Determination of trace elements in biological samples treated with formic acid by inductively coupled plasma mass spectrometry using a microconcentric nebulizer

A simple and fast method for the determination of As, Ba, Cd, Co, Cu, Fe, Ga, Mn, Mo, Ni, Pb, Rb, Se, Sr, Tl, U, V and Zn in biological samples by inductively coupled plasma mass spectrometry (ICP-MS), after sample solubilization with formic acid and introduction by a microconcentric nebulizer, is proposed. The sample is mixed with formic acid, kept at 90 °C for one hour and then diluted with nitric acid aqueous solution to a 50% v/v formic acid and 1% v/v nitric acid final concentrations. The final sample solution flow rate for introduction into the plasma was 30 μL min⁻¹. The optimized and adopted nebulizer gas flow rate was 0.7 L min⁻¹ and RF power was 800 W. These conditions are very different than those normally used when a conventional nebulizer is employed. Rodhium was used as internal standard. External calibration against aqueous standard solutions, without formic acid, could be used for quantification, except for As, Se and Zn. However, external calibration with 50% formic acid allows the determination of all analytes with high accuracy and it is recommended. The detection limits were between 0.0005 (Tl) and 0.22 mg kg⁻¹ (Fe) and the precision expressed by the relative standard deviations (RSD) were between 0.2% (Sr) and 3.5% (Ga). Accuracy was validated by the analysis of four certified reference biological materials of animal tissues, comparing the results by linear regressions and by the t-test at a 95% confidence level. The recommended procedure avoids plasma instability and carbon deposit on the cones.     

Determination of total mercury in biological samples using flow injection CVAAS following tissue solubilization in formic acid

Total mercury in biological samples was determined by flow injection (FI) cold vapour atomic absorption spectrometry (CVAAS) following tissue solubilization with formic acid. A mixture of potassium bromide and potassium bromate was used to decompose organomercury compounds prior to their reduction with sodium borohydride. A gold amalgam system was used to achieve lower detection limits when required. National Research Council Canada certified reference materials dogfish liver (DOLT-3), dogfish flesh (DORM-2) and lobster hepatopancreas (TORT-2), as well as oyster tissue (NIST SRM 1566b) and mussel tissue (NIST SRM 2976) were used to assess the accuracy of the method. The method of standard additions provided the most accurate results. Limit of detection (LOD) for Hg in the solid sample of 0.001 and 0.01 μg g⁻¹ were achieved with and without amalgamation, respectively. The precision of measurement for 1.6 ng ml⁻¹ methylmercury was 2.7% using the amalgam system.     

Direct determination of mercury in cosmetic samples by isotope dilution inductively coupled plasma mass spectrometry after dissolution with formic acid

A new method was proposed for the accurate determination of mercury in cosmetic samples based on isotopic dilution (ID)-photochemical vapor generation (PVG)-inductively coupled plasma mass spectrometry (ICP MS) measurement. Cosmetic samples were directly dissolved in formic acid solution and subsequently subjected to PVG for the reduction of mercury into vapor species following by ICP MS detection. Therefore, the risks of analyte contamination and loss were avoided. Highly enriched ²⁰¹Hg isotopic spike is added to cosmetics and the isotope ratios of ²⁰¹Hg/²⁰²Hg were measured for the quantitation of mercury. With ID calibration, the influences originating from sample matrixes for the determination of mercury in cosmetic samples have been efficiently eliminated. The effects of several experimental parameters, such as the concentration of the formic acid, and the flow rates of carrier gas and sample were investigated. The method provided good reproducibility and the detection limits were found to be 0.6 pg mL⁻¹. Finally, the developed method was successfully applied for the determination of mercury in six cosmetic samples and a spike test was performed to verify the accuracy of the method.     

