Selective solid‐phase extraction using a molecularly imprinted polymer for the analysis of patulin in apple‐based foods

The aim of this work was to evaluate the use of a molecularly imprinted polymer as a selective solid‐phase extraction sorbent for the clean‐up and pre‐concentration of patulin from apple‐based food products. Ultra high pressure liquid chromatography coupled to ultraviolet absorbance detection was used for the analysis of patulin. The molecularly imprinted polymer was applied, for the first time, to the determination of patulin in apple juice, puree and jam samples spiked within the maximum levels specified by the European Commission No. 1881/2006. High recoveries (>77%) were obtained. The method was validated and found to be linear in the range 2–100 μg/kg with correlation coefficients greater than 0.965 and repeatability relative standard deviation below 11% in all cases. Compared with dispersive solid‐phase extraction (QuEChERS method) and octadecyl sorbent, the molecularly imprinted polymer showed higher recoveries and selectivity for patulin. The application of Affinisep molecularly imprinted polymer as a selective sorbent material for detection of patulin fulfilled the method performance criteria required by the Commission Regulation No. 401/2006, demonstrating the suitability of the technique for the control of patulin at low ppb levels in different apple‐based foods such as juice, puree and jam samples.     

Development of Electrochemical Platform Based on Molecularly Imprinted Poly(methacrylic acid) Grafted on Iniferter-modified Carbon Nanotubes for 17β-Estradiol Determination in Water Samples

This paper describes the development of a new electrochemical sensor for 17β-estradiol (E2) determination based on glassy carbon electrode (GCE) modified with molecularly imprinted polymer grafted onto iniferter-multiwall carbon nanotubes surface (MIP-MWCNT) and dihexadecyl-hydrogen-phosphate (DHP). The electrochemical method was based on closed-circuit preconcentration of E2 in 0.1 mol L⁻¹ phosphate buffer (pH 7.0) during 500 s. Upon preconcentration, E2 was determined by differential pulse voltammetry (DPV) exhibiting a limit of detection of 0.01 μmol L⁻¹. The sensor exhibited higher selectivity toward E2 and it was applied for E2 determination in natural water samples, with accuracy attested by HPLC-DAD.     

Evaluation of a molecularly imprinted polymer for the isolation/enrichment of β-estradiol

The selective preconcentration of estradiol was explored using the recognition ability of a molecularly imprinted polymer (MIP) in the solid phase extraction (SPE) format. Polymeric particles were imprinted with 17β-estradiol using methacrylic acid as functional monomer and divinylbenzene as crosslinker. Binding studies of these polymeric particles towards 17β-estradiol showed selectivity over non-imprinted polymers, using acetonitrile as solvent. The imprinted polymer showed a recovery of 88% for β-estradiol in deionized water and 81% in surface water. The selectivity of the MIP over the non-imprinted polymer was relatively low, only 10% higher recovery. The results indicate that the MIP imprinted with 17β-estradiol does not appear to provide a viable approach to be used in a sample clean-up or enrichment step for the determination of estradiol in aqueous systems.     

Tailor‐made ion‐imprinted polymer based on functionalized graphene oxide for the preconcentration and determination of trace copper in food samples

A tailor‐made Cu(II) ion‐imprinted polymer based on large‐surface‐area graphene oxide sheets has been synthesized for the preconcentration and determination of trace copper from food samples by solid‐phase extraction. Attributed to the ultrahigh surface area and hydrophilicity of graphene oxide, the Cu(II) ion‐imprinted polymer prepared by the surface ion‐imprinting technique exhibited a high binding capacity and a fast adsorption rate under the optimized experimental conditions. In the static adsorption experiments, the maximum adsorption capacity of Cu(II) ion‐imprinted polymer is 109.38 mg/g at 25°C, which is much higher than that of the nonimprinted polymer (32.12 mg/g). Meanwhile, the adsorption is very rapid and equilibrium is reached after approximately 30 min. The adsorption mechanism is found to follow Langmuir adsorption model and the pseudo‐second‐order adsorption process. The Cu(II) ion‐imprinted polymer was used for extracting and detecting Cu(II) in food samples combined with graphite flame atomic adsorption spectrometry with high recoveries in the range of 97.6–103.3%. The relative standard deviation and limit of detection of the method were evaluated as 1.2% and 0.37 μg/L, respectively. The results showed that the novel absorbent can be utilized as an effective material for the selective enrichment and determination of Cu(II) from food samples.     

