In terms of interfacial shear strength with polypropylene, lyocell fibres performed significantly less well than sized glass fibre and ramie fibre. The most important difference between regenerated cellulose fibres and both glass and flax fibres is their high failure strain and thus high work to fracture. The high work to fracture of regenerated cellulose fibres makes them particularly useful for composite applications where high fracture toughness is required.     

Some Properties of Polyelectrolyte-G rafted Cellulose

Anionic and cationic polyelectrolytes were grafted on a bleached kraft pulp. Grafting an anionic polyelectrolyte (sodium poly-acrylate-polyacrylamide copolymer) resulted in modified fibers possessing outstanding affinity for water and saline solutions in the pH range where the polymer is ionized. Swelling is the result of both the grafting operation itself and of the presence of the ionized polyelectrolyte.

The swollen grafted fibers could be disintegrated under intense shear to give a colloidal solution exhibiting pseudoplastic thixo-tropic behavior. Electron microscopic examination revealed that during the shearing process the fiber had been disintegrated into its constitutive elements, long rodlike protofibrils, which are believed to be mainly responsible for the high viscosities observed.

Grafting a cationic polyelectrolyte (polydimethylamino ethyl methacrylate hydrochloride) produced fibers with lower but significant water swelling. The influence of pH on swelling was similar, although reversed, to that observed with the anionic grafted fibers. The presence of a large number of cationic groups in the porous cellulose fiber gel points to applications in ion-exchange and adsorption processes.     

二醋酸纤维素接枝聚己内酯的核磁共振表征

用^1H-NMR和^13C-NMR研究了二醋酸纤维素(CDA)和聚己内酯(PCL)的接枝共聚反应,确定了^1H-NMR和^13C-NMR谱中各谱峰的归属,为证明二醋酸纤维素和己内酯的接枝共聚反应提供了依据。     

Preparation and Characterization of Nanocomposites of Carboxymethyl Cellulose Reinforced with Cellulose Nanocrystals

Summary: Cellulose nanocrystals (CNC) were extracted from Kraft pulp of Eucalyptus urograndis. The CNC were isolated by acid hydrolysis with H₂SO₄ 64% (w/w) solution, for 20 minutes at 45 °C. The morphology and crystallinity of the CNC were investigated by atomic force microscopy (AFM) and X-ray diffraction (XRD), respectively. The AFM image supports the evidence for the development of crystals of cellulose in nanometric scale. These nanoparticles were used as reinforcement material in carboxymethyl cellulose (CMC) matrix. Nanocomposites films were prepared by casting. The nanocomposites were characterized by thermal (TGA) and mechanical (DMA) analyses. A large reinforcing effect of the filler was observed. The tensile strength of nanocomposites was significantly improved by 107%, the elongation at break decreased by 48% and the thermal resistance increased slightly. The improvements in thermo-mechanical properties suggest a close association between filler and matrix.     

Reinforcing Poly(ethylene) with Cellulose Nanocrystals

The fabrication of nanocomposites of low‐density polyethylene (LDPE), one of the world's most widely used polymers, and cellulose nanocrystals (CNCs), which represent the world's most abundant bio‐based nanofiller, is reported. While the hydrophobic polymer and the hydrophilic filler seem to be intrinsically incompatible, this article shows that it is possible to kinetically trap homogeneous nanocomposites by a templating approach. An organogel is first prepared by exchanging the solvent of an aqueous CNC dispersion against acetone, impregnating the resulting organogel, in which the CNCs form a percolating network with a hot LDPE solution in toluene, and compression‐molding the resulting materials into thin films. At a filler content of 7.6% v/v, the resulting materials display a three‐ to four‐fold increase in strength and stiffness compared with the neat LDPE, which confirms that the CNC network could be largely maintained. It is also possible to reprocess these nanocomposites and dilute them with LDPE using conventional melt‐processing techniques.