Determination of arsenic, lead, selenium and tin in sediments by slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry using Ru as permanent modifier and NaCl as a carrier

A procedure for the determination of As, Pb, Se and Sn in sediment slurries by electrothermal vaporization inductively coupled plasma mass spectrometry is proposed. The slurry, 1 mg ml⁻¹, is prepared by mixing the sample ground to a particle size 50 μm with 5% v/v nitric and 1% v/v hydrofluoric acids in an ultrasonic bath. The slurry was homogenized with a constant flow of argon in the autosampler cup, just before transferring an aliquot to the graphite furnace. The tube was treated with Ru as a permanent modifier, and an optimized mass of 1 μg of NaCl was added as a physical carrier. The pyrolysis temperature was optimized through pyrolysis curves, and a compromised temperature of 800 °C was used; the vaporization temperature was 2300 °C. The effect of different acid concentrations in the slurry on the analyte signal intensities was also evaluated. The accuracy of the method was assured by the analysis of certified reference sediments MESS-2, PACS-2 and HISS-1 from the National Research Council Canada, SRM 2704 and SRM 1646a from the National Institute of Standards and Technology and RS-4 from a round robin test, using external calibration with aqueous standards prepared in the same medium as the slurries. The obtained concentrations were in agreement with the certified values according to the Student's t-test for a confidence level of 95%. The detection limits in the samples were: 0.17 μg g⁻¹ for As; 0.3 μg g⁻¹ for Pb; 0.05 μg g⁻¹ for Se and 0.28 μg g⁻¹ for Sn. The precision found for the different sediment samples, expressed as R.S.D. was 1–8% for As, 2–9% for Pb, 6–12% for Se and 3–8% for Sn (n=5).     

Analysis of fish otoliths by electrothermal vaporization inductively coupled plasma mass spectrometry: aspects of precipitating otolith calcium with hydrofluoric acid for trace element determination

A method is developed for determination of trace elements, including Ag, As, Cd, Co, Cr, Cu, Mn, Ni, Se, Tl and Zn, in fish otoliths by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS). Hydrofluoric acid was used to precipitate calcium resulting from acid dissolution of otolith calcium carbonate. Initial acidity of the sample solution influenced the precipitation efficiency of calcium fluoride. Up to 99.5% of Ca was precipitated in solutions that contained less than 2% (v/v) HNO₃. Recoveries of the elements obtained from spiked artificial otolith solutions were between 90 and 103%. Stabilization of the elements within the ETV cell was achieved with 0.3 μg Pd/0.2 μg Rh chemical modifier that also afforded optimum sensitivity for multielement determination. The method was validated by the analysis of a fish otolith reference material (CRM) of emperor snapper, and then applied to the determination of the trace elements in otoliths of several fish species captured in Raritan Bay, New Jersey. Results indicated that fish physiology and biological processes could influence the levels of Cu, Mn, Se and Zn in the otoliths of fish inhabiting a similar aqueous environment. Otolith concentrations of Cr and Ni did not show any significant differences among different species. Concentrations for Ag, As, Cd, Co and Tl were also not significantly different, but were very low indicating low affinity of otolith calcium carbonate to these elements.     

Determination of lithium in biological samples by inductively coupled plasma mass spectrometry

Lithium was determined in human serum by inductively coupled plasma mass spectrometry. Sample preparation was kept to the minimum: serum samples were diluted and beryllium was added as internal standard. Special attention was given to the choice of the internal standard and to the occurrence of memory effects. To test the accuracy of the method several biological reference materials were analysed, namely a “Second-Generation” Biological Reference Material (Freeze-Dried Human Serum) (University of Ghent), Human Serum SRM 909, Whole Egg Powder SRM 1845 and Mixed Human Diet SRM 1548 (National Institute of Standards and Technology). The results were compared with those obtained by other techniques. For the “second-generation” reference freeze-dried human serum a mean lithium concentration of 15.10 ng g^?1 with a standard deviation of 0.54 ng g^?1 dry weight was found. Analyses on serum samples from healthy individuals yielded lithium concentrations ranging from 0.22 to 0.97 μg l^?1.     

