基于聚(4-乙烯基苯酚)衬底修饰层喷墨打印的小分子有机半导体薄膜制备和表征

采用旋涂法预先在SiO2衬底表面形成一层聚(4-乙烯基苯酚)(PVP)作为表面修饰层,以喷墨打印的6,13-双(三异丙基甲硅烷基乙炔基)并五苯(TIPS并五苯)作为有源层制作有机薄膜晶体管,有效改善了有机半导体薄膜的形貌。采用真空热蒸镀工艺制备源漏电极,形成底栅顶接触结构的有机薄膜晶体管(OTFT)器件。作为对比,在未经过表面修饰的SiO2衬底上采用相同条件打印TIPS并五苯薄膜晶体管,发现在经过PVP修饰的SiO2衬底上打印的单点厚度更均匀,咖啡环效应被抑制或被消除;而通过多点交叠打印形成的矩形薄膜的晶粒尺寸更大,相应的OTFT器件具有更高的场效应迁移率。在有PVP修饰层的衬底上制作的OTFT,器件在饱和区的平均场效应迁移率达到了0.065 cm2·V-1·s-1;而直接在SiO2衬底上制作的器件,相应的平均场效应迁移率仅为0.02 cm2·V-1·s-1。     

基于聚(4-乙烯基苯酚)衬底修饰层喷墨打印的小分子有机半导体薄膜制备和表征

采用旋涂法预先在SiO₂衬底表面形成一层聚（4-乙烯基苯酚）（PVP）作为表面修饰层,以喷墨打印的6,13-双（三异丙基甲硅烷基乙炔基）并五苯（TIPS并五苯）作为有源层制作有机薄膜晶体管,有效改善了有机半导体薄膜的形貌。采用真空热蒸镀工艺制备源漏电极,形成底栅顶接触结构的有机薄膜晶体管（OTFT）器件。作为对比,在未经过表面修饰的SiO₂衬底上采用相同条件打印TIPS并五苯薄膜晶体管,发现在经过PVP修饰的SiO₂衬底上打印的单点厚度更均匀,咖啡环效应被抑制或被消除;而通过多点交叠打印形成的矩形薄膜的晶粒尺寸更大,相应的OTFT器件具有更高的场效应迁移率。在有PVP修饰层的衬底上制作的OTFT,器件在饱和区的平均场效应迁移率达到了0.065 cm²·V^-1·s^-1;而直接在SiO₂衬底上制作的器件,相应的平均场效应迁移率仅为0.02 cm²·V^-1·s^-1。     

Ta_2O_5-PMMA复合栅绝缘层对OFETs性能的影响（英文）

选用五氧化二钽(Ta_2O_5)-聚甲基丙烯酸甲酯(PMMA)复合材料作为栅绝缘层制备了并五苯有机场效应晶体管(OFETs)。通过在Ta_2O_5表面旋涂一层PMMA可以降低栅绝缘层的表面粗糙度,增大其场效应晶体管的迁移率。研究了厚度在20~60 nm范围内的PMMA对复合绝缘层表面形貌、粗糙度以及器件电学性能的影响。结果表明,当PMMA厚度为40 nm时,器件的电学性能最佳。与单一的Ta_2O_5栅绝缘层器件相比,其场效迁移率由4.2×10~(-2)cm~2/(V·s)提高到0.31 cm~2/(V·s);栅电压增加到-20 V时,开关电流比由2.9×10~2增大到2.9×10~5。     

不同绝缘层上生长的并五苯薄膜及其OTFT器件性能的研究

分别以SiO₂和PMMA为绝缘层材料制备了底栅顶接触结构的OTFT器件,得到以PMMA为绝缘层的器件具有更好的性能,其场效应迁移率为0.207 cm2·Vs-1,开关电流比为4.93×103,阈值电压为-4.3 V;而以SiO₂为绝缘层的器件,其场效应迁移率仅为0.039 cm2·Vs-1,开关电流比为5.98×102,阈值电压为-5.4 V。为分析器件性能差异的原因,测得了SiO₂和PMMA薄膜表面的AFM图谱及其上沉积并五苯薄膜后的AFM和XRD图谱。通过AFM图谱发现PMMA表面较SiO₂表面粗糙度小,其表面粗糙度的均方根值为0.216 nm,而二氧化硅薄膜表面粗糙度的均方根值为1.579 nm;且发现在PMMA上生长的并五苯薄膜的成膜质量优于在SiO₂,具有较大的晶粒尺寸和较少的晶粒间界。通过XRD图谱发现在PMMA上生长的并五苯薄膜具有明显的衍射峰,进一步证明了在PMMA上生长的并五苯薄膜具有更好的结晶状况,将更有利于载流子的传输。     