Sensitive and Selective Voltammetric Determination of Ciprofloxacin Using Screen-printed Electrodes Modified with Carbon Black and Magnetic-molecularly Imprinted Polymer

This work reports the construction of screen-printed electrode (SPE) modified with carbon black (CB) and magnetic Fe₃O₄ nanoparticles coated with molecularly imprinted polymer (mag@MIP) based on an alternative low-cost approach. The proposed device was used for the sensitive and selective voltammetric determination of the antibiotic ciprofloxacin. The results obtained from cyclic voltammetry pointed to the improvement of the SPE response toward the irreversible oxidation of ciprofloxacin after the modification of the electrode surface with CB-based film and the magnetic preconcentration of mag@MIP containing adsorbed ciprofloxacin molecules. Compared to the non-molecularly imprinted sensor (mag@NIP), the presence of cavities selective for ciprofloxacin recognition in the mag@MIP nanoparticles accounted for the improvement in analytical signal of the molecularly imprinted sensor. The application of differential pulse voltammetry for ciprofloxacin determination yielded a linear response in the concentration range of 0.5 to 7.0 μmol L⁻¹. The repeatability and interference tests results showed that the proposed electrochemical sensor has good measurement accuracy and selectivity. The proposed device was applied for the voltammetric determination of ciprofloxacin in river water and synthetic urine samples, where recovery rates close to 100 % were recorded for all the samples. The quantification data obtained from the application of the proposed voltammetric method were quite consistent with those of the HPLC reference method.     

Continuous solid-phase extraction and preconcentration of bisphenol A in aqueous samples using molecularly imprinted columns

A bisphenol A (BPA) molecularly imprinted polymer, the composition of which was optimised using a chemometric approach, has been applied to the selective preconcentration of the template from aqueous samples. The selectivity of the polymer toward BPA and related compounds was evaluated chromatographically. The BPA-imprinted polymer was packed in a column and used for continuous on-column solid-phase extraction (MISPE) of aqueous samples followed by subsequent analysis by HPLC with fluorescence detection of the eluted fractions. The composition of the washing solvent applied in the MISPE procedure was optimised to favour the specific interactions of the MIP with BPA and to remove the non-selectively bound matrix components. The MISPE method has proven to be effective for selective preconcentration of BPA in aqueous samples (recoveries >84% obtained in the eluate for 10–100 mL sample volumes) enabling detection and quantification limits of 1.0 and 3.3 ng mL^–1, respectively (based on 25 mL sample size). Analytical recoveries were between 92 and 101% for river water samples spiked with known amounts of BPA (30, 60, and 80 ng mL^–1); relative standard deviations (RSD) were lower than 5.0%.     

Speciation,adsorption and determination of chromium(III) and chromium(VI) on a mesoporous surface imprinted polymer adsorbent by combining inductively coupled plasma atomic emission spectrometry and UV spectrophotometry

In the present study, a Cr(III)‐imprinted polymer (Cr(III)‐IIP) was prepared by an easy one‐step sol–gel reaction with a surface imprinting technique on the support of silica mesoporous material. A new SPE method for the speciation, separation, preconcentration, and determination of Cr(III) and Cr(VI) by inductively coupled plasma atomic emission spectrometry and UV on the mesoporous‐imprinted polymer adsorbent was developed. The structure of the imprinted polymer was characterized by Fourier transform infrared spectroscopy, X‐ray powder diffraction, transmission electron microscopy, and nitrogen adsorption–desorption isotherms. The adsorption kinetics, thermodynamics behavior, and recognition ability toward Cr(III) on Cr(III)‐IIP and nonimprinted polymer were compared. The results showed that Cr(III)‐IIP had higher selectivity and nearly a two times larger Langmuir adsorption capacity (38.50 mg/g) than that of NIP. The proposed method has been successfully applied in the determination and speciation of chromium in natural water samples with satisfactory results.     

