量子阱数变化对InGaN/GaN发光二极管瞬态响应的影响（英文）

理论上研究了当InGaN发光二极管(LED)有源区的量子阱数变化时,LED的大信号瞬态响应特性与这种变化的关系。结果来自于LED等效电路模型的SPICE模拟,模型参数的确定通过拟合已测量的LED的实验数据及模拟结果来实现。结果表明,LED光脉冲的上升时间随量子阱数的增加而增加,由3个量子阱构成的有源区是LED的优化结构。     

太赫兹量子级联激光器中有源区上激发态电子向高能级泄漏的研究

利用热力学统计理论和激光器输出特性理论,建立了太赫兹量子级联激光器(THz QCL)有源区中上激发态电子往更高能级电子态泄漏的计算模型,以输出功率度量电子泄漏程度研究分析了晶格温度和量子阱势垒高度对电子泄漏的影响.数值仿真结果表明,晶格温度上升会加剧电子泄漏,并且电子从上激发态泄漏到束缚态的数量大于泄漏到阱外连续态,同时温度的上升也会降低激光输出功率.增加量子阱势垒高度能抑制电子泄漏,并且有源区量子阱结构中存在一个最优量子阱势垒高度. THz QCL经过最优量子阱势垒高度优化后,工作温度得到提升,其输出功率相比于以往的结果也有所提高.研究结果对优化THz QCL有源区结构、抑制电子泄漏和改善激光器输出特性有指导作用.     

In组分渐变提高InGaN/GaN多量子阱发光二极管发光性能

利用金属有机物化学气相沉积系统在蓝宝石衬底上通过有源层的变温生长,得到In组分渐变的量子阱结构,从而获得具有三角形能带结构的InGaN/GaN多量子阱发光二极管(LED)(简称三角形量子阱结构LED).变温光致发光谱结果表明,相对于传统具有方形能带结构的量子阱LED(简称方形量子阱结构LED),三角形量子阱结构有效提高了量子阱中电子和空穴波函数的空间交叠,从而增加了LED的内量子效率;电致发光谱结果表明,三角形量子阱结构LED器件与传统结构LED器件相比,明显改善了发光峰值波长随着电流的蓝移现象.通过以上     

不规则H形量子势垒增强AlGaN基深紫外发光二极管性能

针对AlGaN基多量子阱中有效的平衡载流子注入问题,研究了有源区势垒层中Al组分调制形成的非规则H形量子势垒对AlGaN基深紫外发光二极管(LED)器件性能的影响及载流子的输运行为。研究发现,与多量子阱中常用的单Al组分势垒相比,加入Al组分较高的双尖峰势垒可以有效地提高内量子效率和光输出功率。进一步研究表明,电子在有源区因凸起的尖峰势垒而得到了有效的阻挡,减少了电子的泄露,而空穴获得更多的动能从而穿过较高的势垒进入有源区。因此,采用非对称H形量子势垒的深紫外LED器件中载流子输运实现了较好的平衡,量子阱中的载流子复合速率远高于普通的深紫外发光二极管。     

选择性p型量子阱垒层掺杂在双波长发光二极管光谱调控中的作用

采用软件理论分析的方法对选择性p型掺杂量子阱垒层在InGaN双波长发光 二极管(LED)中的光谱调控作用进行模拟分析.分析结果表明, 选择性p型掺杂对量子阱中电子和空穴浓度分布的均衡性起到一定的调控作用, 在适当选择p型掺杂量子阱垒层层数的条件下,能够改善量子阱中载流子的 辐射复合速率, 降低溢出电子浓度,从而有效提高芯片内量子效率,并减缓内量子效率随驱动 电流增大而快速下降的趋势.随着活性层量子阱增加到特定数量, 选择性p型掺杂的调控效果更加明显, LED芯片的双波长发光峰强度达到基本均衡.     

