Anneal temperature dependence of Si/SiO2 superlattices photoluminescence

Photoluminescence spectroscopy, Fourier transform infrared spectroscopy, X-ray reflectometry and high resolution electron microscopy have been used to interpret the photoluminescence properties of annealed (3/19 nm) Si/SiO₂ multilayers grown by reactive magnetron sputtering. The multilayers show an emission in the visible and near-infrared range after heat treatment from 900°C which tends to decrease from 1200°C. Three different origins for the photoluminescence activity have been found. An anneal temperature of 1200°C is necessary to optimise the silicon crystallisation within the silicon sublayers.     

Defect driven ferroelectricity and magnetism in nanocrystalline KTaO3

Nominally pure nanocrystalline KTaO₃ was thoroughly investigated by micro-Raman and magnetic resonance spectroscopic techniques. In all samples the defect driven ferroelectricity and magnetism are registered. Both ordering states are suggested to appear due to the iron atoms and oxygen vacancies. The concentration of defects was estimated to be 0.04 and 0.06-0.1 mol%. Note that undoped single crystals of KTaO₃ are nonmagnetic and have never exhibited ferromagnetic properties. The results enable us to refer a nanosized KTaO₃ to the class of multiferroics and assume that it could perform the magnetoelectric effect at T<29 K. It was also established that the critical concentration of impurity defects necessary to provoke the appearance of the new phase states in the material strongly correlates with the size of the particle; as the size of the particle decreases, the critical concentration decreases as well.     

Study of superstructure II in multiferroic BiMnO3

The crystal structure of the minor phase, named superstructure II, existing in multiferroic compound BiMnO3 has been studied by electron diffraction and high-resolution transmission electron microscopy. Domains of major and minor phases coexisting in BiMnO3 were observed in high-resolution electron microscope images. The unit cell of minor phase was determined to be triclinic with the size 4×4×4 times as large as the distorted perovskite subcell. The [111] and [101] projected structure maps of the minor phase have been derived from the corresponding images by means of the image processing. A possible rough three-dimensional （3D） structure model was proposed based on the 3D structural information extracted from the two projected structure maps. Since there is no inversion centre in the proposed model, the minor phase may contribute to the ferroelectric property of BiMnO3.     

Characterization of Si nanocrystals into SiO2 matrix

Silicon nanocrystals (nc-Si) have gained great interest due to their excellent optical and electronic properties and their applications in optoelectronics. The aim of this work is the study of growth mechanism of nc-Si into a-SiO₂ matrix from SiO/SiO₂ multilayer annealing, using non-destructive and destructive techniques. The multilayer were grown by e-beam evaporation from SiO and SiO₂ materials and annealing at temperatures up to 1100 °C in N₂ atmosphere. X-rays reflectivity (XRR) and high resolution transmission electron microscopy (HRTEM) were used for the structural characterization and spectroscopic ellipsometry in IR (FTIRSE) energy region for the study of the bonding structure. The ellipsometric results gave a clear evidence of the formation of an a-SiO₂ matrix after the annealing process. The XRR data showed that the density is being increased in the range from 25 to 1100 °C. Finally, the HRTEM characterization proved the formation of nc-Si. Using the above results, we describe the growth mechanism of nc-Si into SiO₂ matrix under N₂ atmosphere.     

Unusual piezoresponse behavior across the grain boundary of PbMg1/3Nb2/3O3-0.33PbTiO3 thin films

Ferroelectric PbMg_1/3Nb_2/3O₃-0.33PbTiO₃ (PMN-0.33PT) polycrystalline thin film near MPB was grown on Ir with LaNiO₃ buffer layer by pulsed laser deposition technology. Piezoresponse force microscopy (PFM) was employed to investigate the role of grain boundary on the domains formation and their local physical properties in PMN-PT thin film. Unusual piezoresponse behaviors were firstly observed across the grain boundary of PMN-PT thin film via PFM. Such abnormal phenomenon is ascribed to the structural incompatibility-induced local stress across the grain boundary, which gives a deep influence on the local imprint behavior of PMN-PT thin film.     

The ν1 and ν3 stretching fundamental bands of PD3

The infrared (IR) spectrum of PD₃ has been recorded in the 1580–1800 cm⁻¹ range at a resolution of 0.0027 cm⁻¹. About 2400 rovibrational transitions with J^′=K^′22 have been measured and assigned to the ν₁ (A₁) and ν₃ (E) stretching fundamentals. These include 506 “perturbation-allowed” transitions with selection rules Δ(k−l)=±3. Splittings of the K^′′=3 lines have been observed. Effects of strong perturbations are evident in the spectrum. Therefore the rovibrational Hamiltonian adopted for the analysis explicitly takes into account the Coriolis and k-type interactions between the v₁=1 and v₃=1 states, and includes also several essential resonances within these states. The rotational structure in the v₁=1 and v₃=1 vibrational states up to J^′=K^′=18 was reproduced by fitting simultaneously all experimental data. Thirty-four parameters reproduced 1950 transitions retained in the final cycle with a standard deviation of the fit equal to 4.9 × 10⁻⁴ cm⁻¹ (about the precision of the experimental measurements).     