Development of carbon paste electrode modified with cadmium ion-imprinted polymer for selective voltammetric determination of Cd2+

A simple and fast voltammetric method based on a new electrode composed of carbon paste electrode/bifunctional hybrid ion imprinted polymer (CPE/IIP) was developed for the quantification of Cd²⁺ in water samples. The voltammetric measurements by Differential Pulse Voltammetry were performed by using CPE containing 11.0 mg of IIP under phosphate buffer solution at concentration 0.1 mol L^?1 and pH 6.5. The electrochemical method was carried out by Cd²⁺ preconcentration at ?1.2 V during 210 s, followed by anodic stripping. The performance of IIP towards Cd²⁺ determination was evaluated by comparison to non-imprinted polymer, whose detectability of IIP was much higher (45%). The sensitivity of the sensor was found to be 0.0105 µA/µg L^?1. The limits of detection and limits of quantification were found to be 4.95 μg L^?1 and 16.4 μg L^?1, respectively. The developed method was successfully applied to Cd²⁺ determination in mineral, tap and lake water samples, whose results are in agreement with thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) used as reference analytical technique. According to achieved results, the developed method can be used for routine analysis of quality control of water samples from different sources.     

Preparation and evaluation of molecularly imprinted ionic liquids polymer as sorbent for on-line solid-phase extraction of chlorsulfuron in environmental water samples

In this report, vinylimidazolium ionic liquid as a functional monomer for preparation of chlorsulfuron (CS) imprinted polymers were first studied. The imprinted materials showed high selectivity for CS, and fast kinetics so that adsorption equilibrium was achieved within 5 min. These materials have been further employed to detect trace CS from water samples by online preconcentration coupled with HPLC. The sorbent offered good linearity (0.005-30 μg L(-1), r(2)>0.99) for on-line solid-phase extraction of trace chlorsulfuron. Under the optimal experimental conditions, the recovery for chlorsulfuron was in the range of 81.0-110.1% for the water samples, with RSDs ranging from 1.2 to 7.6%.     

Preparation of a magnetic molecularly imprinted polymer by atom‐transfer radical polymerization for the extraction of parabens from fruit juices

A silica‐based surface magnetic molecularly imprinted polymer for the selective recognition of parabens was prepared using a facile and general method that combined atom‐transfer radical polymerization with surface imprinting technique. The prepared magnetic molecularly imprinted polymer was characterized by transmission electron microscopy, Fourier transform infrared spectrometry and physical property measurement. The isothermal adsorption experiment and kinetics adsorption experiment investigated the adsorption property of magnetic molecularly imprinted polymer to template molecule. The four parabens including methylparaben, ethylparaben, propylparaben, and butylparaben were used to assess the rebinding selectivity. An extraction method, which used magnetic molecularly imprinted polymer as adsorbents coupled with high‐performance liquid chromatography for the determination of the four parabens in fruit juice samples was developed. Under the optimal conditions, the limits of detections of the four parabens were 0.028, 0.026, 0.021, and 0.026 mg/L, respectively. The precision expressed as relative standard deviation ranging from 2.6 to 8.9% was obtained. In all three fortified levels, recoveries of parabens were in the range of 72.5–89.4%. The proposed method has been applied to different fruit juice samples including orange juice, grape juice, apple juice and peach juice, and satisfactory results were obtained.     