引入n型InGaN/GaN超晶格层提高量子阱特性研究

利用金属有机物化学气相淀积技术在蓝宝石衬底上生长了InGaN/GaN量子阱结构. 研究了引入n型InGaN薄层或InGaN/GaN超晶格层的量子阱特性,结果表明通过引入n型InGaN薄层或InGaN/GaN超晶格层缓解了量子阱有源区中的应力,改善了多量子阱表面形貌,减少了V型缺陷密度,而且提高了多量子阱的光致发光强度,从而也改进了LED的发光效率. 关键词： InGaN/GaN多量子阱 原子力显微镜 X射线双晶衍射 光致发光     

近800nm波长张应变GaAsP/A1GaAs量子阱激光器有源区的设计

张应变GaAs_(1-x)P_x量子阱是高性能大功率半导体激光器的核心有源区,基于能带结构分析优化其结构参数具有重要的应用指导意义.首先,基于6×6 Luttinger-Kohn模型,采用有限差分法计算了张应变GaAs_(1-x)P_x量子阱的能带结构,得到了第一子带间跃迁波长固定为近800 nm时的阱宽-阱组分关系,即随着阱组分x的增加,需同时增大阱宽,且阱宽较大时靠近价带顶的是轻空穴第一子带lh_1,阱宽较小时靠近价带顶的是重空穴第一子带hh_1.计算并分析了导带第一子带c_1到价带子带lh_1和hh_1的跃迁动量矩阵元.针对808 nm量子阱激光器,模拟计算了阈值增益与阱宽的关系,得到大阱宽有利于横磁模激射,小阱宽有利于横电模激射.进一步考虑了自发辐射和俄歇复合之后,模拟计算了808 nm量子阱激光器的阱宽与阈值电流密度的关系,阱宽较大时载流子对高能级子带的填充使得阈值电流密度增加,而阱宽较小时则是低的有源区光限制因子导致阈值电流密度升高,因此存在一最佳的阱宽-阱组分组合,可使阈值电流密度达到最小.本文的模拟结果可对张应变GaAs_(1-x)P_x量子阱激光器的理论分析和结构设计提供理论指导.     

载流子复合机制对InGaN多量子阱蓝光LED调制带宽的影响

通过设计InGaN多量子阱LED有源区的不同结构,研究了载流子复合机制对LED调制速度的影响。结果显示,由于窄量子阱LED的载流子空间波函数重叠几率更高,且电子泄露效应更显著,所以复合速率更快,调制带宽更高。In组分为1%的InGaN量子垒LED可提高辐射复合的权重,使得调制带宽高于GaN量子垒LED;In组分为5%时,电子泄露和俄歇复合占据主导地位,且由于这两种复合机制复合速率很快,所以调制带宽显著提高。     

近800 nm波长张应变GaAsP/AlGaAs量子阱激光器有源区的设计

张应变GaAs_1-xP_x量子阱是高性能大功率半导体激光器的核心有源区,基于能带结构分析优化其结构参数具有重要的应用指导意义.首先,基于6×6 Luttinger-Kohn模型,采用有限差分法计算了张应变GaAs_1-xP_x量子阱的能带结构,得到了第一子带间跃迁波长固定为近800 nm时的阱宽-阱组分关系,即随着阱组分x的增加,需同时增大阱宽,且阱宽较大时靠近价带顶的是轻空穴第一子带lh₁,阱宽较小时靠近价带顶的是重空穴第一子带hh₁.计算并分析了导带第一子带c₁到价带子带lh₁和hh₁的跃迁动量矩阵元.针对808 nm量子阱激光器,模拟计算了阈值增益与阱宽的关系,得到大阱宽有利于横磁模激射,小阱宽有利于横电模激射.进一步考虑了自发辐射和俄歇复合之后,模拟计算了808 nm量子阱激光器的阱宽与阈值电流密度的关系,阱宽较大时载流子对高能级子带的填充使得阈值电流密度增加,而阱宽较小时则是低的有源区光限制因子导致阈值电流密度升高,因此存在一最佳的阱宽-阱组分组合,可使阈值电流密度达到最小.本文的模拟结果可对张应变GaAs_1-xP_x量子阱激光器的理论分析和结构设计提供理论指导.     

InGaN/GaN多量子阱LED载流子泄漏与温度关系研究

通过测量光电流,直接观察了InGaN/GaN量子阱中载流子的泄漏程度随温度升高的变化关系。当LED温度从300K升高到360K时,在相同的光照强度下,LED的光电流增大,说明在温度上升之后,载流子从量子阱中逃逸的数目更多,即载流子泄漏比例增大。同时,光电流的增大在激发密度较低的时候更为明显,而且光电流随温度的增加幅度与激发光子的能量有关。用量子阱-量子点复合模型能很好地解释所观察到的实验现象。实验结果直接证明,随着温度的升高,InGaN/GaN量子阱中的载流子泄漏将显著增加,而且在低激发密度下这一效应更为明显。温度升高导致的载流子泄漏增多是InGaN多量子阱LED发光效率随温度升高而降低的重要原因。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.