     

Influence of Interfacial Enantiomeric Grafting on Melt Rheology and Crystallization of Polylactide/Cellulose Nanocrystals Composites

Incorporating the surface-grafted cellulose nanocrystals(CNCs)with enantiomeric polylactide(PLLA or PDLA)is an effective and sustainable way to modify PLLA,but their difference in promoting matrix crystallization is still unrevealed.In this study,the CNCs with identical content and length of PLLA and PDLA(CNC-g-L and CNC-g-D)were prepared and blended with PLLA.The rheological properties of PLLA/CNC-gD are greatly improved,indicating that the stereocomplexation can significantly improve the interfacial strength as compared with the conventional van der Waals force in PLLA/CNC-g-L.Surprisingly,the matrix crystallizes at a higher rate in PLLA/CNC-g-L than PLLA/CNC-g-D.PLLA/CNC-g-L15 reaches its half crystallinity in 8.26 min while a longer period of 13.41 min is required for PLLA/CNC-g-D15.POM observation reveals that the superior crystallization behavior in PLLA/CNC-g-L is originated from its higher nucleation efficiency and faster growth rate.The formation of low content of sc-PLA at the interface can restrict the diffusion of PLLA but contribute less to generate crystalline nuclei,which synergistically leads to the retarded crystallization kinetics in PLLA/CNC-g-D.Revealing the mechanism of different interfacial enantiomeric grafting on the melt rheology and crystallization of PLLA is of great significance for the development of high-performance polylactide materials.     

CdSe纳米晶/共轭聚合物太阳电池的制备与性能研究

采用有机金属液相法制备了平均粒径为5 nm的CdSe纳米微球(ns-CdSe), 并将其与共轭聚合物(MEH-PPV或P3HT)共混制备了太阳电池器件. 透射电镜(TEM)、紫外-可见吸收光谱(UV-Vis)及荧光光谱(PL)研究结果表明, CdSe纳米晶呈均匀的球状颗粒, 在近红外区具有良好的吸收和荧光性能; 加入CdSe纳米晶能够有效地淬灭共轭聚合物的荧光. 在AM1.5模拟太阳光(光强为100 mW/cm2)照射下, ns-CdSe/MEH-PPV共混体系太阳电池器件性能测试结果为: 短路电流ISC为1.56 mA/cm2, 开路电压VOC为0.75 V, 填充因子FF为34.5％, 光电转换效率η为0.40%; 对于ns-CdSe/P3HT共混体系, 其ISC为1.93 mA/cm2, VOC为0.65 V, FF为38.4%, η为0.48%.     

纤维素纳米晶模板法制备多级孔炭材料及其电化学性能

以纤维素纳米晶(CNC)为模板,酚醛树脂为碳源,KOH为活化剂,通过高温碳化制备了多级孔炭材料.采用透射电子显微镜(TEM)、扫描电子显微镜(SEM)和X射线光电子能谱仪(XPS)等手段对合成的一系列炭材料进行了表征.结果表明,前驱体中CNC的降解会形成与CNC直径相当的介孔,KOH活化则会导致炭材料产生大量的微孔和大孔,以及部分4 nm左右较小尺度的介孔,所制备炭材料呈现明显的多级孔特性,其比表面积达554.7 m²/g,总孔体积为0.323 cm³/g.以CNC为模板,KOH活化的炭材料作为电极材料时,在1.0 A/g电流密度下其比电容达202.8 F/g,当电流密度升高至40.0 A/g时,其电容保持率仍达69%,表明该炭材料具有优异的倍率性能;由该电极材料组装的超级电容器在10000次充放电循环后,电容保持率达95%以上,具有良好的循环稳定性.     

Carbonization of Polyacrylonitrile Composites with Nitrogen-containing Cellulose Derivatives

Thermal carbonization of nitrogen-containing cellulose derivatives (chitin, chitosan, cyanoethyl chitosan, cyanoethyl cellulose, copolymers of allyl carboxymethyl cellulose with polyacrylonitrile) as models of probable products of thermal reaction of cellulose with polyacrylonitrile was studied. The quantitative characteristics of carbonization of the model compounds are influenced by the nitrile group.     