Development of a molecularly imprinted polymer for selective extraction of bisphenol A in water samples

A cross‐linked methacrylate molecularly imprinted polymer (poly‐4‐vinylpyridine‐co‐trimethylolpropane‐trimethacrylate) selective for bisphenol A (BPA) was synthesized, using a fluorinated BPA derivative (4,4′‐(hexafluoroisopropylidene)‐diphenol) as a mimic template, and applied to the analysis of real‐world samples of process and potable waters. The molecularly imprinted polymer also showed a high affinity and selectivity for 17‐β‐estradiol and ethynylestradiol. A method to analyze BPA, 17‐β‐estradiol, and ethynylestradiol at ultratrace levels was thus developed from a screening procedure to monitor endocrine‐disrupting chemicals in water samples. The method consists of the BPA‐selective cleanup by molecularly imprinted SPE using cartridges packed with the polymer developed, its recovery by stir bar sorptive extraction after ad hoc derivatization to obtain the corresponding BPA‐acetate, and its analysis by GC‐time window‐SIM‐MS after online thermal desorption. The method showed good linearity in the working range (R²=0.9969), high repeatability (RSD% <10.1), recoveries always above 90%, and very low LOD (10 pg/L) and LOQ (1 ng/L) and can easily be extended to the determination of 17‐β‐estradiol and ethynylestradiol ultratraces. The method's effectiveness was evaluated by analyzing the real‐world water samples; it enabled preconcentration and detection of BPA at ultratrace levels.     

Molecularly imprinted on-line solid-phase extraction combined with flow-injection chemiluminescence for the determination of tetracycline

A molecularly imprinted polymer solid phase extraction (MISPE) method combined with flow-injection chemiluminescence (FI-CL) for the determination of residual tetracycline (TC) in fish samples is presented. The molecularly imprinted polymer (MIP) of TC was synthesized and particles of this MIP were packed into a polytetrafluoroethylene (PTFE) tube, which was connected into the sampling loop of an eight-way injection valve and served as the MISPE column for on-line selective adsorption of TC. The eluent (CH3CN : HNO3 (0.01 mol L(-1)) = 4 ratio 1, v ratio v) was used for extracting the adsorbed TC, which could be detected by its good enhancing effect on the CL reaction between Ce(iv) and rhodamine B. The CL intensity is linear to TC concentration in the range from 4 x 10(-9) to 4 x 10(-7) g mL(-1). The detection limit is 1 x 10(-9) g mL(-1) (3 sigma) and the relative standard deviation is 2.4% (n = 9). The conditions of preconcentration, extraction and CL reaction were carefully studied. The selectivity experiment shows that the selectivity and sensitivity of the CL method could be improved greatly when MIP was used as a recognition material in SPE. However, the MISPE column interacted indiscriminately with oxytetracycline (OTC) with a 49 +/- 2% binding. An intermediate differential pulsed elution (DPE) step using 3% acetic acid as eluent was employed to remove OTC and other interfering substances. The proposed MISPE-CL method has been applied successfully to the determination of TC in fish samples. At the same time, the binding characteristics of the polymer to tetracycline were evaluated by batch and dynamic methods.     

Molecularly imprinted polymers: An analytical tool for the determination of benzimidazole compounds in water samples

Molecularly imprinted polymers (MIPs) for benzimidazole compounds have been synthesized by precipitation polymerization using thiabendazole (TBZ) as template, methacrylic acid as functional monomer, ethyleneglycol dimethacrylate (EDMA) and divinylbenzene (DVB) as cross-linkers and a mixture of acetonitrile and toluene as porogen. The experiments carried out by molecularly imprinted solid phase extraction (MISPE) in cartridges demonstrated the imprint effect in both imprinted polymers. MIP–DVB enabled a much higher breakthrough volume than MIP–EDMA, and thus was selected for further experiments. The ability of this MIP for the selective recognition of other benzimidazole compounds (albendazole, benomyl, carbendazim, fenbendazole, flubendazole and fuberidazole) was evaluated. The obtained results revealed the high selectivity of the imprinted polymer towards all the selected benzimidazole compounds.An off-line analytical methodology based on a MISPE procedure has been developed for the determination of benzimidazole compounds in tap, river and well water samples at concentration levels below the legislated maximum concentration levels (MCLs) with quantitative recoveries. Additionally, an on-line preconcentration procedure based on the use of a molecularly imprinted polymer as selective stationary phase in HPLC is proposed as a fast screening method for the evaluation of the presence of benzimidazole compounds in water samples.     