电热蒸发进样电感耦合等离子体原子发射光谱（ETV－ICP－AES）联用技术研究

本文采用国产部件组装了一套ＥＴＶ－ＩＣＰ－ＡＥＳ仪器体系，对装置的连接及操作参数进行优化。深入系统地考察了分析物的蒸发过程和传输过程，提出了难熔元素的蒸发和传输机理。研究了ＥＴＶ－ＩＣＰ－ＡＥＳ中基体效应，提出了以聚四氟乙烯为氟化剂，氟化辅助ＥＴＶ－ＩＣＰ－ＡＥＳ测定难熔元素的新方法，应用于环境和生物标样中痕量元素分析，获得满意结果。     

Electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry for the determination of Fe,Co, Ni,Cu, and Zn in biological samples

Slurry sampling electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry (ETV-DRC-ICP-MS) has been applied to determine Fe, Co, Ni, Cu, and Zn in biological samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Pd was used as the modifier. The effectiveness of the ETV sample introduction technique and dynamic reaction cell in alleviating various spectral interferences in ICP-MS analysis has been demonstrated. This method has been applied to determine Fe, Co, Ni, Cu, and Zn in NIST SRM 1573a tomato leaves reference material and NRCC DORM-2 dogfish muscle reference material and also real samples such as a tea and a swordfish sample purchased locally. Since the sensitivities of the elements studied in slurry and aqueous solution were different, an analyte addition technique was used for the determinations. The analytical results of the reference materials agreed with the certified values. The precision between sample replicates was better than 6% for all determinations. The method detection limit estimated from analyte addition curves was 0.01, 0.006, 0.007, 0.004, and 0.006 μg g⁻¹ for Fe, Co, Ni, Cu, and Zn, respectively, in the original biological samples.     

Determination of Cu, Mn, Ni and Sn in gasoline by electrothermal vaporization inductively coupled plasma mass spectrometry, and emulsion sample introduction

Trace metals in fuels, except in the case of additives, are usually undesirable and normally they occur in very low concentrations in gasoline, requiring sensitive techniques for their determination. Coupling of electrothermal vaporization with inductively coupled plasma mass spectrometry minimizes the problems related to the introduction of organic solvents into the plasma. Furthermore, sample preparation as oil-in-water emulsions reduces problems related to gasoline analysis. In this work, a method for determination of Cu, Mn, Ni and Sn in gasoline is proposed. Samples were prepared by forming a 10-fold diluted emulsion with a surfactant (Triton X-100), after treatment with concentrated HNO₃. The sample emulsion was pre-concentrated in the graphite tube by repeated pipetting and drying. External calibration was used with aqueous standards in a purified gasoline emulsion. Six samples from different gas stations were analyzed, and the analyte concentrations were found to be in the μg l⁻¹ range or below. The limits of detection were 0.22, 0.02, 0.38 and 0.03 μg l⁻¹ for Cu, Mn, Ni and Sn, respectively. The accuracy of the method was estimated using a recovery test.     

On the determination of platinum group elements in environmental materials by inductively coupled plasma mass spectrometry and microwave digestion

The interferences from Cd, Cu, Hf, Pb, Sr, Zn, Zr and Y on the inductively coupled plasma quadrupole mass spectrometry (ICP-MS) determination of Pt, Pd, Rh, Ru and Ir in geological (Pt-ore SARM-7, abundance range for platinum metals 0.07-3.74 μg/g) and environmental samples (sediment JSd-2 abundance range for Pt and Pd 0.0167-0.021 μg/g; road dust and plant sample) are evaluated using model solutions, real samples and comparison to inductively coupled plasma atomic emission spectrometry (ICP-AES) results. Pt, Rh, Ru and Ir can be determined usually after introduction of corrections for the interference in all investigated materials though in sediments the direct determination of Pt might be a problem depending on the actual Hf concentrations. The direct determination of Pd (after microwave-assisted acid digestion) is possible in ores using all investigated isotopes (, , ), in plants using and correction for the interferences of Zr, Mo and Cd, and not possible in sediments and road dust. Therefore, we developed a procedure for isolation of Pd using its diethyl-dithio-carabamate (DDTC) complex. The detection limits for Pt, Pd and Ir are 0.015 ng/g, and for Ru and Rh 0.03 ng/g.     