聚己内酯分子量对乙基纤维素/聚己内酯共混体系的溶致性液晶织构的影响

利用偏光显微镜研究了乙基纤维素与聚己内酯共混物在二氯乙酸中的溶致性液晶形态。结果表明聚己内酯的分子量对共混体系的溶致性液晶结构有明显的影响。差示扫描量法测试显示含不同分子量聚己内酯的共混物,其混溶性及两组分间的相互作用无十分明显的差异。聚内酯分子量对共混体系溶致性液晶的形态和热稳定性的影响,可认为是由于分子量对体系的粘度贡献引起的。     

Supercritical Carbon Dioxide Isolation of Cellulose Nanofibre and Enhancement Properties in Biopolymer Composites

The physical properties, such as the fibre dimension and crystallinity, of cellulose nanofibre (CNF) are significant to its functional reinforcement ability in composites. This study used supercritical carbon dioxide as a fibre bundle defibrillation pretreatment for the isolation of CNF from bamboo, in order to enhance its physical properties. The isolated CNF was characterised through zeta potential, TEM, XRD, and FT-IR analysis. Commercial CNF was used as a reference to evaluate the effectiveness of the method. The physical, mechanical, thermal, and wettability properties of the bamboo and commercial CNF-reinforced PLA/chitin were also analysed. The TEM and FT-IR results showed the successful isolation of CNF from bamboo using this method, with good colloidal stability shown by the zeta potential results. The properties of the isolated bamboo CNF were similar to the commercial type. However, the fibre diameter distribution and the crystallinity index significantly differed between the bamboo and the commercial CNF. The bamboo CNF had a smaller fibre size and a higher crystallinity index than the commercial CNF. The results from the CNF-reinforced biocomposite showed that the physical, mechanical, thermal, and wettability properties were significantly different due to the variations in their fibre sizes and crystallinity indices. The properties of bamboo CNF biocomposites were significantly better than those of commercial CNF biocomposites. This indicates that the physical properties (fibre size and crystallinity) of an isolated CNF significantly affect its reinforcement ability in biocomposites. The physical properties of isolated CNFs are partly dependent on their source and production method, among other factors. These composites can be used for various industrial applications, including packaging.     

Thermal Degradation of Cellulose Nanocrystals Deposited on Different Surfaces

Thermal degradation of cellulose nanocrystals deposited on flat solid surfaces was monitored by AFM coupled with analysis of obtained images using image processor. The nanocrystals deposited on TiO₂ substrate showed different degradation patterns compared to those deposited on the nanosized layer of amorphous cellulose. The degradation was complete within 20 minutes at 300 °C. The nanocrystal deposited on amorphous cellulose resisted the heat treatment up to 120 minutes. Visual comparison and analysis of the AFM images clearly demonstrated the impact of temperature on the degradation rate of the nanocrystals deposited on TiO₂ substrate.     

Effect of Process Conditions and Colloidal Properties of Cellulose Nanocrystals Suspensions on the Production of Hydrogel Beads

The influence of the physical, rheological, and process parameters on the cellulose nanocrystal (CNC) drops before and after external gelation in a CaCl₂ solution was investigated. The dominant role of the CNC’s colloidal suspension properties, such as the viscous force, inertial, and surface tension forces in the fluid dynamics was quantitatively evaluated in the formation of drops and jellified beads. The similarity and difference between the behavior of carbohydrate polymers and rod-like crystallites such as CNC were enlightened. Pump-driven and centrifugally-driven external gelation approaches were followed to obtain CNC hydrogel beads with tunable size and regular shape. A superior morphological control—that is, a more regular shape and smaller dimension of the beads—were obtained by centrifugal force-driven gelation. These results suggest that even by using a simple set-up and a low-speed centrifuge device, the extrusion of a colloidal solution through a small nozzle under a centrifugal field is an efficient approach for the production of CNC hydrogel beads with good reproducibility, control over the bead morphology and size monodispersion.     