Ta2O5-PMMA复合栅绝缘层对OFETs性能的影响

选用五氧化二钽（Ta₂O₅）-聚甲基丙烯酸甲酯（PMMA）复合材料作为栅绝缘层制备了并五苯有机场效应晶体管（OFETs）。通过在Ta₂O₅表面旋涂一层PMMA可以降低栅绝缘层的表面粗糙度,增大其场效应晶体管的迁移率。研究了厚度在20~60 nm范围内的PMMA对复合绝缘层表面形貌、粗糙度以及器件电学性能的影响。结果表明,当PMMA厚度为40 nm时,器件的电学性能最佳。与单一的Ta₂O₅栅绝缘层器件相比,其场效迁移率由4.2×10^-2 cm²/（V·s）提高到0.31 cm²/（V·s）;栅电压增加到-20 V时,开关电流比由2.9×10²增大到2.9×10⁵。     

蒸镀法制备全有机并五苯薄膜场效应晶体管

以全蒸镀方法在真空室内一次性制备了正装结构的全有机并五苯薄膜场效应晶体管。正装结构全蒸镀法有利于简化工艺制备程序,缩小器件尺寸,提高集成度。制备的绝缘层厚度仅为50nm的全有机薄膜场效应晶体管,器件的工作电压降至10V,相同电压下饱和输出电流有了明显提高。筛选适当的有机绝缘材料,改善全有机薄膜场效应晶体管有源层/绝缘层的界面性能,使阈值电压几乎降至0V,场效应迁移率提高了3倍多,输出饱和电流也有了明显的提高。     

基于栅绝缘层表面修饰的有机场效应晶体管迁移率的研究进展

栅绝缘层的表面性质对有机场效应晶体管（OFETs）的半导体薄膜的形貌、晶粒生长的有序性和载流子的传输有着重大的影响．研究表明,通过改进栅绝缘层的表面性质,可以有效提高有机场效应晶体管的迁移率．本文综述了OFETs绝缘层表面的粗糙度和表面能对OFETs迁移率的影响,重点探讨了栅绝缘层表面修饰常用的方法,即自组装单层（SAMs）修饰和聚合物修饰与迁移率改进之间的研究进展．最后,展望了该研究方向未来可能的发展趋势．     

对以并五苯和酞菁铜为不同有源层的有机薄膜晶体管特性研究

通过扫描电镜和X射线衍射对SiO₂衬底上生长并五苯和酞菁铜薄膜的表面形貌进行表征,并得到在SiO₂衬底上生长的并五苯薄膜是以岛状结构生长,其大小约为100nm,且薄膜有较好的结晶取向,呈多晶态存在. 酞菁铜薄膜则没有表现出明显的生长机理,其呈非晶态存在. 还对通过掩膜的方法制作得以酞菁铜和并五苯为有源层的顶栅极有机薄膜晶体管的特性进行了研究. 有源层的厚度为40nm,绝缘层SiO₂的厚度为250nm,器件的沟道宽长比(W/关键词： 有机薄膜晶体管 并五苯薄膜 酞菁铜薄膜 μ_EF)')" href="#">场效应迁移率(μ_EF)     

绝缘层修饰对喷墨打印有机场效应晶体管形貌和性能的影响

通过对OTFT绝缘层SiO_2表面分别采用十八烷基三氯硅烷(OTS)处理和原子层沉积薄层氧化铝的修饰方式,制备了喷墨打印有机薄膜晶体管并研究了修饰前后绝缘层的表面形貌、接触角及有源层的物相结构。虽然绝缘层的表面形貌在修饰前后变化不大,但是表面接触角和打印后有源层的物相结构有较大差别。OTS处理和沉积氧化铝修饰后,器件的迁移率比修饰前分别增大了4倍和9倍,而开关比则分别增大了1个和4个数量级。修饰后的最大迁移率可达0.35 cm~2/(V·s),开关比可达6.0×10~6。     

低栅极电压控制下带有phenyltrimethoxysilane单分子自组装层的有机薄膜晶体管场效应特性研究

制作了底栅极顶接触有机薄膜晶体管器件,60 nm的pentacene被用作有源层,120 nm热生长的SiO₂作为栅极绝缘层.通过采用不同自组装修饰材料对器件的有源层与栅极绝缘层之间的界面进行修饰,如octadecyltrichlorosilane （OTS）,phenyltrimethoxysilane （PhTMS）,来比较界面修饰层对器件性能的影响.同时对带有PhTMS修饰层的OTFTs器件低栅极电压调制下的场效应行为及其载流子的传输机理进行研究.结果得到,当|V 关键词： 有机薄膜晶体管 自组装单分子层 场效应迁移率 低栅极调制电压     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.