Online molecularly imprinted solid‐phase extraction coupled to liquid chromatography‐tandem mass spectrometry for the determination of hormones in water and sediment samples

The molecularly imprinted SPE directly coupled to RP LC‐MS/MS method has been developed and successfully validated for the determination of six hormones in water and sediment samples. The method is based on the use the home‐made column filled with a molecularly imprinted sorbent (imprinted against estrogens) that was used under nonaqueous conditions. Thus, its high selectivity could be utilized resulting in low matrix components’ coextraction. The method showed excellent recovery (92–105%) and satisfactory sensitivity (LOQs water: 1.9–4.0 ng/L; LOQs sediment: 0.2–0.5 ng/g). The intra‐ and interprecision for water and sediment was in the range of 4.0–6.0% and 4.4–7.6%, respectively. Finally, 20 water and sediment samples collected from the Svratka river were analyzed. Only estrone was quantified in eight water samples (4.4–7.1 ng/L); no analytes were found in sediment samples.     

Molecularly imprinted SPE and MEKC with in-capillary sample preconcentration for the determination of digoxin in human urine

Molecularly imprinted solid-phase extraction (MISPE) combined with MEKC was used for clean-up, preconcentration and determination of digoxin in the presence of its aglycon digoxin (digoxigenin) in human urine samples. In addition, the use of an in-capillary sample concentration electrophoretic technique by sweeping was investigated to enhance the concentration sensitivity in MEKC. The highly selective, fast and effective sample pretreatment by MISPE along with the preconcentration by sweeping could overcome the low sensitivity of the highly efficient capillary electrophoresis separation with UV detection. The optimization of the variables affecting the separation as well as MISPE conditions procedure was carried out to select the best conditions of selectivity and sensitivity to determine digoxin at low concentration levels in urine. To demonstrate the suitability of the developed method several analytical characteristics (selectivity, linearity, accuracy, precision, and LOD) were evaluated. Satisfactory results were obtained in terms of linearity (r > 0.99), recovery (95.4-96.5% with RSD from 1.3% to 2.6%), precision (RSD from 0.3% to 1.7% for migration times and from 2.1% to 7.3% for corrected peak areas), and sensitivity (LODs of 6 μg/L with 5 mL of sample or 1.2 μg/L with 25 mL). The proposed MISPE-MEKC method was satisfactorily applied to the analysis of spiked human urine samples achieving a concentration factor up to 7500-fold.     

Development of selective and chemically stable coating for stir bar sorptive extraction by molecularly imprinted technique

A novel stir bar coated with molecularly imprinted polymer (MIP) as selective extraction phase for sorptive extraction of triazine herbicides was developed. The stir bar was prepared by chemically bonding the MIP to the glass bar to improve its stability. A homogeneous and porous structure was observed on the stir bar surface. Extraction performance shows that the MIP-coated stir bar has stronger affinity to the template molecule terbuthylazine as compared with that of the reference stir bar without addition of template. Owning to the shape and structural compatibility, the obtained stir bar also demonstrated specific selectivity to the structural related-compounds of nine triazines, and thus can be applied to simultaneous determination of these compounds from complex samples coupled with high performance liquid chromatography. Four complex samples with different matrix, including rice, apple, lettuce and soil were used to evaluate this proposed method. The limits of detection obtained are in the range of 0.04-0.12 μg L⁻¹, and the recoveries for the spiked rice, apple, lettuce and soil samples were 80.8-107.7%, 80.6-107.8%, 72.0-109.8% and 89.0-114.8% with RSD from 1.2 to 7.9%, respectively. Moreover, this MIP-coated stir bar was firm, durable and can be prepared simply and reproducibly. The developed coating method would be useful to prepare a range of selective stir bars in order to extend the applicability of stir bar sorptive extraction (SBSE) in complex sample analysis.     