Reductive Amination Reaction for the Functionalization of Cellulose Nanocrystals

Cellulose nanocrystals (CNCs) represent intriguing biopolymeric nanocrystalline materials, that are biocompatible, sustainable and renewable, can be chemically functionalized and are endowed with exceptional mechanical properties. Recently, studies have been performed to prepare CNCs with extraordinary photophysical properties, also by means of their functionalization with organic light-emitting fluorophores. In this paper, we used the reductive amination reaction to chemically bind 4-(1-pyrenyl)butanamine selectively to the reducing termini of sulfated or neutral CNCs (S_CNC and N_CNC) obtained from sulfuric acid or hydrochloric acid hydrolysis. The functionalization reaction is simple and straightforward, and it induces the appearance of the typical pyrene emission profile in the functionalized materials. After a characterization of the new materials performed by ATR-FTIR and fluorescence spectroscopies, we demonstrate luminescence quenching of the decorated N_CNC by copper (II) sulfate, hypothesizing for these new functionalized materials an application in water purification technologies.     

Polymer and Mesoporous Silica Microspheres with Chiral Nematic Order from Cellulose Nanocrystals

Polymer microspheres with chiral nematic order were obtained from an emulsion polymerization technique using cellulose nanocrystals (CNCs) as the template. The growth of the liquid crystals from tiny tactoids to droplets with spherical symmetry was captured and investigated by both optical and electron microscopy for the first time. The size of the microspheres could be tuned between tens and hundreds of micrometers; to obtain single, integrated chiral nematic kernels, the size of water droplets in the emulsion should be similar to that of CNC tactoids. Through a double‐matrix templating method, novel silica microspheres with chiral nematic order were fabricated, which showed a high surface area and mesoporosity. The methods developed here may help to reveal the evolution of other self‐assembling systems, and these materials have potential applications in optical devices and chiral separations.     

Study of the Structure and Sorption Properties of Some Types of Cellulose

The pulsed NMR, isopiestic and pycnometric methods are applied to investigate the physicochemical properties of softwood [GOST (State Standard) 9571-89] and hardwood [GOST 28172-89] celluloses, as well as flax cellulose [GOST 10330-76, 9394-76], both in the initial state and subjected to chemical treatment. Possible changes occurring in the supramolecular structure of a polymer are analyzed. The structural and sorption characteristics of the investigated samples are calculated. Their water absorption capacities are determined.     

Tailoring the Chemical Structure of Cellulose Nanocrystals by Amine Functionalization

The surface functionalization of cellulose nanocrystals is presently considered a useful and straightforward tool for accessing very reliable biocompatible and biodegradable nanostructures with tailored physical and chemical properties. However, to date the fine characterization of the chemical appendages introduced onto cellulose nanocrystals remains a challenge, due to the low sensitivity displayed by the most common techniques towards surface functionalization. In this paper, we demonstrate the easy functionalization of cellulose nanocrystals with aliphatic and aromatic amines, demonstrating the tunability of their properties in dependence on the selected functionality. Then, we apply to colloidal suspensions of modified nanocrystals ¹H NMR analysis to elucidate their surface structure. To the best of our knowledge, this is the first report where such investigation was performed on cellulose nanocrystals presenting both surface and reducing end modification. These results involve interesting implications for the fields of cultural heritage and of materials chemistry.     

Preparation of Cellulose Nanocrystals from Jujube Cores by Fractional Purification

Jujube cores are fiber-rich industrial waste. Dewaxing, alkali treatment, bleaching, and sulfuric acid hydrolysis were used to generate cellulose nanocrystals (CNCs) from the jujube cores in this study. The morphological, structural, crystallinity, and thermal properties of the fibers were investigated using FE-SEM, TEM, AFM, FT-IR, XRD, and TGA under various processes. CNCs’ zeta (ζ) potential and water contact angle (WAC) were also investigated. The findings demonstrate that non-fibrous components were effectively removed, and the fiber particles shrunk over time because of many activities. CNCs had a rod-like shape, with a length of 205.7 ± 52.4 nm and a 20.5 aspect ratio. The crystal structure of cellulose Iβ was preserved by the CNCs, and the crystallinity was 72.36%. The temperature of the fibers’ thermal degradation lowered during the operations, although CNCs still had outstanding thermal stability (>200 °C). Aside from the CNCs, the aqueous suspension of CNCs was slightly agglomerated; thus, the zeta (ζ) potential of the CNCs’ suspension was −23.72 ± 1.7 mV, and the powder had high hydrophilicity. This research will be valuable to individuals who want to explore the possibility for CNCs made of jujube cores.