Determination of ultra-trace amount methyl-, phenyl- and inorganic mercury in environmental and biological samples by liquid chromatography with inductively coupled plasma mass spectrometry after cloud point extraction preconcentration

The cloud point extraction (CPE) preconcentration of ultra-trace amount of mercury species prior to reverse-phase high performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS) detection was studied. Mercury species including methyl-, ethyl-, phenyl- and inorganic mercury were transformed into hydrophobic chelates by reaction with sodium diethyldithiocarbamate, and the hydrophobic chelates were extracted into a surfactant-rich phase of Triton X-114 upon heating in a water bath at 40 °C. Ethylmercury was found partially decomposed during the CPE process, and was not included in the developed method. Various experimental conditions affecting the CPE preconcentration, HPLC separation, and ICP-MS determination were optimized. Under the optimized conditions, detection limits of 13, 8 and 6 ng l⁻¹ (as Hg) were achieved for MeHg⁺, PhHg⁺ and Hg²⁺, respectively. Seven determinations of a standard solution containing the three mercury species each at 0.5 ng ml⁻¹ level produced relative standard deviations of 5.3, 2.3 and 4.4% for MeHg⁺, PhHg⁺ and Hg²⁺, respectively. The developed method was successfully applied for the determination of the three mercury species in environmental water samples and biological samples of human hair and ocean fish.     

On the possibilities of inductively coupled plasma mass spectrometry for analysis of archaeological bones for reconstruction of paleodiet

The possibilities of inductively coupled plasma atomic mass spectrometry for determination of elemental composition of archaeological bones for reconstruction of paleodiet are discussed. The interferences of different polyatomic ions on the determination of Fe, Cu, Mg, Mn, Zn, and Zr are investigated and evaluated. Thus, a method for the determination of Al, As, Ba, Mg, Pb, Sr, V, Zn, and Zr is proposed and is validated by analysis of IAEA-SRM-H-5 (animal bone). The applicability of the proposed procedure is demonstrated analyzing real archaeological bone samples dated to 4th century b.c. and the results are compared with the data obtained by inductively coupled plasma atomic emission spectrometry.     

Analytical evaluation of electrothermal vaporization/low-pressure inductively coupled plasma atomic emission spectrometry for trace elemental analysis in microliter samples

A novel method for the determination of trace elements in microliter samples using the tantalum filament electrothermal vaporization/low-pressure inductively coupled plasma (ETV/LP-ICP) atomic emission spectrometry has been developed. An improved tantalum filament ETV was directly coupled with LP-ICP system for efficient vaporization of microliter samples and further quantitative analysis. The experimental parameters including ETV current, rf power and mass flow rate of argon carrier gas were optimized using the copper emission signal produced by 5 μl of standard solution (5 μg/ml). Under the optimized condition, the analytical performances including linearity, precision and detection limit for the developed system were investigated. Absolute detection limits in the range of 22–391 pg for selected eight elements (Fe, Cu, Cr, Mn, Pb, K, Zn and Mg) were obtained with satisfactory precision (<8.9% RSD). The feasibility of the developed system has been demonstrated by analyzing wheat gluten NIST standard sample.     

The use of carbon nanofibers microcolumn preconcentration for inductively coupled plasma mass spectrometry determination of Mn,Co and Ni

Based on carbon nanofibers (CNFs) as a solid phase extraction adsorbent, a microcolumn preconcentration method coupled to inductively coupled plasma mass spectrometry (ICP–MS) was developed for the determination of trace elements (Mn, Co and Ni). The effect of various experimental parameters such as pH, sample flow rate and volume, elution solution and interfering ions on the retention of the studied ions have been investigated systematically. During all the steps of the experimental process, Mn, Co and Ni could be quantitatively sorbed on the microcolumn containing CNFs in the range of pH 6.0–9.0, and then eluted completely with 0.5 mol ml^− 1 HNO₃. A preconcentration factor of 150-fold was obtained. The detection limits for Mn, Co and Ni were 40, 0.4 and 8.0 pg ml^− 1, respectively, with relative standard deviations less than 6.0%. In order to validate the proposed method, two certified reference materials of human hair (GBW 07601) and mussel (GBW 08571), and water sample were analyzed with satisfactory results. The recoveries were between 95.0 and 114%.     

