壳聚糖/聚乙烯醇共混超细纤维的制备及紫外光交联研究

用静电纺丝法制备壳聚糖/聚乙烯醇的共混超细纤维,采用扫描电镜考察了纺丝液浓度、共混物配比、喷丝口内径对纤维形貌的影响.此外,为减少壳聚糖/聚乙烯醇纤维膜的溶胀变形,在上述体系中加入可光交联的单体二缩三乙二醇双甲基丙烯酸酯(TEGDMA)、引发剂2-羟基-2-甲基-1苯基丙酮(1173),对电纺纤维进行紫外光交联.结果表明,当壳聚糖与聚乙烯醇质量比为8:2的共混体系中加入占混合溶液质量分数4%的TEGDMA、0.12%的1173作为交联剂时,所得的无纺布纤维直径比较均一,平均约为200 nm,经光交联处理后其耐水性能得到提高.     

静电纺聚丙烯腈纳米纤维晶态结构及取向的形成

采用新型流动水浴收集方式制备出连续单向排列的静电纺聚丙烯腈(PAN)纳米初生纤维,收集静电纺丝不同阶段的静电纺PAN纳米纤维,并在热水中进行后牵伸,使其伸长至原长的2倍、3倍.通过扫描电子显微镜(SEM)、广角X射线衍射(WAXD)等方法对静电纺丝过程不同阶段的PAN纳米纤维的形貌、直径、致密性、晶态结构及取向进行了表征.研究表明,(1)在静电纺丝过程中PAN纺丝液射流受到牵伸作用,静电纺PAN纳米纤维的晶态结构形成并逐渐完善.纳米纤维的直径随着静电纺丝过程逐渐减小(从664 nm减小至353 nm),结晶度从42.55％增加至47.76％,晶区取向由37.48％提高至43.93％.纳米纤维致密性也逐渐提高(密度由1.1917 g/cm3增加至1.1943 g/cm3).(2)静电纺丝过程进入PAN射流溶剂含量较低的阶段后,继续通过静电纺丝过程提高纳米初生纤维晶态结构及取向的效果很有限,而通过热水后牵伸过程可进一步使晶态结构及取向得到有效果的完善.研究同时发现,静电纺初生纤维的晶态结构及取向与其在热水牵伸过程中的进一步完善具有相关性.     

PLGA/明胶共混体系的静电纺丝研究

采用静电纺丝技术制备了聚乳酸乙醇酸(PLGA)/明胶(Gt)的复合超细纤维, 考察了溶液浓度、电压及流速对纤维形貌的影响. 研究了不同明胶比例的纤维膜的微观形貌和干湿态的力学性能. 结果表明, 在溶液浓度0.12 g/mL, 电压7.5 kV, 流速0.8 mL/h条件下, 所得PLGA/Gt复合纤维直径较小, 粗细较均匀且缺陷少. 含有明胶的复合纤维直径远小于PLGA单纺纤维直径, 明胶的加入降低了膜的拉伸强度和断裂伸长率, 提高了膜的亲水性. 经PBS浸泡后, 复合膜的弹性得到加强. 明胶质量分数为5%和10%时, 纤维直径分布较窄, 当明胶的质量分数增加至15%时, 纤维的直径分布变宽.     

电纺聚乙烯醇超细纤维膜的性能研究

由电纺制备聚乙烯醇(PVA)超细纤维膜,以扫描电镜观察纤维的微观形貌,用X射线衍射研究超细纤维膜的结晶行为,并测定了PVA超细纤维膜的力学性能和吸水性.结果表明,PVA超细纤维的平均直径为(184±26)nm,超细纤维中PVA的结晶度和晶体有序程度较浇铸膜低.超细纤维膜的拉伸强度、模量和断裂伸长率均较浇铸膜差,吸水率在300%以上,高于浇铸膜.     