Rapid preparation of molecularly imprinted polymers by custom‐made microwave heating for analysis of atrazine in water

The rapid preparation of an atrazine‐imprinted polymer in a cost‐effective custom‐made microwave reactor was demonstrated. The polymerization reaction was accelerated by microwave heating, and the preparation time was greatly shortened (to 1 h). The resulting polymer was successfully applied as solid‐phase extraction adsorbent for the selective extraction and preconcentration of atrazine in environmental water samples. The binding capacity of the polymer was 1.11 mg/g polymer. The polymer provided selectivity with higher recovery of atrazine than of other interfering related contaminants. The proposed method had good limits of detection and quantitation at 0.20 and 0.60 ng/mL, respectively. The recoveries were from 83 to 89% at two spiking levels, with relative standard deviations less than 5%. This method was successfully applied to determine the atrazine levels in environmental water samples.     

A nanosized cadmium(II)-imprinted polymer for use in selective trace determination of cadmium in complex matrices

We describe a nanosized Cd(II)-imprinted polymer that was prepared from 4-vinyl pyridine (the functional monomer), ethyleneglycol dimethacrylate (the cross-linker), 2,2′-azobisisobutyronitrile (the radical initiator), neocuproine (the ligand), and Cd(II) (the template ion) by precipitation polymerization in acetonitrile as the solvent. The imprinted polymer was characterized by X-ray diffraction, thermogravimetric analysis, differential thermal analysis, and scanning electron microscopy. The maximum adsorption capacity of the nanosized sorbent was calculated to be 64 mg g^?1. Cadmium(II) was then quantified by FAAS. The relative standard deviation and limit of detection are 4.2 % and 0.2 μg L^?1, respectively. The imprinted polymer displays improve selectivity for Cd(II) ions over a range of competing metal ions with the same charge and similar ionic radius. This nanosized sorbent is an efficient solid phase for selective extraction and preconcentration of Cd(II) in complex matrices. The method was successfully applied to the trace determination of Cd(II) in food and water samples.

Development of novel molecularly imprinted solid-phase microextraction fibers and their application for the determination of antibiotic drugs in biological samples by SPME-LC/MS(n)

Novel molecularly imprinted polymer (MIP)-coated fibers for solid-phase microextraction (SPME) fibers were prepared by using linezolid as the template molecule. The characteristics and application of these fibers were investigated. The polypyrrole, polythiophene, and poly(3-methylthiophene) coatings were prepared in the electrochemical polymerization way. The molecularly imprinted SPME coatings display a high selectivity toward linezolid. Molecularly imprinted coatings showed a stable and reproducible response without any influence of interferents commonly existing in biological samples. High-performance liquid chromatography with spectroscopic UV and mass spectrometry (MS) detectors were used for the determination of selected antibiotic drugs (linezolid, daptomycin, amoxicillin). The isolation and preconcentration of selected antibiotic drugs from new types of biological samples (acellular and protein-free simulated body fluid) and human plasma samples were performed. The SPME MIP-coated fibers are suitable for the selective extraction of antibiotic drugs in biological samples.     

On-Line Preconcentration and Analysis of Metribuzin Residues in Corn Fields by Use of a Molecularly Imprinted Polymer

A molecularly imprinted polymer as a selective solid-phase extraction adsorbent for efficient preconcentration and analysis of metribuzin residues in corn fields has been synthesised and evaluated. Results showed that molecular imprinting of the polymer was highly effective and the polymer had high affinity and selectivity for metribuzin in water-containing systems. A monolithic column containing molecularly imprinted polymer was prepared and used for on-line preconcentration, separation, and detection of metribuzin residues in soil sampled during investigation of the degradation of the herbicide metribuzin in corn fields. The detection limit of the method was 8.3 × 10^?4 mg kg^?1, recovery was between 94.9% and 103%, and RSD in analysis of soil samples was less than 3.2%.