Isotopic determination of selenium in biological materials with inductively coupled plasma mass spectrometry

A method for the isotopic determination of selenium in biological matrices is described. The method is based on hydride generation inductively coupled plasma mass spectrometry (ICP-MS). The development is specifically related to the requirements of stable isotope tracer studies in human subjects. The method is based on isotope dilution using 82Se as the in vitro spike and can quantify the 74Se and 77Se contents of samples. It involves wet oxidation (HNO3 - H2O2 or HNO3 - HClO4) of the 82Se-spiked matrix, reduction to selenite by boiling with HCl followed by measurement of the isotope ratios (82Se/77Se and 74Se/77Se) in the gas stream (H2Se) generated from on-line reduction of the sample selenite with NaBH4. Compared with the isotopic signal resulting from a selenite solution containing 5 ng ml-1 of Se, the total sample blank contributions at m/z = 74, 77 and 82 were less than 5% of the respective isotope signal. Worst-case absolute detection limits were 0.2-0.9 ng of Se, depending on the isotope used. Ion beam intensity ratios were measured with an over-all precision [relative standard deviation (RSD)] of 1% for both isotope pairs. Measured ratios (MRa/b) were stable during a given day's operation within the expected precision of the measurements but varied for different days. The magnitude of MRa/b was generally independent of the nature of the matrix. Highly linear relationships were found between ion beam intensity ratios (MRa/b) and the corresponding true isotope ratios for calibration solutions whose isotope ratios had been altered by as much as one order of magnitude.(ABSTRACT TRUNCATED AT 250 WORDS)     

Preconcentration and determination of ultra trace amounts of arsenic(III) and arsenic(V) in tap water and total arsenic in biological samples by cloud point extraction and electrothermal atomic absorption spectrometry

A new approach for developing a cloud point extraction-electrothermal atomic absorption spectrometry has been described and used for determination of arsenic. The method is based on phase separation phenomenon of non-ionic surfactants in aqueous solutions. After reaction of As(V) with molybdate towards a yellow heteropoly acid complex in sulfuric acid medium and increasing the temperature to 55 °C, analytes are quantitatively extracted to the non-ionic surfactant-rich phase (Triton X-114) after centrifugation.To decrease the viscosity of the extract and to allow its pipetting by the autosampler, 100 μl methanol was added to the surfactant-rich phase. An amount of 20 μl of this solution plus 10 μl of 0.1% m/v Pd(NO₃)₂ were injected into the graphite tube and the analyte determined by electrothermal atomic absorption spectrometry.Total inorganic arsenic(III, V) was extracted similarly after oxidation of As(III) to As(V) with KMnO₄. As(III) was calculated by difference. After optimization of the extraction condition and the instrumental parameters, a detection limit (3σ_B) of 0.01 μg l⁻¹ with enrichment factor of 52.5 was achieved for only 10 ml of sample. The analytical curve was linear in the concentration range of 0.02-0.35 μg l⁻¹. Relative standard deviations were lower than 5%. The method was successfully applied to the determination of As(III) and As(V) in tap water and total arsenic in biological samples (hair and nail).     