分子量对聚氨酯创伤敷料静电纺纤维膜性能的影响

为了研究可应用于创伤敷料的聚氨酯(PU)电纺纤维的最小分子量,本文使用静电纺丝技术制备了三种较低分子量(10k,50k,70k)的PU纤维膜。结果表明,PU的可纺性随着分子量的增加而增加。PU的分子量越大,纤维的缠结越紧密,分布越均匀,纤维形态越好。当PU的分子量达到70k,纺丝液浓度为18wt%时,电纺纤维膜具有优异的机械性能、良好的透湿性吸液能力和优良的细胞的相容性。可以看出,当通过静电纺丝技术制备PU创伤敷料膜时,PU分子量的最低要求为70,000。     

采用静电纺丝/非溶剂致相分离制备聚丙烯腈多孔超细纤维的研究

以聚丙烯腈/二甲基亚砜/N,N'-二甲基甲酰胺三元体系为纺丝液、3℃水浴为接收介质,通过静电纺丝制备了具有纳米孔结构的静电纺聚丙烯腈多孔超细纤维.探讨了溶剂比例、接收介质、聚丙烯腈浓度、纺丝电压及接收距离等因素对纤维直径和表面孔隙率的影响.结果表明最佳制备条件为混合溶剂质量比1∶1、纺丝电压16 kV、聚丙烯腈浓度15 wt%、接收距离5 cm、纺丝速率0.7 mL/h、环境温度25℃、相对湿度40%～70%.在此条件下得到的聚丙烯腈多孔超细纤维直径在420～490 nm,平均直径468 nm,表面孔隙率3.4%,纤维内部形成大量孔径为8～30 nm的孔结构,且孔径分布均匀,孔形状相对一致.N2吸附脱附测试表明,聚丙烯腈多孔纤维的BET比表面积达43.86 m2/g,是相同直径无孔聚丙烯腈纤维比表面积理论值的6倍.通过研究聚丙烯腈/(二甲基亚砜+N,N'-二甲基甲酰胺)/水的三元相图,提出非溶剂致相分离是主要成孔机理.     

PVA/SiO2-TiO2杂化电纺纤维膜的形态与性能

以正硅酸乙酯(TEOS)、钛酸四丁酯(TBT)和聚乙烯醇(PVA)为原料, 用溶胶凝胶法制备了PVA/(SiO2-TiO2)杂化纺丝液, 将其电纺成纤维膜. 红外光谱结果证实, PVA的羟基与TEOS和TBT水解后的羟基发生了缩合反应, 杂化电纺纤维膜以网络结构形式相结合; X射线衍射分析表明, 杂化电纺纤维膜的结晶度比纯PVA电纺纤维膜小; 扫描电镜表明, 随杂化纤维膜中无机相含量的增加, 纤维的直径不断增加, 纤维出现一定的弯曲和扭曲, 并伴有少量带状结构的纤维; 紫外-可见光谱结果表明, TiO2的引入增加了纤维膜的抗紫外性; TGA热分析结果表明, 杂化纤维膜的耐热性能优于纯PVA电纺纤维膜的; 耐水性和稳定性测试表明, 杂化纤维膜的耐水性和稳定性优于纯PVA和PVA/SiO2电纺纤维膜的.     

氨基官能化聚乳酸电纺纤维的制备、 表征和应用

通过聚乳酸(PLA)和氨基丙基三乙氧基硅烷(KH550)混合进行静电纺丝制备氨基官能化聚乳酸纳米纤维. 采用滴定法测定了纤维表面氨基含量, 证明当KH550的添加量为3%~13%(质量分数)时, 有19%~26%的氨基出现在纤维的表面. 利用场发射扫描电子显微镜、 差示扫描量热(DSC)仪、 接触角测试仪和电子拉伸机对纤维形貌、 PLA的玻璃化转变温度和熔点以及纤维膜的亲水性和力学性能进行了表征. 结果表明, KH550的加入可以在电纺纤维表面引入氨基, 同时使纤维直径变细, 使PLA的玻璃化转变温度上升, 熔点下降, 电纺纤维膜的亲水性略有增加, 力学性能有所下降. 通过吸附将金纳米粒子负载到氨基官能化聚乳酸电纺纤维膜上, 得到负载型催化剂, 对硼氢化钠还原对硝基苯酚的反应具有良好的催化活性和重复使用性.     