Er3+/Yb3+共掺Gd3Sc2Ga3O12晶体的上转换发光

研究了提拉法生长的Er³⁺/Yb³⁺:Gd₃Sc₂Ga₃O₁₂和Er³⁺:Gd₃Sc₂Ga₃O₁₂晶体在室温下320—1700nm范围的吸收光谱和500—750nm范围内的上转换荧光谱,同时对其上转换荧光的可能发生机制、途径以及上转换过程可能对Er^{3+相似文献}   

Effect of polar distortion on electronic structures of (001) LaGaO3/SrTiO3 interface

First-principles calculations of electronic structures of (001) epitaxial LaGaO₃/SrTiO₃ heterostructures were performed in the framework of density functional theory. The effects of atomic relaxation on electronic characteristics of both n-type (LaO)⁺/(TiO₂)⁰ and p-type (GaO₂)⁻/(SrO)⁰ interfaces are investigated. It is found that the n-type interface remains metallic, whereas the p-type interface becomes insulating after atomic relaxation. Polar distortion in the LaGaO₃ layers associated with the atomic relaxation strongly screens the intrinsic electric field induced by periodically stacking (LaO)⁺ and (GaO₂)⁻ charged atomic layers on SrTiO₃ with charge neutral (001) atomic layers. This relieves the trend to a polar catastrophe and reduces the carrier charge density on the interface.     

Microstructure of interfaces between a magnesium matrix and preoxidized silicon carbide particles

An amorphous SiO₂ layer, 100–150 nm thick, has been produced on the surface of -SiC particles by controlled oxidation in air. The as-treated particles were immersed for 1.5h at 1,000 K in a large excess of liquid magnesium, which resulted in the formation by pressureless infiltration of a composite region with a particle volume fraction about 50%. Conventional transmission electron microscopy (CTEM) and high-resolution TEM (HRTEM) were used to characterize and localize the different species present in the transition zone between the Mg matrix and the -SiC particles. The results are discussed in terms of the physico-chemical processes occurring during formation of the composite region or during cooling of the Mg ingot. A reaction mechanism based on local equilibria and liquid phase diffusion is proposed. Four steps are involved in this mechanism: (i) rapid conversion of SiO₂ into MgO and Si; (ii) formation of a true Mg/SiC interface; (iii) partial decomposition of SiC into carbon and silicon; and (iiii) precipitation of -SiC and Mg₂Si on cooling.     

Theoretical explanation of g factors for Ti ions in LiNbO3 and LiTaO3 crystals

The EPR g factors g_// and g_⊥ for Ti³⁺ ions at the trigonal octahedral Li⁺ sites of LiNbO₃ and LiTaO₃ crystals are calculated from the third-order perturbation formulas of g factors for 3d¹ ion in trigonal symmetry. In the calculations, the crystal-field parameters are obtained from the structural data by using the superposition model. The calculated values are in reasonable agreement with the observed values. The results are discussed.     

Investigation on spectral features of tungsten ions in PbO-Bi2O3-As2O3 glass matrix

Lead bismuth arsenate glasses mixed with different concentrations of WO₃ (ranging from 0 to 6.0 mol%) were synthesized. Differential thermal analysis (DTA), optical absorption, ESR and IR spectral studies have been carried out. The results of DTA have indicated that there is a gradual decrease in the resistance of the glass against devitrification with increase in the concentration of WO₃ upto 4.0 mol%.The optical absorption spectra of these glasses exhibited a relatively broad band peaking at about 880 nm identified due to d_xy→d_x²_−y² transition of W⁵⁺ ions; this band is observed to be more intense in the spectrum of glass containing 4.0 mol% of WO₃. Further, two prominent kinks attributed to ³P₀→¹S₀, ¹D₂ transitions of Bi³⁺ ions have also been located in the absorption spectra. The ESR spectra of these glasses recorded at room temperature exhibited an asymmetric signal at g_⊥∼1.71 and g_ll∼1.61. The intensity of the signal is observed to be maximal for the spectrum of the glass W₄. The quantitative analysis of optical absorption and ESR spectral studies have indicated that there is a maximum reduction of tungsten ions from W⁶⁺ state to W⁵⁺ state in the glass containing 4.0 mol% of WO₃. The IR spectral studies have indicated that there is a increasing degree of disorder in the glass network with increase in the concentration of WO₃ upto 4.0 mol%.     