Oxygen bomb combustion of biological samples for inductively coupled plasma optical emission spectrometry

A rapid sample preparation method is proposed for decomposition of milk powder, corn bran, bovine and fish tissues, containing certified contents of the analytes. The procedure involves sample combustion in a commercial stainless steel oxygen bomb operating at 25 bar. Most of the samples were decomposed within 5 min. Diluted nitric acid or water-soluble tertiary amines 10% v/v were used as absorption solutions. Calcium, Cu, K, Mg, Na, P, S and Zn were recovered with the bomb washings and determined by inductively coupled plasma optical emission spectrometry (ICP-OES). Ethanol mixed with paraffin was used as a combustion aid to allow complete combustion. A cooling step prior releasing of the bomb valve was employed to increase the efficiency of sample combustion. Iodine was also determined in milk samples spiked with potassium iodide to evaluate the volatilization and collection of iodine in amine CFA-C medium and the feasibility of its determination by ICP-OES with axial view configuration. Most of the element recoveries in the samples were between 91 and 105% and the certified and found contents exhibited a fair agreement at a 95% confidence level.     

电感耦合等离子体质谱(ICP-MS)法测定地质样品中镉、铬、钨、钽和铌

地质样品成分复杂,各元素物理化学性质差异大,在有盐酸介质存在的的情况下,敞口湿法一次消解容易出现易挥发元素Cd、Cr等测定结果不稳定;敞口湿法一次消解,难溶元素W、Ta、Nb等消解不完全。本文以HNO3—HF—HClO4—H2SO4为消解体系,用电热板湿法重复消解样品,建立起了ICP-MS同时测定地质样品种不同性质Cd、Cr、W、Ta、Nb的样品分析方法。通过优化仪器参数条件,选择带碰撞池He气模式（ked）,以50g/L酒石酸为测定介质,采用三通在线加入103Rh和185Re内标补偿基体效应和信号飘逸,解决了难溶元素W、Ta、Nb结果偏低、易挥发元素Cd、Cr结果精密度较差的问题。该方法用国家一级标准物岩石、土壤、水系沉积物质验证,相对标准偏差(RSD)小于8%,准确度(△lgC)均≤0.05,其测定值与标准值一致,用实际样品进行加标回收试验,回收率在89%～110%之间,方法检出限均小于多目标区域地球化学调查规范（DZ/T 0258—2014）。该方法分析流程较简单,结果准确可靠,可满足测定大批量地质样品中Cd、Cr、W、Ta、Nb元素含量的要求。     

Direct determination of major elements in solid plant materials by electrothermal vaporization inductively coupled plasma atomic emission spectrometry

The present work demonstrates the capability of electrothermal vaporization (ETV) to become an important tool of solid sample introduction in ICP-AES for plant sample analysis. Direct determination of Al, Ca, Fe, K, Mg, Mn, Na and Zn was investigated in powdered plant samples. Obtaining good results for major elements in plant samples was governed by some special operating conditions. The sensitivity of the method necessitated the use of ICP in radial view configuration. The behavior of elements during vaporization was studied between 500 and 2600 °C. External calibration was carried out using solid external (cellulose) spiked with aqueous standard solutions. However, performances of the analytical method were found dependent of argon flow rates. Analytical accuracy of the method was tested in three reference materials. Analytical results agreed with certified values when cellulose was used in calibration. However, K could not be determined because of excessive sensitivity. Without cellulose, it was found that Fe results were underestimated and Zn results overestimated. Relative standard deviations varied from 3 to 23%. Limits of detection varied from 1 to 80 ng g⁻¹ from one element to the other for a typical mass sample of 2 mg.     

Microwave sample-digestion procedure for determination of arsenic in moss samples using electrothermal atomic absorption spectrometry and inductively coupled plasma mass spectrometry

Arsenic in moss samples was determined by electrothermal atomic absorption spectrometry (ETAAS) after microwave-assisted sample digestion. Two different sample masses (500 mg and 1000 mg) and three different microwave ovens were used in the digestion. There was a slight difference in the digestion efficiency, as determined by the residual carbon concentrations of 500 mg digested samples, between the microwave ovens. The arsenic results obtained for moss reference samples were, in most cases, satisfactory. However, phosphorus was found to have a reducing influence on the arsenic peak area in the ETAAS determination. According to the results, it was not possible to reduce the phosphorus interference by increasing the amount of Mg(NO(3))(2) in the Pd-Mg chemical modifier. The arsenic results obtained by ETAAS were compared to those obtained by inductively coupled plasma mass spectrometry (ICP-MS).