聚ε-己内酯/聚吡咯电纺膜的制备与性能

以吡咯(Py)和聚ε-己内酯(PCL)为原料、氯仿为溶剂,并掺杂一定量的十二烷基硫酸钠制备电纺膜,利用三氯化铁的氧化作用原位生成聚吡咯(PPy).对所得到的PCL/PPy电纺膜用红外光谱进行表征,在扫描电镜和透射电镜下观察纤维形貌,并测定力学性能和体积电阻率.结果表明,所生成的PPy以纳米粒子形式附着在电纺纤维表面,随着Py相对于PCL的质量百分含量由0增加到20%,PCL/PPy电纺膜的纤维直径从(730±341)nm逐渐下降至(325±84)nm;膜的拉伸模量和拉伸强度由不含Py的(25.7±0.8)MPa和(2.48±0.14)MPa分别增加至含有20%Py的(48.4±7.6)MPa和(5.05±0.59)MPa,断裂伸长率由(129±27)%下降至(86.2±9.1)%;体积电阻率降低了2～3个数量级.该PCL/PPy电纺纤维膜以期可作为电活性材料用于功能或生物医用领域.     

静电纺丝法制备聚醚酰亚胺纤维膜的结构和介电性能研究

采用静电纺丝法制备了聚醚酰亚胺(PEI)纤维膜,通过扫描电子显微镜(SEM)和偏振红外对PEI纤维膜的微观结构进行研究.实验结果显示纺丝液溶剂决定了PEI的可纺性,以N-甲基吡咯烷酮(NMP)为溶剂时,空气湿度显著地影响纺丝过程以及纤维的形态.在相同纺丝工艺条件下,随着纺丝液浓度的增加,所得PEI取向纤维沿辊筒收集方向的排列规整性提高,纤维平均直径由405 nm增加到3.25 μm.PEI纤维膜介电性能的研究表明,取向纤维膜的介电常数很小,最低可达到1.1,其介电损耗也维持在较低的水平,纤维膜的接收方式以及热牵伸处理会对PEI纤维膜的介电性能产生影响.     

Effect of engineered PLGA‐gelatin‐chitosan/PLGA‐gelatin/PLGA‐gelatin‐graphene three‐layer scaffold on adhesion/proliferation of HUVECs

A three‐layered fibrous scaffold composed of fibers of different diameters in each layer was fabricated in correspondence with the structure of the blood vessels. Effect of solution and electrospinning parameters on morphology and diameters of the fibers were investigated by scanning electron microscopy (SEM), for each layer. The SEM images showed that 18% poly (lactic‐co‐glycolic acid) (PLGA)‐gelatin‐chitosan in 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP)/acid acetic solution resulted in bead‐free fibers for the outer layer. For the middle layer, 18% PLGA‐gelatin in HFIP at 13 kV with 13 cm needle to collector distance was chosen as the optimum condition. SEM imaging demonstrated that by increasing graphene content from 0.5 to 2 wt% in the inner layer (as an electrically conductive/platelet anti‐adhesion material), the fiber diameter decreased from 324.01 ± 58.90 to 288.59 ± 70.77 nm. The effect of gelatin crosslinking on the microstructure of the fibers was also examined. Shrinkage ratio decreased from 57 to below 21% upon crosslinking of the three‐layered scaffold in exposure to vapor of 50% glutaraldehyde solution for 2 hours. Mechanical test showed that tensile strength of the crosslinked three‐layer scaffold in the longitudinal direction was 2.90 MPa which is comparable to that of the vein and artery. The MTT [3‐(4,5‐Dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide] assay displayed cell viability of above 96% for the PLGA‐gelatin containing 2 wt% graphene. SEM analysis revealed that the addition of graphene to PLGA‐gelatin (up to 2%) causes a remarkable improvement in cell adhesion.     

The preparation and characterization of silver‐loading cellulose acetate hollow fiber membrane for water treatment

Silver‐loading asymmetric cellulose acetate (CA) hollow fiber membrane was spun via the dry jet‐wet spinning technique. The spinning solution was prepared by dissolving AgNO₃ and CA in N,N‐dimethylformamide (DMF). The silver ions were reduced in the spinning dope into silver nano‐particles. The morphology of the resulting hollow fibers was examined using a scanning electron microscope and the silver content in the fiber was measured using an inductively coupled plasma atomic emission spectrometer. The antibacterial activities were evaluated. These hollow fibers had a sponge‐like structure and dense inner and outer surfaces. At a 50 k magnification, the pore on the skin layer was not observable, while the nodule size was smaller than 10 nm. The residual silver content of as‐spun hollow fiber was about 60% of the original silver added in the polymer solution. After immersing in water bath for 180 days, the silver content in the bulk of the hollow fibers decreased to 60% and the silver content on the surface reduced to 10%, yet still showed antibacterial activity against Escherichia coli and Staphylococcus aureus. After permeating with water for 5 days, the silver content in the hollow fibers decreased, and did not show antibacterial activity against E. coli and S. aureus. Thus, silver content must be periodically replenished after permeation. The proper range of AgNO₃ in the spinning solution for CA hollow fiber should be about 100–1000 ppm. Copyright © 2005 John Wiley & Sons, Ltd.     