用阴极发光显微术研究YAG:Nd~(3+)晶体中的缺陷

采用扫描电子显微镜中的阴极发光显微术获得了YAG:Nd~(3+)激光晶体中不同缺陷所形成的显微发光图象。据此进一步分析了这些缺陷的形成机制及其对材料性能的影响。     

Microstructural stability and age-hardening behavior of Re-added dual two-phase Ni3Al and Ni3V intermetallic alloys

The effect of Re addition on the microstructure and hardening behaviour of the dual two-phase Ni₃Al (L1₂) and Ni₃V (D0₂₂) intermetallic alloy was investigated by scanning electron microscopy, transmission electron microscopy and Vickers hardness test. The two-phase eutectoid microstructure accompanying the Re-rich precipitates were observed in the channel region of the alloys in which Re substituted for Ni but not in those in which Re substituted for Al and V. The concomitant addition of Nb (or Ta) with Re more stabilized the two-phase eutectoid microstructure and consequently more induced the fine precipitates in the channel region. The annealing at temperatures below the eutectoid temperature was necessary to induce the fine precipitates in the channel region and thereby result in the precipitation hardening. The fine precipitation in the channel region and related hardening was attributed to the alloying feature so that Re is soluble in the A1 (fcc) phase at high temperatures and becomes less soluble in the two intermetallic phases decomposed from the A1 phase at low temperatures.     

强冲击压缩下LiF，Al2O3和LiTaO3单晶的透光性

在二级轻气炮上，用高速电子相机扫描照相技术和改进的Mallory实验装置，对z切LiF，Al₂O₃(蓝宝石)和LiTaO₃单晶材料的冲击透光性进行了对比测量，并用黑密度计提取出动态图像定量化的光强对比度变化曲线.结果表明，LiF单晶在102 GPa压强下能够保持长时间的初始透光性不变，与公认的LiF具有优良的高压下透明性的认识一致.LiTaO₃单晶在实验压力(139GPa)下变成基本不透明.而Al_{关键词： 2}O₃')" href="#">Al₂O₃ LiF 3')" href="#">LiTaO₃ 光学透明性     

Luminescence of CsPbBr3-like quantum dots in CsBr single crystals

Luminescence and decay kinetics of the Pb²⁺ aggregates in CsBr host crystals were measured in the 4–300 K temperature interval and in 10⁻¹⁰–10⁻³ time scale. Their emission properties are similar to those of CsPbBr₃ bulk crystal showing a subnanosecond free exciton emission in the 520–540 nm spectral region and slower trapped exciton emission in the 530–580 nm spectral region. An efficient energy exchange between the free and trapped exciton states is shown by the temperature dependencies of emission spectra. The quantum size effect is demonstrated in the high energy shift and broadening of the absorption and emission spectra and an estimate of the size of the CsPbBr₃-like aggregates is provided. Independent evidence of the presence of the CsPbBr₃ and Cs₄PbBr₆ aggregated phases in the CsBr host was obtained by X-ray structural studies.     

X-ray study on the phase transitions in triammonium hydrogen disulfate crystals and deuterated crystals

The structural phase transitions in triammonium hydrogen disulfate crystals and deuterated crystals below room temperature have been studied by X-ray diffraction. Three phases are observed in the temperature range from 25°C down to — 160°C. The space groups in three different phases are identified as C2/c, P2/n (or Pn), and C2 for (NH₄)₃H(SO₄)₂ and (ND₄)₃D(SO₄)₂ crystals. No isotope effect on the structural phase transitions in these crystals could be detected by these studies. The occurrence of structural phase transitions caused by the reorientation of SO₄ groups and/or the shift of oxygen atoms from the sulfate atom in the SO₄ group are suggested from the diffraction photographs.     

Use of confocal laser scanning microscopy (CLSM) for depthwise resolved microscale-particle image velocimetry (μ-PIV)

A novel use of confocal laser scanning microscopy (CLSM) makes the truly focused field-of-view with well-defined depthwise resolution possible for microscale particle image velocimetry (μ-PIV) applications. The operating principle of the CLSM is presented using the point spread function (PSF) that describes diffracted images of extremely small particles. The implemented high-speed CLSM system using a Nipkow rotating disk is applied to measure the microscale rotating Couette flow field confined between two parallel horizontal disks that are 180-μm apart, with the bottom one stationary and the top one rotating and seeded by 200-nm fluorescent spheres. The CLSM provides much distinct particle images in comparison with the conventional wide-field microscopy (WFM) and the measured vector profiles are more concentric and accurate depicting closer to an ideal Couette flow.     

Nanocomposites of Poly(vinyl alcohol) Reinforced with Chemically Modified AL2O3: Synthesis and Characterization

The surface of α-alumina (Al₂O₃) nanoparticles was first modified with γ-aminopropyltriethoxy silane as a coupling agent. Then a series of poly(vinyl alcohol)/ surface modified Al₂O₃ nanocomposite suspensions were prepared in ethanol by a simple ultrasonic irradiation process. Composite films with 5, 10, and 15 wt % of inorganic Al₂O₃ nanoparticles were achieved after solvent evaporation. The formation of the composite materials were confirmed by Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and optical transparencies. The FE-SEM and TEM results showed a homogenous dispersion of nanoscale inorganic particles in the poly(vinyl alcohol) matrix. TGA thermographs showed that the thermal stability of the prepared Al₂O₃-reinforced nanocomposites was improved, increasing with increasing content of the nanoparticles. According to the optical transparencies, the optical clarity of poly(vinyl alcohol)/Al₂O₃ nanocomposite films was only slightly affected by the presence of the Al₂O₃ content.