The sol–gel transition of mullite spinning solution in relation to the formation of ceramic fibers

Continuous mullite ceramic fibers were fabricated by a sol–gel dry spinning technique. The sol was prepared from an aqueous solution of aluminum nitrate (AN), aluminum isopropoxide (AIP) and tetraethylorthosilicate (TEOS). The sol–gel transition was investigated by measuring the volume, the solid content, the viscosity and the rheological properties of the solution. Shear viscosity η of the mullite sol varied dynamically with concentrating time and temperature. Combine size analysis of sol particles and TEM analysis on this basis, the growth character of sol particles agglomeration and its structural evolution were discussed. By adjusting the temperature, the gelling degree could stabilize at a certain value and the sol–gel transition could be transferred to the spinning line. Continuous fibers were spun from such sols immediately before gelling in a laboratory dry spinning apparatus. The spinneret contained thirty circular holes, each having a diameter of 0.2 mm. The temperature inside the spinning channel was 100–120 °C, the winding speed was 100–300 m/min. Sintering of the precursor fibers at 1,100 °C yields crack-free mullite ceramic fibers.     

Structures and cyclization behaviors of gel-spun cellulose/polyacrylonitrile composite fibers

Polyacrylonitrile (PAN)/cellulose composite fibers have been produced by dry-jet gel spinning through their co-solution. The rheological properties of PAN/cellulose/dimethylacetamide/LiCl solutions containing different cellulose contents from 0 to 10 wt% were characterized, and 5 wt% PAN/cellulose composite solution shows the best solution homogeneity. During gel spinning, the cellulose forms elongated particles inside the gelation bath, and the particle diameters depend on the as-spun draw ratio. It was found that the glass transition of PAN fibers shifts to higher temperatures along with the increase of cellulose content, and the glass transition activation energy of PAN chains becomes higher when cellulose particles become smaller. Regardless the changes of cellulose amount (2–10 wt%) and particle diameter (7.1–1.4 μm), the cyclization activation energy of PAN/cellulose composite fibers is 13–17% lower than that of neat PAN fibers. Our experiments suggest that the addition of cellulose in PAN fibers has no direct effect on the cyclization reaction of PAN chains. Instead, the released by-products during the pyrolysis of cellulose at high temperature degradation affect the cyclization reaction of PAN chains.     

Effect of solution extrusion rate on morphology and performance of polyvinylidene fluoride hollow fiber membranes using polyvinyl pyrrolidone as an additive

<正>Polyvinylidene fluoride(PVDF) hollow fiber membranes prepared from spinning solutions with different polyvinyl pyrrolidone(PVP) contents(1%and 5%) at different extrusion rates were obtained by wet/dry phase process keeping all other spinning parameters constant.In spinning these PVDF hollow fibers,dimethylacetamide(DMAc) and PVP were used as a solvent and an additive,respectively.Water was used as the inner coagulant.Dimethylformamide(DMF) and water(30/70) were used as the external coagulant.The performances of membranes were characterized in terms of water flux,solute rejection for the wet membranes.The structure and morphology of PVDF hollow fiber were examined by BET adsorption,dry/wet weight method and scanning electron microscopy(SEM).It is found that the increase in PVP content and extrusion rate of spinning solution can result in the increase of water flux and decrease of solute rejection.The improvements of interconnected porous structure and pore size are induced by shear-thinning behavior of spinning solution at high extrusion rates,which could result in the increase of water flux of hollow fiber membranes.The increase of extrusion rate also leads to the increase of membrane thickness due to the recovery effect of elastic property of polymer chains.     

蜘蛛吐丝过程中钾的作用

用电感耦合等离子体质谱(ICP-MS)对蜘蛛Nephila丝腺体和丝进行测定,结果表明,钾在丝中的含量明显高于在丝腺体中的含量.同时,在蜘蛛丝蛋白溶液中加入氯化钾,溶液出现乳白色浑浊,表明有呈β-折叠构象的微纤产生.浊度测试发现,丝蛋白微纤会逐渐聚集成较大颗粒而在溶液中形成沉淀.另外,红外光谱和拉曼光谱亦证明钾能够使蜘蛛丝蛋白膜发生从无规线团/螺旋到β-折叠的构象转变.有理由认为钾在蜘蛛吐丝过程中起重要作用,它的存在有利于丝蛋白形成β-折叠结构.     

海藻酸盐/壳聚糖衍生物复合抗菌纤维

通过溶液纺丝法制备海藻酸盐/羧甲基壳聚糖（CMC）共混纤维,并用红外光谱,X射线衍射和扫描电镜对共混纤维进行了表征.结果表明：共混体系中的两种组分之间存在着较强的相互作用,有良好的相容性.当ωCMC=0.30时,共混纤维的干态抗张强度达到最大值,13.8cN/tex.当ωCMC=0.10时,纤维的干态断裂伸长率可达23.1%.纤维的湿态抗张强度和断裂伸长率随着CMC含量的增加而降低.CMC的引入,可显著提高纤维的吸水率.用壳聚糖季铵盐对纤维进行处理,可赋予纤维抗菌性.     

Microfluidic fabrication of β-phase enriched poly(vinylidene fluoride) microfibers toward flexible piezoelectric sensor

β-phase enriched piezoelectric poly(vinylidene fluoride) (PVDF) films/fibers are often prepared by high-energy costing methods, including mechanical stretching, high-electric field or electrospinning. In this study, PVDF piezoelectric microfibers, for the first time, were prepared by microfluidic spinning technology. The β-phase enriched PVDF microfibers with various diameters could be easily obtained inside the microfluidic channel due to the mass transfer induced phase inversion of the inner PVDF solution. The influence of diameter of the fibers, PVDF concentration of the inner phase and water content of the outer phase on the β-phase content and crystallinity degree of the obtained fibers was studied in detail. The obtained β-phase enriched fiber was weaved into meshes. Flexible piezoelectric fabrics were then developed based on these meshes, and further used as in-situ and real time human motion monitoring. This simple and effective strategy provides a promising microfluidic spinning technique toward the development of functional microfibers and wearable piezoelectric sensors, which may also give some implies for the industrial wet-spinning of piezoelectric PVDF fibers in the future.     

Propolis Integration Methods into Solutions for Highly Loaded Propolis Fibers by Needleless Electrospinning

A load-bearing matrix filled with biologically active compounds is an efficient method for transporting them to the target location. Bee-made propolis has long been known as a natural product with antibacterial and antiviral, anti-inflammatory, antifungal properties, and anti-oxidative activity. The aim of the research is to obtain stable propolis/PVA solutions and produce fibers by electrospinning. To increase propolis content in fibers as much as possible, various types of propolis extracts were used. As a result of the research, micro- and nano-fiber webs were obtained, the possible use of which have biomedical and bioprotective applications. All used materials are edible and safe for humans, and fiber webs were prepared without using any toxic agent. This strategy overcomes propolis processing problems due to limitations to its solubility. The integration of different combinations of extracts allows more than 73 wt% of propolis to be incorporated into the fibers. The spinning solution preparation method was adapted to each type of propolis, and by combining the methods, solutions with different propolis extracts were obtained. Firstly, the total content of flavonoids in the propolis extracts was determined for the assessment and prediction of bioactivity. The properties of the extracts relevant for the preparation of electrospinning solutions were also evaluated. Secondly, the most appropriate choice of PVA molecular weight was made in order not to subject the propolis to too high temperatures (to save resources and not reduce the bioactivity of propolis) during the solution preparation process and to obtain fibers with the smallest possible diameter (for larger surface-to-volume ratios of nanofibers and high porosity). Third, electrospinning solutions were evaluated (viscosity, pH, conductivity and density, shelf life) before and after the addition of propolis to predict the maximum propolis content in the fibers and spinning stability. Each solution combination was spun using a cylindrical type electrode (suitable for industrial production) and tested for a stable electrospinning process. Using adapted solution-mixing sequences, all the obtained solutions were spun stably, and homogeneous fibers were obtained without major defects.